83.02.0.240.0000 - FINDER - Datasheet.Live

83.01 83.02

1 CO (SPDT) 2 CO (DPDT)

16/30 10/30

250/400 250/400

4,000 2,500

750 750

0.5 0.5

16/0.3/0.12 10/0.3/0.12

300 (5/5) 300 (5/5)

AgNi AgNi

24…240 24...240

< 1.5 / < 2 < 2 / < 2

16.8...265 16.8...265

(0.05…1)s, (0.5…10)s, (0.05…1)min, (0.5...10)min, (0.05...1)h, (0.5...10)h, (0.05...1)d, (0.5...10)d

± 1 ± 1

200 200

50 50

± 5 ± 5

70·103150·103

–20…+60 –20…+60

IP 20 IP 20

Wiring diagram

(without control signal)

•Multi-voltage

•Multi-function

•

Timing can be regulated using ext. Potentiometer

•

2 timed contacts or 1 timed + 1 instantaneous contact

•Multi-voltage

•Multi-function

AI: On-delay

DI: Interval

GI: Pulse delayed

SW: Symmetrical flasher (starting pulse on)

BE: Off-delay with control signal

CE: On- and off-delay with control signal

DE: Interval with control signal on

WD: Watchdog (Retriggerable interval with control

signal on)

AI: On-delay

DI: Interval

GI: Pulse delayed

SW: Symmetrical flasher (starting pulse on)

BE: Off-delay with control signal

CE: On- and off-delay with control signal

DE: Interval with control signal on

WD: Watchdog (Retriggerable interval with control

signal on)

Wiring diagram

(with control signal)

Wiring diagram

(with control signal)

Wiring diagram

(without control signal)

83 Series - Modular timers 10 - 16 A

Contact specification

Contact configuration

Rated current/Maximum peak current A

Rated voltage/Maximum switching voltage V AC

Rated load AC1 VA

Rated load AC15 (230 V AC) VA

Single phase motor rating (230 V AC) kW

Breaking capacity DC1: 30/110/220 V A

Minimum switching load mW (V/mA)

Standard contact material

Supply specification

Nominal voltage (UN) V AC (50/60 Hz)

V DC

Rated power AC/DC VA (50 Hz)/W

Operating range V AC

V DC

Technical data

Specified time range

Repeatability %

Recovery time ms

Minimum control impulse ms

Setting accuracy-full range %

Electrical life at rated load in AC1 cycles

Ambient temperature range °C

Protection category

Approvals (according to type)

Features

Multi-function timer range

83.01 - Multi-function & multi-voltage, 1 Pole

83.02 - Multi-function & multi-voltage,

2 Pole (timed + instantaneous options),

external time setting potentiometer

option

•22.5 mm wide

•Eight time scales from 0.05s to 10 days

•High input/output isolation

•Wide supply range (24...240)V AC/DC

•35 mm rail (EN 60715) mount

•“Blade + cross” - both flat blade and cross

head screw drivers can be used to adjust the

range and function selectors, the timing

trimmer, and to disengage the rail mounting

clip

•Multi-voltage versions with “PWM clever”

technology

For outline drawing see page 5

83.11 83.21 83.41

•Multi-voltage

•Mono-function

BE: Off-delay with control signal

Wiring diagram

(with control signal)

1 CO (SPDT) 1 CO (SPDT) 1 CO (SPDT)

16/30 16/30 16/30

250/400 250/400 250/400

4,000 4,000 4,000

750 750 750

0.5 0.5 0.5

16/0.3/0.12 16/0.3/0.12 16/0.3/0.12

300 (5/5) 300 (5/5) 300 (5/5)

AgNi AgNi AgNi

24...240 24...240 24...240

< 1.5 / < 2 < 1.5 / < 2 < 1.5 / < 2

16.8...265 16.8...265 16.8...265

(0.05…1)s, (0.5…10)s, (0.05…1)min, (0.5...10)min, (0.05...1)h, (0.5...10)h, (0.05...1)d, (0.5...10)d

± 1 ± 1 ± 1

200 200 200

——50

± 5 ± 5 ± 5

70·10370·10370·103

–20…+60 –20…+60 –20…+60

IP 20 IP 20 IP 20

•Multi-voltage

•Mono-function

AI: On-delay

Wiring diagram

(without control signal)

Contact specification

Contact configuration

Rated current/Maximum peak current A

Rated voltage/Maximum switching voltage V AC

Rated load AC1 VA

Rated load AC15 (230 V AC) VA

Single phase motor rating (230 V AC) kW

Breaking capacity DC1: 30/110/220 V A

Minimum switching load mW (V/mA)

Standard contact material

Supply specification

Nominal voltage (UN) V AC (50/60 Hz)

