Freescale Semiconductor MPC5634M Microcontroller Datasheet This is the MPC5634M Datasheet set consisting of the following files: * MPC5634M Datasheet Addendum (MPC5634M_AD), Rev. 1 * MPC5634M Datasheet (MPC5634M), Rev. 9 (c) Freescale Semiconductor, Inc., 2015. All rights reserved. MPC5634M Rev. 9.2, 01/2015 Freescale Semiconductor Datasheet Addendum MPC5634M_AD Rev. 1.0, 01/2015 MPC5634M Microcontroller Datasheet Addendum This addendum describes corrections to the MPC5634M Microcontroller Datasheet, order number MPC5634M. For convenience, the addenda items are grouped by revision. Please check our website at http://www.freescale.com/powerarchitecture for the latest updates. The current version available of the MPC5634M Microcontroller Datasheet is Revision 9. (c) Freescale Semiconductor, Inc., 2015. All rights reserved. Table of Contents 1 2 Addendum List for Revision 9 . . . . . . . . . . . . . . . . 2 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 Addendum List for Revision 9 4 Table 1. MPC5634M Rev 9 Addendum Location Description Section 4.11, "Temperature Sensor Electrical Characteristics", Page 81 2 In "Temperature Sensor Electrical Characteristics" table, update the Min and Max value of "Accuracy" parameter to -20oC and +20oC, respectively. Revision History Table 2 provides a revision history for this datasheet addendum document. Table 2. Revision History Table Rev. Number 1.0 Substantive Changes Initial release. Date of Release 12/2014 MPC5634M_AD, Rev. 1.0 2 Freescale Semiconductor How to Reach Us: Information in this document is provided solely to enable system and software Home Page: freescale.com implementers to use Freescale products. There are no express or implied copyright Web Support: freescale.com/support information in this document. licenses granted hereunder to design or fabricate any integrated circuits based on the Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address:freescale.com/SalesTermsandConditions. Freescale, the Freescale logo, AltiVec, C-5, CodeTest, CodeWarrior, ColdFire, C-Ware, Energy Efficient Solutions logo, Kinetis, mobileGT, PowerQUICC, Processor Expert, QorIQ, Qorivva, StarCore, Symphony, and VortiQa are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Airfast, BeeKit, BeeStack, ColdFire+, CoreNet, Flexis, MagniV, MXC, Platform in a Package, QorIQ Qonverge, QUICC Engine, Ready Play, SafeAssure, SMARTMOS, TurboLink, Vybrid, and Xtrinsic are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. (c) 2014 Freescale Semiconductor, Inc. Document Number: MPC5634M_AD Rev. 1.0 01/2015 Freescale Semiconductor Data Sheet: Advance Information Document Number: MPC5634M Rev. 9, 05/2012 MPC5634M 144 LQFP 20 mm x 20 mm MPC5634M Microcontroller Data Sheet * Operating Parameters -- Fully static operation, 0 MHz - 80 MHz (plus 2% frequency modulation - 82 MHz) -- -40 C to 150 C junction temperature operating range -- Low power design - Less than 400 mW power dissipation (nominal) - Designed for dynamic power management of core and peripherals - Software controlled clock gating of peripherals - Low power stop mode, with all clocks stopped -- Fabricated in 90 nm process -- 1.2 V internal logic -- Single power supply with 5.0 V 5% (4.5 V to 5.25 V) with internal regulator to provide 3.3 V and 1.2 V for the core -- Input and output pins with 5.0 V 5% (4.5 V to 5.25 V) range - 35%/65% VDDE CMOS switch levels (with hysteresis) - Selectable hysteresis - Selectable slew rate control -- Nexus pins powered by 3.3 V supply -- Designed with EMI reduction techniques - Phase-locked loop - Frequency modulation of system clock frequency - On-chip bypass capacitance - Selectable slew rate and drive strength 176 LQFP 24 mm x 24 mm * High performance e200z335 core processor -- 32-bit Power Architecture Book E programmer's model -- Variable Length Encoding Enhancements - Allows Power Architecture instruction set to be optionally encoded in a mixed 16 and 32-bit instructions - Results in smaller code size -- Single issue, 32-bit Power Architecture technology compliant CPU -- In-order execution and retirement -- Precise exception handling -- Branch processing unit - Dedicated branch address calculation adder - Branch acceleration using Branch Lookahead Instruction Buffer -- Load/store unit - One-cycle load latency - Fully pipelined - Big and Little Endian support - Misaligned access support - Zero load-to-use pipeline bubbles -- Thirty-two 64-bit general purpose registers (GPRs) -- Memory management unit (MMU) with 16-entry fully-associative translation look-aside buffer (TLB) -- Separate instruction bus and load/store bus -- Vectored interrupt support -- Interrupt latency < 120 ns @ 80 MHz (measured from interrupt request to execution of first instruction of interrupt exception handler) This document contains information on a product under development. Freescale reserves the right to change or discontinue this product without notice. (c) Freescale Semiconductor, Inc., 2008-2012. All rights reserved. 