HCPL-2530, HCPL-2531, HCPL-4534 HCPL-0530, HCPL-0531, HCPL-0534 Dual Channel, High Speed Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features These dual channel optocouplers contain a pair of light emitting diodes and integrated photo-detectors with electrical insulation between input and output. Separate connection for the photodiode bias and output transistor collectors increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance. These dual channel optocouplers are available in an 8 Pin DIP and in an industry standard SO-8 package. The following is a cross reference table listing the 8 Pin DIP part number and the electrically equivalent SO-8 part number. 8 Pin DIP SO-8 Package HCPL-2530 HCPL-0530 HCPL-2531 HCPL-0531 HCPL-4534 HCPL-0534 Functional Diagram x 15 kV/Ps minimum common mode transient immunity at VCM = 1500 V (HCPL-4534/0534) x TTL compatible x Available in 8 pin DIP, SO-8, and 8 pin DIP - gull wing surface mount (option 020) packages x High density packaging x 3 MHz bandwidth x Open collector outputs x Safety approval UL Recognized - 3750 V rms for 1 minute (5000 V rms for 1 minute for Option 020) per UL1577 CSA Approved IEC/EN/DIN EN 60747-5-2 - VIORM = 630 Vpeak for HCPL-2530/2531/4534 0ption 060 - VIORM = 560 Vpeak for HCPL-0530/0531/0534 0ption 060 x Single channel version available (4502/3, 0452/3) x MIL-PRF-38534 hermetic version available (55XX/65XX/4N55) Applications ANODE 1 1 8 VCC CATHODE 1 2 7 VO1 CATHODE 2 3 6 VO2 ANODE 2 4 5 GND A 0.1 PF bypass capacitor between pins 5 and 8 is recommended. TRUTH TABLE (POSITIVE LOGIC) LED VO LOW ON HIGH OFF x Line receivers - high common mode transient immunity (>1000 V/Ps) and low input-output capacitance (0.6 pF) x High speed logic ground isolation - TTL/TTL, TTL/LTTL, TTL/CMOS, TTL/LSTTL x Replace pulse transformers - save board space and weight x Analog signal ground isolation - integrated photon detector provides improved linearity over phototransistor type x Polarity sensing x Isolated analog amplifier - dual channel packaging enhances thermal tracking CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The SO-8 does not require "through holes" in a PCB. This package occupies approximately one-third the footprint area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface mount processes. The HCPL-2531/0531 is designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough output current for 1 TTL load and a 5.6 k: pull-up resistor. CTR of the HCPL2531/0531 is 19% minimum at IF = 16 mA. The HCPL-2530/0530 is for use in TTL/CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for the HCPL-2530/0530 is 7% minimum at IF = 16 mA. The HCPL-4534/0534 is an HCPL-2531/0531 with increased common mode transient immunity of 15,000 V/s minimum at VCM = 1500 V guaranteed. Selection Guide Minimum CMR 8-pin DIP (300 Mil) Widebody (400 Mil) Hermetic Single and Dual Channel Packages* dV/dt (V/s) VCM (V) Current Transfer Ratio (%) Dual Channel Package Single Channel Package* Dual Channel Package Single Channel Package* Single Channel Package* 1,000 10 7 HCPL-2530 6N135 HCPL-0530 HCPL-0500 HCNW135 19 HCPL-2531 6N136 HCPL-4502 HCPL-0531 HCPL-0501 HCPL-0452 HCNW136 HCNW4502 HCPL-4534 HCPL-4503 HCPL-0534 HCPL-0453 HCNW4503 15,000 1500 19 1,000 10 9 * Technical data for these products are on separate Avago publications. 