NL17SZ04E Single Inverter The NL17SZ04E is an inverter in three tiny footprint packages. The device performs much as LCX multi-gate products in speed and drive. Features * * * * * * Tiny SOT-353 Package 24 mA Sink and Source Output Capability Over-Voltage Tolerant Inputs and Outputs Chip Complexity: FETs = 20 Designed for 1.65 V to 5.5 V VCC Operation These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant www.onsemi.com MARKING DIAGRAMS 5 L5 MG G 1 SOT-353/SC70-5/SC-88A DF SUFFIX CASE 419A VCC NC L5 M G 5 1 IN A = Specific Device Marking = Date Code* = Pb-Free Package (Note: Microdot may be in either location) 2 *Date Code orientation and/or position may vary depending upon manufacturing location. OUT Y GND 4 3 PIN ASSIGNMENT Figure 1. Pinout (Top View) 1 IN A OUT Y Figure 2. Logic Symbol Pin Function 1 NC 2 IN A 3 GND 4 OUT Y 5 VCC FUNCTION TABLE Input Output A Y L H H L ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. (c) Semiconductor Components Industries, LLC, 2017 September, 2018 - Rev. 1 1 Publication Order Number: NL17SZ04E/D NL17SZ04E MAXIMUM RATINGS Symbol Value Unit DC Supply Voltage -0.5 to +6.5 V VI DC Input Voltage -0.5 to +6.5 V VO DC Output Voltage -0.5 to VCC + 0.5 -0.5 to +6.5 V IIK DC Input Diode Current VI < GND -50 mA IOK DC Output Diode Current VO < GND -50 mA IO DC Output Sink Current 50 mA ICC DC Supply Current per Supply Pin 100 mA IGND DC Ground Current per Supply Pin 100 mA TSTG Storage Temperature Range -65 to )150 C 260 C )150 C 350 C/W 186 mW VCC Parameter Active Mode, High or Low State (Note 1) Power-Down Mode (VCC = 0 V) TL Lead Temperature, 1 mm from Case for 10 Seconds TJ Junction Temperature Under Bias qJA Thermal Resistance PD Power Dissipation in Still Air at 85C MSL Moisture Sensitivity FR Flammability Rating ESD ESD Classification ILATCHUP (Note 2) Level 1 Oxygen Index: 28 to 34 Human Body Model (Note 3) Charged Device Model (Note 4) Latchup Performance Above VCC and Below GND at 125C (Note 5) UL 94 V-0 @ 0.125 in 4000 1000 V 100 mA Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. IO absolute maximum rating must be observed. 2. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 3. Tested to EIA/JESD22-A114-A, rated to EIA/JESD22-A114-B. 4. Tested to JESD22-C101-A. 5. Tested to EIA/JESD78. www.onsemi.com 2 NL17SZ04E RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC DC Supply Voltage VIN DC Input Voltage Operating Data Retention Min Max Unit 1.65 1.5 5.5 5.5 V 0 5.5 V VOUT DC Output Voltage (High or Low State) (VCC = 0 V) 0 0 VCC 5.5 V VOUT DC Output Voltage (SOT-953 Package) (High or Low State) 0 VCC V -55 +125 C 0 0 0 20 10 5 ns/V TA Operating Temperature Range tr, tf Input Rise and Fall Time VCC = 2.5 V $ 0.2 V VCC = 3.0 V $ 0.3 V VCC = 5.0 V $ 0.5 V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. DC ELECTRICAL CHARACTERISTICS Symbol Parameter Condition Min 0.75 VCC 0.7 VCC VIH High-Level Input Voltage 1.65 to 1.95 2.3 to 5.5 VIL Low-Level Input Voltage 1.65 to 1.95 2.3 to 5.5 VOH High-Level Output Voltage VIN = VIL VOL IIN Low-Level Output Voltage VIN = VIH IOH = -100 mA -555C TA 1255C TA = 255C VCC (V) Typ Max Min Max 0.75 VCC 0.7 VCC 0.25 VCC 0.3 VCC V 0.25 VCC 0.3 VCC VCC - 0.1 VCC VCC - 0.1 IOH = -4 mA 1.65 1.29 1.52 1.29 IOH = -8 mA 2.3 1.9 2.1 1.9 IOH = -12 mA 2.7 2.2 2.4 2.2 IOH = -16 mA 3.0 2.4 2.7 2.4 IOH = -24 mA 3.0 2.3 2.5 2.3 IOH = -32 mA 4.5 3.8 4.0 IOL = 100 mA 1.65 to 5.5 0.0 0.1 0.1 IOH = 4 mA 1.65 0.08 0.24 0.24 IOL = 8 mA 2.3 0.20 0.3 0.3 IOL = 12 mA 2.7 0.22 0.4 0.4 IOL = 16 mA 3.0 0.28 0.4 0.4 IOL = 24 mA 3.0 0.38 0.55 0.55 IOL = 32 mA 4.5 0.42 0.55 0.55 $0.1 VIN = 5.5 V or GND 1.65 to 5.5 IOFF Power Off Leakage Current VIN = 5.5 V or VOUT = 5.5 V 0 ICC Quiescent Supply Current VIN = 5.5 V or GND 5.5 V V 1.65 to 5.5 Input Leakage Current Unit 3.8 V $1.0 mA 1 10 mA 1 10 mA Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 3 NL17SZ04E AC ELECTRICAL CHARACTERISTICS tR = tF = 2.5 ns -555C TA 1255C TA = 255C tPLH tPHL Condition VCC (V) Typ Max Max Unit RL = 1 MW, CL = 15 pF 1.65 1.8 5.3 4.4 11.4 9.5 12.0 10.0 ns RL = 1 MW, CL = 15 pF 2.5 $ 0.2 3.5 6.5 7.0 RL = 1 MW, CL = 15 pF 3.3 $ 0.3 2.1 4.5 4.7 2.9 5.5 5.2 1.8 3.9 4.1 2.4 4.3 4.5 Parameter Symbol Propagation Delay (Figure 3 and 4) Min RL = 500 W, CL = 50 pF 5.0 $ 0.5 RL = 1 MW, CL = 15 pF RL = 500 W, CL = 50 pF Min CAPACITIVE CHARACTERISTICS Symbol Parameter Condition CIN Input Capacitance VCC = 5.5 V, VI = 0 V or VCC CPD Power Dissipation Capacitance (Note 6) 10 MHz, VCC = 3.3 V, VI = 0 V or VCC 10 MHz, VCC = 5.5 V, VI = 0 V or VCC Typical Unit u2.5 pF 9 11 pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. tf = 3 ns tf = 3 ns 90% INPUT A and B VCC 90% 50% OUTPUT 50% 10% 10% tPHL GND CL tPLH VOH OUTPUT Y RL INPUT 50% A 1-MHz square input wave is recommended for propagation delay tests. 50% VOL Figure 3. Switching Waveform Figure 4. Test Circuit ORDERING INFORMATION Device NL17SZ04EDFT2G Package Shipping SC-88A/SOT-353/SC-70-5 (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. www.onsemi.com 4 NL17SZ04E PACKAGE DIMENSIONS SC-88A (SC-70-5/SOT-353) CASE 419A-02 ISSUE L A G 5 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. -B- S 1 2 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) B M M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 J C K H SOLDER FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 5 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NL17SZ04E/D