208 MAPBGA 17 mm x 17 mm Table of Contents 1 2 3 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 1.1 Document overview . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2.1 Device comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2.2 MPC5634M feature details . . . . . . . . . . . . . . . . . . . . . . .9 2.2.1 e200z335 core . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2.2.2 Crossbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.2.3 eDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.2.4 Interrupt controller . . . . . . . . . . . . . . . . . . . . . . .12 2.2.5 FMPLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 2.2.6 Calibration EBI. . . . . . . . . . . . . . . . . . . . . . . . . .13 2.2.7 SIU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.2.8 ECSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.2.9 Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.2.10 SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.2.11 BAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.2.12 eMIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2.2.13 eTPU2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 2.2.14 eQADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 2.2.15 DSPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 2.2.16 eSCI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 2.2.17 FlexCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 2.2.18 System timers . . . . . . . . . . . . . . . . . . . . . . . . . .23 2.2.19 Software Watchdog Timer (SWT) . . . . . . . . . . .24 2.2.20 Debug features . . . . . . . . . . . . . . . . . . . . . . . . .24 2.3 MPC5634M series architecture. . . . . . . . . . . . . . . . . . .26 2.3.1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . .26 2.3.2 Block summary . . . . . . . . . . . . . . . . . . . . . . . . .27 Pinout and signal description . . . . . . . . . . . . . . . . . . . . . . . . .29 3.1 144 LQFP pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 3.2 176 LQFP pinout (MPC5634M) . . . . . . . . . . . . . . . . . .30 3.3 176 LQFP pinout (MPC5633M) . . . . . . . . . . . . . . . . . .32 3.4 208 MAPBGA ballmap (MPC5634M) . . . . . . . . . . . . . .33 3.5 208 MAPBGA ballmap (MPC5633M only) . . . . . . . . . .34 3.6 Signal summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 3.7 Signal details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 4.1 Parameter classification . . . . . . . . . . . . . . . . . . . . . . . .56 4.2 4.3 5 6 7 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . 58 4.3.1 General notes for specifications at maximum junction temperature . . . . . . . . . . . . . . . . . . . . 60 4.4 Electromagnetic Interference (EMI) characteristics. . . 62 4.5 Electromagnetic static discharge (ESD) characteristics62 4.6 Power Management Control (PMC) and Power On Reset (POR) electrical specifications . 63 4.6.1 Regulator example . . . . . . . . . . . . . . . . . . . . . . 67 4.6.2 Recommended power transistors . . . . . . . . . . 69 4.7 Power up/down sequencing . . . . . . . . . . . . . . . . . . . . 69 4.8 DC electrical specifications . . . . . . . . . . . . . . . . . . . . . 70 4.9 I/O Pad current specifications . . . . . . . . . . . . . . . . . . . 77 4.9.1 I/O pad VRC33 current specifications . . . . . . . 78 4.9.2 LVDS pad specifications. . . . . . . . . . . . . . . . . . 79 4.10 Oscillator and PLLMRFM electrical characteristics . . . 80 4.11 Temperature sensor electrical characteristics . . . . . . . 82 4.12 eQADC electrical characteristics . . . . . . . . . . . . . . . . . 82 4.13 Platform flash controller electrical characteristics . . . . 85 4.14 Flash memory electrical characteristics. . . . . . . . . . . . 85 4.15 AC specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 4.15.1 Pad AC specifications . . . . . . . . . . . . . . . . . . . 87 4.16 AC timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 4.16.1 IEEE 1149.1 interface timing . . . . . . . . . . . . . . 