V DC

Rated power AC/DC VA (50 Hz)/W

Operating range V AC

V DC

Technical data

Specified time range

Repeatability %

Recovery time ms

Minimum control impulse ms

Setting accuracy-full range %

Electrical life at rated load in AC1 cycles

Ambient temperature range °C

Protection category

Approvals (according to type)

Features

Mono-function timer range

83.11 - ON-delay, multi-voltage

83.21 - Interval, multi-voltage

83.41 - Off-delay with control signal,

multi-voltage

•1 Pole

•22.5 mm wide

•Eight time scales from 0.05s to 10 days

•High input/output isolation

•Wide supply range (24...240)V AC/DC

•35 mm rail (EN 60715) mount

•“Blade + cross” - both flat blade and cross

head screw drivers can be used to adjust the

range and function selectors, the timing

trimmer, and to disengage the rail mounting

clip

•Multi-voltage versions with “PWM clever”

technology

Wiring diagram

(without control signal)

•Multi-voltage

•Mono-function

DI: Interval

83 Series - Modular timers 16 A

For outline drawing see page 5

83.62 83.82 83.91

•Multi-voltage

•Multi-function

LI: Asymmetrical flasher

(starting pulse on)

LE: Asymmetrical flasher (starting

pulse on) with control signal

PI: Asymmetrical flasher

(starting pulse off)

PE: Asymmetrical flasher (starting

pulse off) with control signal

Wiring diagram

(with control signal)

2 CO (DPDT) 2 NO (DPST-NO) 1 CO (SPDT)

8/15 16/30 16/30

250/400 250/400 250/400

2,000 4,000 4,000

400 750 750

0.3 0.5 0.5

8/0.3/0.12 16/0.3/0.12 16/0.3/0.12

300 (5/5) 300 (5/5) 300 (5/5)

AgNi AgNi AgNi

24...240 24...240 24...240

< 1.5 / < 2 < 1.5 / < 2 < 1.5 / < 2

16.8...265 16.8...265 16.8...265

***

± 1 ± 1 ± 1

200 200 200

500 ms (A1 - A2) — 50

± 5 ± 5 ± 5

100·10370·10370·103

–20…+60 –20…+60 –20…+60

IP 20 IP 20 IP 20

•Multi-voltage

•Mono-function

•2 pole

BI: Power off-delay (True off-delay)

Wiring diagram

(without control signal)

Contact specification

Contact configuration

Rated current/Maximum peak current A

Rated voltage/Maximum switching voltage V AC

Rated load AC1 VA

Rated load AC15 (230 V AC) VA

Single phase motor rating (230 V AC) kW

Breaking capacity DC1: 30/110/220 V A

Minimum switching load mW (V/mA)

Standard contact material

Supply specification

Nominal voltage (UN) V AC (50/60 Hz)

V DC

Rated power AC/DC VA (50 Hz)/W

Operating range V AC

V DC

Technical data

Specified time range

Repeatability %

Recovery time ms

Minimum control impulse ms

Setting accuracy-full range %

Electrical life at rated load in AC1 cycles

Ambient temperature range °C

Protection category

Approvals (according to type)

Features

Mono-function and multi-function timer range

83.62 - Power off-delay, multi-voltage, 2 Pole

83.82 - Star-Delta, multi-voltage,

star and delta output contacts

83.91 - Asymmetrical flasher, multi-voltage,

1 Pole

•22.5 mm wide

•Time scales:

Type 83.62 - 0.05s to 3 minutes

Type 83.82 / 83.91 - 0.05 s to 10 days

•Wide supply range (24…240)V AC / DC

•35 mm rail (EN 60715) mount

Wiring diagram

(without control signal)

Wiring diagram

(without control signal)

•Multi-voltage

•Mono-function

•2 pole

•Transfer time can be

regulated (0.05…1)s ***

SD: Star-delta

83 Series - Modular timers 8 - 16 A

* (0.05…2)s, (1…16)s, (8…70)s, (50…180)s

** (0.05…1)s, (0.5…10)s, (0.05…1)min,

(0.5...10)min, (0.05...1)h, (0.5...10)h,

(0.05...1)d, (0.5...10)d

*** 0.05 s, 0.2 s, 0.3 s, 0.45 s, 0.6 s, 0.75 s,

0.85 s, 1 s

For outline drawing see page 5

Example: 83 series, modular timers, 1 CO (SPDT) - 16 A, supply rated at (24…240)V AC/DC.

