ADC0816, ADC0817 www.ti.com SNAS527C - JUNE 1999 - REVISED MARCH 2013 ADC0816/ADC0817 8-Bit P Compatible A/D Converters with16-Channel Multiplexer Check for Samples: ADC0816, ADC0817 FEATURES 1 * * 23 * * * * * * * * * * Easy interface to all microprocessors Operates ratiometrically or with 5 VDC or analog span adjusted voltage reference 16-channel multiplexer with latched control logic Outputs meet TTL voltage level specifications 0V to 5V analog input voltage range with single 5V supply No zero or full-scale adjust required Standard hermetic or molded 40-pin MDIP package Temperature range -40C to +85Cor -55C to +125C Latched TRI-STATE output Direct access to "comparator in" and "multiplexer out" for signal conditioning ADC0816 equivalent to MM74C948 ADC0817 equivalent to MM74C948-1 KEY SPECIFICATIONS * * * * * Resolution ........................8 Bits Total Unadjusted Error....1/2 LSB and 1 Single Supply....................5 VDC Low Power........................15 mW Conversion Time..............100 s DESCRIPTION The ADC0816, ADC0817 data acquisition component is a monolithic CMOS device with an 8-bit analog-todigital converter,16-channel multiplexer and microprocessor compatible control logic. The 8-bit A/D converter uses successive approximation as the conversion technique. The converter features a high impedance chopper stabilized comparator, a 256R voltage divider with analog switch tree and a successive approximation register. The 16-channel multiplexer can directly access any one of 16-singleended analog signals, and provides the logic for additional channel expansion. Signal conditioning of any analog input signal is eased by direct access to the multiplexer output, and to the input of the 8-bit A/D converter. The device eliminates the need for external zero and full-scale adjustments. Easy interfacing to microprocessors is provided by the latched and decoded multiplexer address inputs and latched TTL TRI-STATE(R)outputs. The design of the ADC0816, ADC0817 has been optimized by incorporating the most desirable aspects of several A/D conversion techniques. The ADC0816,ADC0817 offers high speed, high accuracy, minimal temperature dependence, excellent long-term accuracy and repeatability, and consumes minima lpower. These features make this device ideally suited to applications from process and machine control to consumer and automotive applications. For similar performance in an 8-channel, 28-pin, 8-bit A/D converter, see the ADC0808, ADC0809 data sheet. (See AN-258 for more information.) 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. TRI-STATE is a registered trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated ADC0816, ADC0817 SNAS527C - JUNE 1999 - REVISED MARCH 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Block Diagram Connection Diagram Dual-In-Line Package See Package Number NJF0040A 2 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 ADC0816, ADC0817 www.ti.com SNAS527C - JUNE 1999 - REVISED MARCH 2013 Absolute Maximum Ratings Supply Voltage (VCC) (1) (2) (3) 6.5V -0.3V to (VCC+0.3V) Voltage at Any Pin Except Control Inputs -0.3V to 15V Voltage at Control Inputs (START, OE, CLOCK, ALE, EXPANSION CONTROL, ADD A, ADD B, ADD C, ADD D) -65C to +150C Storage Temperature Range Package Dissipation at TA = 25C 875 mW Lead Temp. (Soldering, 10 seconds) Dual-In-Line Package (Plastic) 260C Molded Chip Carrier Package Vapor Phase (60seconds) 215C Infrared (15 seconds) 220C ESD Susceptibility (1) (2) (3) (4) (4) 400V Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. All voltages are measured with respect to GND, unless otherwise specified. A Zener diode exists, internally, from VCC to GND and has a typical breakdown voltage of 7 VDC. Human body model, 100 pF discharged through a 1.5 k resistor. Operating Conditions Temperature Range (1) (2) TMINTATMAX -40CTA+85C ADC0816CCN, ADC0817CCN Range of VCC (2) 4.5 VDC to 6.0VDC Voltage at Any Pin 0V to VCC Except Control Inputs Voltage at Control Inputs 0V to 15V (START,OE, CLOCK, ALE, EXPANSION CONTROL, ADD A, ADD B, ADD C, ADDD) (1) (2) All voltages are measured with respect to GND, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 Submit Documentation Feedback 3 ADC0816, ADC0817 SNAS527C - JUNE 