Tri-Color Top View 0404 <1.0 1.0 t=0.2mm> High Brightness Type SMLP34 Series (under development) Emitting Color Target Spec. Blue Part No. Green Material Red InGaN on SiC AlGalnP on GaAs Package Size(mm) SMLP34RGB1W 1010(0404) 1.0x1.0(t=0.2) Absolute Maximum Ratings (Ta=25C) Peak Forward Storage Reverse Operating forward current voltage temperature temperature current Topr Tstg VR IF1 IFP2 (V) (C) (C) (mA) (mA) Emitting dissipation color PD (mW) 1 0.6 anode mark G 1 Power Part No. Dimensions (Unit:mm) B R Blue 20 100 5 -30 to +85 -40 to +100 0.08 64 Green 0.2 +0.05 -0.02 SMLP34RGB1W Red 1:The above absolute maximum ratings are valid for the case of lighting a single color. When lighting two colors at the same time, each of the figures in the absolute maximum ratings should be reduced down to 50% of it. When lighting three colors, it will be reduced down to 30% of it. (DC drive) 2:Conditions of IFP : Pulse width 1ms Duty 1/120 Cathode mark 4-R0.15 0.92 Cathode Red Terminal 0.4 Electrical Optical Characteristics (Ta=25C) Part No. Resin Color Forward voltage VF Typ. (V) 3.0 (3.2) SMLP34RGB1W Milky White 3.1 (3.3) 1.9 (2.2) IF (mA) Reverse current IR Max. (A) Light wavelength 100 Brightness IV Directivity (Typ.) 3 D Typ. (nm) 5 527 624 Scanning Angle (deg) X-Y IF (mA) Min. ( mcd) Typ. (mcd) 5 9.0 (28) 36 (110) 14 (56) 18 (50) 71 (200) 28 (100) 470 5 (20) Anode Tolerance:0.1 Dominant VR (V) Blue Green 3:Measurement tolerance : 2nm ( IF (mA) G, B 0 G 30 30 B R 60 60 5 (20) 90 100 50 ) : reference R 0 50 90 100 RELATIVE LUMINOUS INTENSITY (%) Scanning Angle (deg) X'-Y' R, B 0 G 30 30 G B R 60 60 90 100 50 0 50 90 100 RELATIVE LUMINOUS INTENSITY (%) Recommended Pad Layout Packaging Specifications (Unit:mm) Tape Specifications:T1 <5,000pcs/reel> Reel Specifications 0.45 0.4 0.45 1.12 1.750.1 0.280.06 Tolerance: 0.2 180 -30 60 +10 13 1.120.05 4.00.05 0.200.08 3MAX (Unit:mm) The recommended thickness of the screen mask for soldering is between 80 and 130m. The hole size of the screen mask should be same as the recommended land pattern or smaller. 3.50.05 1.5 +0.1 0 1.12 2.00.05 8.00.2 0.45 0.4 0.45 Feeding direction 4.00.1 Label Position Tolerance:0.2 11.41 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright (c) 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0