2 Small-Outline SO-8 HCPL-55XX HCPL-65XX 4N55 Ordering Information HCPL-2530, HCPL-2531, HCPL-4534, HCPL-0530, HCPL-0531 and HCPL-0534 are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA Component Acceptance Notice #5, File CA 88324. Option Part number HCPL-2530 HCPL-2531 HCPL-4534 HCPL-0530 HCPL-0531 HCPL-0534 RoHS Compliant Non RoHS Compliant -000E No option -300E -300 X X -500E -500 X X -020E -020 -320E -320 -520E -520 -060E -060 -360E -360 X X -560E -560 X X -000E No option -500E -500 Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute rating IEC/EN/DIN EN 60747-5-2 Quantity 50 per tube 300mil DIP-x X X X X 50 per tube X X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel 100 per tube SO-8 X X X 1500 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-2530-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-2530 to order product of 300mil DIP package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Remarks: The notation `#XXX' is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use `-XXXE`. 3 Schematic 1 ICC I F1 + 8 VF1 I O1 - 7 VCC VO1 2 3 I F2 - I O2 6 VF2 VO2 + 4 GND 5 HCPL-4534/0534 SHIELD USE OF A 0.1 F BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED. Package Outline Drawings 8-Pin DIP Package (HCPL-2530/2531/4534) 7.62 0.25 (0.300 0.010) 9.65 0.25 (0.380 0.010) TYPE NUMBER 8 7 6 5 OPTION CODE* 6.35 0.25 (0.250 0.010) DATE CODE A XXXXZ YYWW RU 1 1.19 (0.047) MAX. 2 3 4 UL RECOGNITION 1.78 (0.070) MAX. 5 TYP. 3.56 0.13 (0.140 0.005) 4.70 (0.185) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 0.320 (0.043 0.013) 4 0.65 (0.025) MAX. 2.54 0.25 (0.100 0.010) DIMENSIONS IN MILLIMETERS AND (INCHES). *MARKING CODE LETTER FOR OPTION NUMBERS. "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Package Outline Drawings, continued 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2530/2531/4534) LAND PATTERN RECOMMENDATION 9.65 0.25 (0.380 0.010) 6 7 8 1.016 (0.040) 5 6.350 0.25 (0.250 0.010) 1 3 2 10.9 (0.430) 4 2.0 (0.080) 1.27 (0.050) 9.65 0.25 (0.380 0.010) 1.780 (0.070) MAX. 1.19 (0.047) MAX. 7.62 0.25 (0.300 0.010) + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 3.56 0.13 (0.140 0.005) 1.080 0.320 (0.043 0.013) 0.635 0.25 (0.025 0.010) 12 NOM. 0.635 0.130 2.54 (0.025 0.005) (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Small Outline SO-8 Package (HCPL-0530/0531/0534) LAND PATTERN RECOMMENDATION 8 7 6 5 5.994 0.203 (0.236 0.008) XXX YWW 3.937 0.127 (0.155 0.005) TYPE NUMBER (LAST 3 DIGITS) 7.49 (0.295) DATE CODE 1 2 3 0.406 0.076 (0.016 0.003) 4 1.9 (0.075) 1.270 BSC (0.050) 7 * 5.080 0.127 (0.200 0.005) 3.175 0.127 (0.125 0.005) 0.64 (0.025) 45 X 0.432 (0.017) 0.228 0.025 (0.009 0.001) 1.524 (0.060) 0.203 0.102 (0.008 0.004) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 0.254 (0.205 0.010) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 5 0.305 MIN. (0.012) NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. Solder Reflow Thermal Profile 300 PREHEATING RATE 3 C + 1 C/-0.5 C/SEC. REFLOW HEATING RATE 2.5 C 0.5 C/SEC. 200 PEAK TEMP. 245 C PEAK TEMP. 240 C TEMPERATURE (C) 2.5 C 0.5 C/SEC. 30 SEC. 160 C 150 C 140 C PEAK TEMP. 230 C SOLDERING TIME 200 C 30 SEC. 3 C + 1 C/-0.5 C 100 PREHEATING TIME 150 C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 200 250 TIME (SECONDS) NOTE: NON-HALIDE FLUX SHOULD BE USED. Recommended Pb-Free IR Profile tp Tp TEMPERATURE TL Tsmax TIME WITHIN 5 C of ACTUAL PEAK TEMPERATURE 15 SEC. * 260 +0/-5 C 217 C 150 - 200 C RAMP-UP 3 C/SEC. MAX. RAMP-DOWN 6 C/SEC. MAX. Tsmin NOTES: THE TIME FROM 25 C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 C, Tsmin = 150 C NOTE: NON-HALIDE FLUX SHOULD BE USED. ts PREHEAT 60 to 180 SEC. tL 60 to 150 SEC. * RECOMMENDED PEAK TEMPERATURE FOR WIDEBODY 400mils PACKAGE IS 245 C 25 t 25 C to PEAK TIME Regulatory Information The devices contained in this data sheet have been approved by the following organizations: UL IEC/EN/DIN EN 60747-5-2 Recognized under UL 1577, Component Recognition Program, File E55361. Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01. (Option 060 only) CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. 6 Insulation and Safety Related Specifications Parameter Symbol 8-Pin DIP (300 Mil) Value Minimum External Air Gap (External Clearance) L(101) 7.1 4.9 mm Measured from input terminals to output to to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 7.4 4.8 mm Measured from input terminals to output terminals, shortest distance path along body. Minimum Internal Plastic Gap (Internal Clearance) 0.08 0.08 mm Through insulation distance, conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal Tracking (Internal Creepage) NA NA mm Measured from input terminals to output terminals, along internal cavity. 200 200 Volts DIN IEC 112/VDE 0303 Part 1 IIIa IIIa Tracking Resistance (Comparative Tracking Index) Isolation Group CTI SO-8 Value Units Conditions Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. 7 IEC/EN/DIN EN 60747-5-2 Insulation Characteristics (Option 060) Characteristic HCPL2530/2531/4534 HCPL0530/0531/0534 Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage 150 V rms for rated mains voltage 300 V rms for rated mains voltage 600 V rms I-IV I-III I-IV I-III I-II Climatic Classification 55/100/21 55/100/21 Description Symbol Pollution Degree (DIN VDE 0110/1.89) Unit 2 2 Maximum Working Insulation Voltage VIORM 630 567 Vpeak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC VPR 1181 1050 Vpeak Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and Sample Test, tm = 60 sec, Partial Discharge < 5 pC VPR 945 840 Vpeak VIOTM 6000 4000 Vpeak Safety Limiting Values (Maximum values allowed in the event of a failure.) Case Temperature Input Current** Output Power** TS IS,INPUT PS,OUTPUT 175 230 600 150 230 600 C mA mW Insulation Resistance at TS, VIO = 500 V RS > 109 > 109 : Highest Allowable Overvoltage (Transient Overvoltage, tini = 10 sec) * Refer to the optocoupler section of the Isolation and Control Components Designer's Catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test profiles. ** Refer to the following figure for dependence of PS and IS on ambient temperature. OUTPUT POWER - PS, INPUT CURRENT - IS Note: Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application. 800 PS (mW) IS (mA) 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 200 TS - CASE TEMPERATURE - C 8 Absolute Maximum Ratings Parameter Symbol Storage Temperature Min. Max. Units TS -55 125 C Operating Temperature TA -55 100 C Average Forward Input Current (each channel) IF(AVG) 25 mA Peak Forward Input Current (each channel) (50% duty cycle, 1 ms pulse width) IF(PEAK) 50 mA Peak Transient Input Current (each channel) ( 1 s pulse width, 300 pps) IF(TRANS) 1 A Reverse LED Input Voltage (each channel) VR 5 V Input Power Dissipation (each channel) PIN 45 mW Average Output Current (each channel) IO(AVG) 8 mA Peak Output Current IO(PEAK) 16 mA Supply Voltage (Pin 8-5) VCC -0.5 30 V Output Voltage (Pins 7-5, 6-5) VO -0.5 20 V Output Power Dissipation (each channel) PO 35 mW Lead Solder Temperature (Through-Hole Parts Only) 1.6 mm below seating plane, 10 seconds TLS 8 Pin DIP 260 C Reflow Temperature Profile TRP SO-8 and Option 300 9 Device see Package Outline Drawings section Note 13 Electrical Specifications (DC) Over recommended temperature (TA = 0C to 70C) unless otherwise specified. See note 9. Parameter Sym. Device Min. Typ.