1999 - REVISED MARCH 2013 www.ti.com Electrical Characteristics Converter Specifications: VCC = 5 VDC = VREF(+), VREF(-)= GND, VIN = VCOMPARATOR IN,TMIN TMAX and fCLK = 640 kHz unless otherwise stated. Symbol Parameter Conditions Min Typ Max Units ADC0816 Total Unadjusted Error 25C 1/2 LSB (1) TMIN to TMAX 3/4 LSB Total Unadjusted Error 0C to 70C 1 LSB (1) TMIN to TMAX 11/4 LSB VCC + 0.1 VDC VCC VCC+0.1 V VCC/2 VCC/2 + 0.1 See Note ADC0817 See Note VREF(+) Input Resistance From Ref(+)to Ref(-) Analog Input Voltage Range V(+) or V(-) Voltage, Top of Ladder Measured at Ref(+) 1.0 (2) GND - 0.1 VCC/2 - 0.1 Voltage, Center of Ladder VREF(-) (1) (2) (3) 4 Voltage, Bottom of Ladder Measured at Ref(-) Comparator Input Current fc = 640 kHz, 4.5 (3) -0.1 0 -2 0.5 k V V 2 A Total unadjusted error includes offset, full-scale, and linearity errors. See Figure 3. None of these A/Ds requires a zero or full-scale adjust. However, if an all zero code is desired for an analog input other than 0.0V,or if a narrow full-scale span exists (for example: 0.5V to 4.5V full-scale)the reference voltages can be adjusted to achieve this. See Figure 13. Two on-chip diodes are tied to each analog input which will forward conduct for analog input voltages one diode drop below ground or one diode drop greater than the VCCsupply. The spec allows 100 mV forward bias of either diode. This means that as long as the analog VIN does not exceed the supply voltage by more than 100 mV, the output code will be correct. To achieve an absolute0 VDC to 5 VDC input voltage range will therefore require a minimum supply voltage of 4.900 VDC over temperature variations, initial tolerance and loading. Comparator input current is a bias current into or out of the chopper stabilized comparator. The bias current varies directly with clock frequency and has little temperature dependence (Figure 6). Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 ADC0816, ADC0817 www.ti.com SNAS527C - JUNE 1999 - REVISED MARCH 2013 Electrical Characteristics Digital Levels and DC Specifications: ADC0816CCN, ADC0817CCN--4.75V VCC 5.25V, -40C TA +85C unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units 1.5 ANALOG MULTIPLEXER (Any Selected Channel) RON RON Analog Multiplexer ON Resistance ON Resistance Between Any 2 Channels TA = 25C, RL= 10k 3 k TA = 85C 6 k TA = 125C 9 k (Any Selected Channel) RL=10k 75 VCC= 5V, VIN= 5V, IOFF+ OFF Channel Leakage Current TA = 25C 10 TMIN to TMAX 200 nA 1.0 A VCC = 5V, VIN = 0, IOFF(-) OFF Channel Leakage Current TA = 25C -200 nA TMIN to TMax -1.0 A VCC - 1.5 V CONTROL INPUTS VIN(1) Logical "1"Input Voltage VIN(0) Logical "0"Input Voltage IIN(1) Logical "1"Input Current (The Control Inputs) VIN = 15V IIN(0) Logical "0"Input Current (The Control Inputs) VIN = 0 ICC Supply Current fCLK = 640 kHz 1.5 V 1.0 A -1.0 A 0.3 3.0 mA DATA OUTPUTS AND EOC (INTERRUPT) VOUT(1) Logical "1"Output Voltage IO = -360 A, TA = 85C IO = -300 A, TA = 125C VOUT(0) Logical "0"Output Voltage IO = 1.6 mA 0.45 VOUT(0) Logical "0"Output Voltage EOC IO = 1.2 mA 0.45 V VO = VCC 3.0 A IOUT TRI-STATE Output Current VCC - 0.4 VO = 0 Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 -3.0 V V A Submit Documentation Feedback 5 ADC0816, ADC0817 SNAS527C - JUNE 1999 - REVISED MARCH 2013 www.ti.com Electrical Characteristics Timing Specifications:VCC = VREF(+) = 5V, VREF(-) = GND, tr = tf = 20 ns and TA = 25C unless otherwise noted. Symbol Parameter Conditions Min (1) Typ Max Units tWS Minimum Start Pulse Width (Figure 5) 100 200 ns tWALE Minimum ALE Pulse Width (Figure 5) 100 200 ns ts Minimum Address Set-Up Time (Figure 5) 25 50 ns TH Minimum Address Hold Time (Figure 5) 25 50 ns tD Analog MUX Delay Time from ALE RS= O (Figure 5) 1 2.5 s tH1, tH0 OE Control to Q Logic State CL= 50 pF, RL= 10k (Figure 8) 125 250 ns t1H, t0H OE Control to Hi-Z CL= 10 pF, RL= 10k (Figure 8) tC Conversion Time fc=640 kHz, (Figure 5) fc Clock Frequency tEOC EOC Delay Time (Figure 5) CIN Input Capacitance At Control Inputs COUT TRI-STATE Output Capacitance At TRI-STATE Outputs (1) (2) (2) 125 250 ns 90 100 116 s 10 640 1280 kHz 8 + 2s Clock Periods 10 15 pF 10 15 pF 0 (2) If start pulse is asynchronous with converter clock or if fc > 640 kHz, the