90 4.16.2 Nexus timing . . . . . . . . . . . . . . . . . . . . . . . . . . 93 4.16.3 Calibration bus interface timing . . . . . . . . . . . . 96 4.16.4 eMIOS timing . . . . . . . . . . . . . . . . . . . . . . . . . . 99 4.16.5 DSPI timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 4.16.6 eQADC SSI timing . . . . . . . . . . . . . . . . . . . . . 105 Packages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 5.1 Package mechanical data . . . . . . . . . . . . . . . . . . . . . 106 5.1.1 144 LQFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 5.1.2 176 LQFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 5.1.3 208 MAPBGA. . . . . . . . . . . . . . . . . . . . . . . . . 113 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . 117 MPC5634M Microcontroller Data Sheet, Rev. 9 2 Freescale Semiconductor * * * -- Non-maskable interrupt (NMI) input for handling external events that must produce an immediate response, e.g., power down detection. On this device, the NMI input is connected to the Critical Interrupt Input. (May not be recoverable) -- Critical Interrupt input. For external interrupt sources that are higher priority than provided by the Interrupt Controller. (Always recoverable) -- New `Wait for Interrupt' instruction, to be used with new low power modes -- Reservation instructions for implementing read-modify-write accesses -- Signal processing extension (SPE) APU - Operating on all 32 GPRs that are all extended to 64 bits wide - Provides a full compliment of vector and scalar integer and floating point arithmetic operations (including integer vector MAC and MUL operations) (SIMD) - Provides rich array of extended 64-bit loads and stores to/from extended GPRs - Fully code compatible with e200z6 core -- Floating point (FPU) - IEEE 754 compatible with software wrapper - Scalar single precision in hardware, double precision with software library - Conversion instructions between single precision floating point and fixed point - Fully code compatible with e200z6 core -- Long cycle time instructions, except for guarded loads, do not increase interrupt latency -- Extensive system development support through Nexus debug port Advanced microcontroller bus architecture (AMBA) crossbar switch (XBAR) -- Three master ports, four slave ports - Masters: CPU Instruction bus; CPU Load/store bus (Nexus); eDMA - Slave: Flash; SRAM; Peripheral Bridge; calibration EBI -- 32-bit internal address bus, 64-bit internal data bus Enhanced direct memory access (eDMA) controller -- 32 channels support independent 8-bit, 16-bit, or 32-bit single value or block transfers -- Supports variable sized queues and circular queues -- Source and destination address registers are independently configured to post-increment or remain constant -- Each transfer is initiated by a peripheral, CPU, or eDMA channel request -- Each eDMA channel can optionally send an interrupt request to the CPU on completion of a single value or block transfer Interrupt controller (INTC) -- 191 peripheral interrupt request sources -- 8 software setable interrupt request sources -- 9-bit vector - Unique vector for each interrupt request source - Provided by hardware connection to processor or read from register -- Each interrupt source can be programmed to one of 16 priorities -- Preemption - Preemptive prioritized interrupt requests to processor - ISR at a higher priority preempts ISRs or tasks at lower priorities - Automatic pushing or popping of preempted priority to or from a LIFO - Ability to modify the ISR or task priority. Modifying the priority can be used to implement the Priority Ceiling Protocol for accessing shared resources. -- Low latency--three clocks from receipt of interrupt request from peripheral to interrupt request to processor MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 3 * * * Frequency Modulating Phase-locked loop (FMPLL) -- Reference clock pre-divider (PREDIV) for finer frequency synthesis resolution -- Reduced frequency divider (RFD) for reducing the FMPLL output clock frequency without forcing the FMPLL to re-lock -- System clock divider (SYSDIV) for reducing the system clock frequency in normal or bypass mode -- Input clock frequency range from 4 MHz to 20 MHz before the pre-divider, and from 4 MHz to 16 MHz at the FMPLL input -- Voltage controlled oscillator (VCO) range from 256 MHz to 512 MHz -- VCO free-running frequency range from 25 MHz to 125 MHz -- Four bypass modes: crystal or external reference with PLL on or off -- Two normal modes: crystal or external reference -- Programmable frequency modulation - Triangle wave modulation - Register programmable modulation frequency and depth -- Lock detect circuitry reports when the FMPLL has achieved frequency lock and continuously monitors lock status to report loss of lock conditions - User-selectable ability to generate an interrupt request upon loss of lock - User-selectable ability to generate a system reset upon loss of lock -- Clock quality monitor (CQM) module provides loss-of-clock detection for the FMPLL reference and output clocks - User-selectable ability to generate an interrupt request upon loss of clock - User-selectable ability to generate a system reset upon loss of clock - Backup clock (reference clock or FMPLL free-running) can be applied to the system in case of loss of clock Calibration bus interface (EBI) -- Available only in the calibration package (496 CSP package) -- 1.8 V to 3.3 V 10% I/O (1.6 V to 3.6 V) -- Memory controller with support for various memory types -- 16-bit data bus, up to 22-bit address bus -- Selectable drive strength -- Configurable bus speed modes -- Bus monitor -- Configurable wait states System integration unit (SIU) -- Centralized GPIO control of 80 I/O pins -- Centralized pad control on a per-pin basis - Pin function selection - Configurable weak pull-up or pull-down - Drive strength - Slew rate - Hysteresis -- System reset monitoring and generation -- External interrupt inputs, filtering and control -- Critical Interrupt control -- Non-Maskable Interrupt control -- Internal multiplexer subblock (IMUX) - Allows flexible selection of eQADC trigger inputs (eTPU, eMIOS and external signals) MPC5634M Microcontroller Data Sheet, Rev. 9 4 Freescale Semiconductor * * * * * * * - Allows selection of interrupt requests between external pins and DSPI Error correction status module (ECSM) -- Configurable error-correcting codes (ECC) reporting -- Single-bit error correction reporting On-chip flash memory -- Up to 1.5 MB flash memory, accessed via a 64-bit wide bus interface -- 16 KB shadow block -- Fetch Accelerator - Provide single cycle flash access at 80 MHz - Quadruple 128-bit wide prefetch/burst buffers - Prefetch buffers can be configured to prefetch code or data or both -- Censorship protection scheme to prevent flash content visibility -- Flash divided into two independent arrays, allowing reading from one array while erasing/programming the other array (used for EEPROM emulation) -- Memory block: - For MPC5634M: 18 blocks (4 16 KB, 2 32 KB, 2 64 KB, 10 128 KB) - For MPC5633M: 14 blocks (4 16 KB, 2 32 KB, 2 64 KB, 6 128 KB) - For MPC5632M: 12 blocks (4 16 KB, 2 32 KB, 2 64 KB, 4 128 KB) -- Hardware programming state machine On-chip static RAM -- For MPC5634M: 94 KB general purpose RAM of which 32 KB are on standby power supply -- For MPC5633M: 64 KB general purpose RAM of which 32 KB are on standby power supply -- For MPC5632M: 48 KB general purpose RAM of which 24 KB are on standby power supply Boot assist module (BAM) -- Enables and manages the transition of MCU from reset to user code execution in the following configurations: - Execution from internal flash memory - Execution from external memory on the calibration bus - Download and execution of code via FlexCAN or eSCI Periodic interrupt timer (PIT) -- 32-bit wide down counter with automatic reload -- Four channels clocked by system clock -- One channel clocked by crystal clock -- Each channel can produce periodic software interrupt -- Each channel can produce periodic triggers for eQADC queue triggering -- One channel out of the five can be used as wake-up timer to wake device from low power stop mode System timer module (STM) -- 32-bit up counter with 8-bit prescaler -- Clocked from system clock -- Four-channel timer compare hardware -- Each channel can generate a unique interrupt request -- Designed to address AUTOSAR task monitor function Software watchdog timer (SWT) -- 32-bit timer -- Clock by system clock or crystal clock -- Can generate either system reset or non-maskable interrupt followed by system reset MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 5 * * * -- Enabled out of reset Enhanced modular I/O system (eMIOS) -- 16 timer channels (up to 14 channels in 144 LQFP) -- 24-bit timer resolution -- Supports a subset of the timer modes found in eMIOS on MPC5554 -- 3 selectable time bases plus shared time or angle counter bus from eTPU2 -- DMA and interrupt request