Versions

0000 = Standard

Supply voltage

240 = (24 ... 240)V AC/DC

Supply version

0 = AC (50/60 Hz)/DC

No. of poles

1 = 1 CO (SPDT)

2 = 2 CO (DPDT) for 83.02 and 83.62

2 = 2 NO (DPST-NO) for 83.82

Series

Type

0 = Multi-function (AI, DI, GI, SW, BE, CE, DE, WD)

1 = On-delay (AI)

2 = Interval (DI)

4 = Off-delay with control signal (BE)

6 = Power off-delay (True off-delay) (BI)

8 = Star-delta (SD)

9 = Asymmetrical flasher (LI, LE, PI, PE)

0 1 0

Ordering information

... .

24083

Insulation

Dielectric strength between input and output circuit V AC 4,000

between open contacts V AC 1,000

Insulation (1.2/50 μs) between input and output kV 6

EMC specifications

Type of test Reference standard

Electrostatic discharge contact discharge EN 61000-4-2 4 kV

air discharge EN 61000-4-2 8 kV

Radio-frequency electromagnetic field (80 ÷ 1,000 MHz) EN 61000-4-3 10 V/m

(1,000 ÷ 2,700 MHz) EN 61000-4-3 3 V/m

Fast transients (burst) (5-50 ns, 5 and 100 kHz) on Supply terminals EN 61000-4-4 6 kV

on control signal terminal (B1) EN 61000-4-4 6 kV

Surges (1.2/50 μs) on Supply terminals common mode EN 61000-4-5 6 kV

differential mode EN 61000-4-5 4 kV

on control signal terminal (B1) common mode EN 61000-4-5 6 kV

differential mode EN 61000-4-5 4 kV

Radio-frequency common mode (0.15 ÷ 80 MHz) EN 61000-4-6 10 V

on Supply terminals (80 ÷ 230 MHz) EN 61000-4-6 10 V

Radiated and conducted emission EN 55022 class B

Other data

Current absorption on control signal (B1) < 1 mA

- max cable length (capacity of ≤ 10 nF / 100 m) 150 m

- when applying a control signal to B1, which is B1 is isolated from A1 and A2 by an opto-coupler, and can

different from the supply voltage at A1/A2 therefore be operated at a voltage other than the supply

voltage.

If using a control signal of between (24... 48)V DC

and

a supply voltage of (24...240)V AC, ensure that the signal – is

connected to A2 and the + is applied to B1, and that L is

applied to B1 and N to A2.

External potentiometer for 83.02 Use a 10 kΩ/≥ 0,25 W linear potentiometer. Maximum cable

length 10 m. When using an external potentiometer, the timer

automatically use its setting in place of the internal setting.

Consider the voltage potential at the potentiometer to be the

same as the timer supply voltage.

Power lost to the environment without contact current W 1.4

with rated current W 3.2

Screw torque Nm 0.8

Max. wire size solid cable stranded cable

mm2 1x6 / 2x4 1x4 / 2x2.5

AWG 1x10 / 2x12 1x12 / 2x14

Technical data

83 Series - Modular timers 16 A

0 0 0 0

83 Series - Modular timers 16 A

Outline drawings

83.01

Screw terminal

83.02

Screw terminal

83.11

Screw terminal

83.21

Screw terminal

83.41

Screw terminal

83.62

Screw terminal

83.82

Screw terminal

83.91

Screw terminal

NO output

contact

Supply

voltage

LED*

OFF

Open

(Timing in Progress)

Closed

Open

Contacts

Closed

15 - 18 15 - 16

25 - 28 25 - 26

15 - 18 15 - 16

25 - 28 25 - 26

15 - 18 15 - 16

25 - 28 25 - 26

15 - 16 15 - 18

25 - 26 25 - 28

Functions

83 Series - Modular timers 16 A

* The LED on type 83.62 is illuminated when supply voltage is supplied to timer.

• Possible to control an external load, such as another relay coil or timer, connected to the control signal terminal B1.

* With DC supply, positive polarity has to be connected to B1 terminal (according to EN 60204-1).

** A voltage other than the supply voltage can be applied to the control signal (B1), example:

A1 - A2 = 230 V AC

B1 - A2 = 12 V DC

060.72

Accessories

Sheet of marker tags, for types 83.01/11/21/41/62/82, plastic, 72 tags, 6x12 mm 060.72

087.02.2

Z1 Z2

Potentiometer usable as external potentiometer for type 83.02 087.02.2

10 kΩ / 0.25 W linear

with control signal

Multi-function

without control signal Type

83.01

83.02

*** Type 83.02: regulated

using an external

potentiometer

(10 kΩ- 0.25 W).

***

(AI) On-delay.

Apply power to timer. Output contacts transfer after preset

time has elapsed. Reset occurs when power is removed.

(DI) Interval.

Apply power to timer. Output contacts transfer immediately.

After the preset time has elapsed, contacts reset.

(GI) Pulse delayed.

Apply power to timer. Output contacts transfer after preset

time has elapsed. Reset occurs after a fixed time of 0.5s.

(SW) Symmetrical flasher (starting pulse on).

Apply power to timer. Output contacts transfer immediately

and cycle between ON and OFF for as long as power is

applied. The ratio is 1:1 (time on = time off).

(BE) Off-delay with control signal.

Power is permenently applied to the timer. The output contacts

transfer immediately on closure of the control signal (S).

Opening the control signal initiates the preset delay, after which

time the output contacts reset.

(CE) On- and off-delay with control signal.

Power is permenently applied to the timer.

Closing the control signal (S) initiates the preset delay, after

which time the output contacts transfer. Opening the control sig-

nal initiates the same preset delay, after which time the

output contacts reset.

(DE) Interval with control signal on.

Power is permenently applied to the timer.

On momentary or maintained closure of control signal (S),

the output contacts transfer, and remain so for the duration

of the preset delay, after which they reset.

(WD) Watchdog (Retriggerable interval with control signal on).

Power is permanently applied to the timer.

On momentary or maintained closure of control signal (S),

the output contacts transfer, and remain so for the duration

of the preset delay, after which they reset; subsequent closures of

control signal during the delay will extend the time. If the closure

of the control signal (S) is longer than the preset time (T) then the

output contacts reset.

Both output contacts (15-18 and 25-28)

follow the timing function

2 timed contacts

1 timed +

1 instantaneous contact

Both output contacts (15-18 and 25-28)

follow the timing function

Both output contacts [15-18 and 25(21)-28(24)]

stay permanently open

Both output contacts [15-18 and 25(21)-28(24)]

stay permanently open

The output contact 15-18 follows the timing function

The output contact 21-24 follows the power supply (U)

The output contact 15-18 follows the timing function

The output contact 21-24 follows the control signal (S)

Wiring diagram

83.01

83.02

83 Series - Modular timers 16 A

83.02 type

NOTE: The timing function must be set when the timer is de-energised. Or for the 83.02, when the contact mode selector is in the OFF position.

Contact mode selector Functions without control signal (example: AI) Functions with control signal (example: BE)

Functions

U= Supply voltage S= Signal switch = Output contact

83.91

without control signal

Asymmetrical recycler

without control signal

Mono-function

with control signal (S)

Type

83.11

(AI) On-delay.

Apply power to timer. Output contacts transfer after preset

time has elapsed. Reset occurs when power is removed.

(DI) Interval.

Apply power to timer. Output contacts transfer immediately.

After the preset time has elapsed, contacts reset.

(BI) Power off-delay (True off-delay).

Apply power to timer (minimum 500 ms). Output contacts

transfer immediately. Removal of power initiates the preset

delay, after which time the output contacts reset.

(SD) Star-delta.

Apply power to timer. The star contact ( ) closes immediately.

After preset delay has elapsed the star contact ( ) resets.

After a further time (settable from 0.05s to 1s) the delta

contact ( Δ) closes and remains in that position, until reset on

power off.

(BE) Off-delay with control signal.

Power is permenently applied to the timer.

The output contacts transfer immediately on closure of the

control signal (S). Opening the control signal initiates the

preset delay, after which time the output contacts reset.

(LI) Asymmetrical flasher (starting pulse on)- (Z1-Z2 open).

Apply power to timer. Output contacts transfer immediately

and cycle between ON and OFF for as long as power is

applied. The ON and OFF times are independently

adjustable.

(PI) Asymmetrical flasher (starting pulse off) - (Z1-Z2 linked).

Apply power to timer. Output contacts transfer after time T1

has elapsed and cycle between OFF and ON for as long as

power is applied. The ON and OFF times are independently

adjustable.

(LE) Asymmetrical flasher (starting pulse on) with control

signal - (Z1-Z2 open).

Power is permenently applied to the timer.

Closing control signal (S) causes the output contacts to

transfer immediately and cycle between ON and OFF,

until opened.

(PE) Asymmetrical flasher (starting pulse off) with control

signal - (Z1-Z2 linked).

Power is permenently applied to the timer.

Closing the control signal (S) initiates delay T1 after which the

output contacts transfer and continue to cycle between OFF

and ON, until the control signal is opened.

83.11

83.21

83.82

83.41

83.91

Z1-Z2 open: (LI) function

Z1-Z2 linked: (PI) function

Z1-Z2 open: (LE) function

Z1-Z2 linked: (PE) function

83.91

Wiring diagram

Functions

83 Series - Modular timers 16 A

83.62

83.21

83.82

83.41

83.62

with control signal

U= Supply voltage S= Signal switch = Output contact