minimum start pulse width is 8clock periods plus 2 s. For synchronous operation at fc 640 kHz take start high within 100 ns of clock going low. The outputs of the data register are updated one clock cycle before the rising edge of EOC. Functional Description Multiplexer: The device contains a 16-channel single-ended analog signal multiplexer. A particular input channel is selected by using the address decoder. Table 1 shows the input states for the address line and the expansion control line to select any channel. The address is latched into the decoder on the low-to-high transition of the address latch enable signal. Table 1. Inputs States for the Address line Address Line (1) Selected AnalogChannel (1) 6 Expansion D C B A Control IN0 L L L L H IN1 L L L H H IN2 L L H L H IN3 L L H H H IN4 L H L L H IN5 L H L H H IN6 L H H L H IN7 L H H H H IN8 H L L L H IN9 H L L H H IN10 H L H L H IN11 H L H H H IN12 H H L L H IN13 H H L H H IN14 H H H L H IN15 H H H H H All Channels OFF X X X X L X = don't care Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 ADC0816, ADC0817 www.ti.com SNAS527C - JUNE 1999 - REVISED MARCH 2013 Additional single-ended analog signals can be multiplexed to the A/D converter by disabling all the multiplexer inputs using the expansion control. The additional external signals are connected to the comparator input and the device ground. Additional signal conditioning (i.e., prescaling, sample and hold, instrumentation amplification, etc.) may also be added between the analog input signal and the comparator input. CONVERTER CHARACTERISTICS The Converter The heart of this single chip data acquisition system is its8-bit analog-to-digital converter. The converter is designed to give fast, accurate, and repeatable conversions over a wide range of temperatures. The converter is partitioned into 3 major sections: the 256R ladder network, the successive approximation register, and the comparator. The converter's digital outputs are positive true. The 256R ladder network approach Figure 1 was chosen over the conventional R/2R ladder because of its inherent monotonicity, which specifies no missing digital codes. Monotonicity is particularly important in closed loop feedback control systems. A non-monotonic relationship can cause oscillations that will be catastrophic for the system. Additionally, the 256R network does not cause load variations on the reference voltage. The bottom resistor and the top resistor of the ladder networking Figure 1 are not the same value as the remainder of the network. The difference in these resistors causes the output characteristic to be symmetrical with the zero and full-scale points of the transfer curve. The first output transition occurs when the analog signal has reached + 1/2 LSB and succeeding output transitions occur every 1 LSB later up to full-scale. Figure 1. Resistor Ladder and Switch Tree Figure 2. 3-Bit A/D Transfer Curve Figure 3. 3-Bit A/D Absolute Accuracy Curve Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 Submit Documentation Feedback 7 ADC0816, ADC0817 SNAS527C - JUNE 1999 - REVISED MARCH 2013 www.ti.com Figure 4. Typical Error Curve Timing Diagram Figure 5. The successive approximation register (SAR) performs 8 iterations to approximate the input voltage. For any SAR type converter, n-iterations are required for an n-bit converter. Figure 2 shows a typical example of a 3-bit converter. In the ADC0816,ADC0817, the approximation technique is extended to 8 bits using the 256Rnetwork. The A/D converter's successive approximation register (SAR)is reset on the positive edge of the start conversion (SC) pulse. The conversion is begun on the falling edge of the start conversion pulse. A conversion in process will be interrupted by receipt of a new start conversion pulse. Continuous conversion may be accomplished by tying the end-of-conversion(EOC) output to the SC input. If used in this mode, an external start conversion pulse should be applied after power up. End-of-conversion will go low between 0 and 8 clock pulses after the rising edge of start conversion. The most important section of the A/D converter is the comparator. It is this section which is responsible for the ultimate accuracy of the entire converter. It