* Max. Units Current Transfer Ratio CTR HCPL-2530/ 0530 7 18 50 % TA = 25C 24 50 % TA = 25C 0.1 0.5 V 5 HCPL-2531/ 0531 HCPL-4534/ 0534 Logic Low Output Voltage VOL 19 HCPL-2530/ 0530 TA = 25C 0.5 0.1 0.5 V TA = 25C 1, 2 IF = 16 mA, VCC = 4.5 V 1 1 0.003 0.5 6 1 3 1 IO = 3.0 mA IO = 2.4 mA 0.5 IOH IO = 1.1 mA A TA = 25C VCC = VO = 5.5V, IF = 0 mA IF = 0 mA TA = 25C VCC = VO = 15V, IF = 0 mA Logic Low Supply Current ICCL 100 400 A IF = 16 mA, VO = Open, VCC = 15 V Logic High Supply Current ICCH 0.05 4 A IF = 0 mA, VO = Open, VCC = 15 V VF 1.5 1.7 V TA = 25C IF = 16 mA 1.8 Input Reverse Breakdown Voltage BVR Temperature Coefficient of Forward Voltage VF TA -1.6 mV/ C Input Capacitance CIN 60 pF *All typicals at TA = 25C. 10 Note 1, 2 4 IO = 0.8 mA 50 Input Forward Voltage Fig. IF = 16 mA, VCC = 4.5 V VO = 0.5 V 15 HCPL-2531/ 0531 HCPL-4534/ 0534 Logic High Output Current Test Conditions 5 V IR =10 A 1 IF = 16 mA f = 1 MHz, VF = 0 V 1 Switching Specifications (AC) Over recommended temperature (TA = 0C to 70C), VCC = 5 V, IF = 16 mA unless otherwise specified. Parameter Sym. Device HCPL- Propagation Delay Time to Logic Low at Output tPHL Propagation Delay Time High to Logic at Output tPLH Min. Typ.* Max. Units 2530/0530 0.2 Ps 2531/0531/ 4534/0534 0.2 1.5 2.0 0.8 1.0 2530/0530 1.3 Ps 2531/0531/ 4534/0534 0.6 1.5 2.0 0.8 1.0 Test Conditions TA = 25C RL = 4.1 k: TA = 25C RL = 1.9 k: TA = 25C RL = 4.1 k: TA = 25C RL = 1.9 k: Fig. Note 5, 9, 11 6, 7 5, 9, 11 6, 7 Common Mode Transient Immunity at Logic High Level Output |CMH| 2530/0530 2531/0531 4534/0534 1 1 15 10 10 30 kV/Ps RL = 4.1 k: RL = 1.9 k: RL = 1.9 k: IF = 0 mA, TA = 25C, VCM = 10 Vp-p 10 5, 6, 7 Common Mode Transient Immunity at Logic Low Level Output |CML| 2530/0530 2531/0531 4534/0534 1 1 15 10 10 30 kV/Ps RL = 4.1 k: RL = 1.9 k: RL = 1.9 k: IF = 0 mA, TA = 25C, VCM = 10 Vp-p 10 5, 6, 7 3 MHz RL = 100 k: Bandwidth BW 7, 8 *All typicals at TA = 25C. Package Characteristics Parameter Sym. Device Min. Typ.* 3750 HCPL-2530/2531 5000 /4534 Option 020 Max. Units Test Conditions V rms RH < 50%, t = 1 min., Fig. Note Input-Output Momentary Withstand Voltage** VISO 3, 10 3, 11 Resistance (Input-Output) RI-O 1012 : RH 45% VI-O = 500 Vdc, t=5s 3 Capacitance (Input-Output) CI-O 0.6 pF f = 1 MHz, TA = 25C 12 Input-Input Insulation Leakage Current II-I 0.005 PA RH 45%, t = 5 s, VI-I = 500 Vdc 4 Resistance (Input-Input) RI-I 1011 : Capacitance (Input-Input) CI-I HCPL-2530/ 2531/4534 0.03 pF HCPL-0530/ 0531/0534 0.25 4 f = 1 MHz 4 *All typicals at TA = 25C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage," publication number 5963-2203E. 11 30 mA 25 mA 5 20 mA 15 mA 10 mA IF = 5 mA 0 0 20 10 1000 HCPL-2530/0530 HCPL-2531/0531/4534/0534 1.0 0.5 NORMALIZED I F = 16 mA VO = 0.5 V VCC = 5 V TA = 25C 0.1 0 VO - OUTPUT VOLTAGE - V 1.0 0.9 NORMALIZED IF = 16 mA VO = 0.5 V VCC = 5 V TA = 25C HCPL-2530/0530 HCPL-2531/0531/4534/0534 0.6 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE - C Figure 4. Current transfer ratio vs. temperature. 