support -- Motor control capability Second-generation enhanced time processor unit (eTPU2) -- Object-code compatible with eTPU--no changes are required to hardware or software if only eTPU features are used -- Intelligent co-processor designed for timing control -- High level tools, assembler and compiler available -- 32 channels (each channel has dedicated I/O pin in all packages) -- 24-bit timer resolution -- 14 KB code memory and 3 KB data memory -- Double match and capture on all channels -- Angle clock hardware support -- Shared time or angle counter bus with eMIOS -- DMA and interrupt request support -- Nexus Class 1 debug support -- eTPU2 enhancements - Counters and channels can run at full system clock speed - Software watchdog - Real-time performance monitor - Instruction set enhancements for smaller more flexible code generation - Programmable channel mode for customization of channel operation Enhanced queued A/D converter (eQADC) -- Two independent on-chip redundant signed digit (RSD) cyclic ADCs - 8-, 10-, and 12-bit resolution - Differential conversions - Targets up to 10-bit accuracy at 500 KSample/s (ADC_CLK = 7.5 MHz) and 8-bit accuracy at 1 MSample/s (ADC_CLK = 15 MHz) for differential conversions - Differential channels include variable gain amplifier (VGA) for improved dynamic range (1; 2; 4) - Differential channels include programmable pull-up and pull-down resistors for biasing and sensor diagnostics (200 k; 100 k; low value of 5 k) - Single-ended signal range from 0 to 5 V - Sample times of 2 (default), 8, 64 or 128 ADC clock cycles - Provides time stamp information when requested - Parallel interface to eQADC command FIFOs (CFIFOs) and result FIFOs (RFIFOs) - Supports both right-justified unsigned and signed formats for conversion results - Temperature sensor to enable measurement of die temperature - Ability to measure all power supply pins directly -- Automatic application of ADC calibration constants - Provision of reference voltages (25% VREF and 75% VREF) for ADC calibration purposes -- Up to 341 input channels available to the two on-chip ADCs MPC5634M Microcontroller Data Sheet, Rev. 9 6 Freescale Semiconductor * * -- Four pairs of differential analog input channels -- Full duplex synchronous serial interface to an external device - Has a free-running clock for use by the external device - Supports a 26-bit message length - Transmits a null message when there are no triggered CFIFOs with commands bound for external CBuffers, or when there are triggered CFIFOs with commands bound for external CBuffers but the external CBuffers are full -- Parallel Side Interface to communicate with an on-chip companion module -- Zero jitter triggering for queue 0. (Queue 0 trigger causes current conversion to be aborted and the queued conversions in the CBUFFER to be bypassed. Delay from Trigger to start of conversion is 13 system clocks + 1 ADC clock.) -- eQADC Result Streaming. Generation of a continuous stream of ADC conversion results from a single eQADC command word. Controlled by two different trigger signals; one to define the rate at which results are generated and the other to define the beginning and ending of the stream. Used to digitize waveforms during specific time/angle windows, e.g., engine knock sensor sampling. -- Angular Decimation. The ability of the eQADC to sample an analog waveform in the time domain, perform Finite Impulse Response (FIR) or Infinite Impulse Response (IIR) filtering also in the time domain, but to down sample the results in the angle domain. Resulting in a time domain filtered result at a given engine angle. -- Priority Based CFIFOs - Supports six CFIFOs with fixed priority. The lower the CFIFO number, the higher its priority. When commands of distinct CFIFOs are bound for the same CBuffer, the higher priority CFIFO is always served first. - Supports software and several hardware trigger modes to arm a particular CFIFO - Generates interrupt when command coherency is not achieved -- External Hardware Triggers - Supports rising edge, falling edge, high level and low level triggers - Supports configurable digital filter -- Supports four external 8-to-1 muxes which can expand the input channel number from 341 to 59 Two deserial serial peripheral interface modules (DSPI) -- SPI - Full duplex communication ports with interrupt and DMA request support - Supports all functional modes from QSPI subblock of QSMCM (MPC5xx family) - Support for queues in RAM - 6 chip selects, expandable to 64 with external demultiplexers - Programmable frame size, baud rate, clock delay and clock phase on a per frame basis - Modified SPI mode for interfacing to peripherals with longer setup time requirements - LVDS option for output clock and data to allow higher speed communication -- Deserial serial interface (DSI) - Pin reduction by hardware serialization and deserialization of eTPU, eMIOS channels and GPIO - 32 bits per DSPI module - Triggered transfer control and change in data transfer control (for reduced EMI) - Compatible with Microsecond Channel Version 1.0 downstream Two enhanced serial communication interface (eSCI) modules -- UART mode provides NRZ format and half or full duplex interface -- eSCI bit rate up to 1 Mbps 1. 176-pin and 208-pin packages have 34 input channels; 144-pin package has 32. 1. 176-pin and 208-ball packages. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 7 * * * * * -- Advanced error detection, and optional parity generation and detection -- Word length programmable as 8, 9, 12 or 13 bits -- Separately enabled transmitter and receiver -- LIN support -- DMA support -- Interrupt request support -- Programmable clock source: system clock or oscillator clock -- Support Microsecond Channel (Timed Serial Bus - TSB) upstream Version 1.0 Two FlexCAN -- One with 32 message buffers; the second with 64 message buffers -- Full implementation of the CAN protocol specification, Version 2.0B -- Based on and including all existing features of the Freescale TouCAN module -- Programmable acceptance filters -- Short latency time for high priority transmit messages -- Arbitration scheme according to message ID or message buffer number -- Listen only mode capabilities -- Programmable clock source: system clock or oscillator clock -- Message buffers may be configured as mailboxes or as FIFO Nexus port controller (NPC) -- Per IEEE-ISTO 5001-2003 -- Real time development support for Power Architecture core and eTPU engine through Nexus class 2/1 -- Read and write access (Nexus class 3 feature that is supported on this device) - Run-time access of entire memory map - Calibration -- Support for data value breakpoints / watchpoints - Run-time access of entire memory map - Calibration Table constants calibrated using MMU and internal and external RAM Scalar constants calibrated using cache line locking -- Configured via the IEEE 1149.1 (JTAG) port IEEE 1149.1 JTAG controller (JTAGC) -- IEEE 1149.1-2001 Test Access Port (TAP) interface -- 5-bit instruction register that supports IEEE 1149.1-2001 defined instructions -- 5-bit instruction register that supports additional public instructions -- Three test data registers: a bypass register, a boundary scan register, and a device identification register -- Censorship disable register. By writing the 64-bit serial boot password to this register, Censorship may be disabled until the next reset -- TAP controller state machine that controls the operation of the data registers, instruction register and associated circuitry On-chip Voltage Regulator for single 5 V supply operation -- On-chip regulator 5 V to 3.3 V for internal supplies -- On-chip regulator controller 5 V to 1.2 V (with external bypass transistor) for core logic Low-power modes -- SLOW Mode. Allows device to be run at very low speed (approximately 1 MHz), with modules (including the PLL) selectively disabled in software -- STOP Mode. System clock stopped to all modules including the CPU. Wake-up timer used to restart the system clock after a predetermined time MPC5634M Microcontroller Data Sheet, Rev. 9 8 Freescale Semiconductor Introduction 1 Introduction 1.1 Document overview This document provides an overview and describes the features of the MPC5634M series of microcontroller units (MCUs). For functional characteristics, refer to the device reference manual. Electrical specifications and package mechanical drawings are included in this device data sheet. Pin assignments can be found in both the reference manual and data sheet. 