is also the comparator drift which has the greatest influence on the repeatability of the device. A chopper-stabilized comparator provides the most effective method of satisfying all the converter requirements. The chopper-stabilized comparator converts the DC input signal into an AC signal. This signal is then fed through a high gain AC amplifier and has the DC level restored. This technique limits the drift component of the amplifier since the drift is a DC component which is not passed by the AC amplifier. This makes the entire A/D converter extremely insensitive to temperature, long term drift and input offset errors. Figure 4 shows a typical error curve for the ADC0816 as measured using the procedures outlined in AN-179. 8 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 ADC0816, ADC0817 www.ti.com SNAS527C - JUNE 1999 - REVISED MARCH 2013 Typical Performance Characteristics Figure 6. Comparator IIN vs. VIN (VCC = VREF = 5V) Figure 7. Multiplexer RON vs. VIN (VCC = VREF = 5V) spacer TRI-STATE Test Circuits and Timing Diagrams Figure 8. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 Submit Documentation Feedback 9 ADC0816, ADC0817 SNAS527C - JUNE 1999 - REVISED MARCH 2013 www.ti.com APPLICATION INFORMATION OPERATION Ratiometric Conversion The ADC0816, ADC0817 is designed as a complete Data Acquisition System (DAS) for ratiometric conversion systems. In ratiometric systems, the physical variable being measured is expressed as a percentage of full-scale which is not necessarily related to an absolute standard. The voltage input to the ADC0816 is expressed by the equation (1) Where: VIN = Input voltage into the ADC0816 Vfs = Full-scale voltage VZ = Zero voltage DX = Data point being measured DMAX = Maximum data limit DMIN = Minimum data limit A good example of a ratiometric transducer is a potentiometer used as a position sensor. The position of the wiper is directly proportional to the output voltage which is a ratio of the full-scale voltage across it. Since the data is represented as a proportion of full-scale, reference requirements are greatly reduced, eliminating a large source of error and cost for many applications. A major advantage of the ADC0816, ADC0817 is that the input voltage range is equal to the supply range so the transducers can be connected directly across the supply and their outputs connected directly into the multiplexer inputs, (Figure 9). Ratiometric transducers such as potentiometers, strain gauges, thermistor bridges, pressure transducers, etc., are suitable for measuring proportional relationships; however, many types of measurements must be referred to an absolute standard such as voltage or current. This means a system reference must be used which relates the full-scale voltage to the standard volt. For example, if VCC = VREF = 5.12V, then the full-scale range is divided into 256 standard steps. The smallest standard step is 1 LSB which is then 20 mV. Resistor Ladder Limitations The voltages from the resistor ladder are compared to the selected input 8 times in a conversion. These voltages are coupled to the comparator via an analog switch tree which is referenced to the supply. The voltages at the top, center and bottom of the ladder must be controlled to maintain proper operation. The top of the ladder, Ref(+), should not be more positive than the supply, and the bottom of the ladder, Ref(-), should not be more negative than ground. The center of the ladder voltage must also be near the center of the supply because the analog switch tree changes from N-channel switches to P-channel switches. These limitations are automatically satisfied in ratiometric systems and can be easily met in ground referenced systems. Figure 10 shows a ground referenced system with a separate supply and reference. In this system, the supply must be trimmed to match the reference voltage. For instance, if a5.12V reference is used, the supply should be adjusted to the same voltage within 0.1V. 10 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 ADC0816, ADC0817 www.ti.com SNAS527C - JUNE 1999 - REVISED MARCH 2013 Figure 9. Ratiometric Conversion System The ADC0816 needs less than a milliamp of supply current so developing the supply from the