(978)927-1060 • FAX (978)922-6430 • www.deltarf.com 12
Assembly Procedures
Assembly Procedure A
1) Trim cable jacket to dimension A.
Slide backnut, washer, V-gasket, and
braid clamp onto cable as shown.
Cable jacket should bottom on step
in braid clamp.
2) Comb braid wires out straight and fold back over front
shoulder of braid clamp (braid wires should not overlap
one another after folding). Trim braid wires flush with step
of braid clamp. Trim cable dielectric and center conductor
to dimensions B and C.
3) If support insulator is provided for RG-62 or 71 cable, insert
into hollow in dielectric. Assemble rear bushing or washer (if
supplied), rear insulator (if captive contact) and contact, and
solder contact to center conductor. Rear of contact should be
flush with cable dielectric end. For right angle connectors
with access cap, omit this step entirely.
4) Insert prepared cable and hardware into body
and tighten backnut. For right angle connectors
with access cap, solder center conductor into slot
in contact and tighten access cap.
Code A B C
A/01 .375 (3/8) .047 (3/64) .203 (13/64)
A/02 .375 (3/8) .109 (7/64) .203 (13/64)
A/03 .438 (7/16) .250 (1/4) .188 (3/16)
A/04 .281 (9/32) .047 (3/64) .125 (1/8)
A/05 .313 (5/16) .125 (1/8) .109 (7/64)
A/06 .594 (19/32) .391 (25/64) .156 (5/32)
A/07 .375 (3/8) .047 (3/64) .125 (1/8)
A/08 .281 (9/32) .109 (7/64) .094 (3/32)
A/09 .344 (11/32) .109 (7/64) .094 (3/32)
A/10 .406 (13/32) .109 (7/64) .203 (13/64)
A/11 .500 (1/2) .281 (9/32) .156 (5/32)
A/12 .343 .040 .219
A/13 .375 (3/8) .125 (1/8) .156 (5/32)
A/14 .355 .090 .188 (3/16)
A/15 .425 .094 (3/32) .259
A/16 .328 (21/64) .094 (3/32) .188 (3/16)
A/17 .375 (3/8) .109 (7/64) .125 (1/8)
A/18 .375 (3/8) .062 (1/16) .172 (11/64)
A/19 .375 (3/8) .188 (3/16) .094 (3/32)
Code A B C
A/20 .375 (3/8) .047 (3/64) .172 (11/64)
A/21 .500 (1/2) .313 (5/16) .172 (11/64)
A/22 .375 (3/8) .188 (3/16) .141 (9/64)
A/23 .438 (7/16) .078 (5/64) .172 (11/64)
A/24 .500 (1/2) .094 (3/32) .141 (9/64)
A/25 .438 (7/16) .141 (9/64) .172 (11/64)
A/26 .625 (5/8) .281 (9/32) .250 (1/4)
A/27 .688 (11/16) .281 (9/32) .125 (1/8)
A/28 .656 (21/32) .297 (19/64) .250 (1/4)
A/29 .688 (11/16) .125 (1/8) .313 (5/16)
A/30 .688 (11/16) .469 (15/32) .156 (5/32)
A/31 .700 (21/32) .453 (29/64) .250 (1/4)
A/32 .313 (5/16) .078 (5/64) .188 (3/16)
A/33 .250 (1/4) .078 (5/64) .094 (3/32)
A/34 .250 (1/4) .062 (1/16) .109 (7/64)
A/35 .837 .575 .150
A/36 .450 .250 .150
A/37 .281 .038 .188
A/38 .281 .069 .156
Trim Codes For Assembly Procedure A