1.2 Description These 32-bit automotive microcontrollers are a family of system-on-chip (SoC) devices that contain all the features of the MPC5500 family and many new features coupled with high performance 90 nm CMOS technology to provide substantial reduction of cost per feature and significant performance improvement. The advanced and cost-efficient host processor core of this automotive controller family is built on Power Architecture(R) technology. This family contains enhancements that improve the architecture's fit in embedded applications, includes additional instruction support for digital signal processing (DSP), integrates technologies--such as an enhanced time processor unit, enhanced queued analog-to-digital converter, Controller Area Network, and an enhanced modular input-output system--that are important for today's lower-end powertrain applications. This device family is a completely compatible extension to Freescale's MPC5500 family. The device has a single level of memory hierarchy consisting of up to 94 KB on-chip SRAM and up to 1.5 MB of internal flash memory. The device also has an external bus interface (EBI) for `calibration'. This external bus interface has been designed to support most of the standard memories used with the MPC5xx and MPC55xx families. 2 Overview This document provides electrical specifications, pin assignments, and package diagrams for the MPC5634M series of microcontroller units (MCUs). For functional characteristics, refer to the MPC5634M Microcontroller Reference Manual. The MPC5634M series microcontrollers are system-on-chip devices that are built on Power Architecture(R) technology and: * * * * Are 100% user-mode compatible with the Power Architecture instruction set Contain enhancements that improve the architecture's fit in embedded applications Include additional instruction support for digital signal processing (DSP) Integrate technologies such as an enhanced time processor unit, enhanced queued analog-to-digital converter, Controller Area Network, and an enhanced modular input-output system 2.1 Device comparison 2.2 MPC5634M feature details 2.2.1 e200z335 core The e200z335 processor utilizes a four stage pipeline for instruction execution. The Instruction Fetch (stage 1), Instruction Decode/Register file Read/Effective Address Calculation (stage 2), Execute/Memory Access (stage 3), and Register Writeback (stage 4) stages operate in an overlapped fashion, allowing single clock instruction execution for most instructions. The integer execution unit consists of a 32-bit Arithmetic Unit (AU), a Logic Unit (LU), a 32-bit Barrel shifter (Shifter), a Mask-Insertion Unit (MIU), a Condition Register manipulation Unit (CRU), a Count-Leading-Zeros unit (CLZ), a 3232 Hardware Multiplier array, result feed-forward hardware, and support hardware for division. Most arithmetic and logical operations are executed in a single cycle with the exception of the divide instructions. A Count-Leading-Zeros unit operates in a single clock cycle. The Instruction Unit contains a PC incrementer and a dedicated MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 9 Overview Branch Address adder to minimize delays during change of flow operations. Sequential prefetching is performed to ensure a supply of instructions into the execution pipeline. Branch target prefetching is performed to accelerate taken branches. Prefetched instructions are placed into an instruction buffer capable of holding six instructions. Branches can also be decoded at the instruction buffer and branch target addresses calculated prior to the branch reaching the instruction decode stage, allowing the branch target to be prefetched early. When a branch is detected at the instruction buffer, a prediction may be made on whether the branch is taken or not. If the branch is predicted to be taken, a target fetch is initiated and its target instructions are placed in the instruction buffer following the branch instruction. Many branches take zero cycle to execute by using branch folding. Branches are folded out from the instruction execution pipe whenever possible. These include unconditional branches and conditional branches with condition codes that can be resolved early. Conditional branches which are not taken and not folded execute in a single clock. Branches with successful target prefetching which are not folded have an effective execution time of one clock. All other taken branches have an execution time of two clocks. Memory load and store operations are provided for byte, halfword, and word (32-bit) data with automatic zero or sign extension of byte and halfword load data as well as optional byte reversal of data. These instructions can be pipelined to allow effective single cycle throughput. Load and store multiple word instructions allow low overhead context save and restore operations. The load/store unit contains a dedicated effective address adder to allow