reference is readily accomplished. In Figure 11 a ground references system is shown which generates the supply from the reference. The buffer shown can be an op amp of sufficient drive to supply the milliamp of supply current and the desired bus drive, or if a capacitive bus is driven by the outputs a large capacitor will supply the transient supply current as seen in Figure 12. The LM301 is overcompensated to insure stability when loaded by the 10 F output capacitor. The top and bottom ladder voltages cannot exceed VCCand ground, respectively, but they can be symmetrically less than VCC and greater than ground. The center of the ladder voltage should always be near the center of the supply. The sensitivity of the converter can be increased, (i.e., size of the LSB steps decreased) by using a symmetrical reference system. In Figure 13, a2.5V reference is symmetrically centered about VCC/2 since the same current flows in identical resistors. This system with a 2.5V reference allows the LSB to be half the size of the LSB in a 5V reference system. Figure 10. Ground Referenced Conversion System Using Trimmed Supply Figure 11. Ground Referenced Conversion System with Reference Generating VCC Supply Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 Submit Documentation Feedback 11 ADC0816, ADC0817 SNAS527C - JUNE 1999 - REVISED MARCH 2013 www.ti.com Figure 12. Typical Reference and Supply Circuit Figure 13. Symmetrically Centered Reference Converter Equations The transition between adjacent codes N and N + 1 is given by: (2) The center of an output code N is given by: (3) The output code N for an arbitrary input are the integers within the range: (4) where: VIN = Voltage at comparator input VREF = Voltage at Ref(+) VREF = Voltage at Ref(-) VTUE = Total unadjusted error voltage(typically VREF(+) /512) 12 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 ADC0816, ADC0817 www.ti.com SNAS527C - JUNE 1999 - REVISED MARCH 2013 Analog Comparator Inputs The dynamic comparator input current is caused by the periodic switching of on-chip stray capacitances These are connected alternately to the output of the resistor ladder/switch tree network and to the comparator input as part of the operation of the chopper stabilized comparator. The average value of the comparator input current varies directly with clock frequency and with VIN as shown in Figure 6. If no filter capacitors are used at the analog or comparator inputs and the signal source impedances are low, the comparator input current should not introduce converter errors, as the transient created by the capacitance discharge will die out before the comparator output is strobed. If input filter capacitors are desired for noise reduction and signal conditioning they will tend to average out the dynamic comparator input current. It will then take on the characteristics of a DC bias current whose effect can be predicted conventionally. See AN-258 for further discussion. Typical Application *Address latches needed for 8085 and SC/MP interfacing theADC0816, 17 to a microprocessor Microprocessor Interface Table PROCESSOR READ WRITE INTERRUPT(COMMENT) 8080 MEMR MEMW INTR (Thru RST Circuit) 8085 RD WR INTR (Thru RST Circuit) Z-80 RD WR INT (Thru RST Circuit, Mode 0) SC/MP NRDS NWDS SA (Thru Sense A) 6800 VMA*2*R/W VMA*Q2*R/W IRQA or IRQB (Thru PIA) Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 Submit Documentation Feedback 13 ADC0816, ADC0817 SNAS527C - JUNE 1999 - REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision B (March 2013) to Revision C * 14 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 13 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0816 ADC0817 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) ADC0816CCN NRND PDIP NFJ 40 9 TBD Call TI Call TI -40 to 85 ADC0816CCN ADC0816CCN/NOPB ACTIVE PDIP NFJ 40 9 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM -40 to 85 ADC0816CCN ADC0817CCN NRND PDIP NFJ 40 9 TBD Call TI Call TI -40 to 85 ADC0817CCN ADC0817CCN/NOPB ACTIVE PDIP NFJ 40 9 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM -40 to 85 ADC0817CCN (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA NFJ0040A N0040A N40A (Rev E) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated