MC74HC390A Dual 4-Stage Binary Ripple Counter with / 2 and / 5 Sections High-Performance Silicon-Gate CMOS The MC74HC390A is identical in pinout to the LS390. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. This device consists of two independent 4-bit counters, each composed of a divide-by-two and a divide-by-five section. The divide-by-two and divide-by-five counters have separate clock inputs, and can be cascaded to implement various combinations of / 2 and/or / 5 up to a / 100 counter. Flip-flops internal to the counters are triggered by high-to-low transitions of the clock input. A separate, asynchronous reset is provided for each 4-bit counter. State changes of the Q outputs do not occur simultaneously because of internal ripple delays. Therefore, decoded output signals are subject to decoding spikes and should not be used as clocks or strobes except when gated with the Clock of the HC390A. Features * * * * * * * * * Output Drive Capability: 10 LSTTL Loads Outputs Directly Interface to CMOS, NMOS, and TTL Operating Voltage Range: 2.0 to 6.0 V Low Input Current: 1 mA High Noise Immunity Characteristic of CMOS Devices In Compliance with the Requirements Defined by JEDEC Standard No 7 A Chip Complexity: 244 FETs or 61 Equivalent Gates NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant (c) Semiconductor Components Industries, LLC, 2012 July, 2012 - Rev. 6 1 http://onsemi.com MARKING DIAGRAMS 16 PDIP-16 N SUFFIX CASE 648 16 1 MC74HC390AN AWLYYWWG 1 16 SOIC-16 D SUFFIX CASE 751B 16 1 HC390AG AWLYWW 1 16 HC 390A ALYWG G TSSOP-16 DT SUFFIX CASE 948F 16 1 1 A L, WL Y, YY W, WW G or G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. Publication Order Number: MC74HC390A/D MC74HC390A CLOCK Aa 1 16 VCC RESET a 2 15 CLOCK Ab QAa 3 14 RESET b CLOCK Ba 4 13 QAb QBa 5 12 CLOCK Bb QCa 6 11 QBb QDa 7 10 QCb GND 8 9 QDb CLOCK A 1, 15 /2 COUNTER 3, 13 QA 5, 11 CLOCK B RESET 4, 12 /5 COUNTER QB 6, 10 QC 7, 9 QD PIN 16 = VCC PIN 8 = GND 2, 14 Figure 1. Pin Assignment Figure 2. Logic Diagram FUNCTION TABLE Clock A B Reset Action X X H X L Reset / 2 and / 5 Increment /2 Increment /5 X L ORDERING INFORMATION Package Shipping MC74HC390ANG PDIP-16 (Pb-Free) 500 Units / Rail MC74HC390ADG SOIC-16 (Pb-Free) 48 Units / Rail MC74HC390ADR2G SOIC-16 (Pb-Free) 2500 / Tape & Reel MC74HC390ADTR2G TSSOP-16 (Pb-Free) 2500 / Tape & Reel NLV74HC390ADR2G* SOIC-16 (Pb-Free) 2500 / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC-Q100 Qualified and PPAP Capable http://onsemi.com 2 MC74HC390A IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII IIIII III IIIIIIIIIIIIIIIIIIIIIIIIII MAXIMUM RATINGS Symbol Parameter Value Unit - 0.5 to + 7.0 V DC Input Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V DC Output Voltage (Referenced to GND) VCC DC Supply Voltage (Referenced to GND) Vin Vout - 0.5 to VCC + 0.5 V Iin DC Input Current, per Pin 20 mA mA Iout DC Output Current, per Pin 25 ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air, 750 500 450 mW Tstg Storage Temperature - 65 to + 150 _C TL Lead Temperature, 1 mm from Case for 10 Seconds Plastic DIP, SOIC or TSSOP Package Plastic DIP SOIC Package TSSOP Package This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. _C 260 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Derating -- Plastic DIP: - 10 mW/_C from 65_ to 125_C SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: - 6.1 mW/_C from 65_ to 125_C IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIII IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIII III IIIIIIIII IIII IIII III IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII RECOMMENDED OPERATING CONDITIONS Symbol VCC Vin, Vout Parameter DC Supply Voltage (Referenced to GND) Min Max Unit 2.0 6.0 V 0 VCC V - 55 + 125 _C 0 0 0 0 1000 600 500 400 ns DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC = 2.0 V VCC = 3.0 V VCC = 4.5 V VCC = 6.0 V DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Test Conditions VCC V - 55 to 25_C v 85_C v 125_C Unit VIH Minimum High-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| v 20 mA 2.0 3.0 4.5 6.0 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 V VIL Maximum Low-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| v 20 mA 2.0 3.0 4.5 6.0 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 V VOH Minimum High-Level Output Voltage Vin = VIH or VIL |Iout| v 20 mA 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 3.0 4.5 6.0 2.48 3.98 5.48 2.34 3.84 5.34 2.20 3.70 5.20 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 6.0 0.26 0.26 0.26 0.33 0.33 0.33 0.40 0.40 0.40 Vin = VIH or VIL VOL Maximum Low-Level Output Voltage |Iout| v 2.4 mA |Iout| v 4.0 mA |Iout| v 5.2 mA Vin = VIH or VIL |Iout| v 20 mA Vin = VIH or VIL |Iout| v 2.4 mA |Iout| v 4.0 mA |Iout| v 5.2 mA http://onsemi.com 3 V MC74HC390A IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII IIII IIIIIIIII III IIII III IIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Test Conditions VCC V - 55 to 25_C v 85_C v 125_C Unit Iin Maximum Input Leakage Current Vin = VCC or GND 6.0 0.1 1.0 1.0 mA ICC Maximum Quiescent Supply Current (per Package) Vin = VCC or GND Iout = 0 mA 6.0 4 40 160 mA AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tf = tf = 6 ns) Guaranteed Limit VCC V - 55 to 25_C v 85_C v 125_C Unit fmax Maximum Clock Frequency (50% Duty Cycle) (Figures 1 and 3) 2.0 3.0 4.5 6.0 10 15 30 50 9 14 28 45 8 12 25 40 MHz tPLH, tPHL Maximum Propagation Delay, Clock A to QA (Figures 1 and 3) 2.0 3.0 4.5 6.0 70 40 24 20 80 45 30 26 90 50 36 31 ns tPLH, tPHL Maximum Propagation Delay, Clock A to QC (QA connected to Clock B) (Figures 1 and 3) 2.0 3.0 4.5 6.0 200 160 58 49 250 185 65 62 300 210 70 68 ns tPLH, tPHL Maximum Propagation Delay, Clock B to QB (Figures 1 and 3) 2.0 3.0 4.5 6.0 70 40 26 22 80 45 33 28 90 50 39 33 ns tPLH, tPHL Maximum Propagation Delay, Clock B to QC (Figures 1 and 3) 2.0 3.0 4.5 6.0 90 56 37 31 105 70 46 39 180 100 56 48 ns tPLH, tPHL Maximum Propagation Delay, Clock B to QD (Figures 1 and 3) 2.0 3.0 4.5 6.0 70 40 26 22 80 45 33 28 90 50 39 33 ns tPHL Maximum Propagation Delay, Reset to any Q (Figures 2 and 3) 2.0 3.0 4.5 6.0 80 48 30 26 95 65 38 33 110 75 44 39 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 3) 2.0 3.0 4.5 6.0 75 27 15 13 95 32 19 15 110 36 22 19 ns - 10 10 10 pF Symbol Cin Parameter Maximum Input Capacitance Typical @ 25C, VCC = 5.0 V CPD 35 Power Dissipation Capacitance (Per Counter)* * Used to determine the no-load dynamic power consumption: P D = CPD VCC 2 f + ICC VCC . http://onsemi.com 4 pF MC74HC390A IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIII IIIIIIIIII IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII IIIIIIII IIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIIIIII IIII IIII III IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII TIMING REQUIREMENTS (Input tr = tf = 6 ns) Guaranteed Limit Symbol Parameter VCC V - 55 to 25_C v 85_C v 125_C Unit trec Minimum Recovery Time, Reset Inactive to Clock A or Clock B (Figure 4) 2.0 3.0 4.5 6.0 25 15 10 9 30 20 13 11 40 30 15 13 ns tw Minimum Pulse Width, Clock A, Clock B (Figure 3) 2.0 3.0 4.5 6.0 75 27 15 13 95 32 19 15 110 36 22 19 ns tw Minimum Pulse Width, Reset (Figure 4) 2.0 3.0 4.5 6.0 75 27 20 18 95 32 24 22 110 36 30 28 ns Maximum Input Rise and Fall Times (Figure 3) 2.0 3.0 4.5 6.0 1000 800 500 400 1000 800 500 400 1000 800 500 400 ns tf, tf PIN DESCRIPTIONS INPUTS Clock A (Pins 1, 15) and Clock B (Pins 4, 15) OUTPUTS QA (Pins 3, 13) Clock A is the clock