12 tP - PROPAGATION DELAY - ns NORMALIZED CURRENT TRANSFER RATIO 2000 1500 1000 t PHL 500 0 -60 -20 20 60 TA - TEMPERATURE - C Figure 5. Propagation delay vs. temperature. TA = 25C + VF - 10 1.0 0.1 0.01 1.2 1.3 1.4 1.5 1.6 VF - FORWARD VOLTAGE - VOLTS IF = 16 mA, VCC = 5.0 V HCPL-2530/0530 (RL = 4.1 k) HCPL-2531/0531/4534/0534 (RL = 1.9 k) t PLH IF 0.001 1.1 100 Figure 2. Current transfer ratio vs. input current. 1.1 0.7 10 100 IF - INPUT CURRENT - mA Figure 1. DC and pulsed transfer characteristics. 0.8 1 100 Figure 3. Input current vs. forward voltage. IOH - LOGIC HIGH OUTPUT CURRENT - nA IO - OUTPUT CURRENT - mA 35 mA 1.5 IF - FORWARD CURRENT - mA 40 mA TA = 25C 10 VCC = 5.0 V NORMALIZED CURRENT TRANSFER RATIO Notes: 1. Each channel. 2. CURRENT TRANSFER RATIO is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%. 3. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together. 4. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. 5. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the rising edge of the common mode pulse, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dVCM /dt on the falling edge of the common mode pulse signal, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V). 6. The 1.9 k: load represents 1 TTL unit load of 1.6 mA and the 5.6 k pull-up resistor. 7. The 4.1 k: load represents 1 LSTTL unit load of 0.36 mA and the 6.1 k pull-up resistor. 8. The frequency at which the ac output voltage is 3 dB below the low frequency asymptote. 9. Use of a 0.1 PF bypass capacitor connected between pins 5 and 8 is recommended. 10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 4500 V rms for 1 second (leakage detection current limit, II-O 5 PA). 11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 6000 V rms for 1 second (leakage detection current limit, II-O 5 PA). 12. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. 13. Derate linearly above 90C free-air temperature at a rate of 3.0 mW/ C for the SOIC-8 package. 10+4 10+3 IF = 0 VO = VCC = 5.0 V 10+2 10+1 10 0 10 -1 10 -2 -50 -25 0 +25 +50 +75 +100 TA - TEMPERATURE - C Figure 6. Logic high output current vs. temperature. IO I F - SMALL SIGNAL CURRENT TRANSFER RATIO 0.30 TA = 25C, RL = 100 , VCC = 5 V 0.20 0.10 0 0 4 8 12 20 16 24 IF - QUIESCENT INPUT CURRENT - mA Figure 7. Small-signal current transfer ratio vs. quiescent input current. NORMALIZED RESPONSE -dB 0 -5 TA = 25 C IF = 16 mA -10 -15 +5 V SET I F RL = 100 RL = 220 RL = 470 RL = 1 k 20 k AC INPUT 1 8 2 7 3 6 +5 V RL 2N3053 0.1 F 560 100 4 -20 VO 0.1 F 5 -25 -30 0.01 1.6 V dc 0.25 Vp-p ac 0.1 1.0 10 f - FREQUENCY - MHz Figure 8. Frequency response. PULSE GEN. Z O = 50 t r = 5 ns IF 0 5V VO 1.5 V Figure 9. Switching test circuit. 13 t PLH 1 8 2 7 3 6 10% DUTY CYCLE 1/f < 100 s 1.5 V VOL t PHL IF +5 V RL VO 0.1F I F MONITOR 4 RM 5 CL = 1.5 pF B IF 1 8 2 7 3 6 4 5 +5 V A VCM 0V 10% 90% 90% RL 10% tr V FF tf VO 5V VO 0.1 F SWITCH AT A: I F = 0 mA VO SWITCH AT B: I F = 16 mA VOL VCM + - PULSE GEN. Figure 10. Test circuit for transient immunity and typical waveforms tP - PROPAGATION DELAY - s 3.0 2.0 I F = 10 mA I F = 16 mA VCC = 5.0 V TA = 25 C 1.0 0.8 0.6 tPLH 0.4 t PHL 0.2 0.1 1 2 3 4 5 6 7 8 9 10 RL - LOAD RESISTANCE - k Figure 11. Propagation delay time vs. load resistance For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2011 Avago Technologies. All rights reserved. Obsoletes AV01-0370EN AV02-2333EN - February 21, 2011