input to the / 2 counter; Clock B is the clock input to the / 5 counter. The internal flip-flops are toggled by high-to-low transitions of the clock input. Output of the / 2 counter. QB, QC, QD (Pins 5, 6, 7, 9, 10, 11) Outputs of the / 5 counter. QD is the most significant bit. QA is the least significant bit when the counter is connected for BCD output as in Figure 6. QB is the least significant bit when the counter is operating in the bi-quinary mode as in Figure 7. CONTROL INPUTS Reset (Pins 2, 14) Asynchronous reset. A high at the Reset input prevents counting, resets the internal flip-flops, and forces QA through QD low. SWITCHING WAVEFORMS CLOCK tf 90% 50% 10% 10% tr tw VCC VCC GND GND tw tPHL 1/fmax tPLH Q 50% RESET Q tPHL 90% 50% 10% 50% trec tTLH tTHL VCC 50% CLOCK GND Figure 3. Figure 4. http://onsemi.com 5 MC74HC390A TEST CIRCUIT TEST POINT OUTPUT DEVICE UNDER TEST CL* *Includes all probe and jig capacitance Figure 5. EXPANDED LOGIC DIAGRAM 1, 15 CLOCK A Q C D 4, 12 CLOCK B R R 5, 11 Q QB Q C D QA Q C D 3, 13 Q R Q 6, 10 Q C Q 7, 9 Q D C D R 2, 14 RESET TIMING DIAGRAM (QA Connected to Clock B) 0 1 2 3 4 5 6 7 8 9 CLOCK A RESET QA QB QC QD http://onsemi.com 6 0 1 2 3 4 5 6 MC74HC390A APPLICATIONS INFORMATION Each half of the MC54/74HC390A has independent / 2 and / 5 sections (except for the Reset function). The / 2 and / 5 counters can be connected to give BCD or bi-quinary (2-5) count sequences. If Output QA is connected to the Clock B input (Figure 4), a decade divider with BCD output is obtained. The function table for the BCD count sequence is given in Table 1. To obtain a bi-quinary count sequence, the input signals connected to the Clock B input, and output QD is connected to the Clock A input (Figure 7). QA provides a 50% duty cycle output. The bi-quinary count sequence function table is given in Table 2. Table 1. BCD Count Sequence* Table 2. Bi-Quinary Count Sequence** Output Count QD QC 0 L L 1 L L 2 L L 3 L L 4 L H 5 L H 6 L H 7 L H 8 H L 9 H L *QA connected to Clock B input. Output QB QA Count QA QD QC QB L L H H L L H H L L L H L H L H L H L H 0 1 2 3 4 8 9 10 11 12 L L L L L H H H H H L L L L H L L L L H L L H H L L L H H L L H L H L L H L H L ** QD connected to Clock A input. CONNECTION DIAGRAMS CLOCK A CLOCK B RESET 1, 15 /2 COUNTER 3, 13 /5 COUNTER 6, 10 5, 11 4, 12 7, 9 1, 15 QA CLOCK A QB CLOCK B 4, 12 QC QD /2 COUNTER /5 COUNTER 3, 13 QA 5, 11 QB 6, 10 7, 9 2, 14 2, 14 RESET Figure 6. BCD Count Figure 7. Bi-Quinary Count http://onsemi.com 7 QC QD MC74HC390A PACKAGE DIMENSIONS PDIP-16 CASE 648-08 ISSUE T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. -A- 16 9 1 8 B F C L S -T- H SEATING PLANE K G D M J 16 PL 0.25 (0.010) M T A M http://onsemi.com 8 DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 MC74HC390A PACKAGE DIMENSIONS SOIC-16 CASE 751B-05 ISSUE K -A- 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C -T- SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S SOLDERING FOOTPRINT* 8X 6.40 16X 1 1.12 16 16X 0.58 1.27 PITCH 8 9 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 9 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 MC74HC390A PACKAGE DIMENSIONS TSSOP-16 CASE 948F-01 ISSUE B 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U S V S K S EEE CCC CCC EEE K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. N 8 1 0.25 (0.010) M 0.15 (0.006) T U S A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. N F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E DIM A B C D F G H J J1 K K1 L M SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 10 MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC74HC390A ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 11 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74HC390A/D