effective address generation to be optimized. Also, a load-to-use dependency does not incur any pipeline bubbles for most cases. The Condition Register unit supports the condition register (CR) and condition register operations defined by the Power Architecture. The condition register consists of eight 4-bit fields that reflect the results of certain operations, such as move, integer and floating-point compare, arithmetic, and logical instructions, and provide a mechanism for testing and branching. Vectored and autovectored interrupts are supported by the CPU. Vectored interrupt support is provided to allow multiple interrupt sources to have unique interrupt handlers invoked with no software overhead. The hardware floating-point unit utilizes the IEEE-754 single-precision floating-point format and supports single-precision floating-point operations in a pipelined fashion. The general purpose register file is used for source and destination operands, thus there is a unified storage model for single-precision floating-point data types of 32 bits and the normal integer type. Single-cycle floating-point add, subtract, multiply, compare, and conversion operations are provided. Divide instructions are multi-cycle and are not pipelined. The Signal Processing Extension (SPE) Auxiliary Processing Unit (APU) provides hardware SIMD operations and supports a full complement of dual integer arithmetic operation including Multiply Accumulate (MAC) and dual integer multiply (MUL) in a pipelined fashion. The general purpose register file is enhanced such that all 32 of the GPRs are extended to 64 bits wide and are used for source and destination operands, thus there is a unified storage model for 3232 MAC operations which generate greater than 32-bit results. The majority of both scalar and vector operations (including MAC and MUL) are executed in a single clock cycle. Both scalar and vector divides take multiple clocks. The SPE APU also provides extended load and store operations to support the transfer of data to and from the extended 64-bit GPRs. This SPE APU is fully binary compatible with e200z6 SPE APU used in MPC5554 and MPC5553. The CPU includes support for Variable Length Encoding (VLE) instruction enhancements. This enables the classic Power Architecture instruction set to be represented by a modified instruction set made up from a mixture of 16- and 32-bit instructions. This results in a significantly smaller code size footprint without noticeably affecting performance. The Power Architecture instruction set and VLE instruction set are available concurrently. Regions of the memory map are designated as PPC or VLE using an additional configuration bit in each of Table Look-aside Buffers (TLB) entries in the MMU. The CPU core is enhanced by the addition of two additional interrupt sources; Non-Maskable Interrupt and Critical Interrupt. These two sources are routed directly from package pins, via edge detection logic in the SIU to the CPU, bypassing completely the Interrupt Controller. Once the edge detection logic is programmed, it cannot be disabled, except by reset. The non-maskable Interrupt is, as the name suggests, completely un-maskable and when asserted will always result in the immediate execution of the respective interrupt service routine. The non-maskable interrupt is not guaranteed to be recoverable. The Critical Interrupt is very similar to the non-maskable interrupt, but it can be masked by other exceptional interrupts in the CPU and is guaranteed to be recoverable (code execution may be resumed from where it stopped). MPC5634M Microcontroller Data Sheet, Rev. 9 10 Freescale Semiconductor Overview The CPU core has an additional `Wait for Interrupt' instruction that is used in conjunction with low power STOP mode. When Low Power Stop mode is selected, this instruction is executed to allow the system clock to be stopped. An external interrupt source or the system wake-up timer is used to restart the system clock and allow the CPU to service the interrupt. 2.2.2 Crossbar The XBAR multi-port crossbar switch supports simultaneous connections between three master ports and four slave ports. The crossbar supports a 32-bit address bus width and a 64-bit data bus width. The crossbar allows three concurrent transactions to occur from the master ports to any slave port; but each master must access a different slave. If a slave port is simultaneously requested by more than one master port, arbitration logic selects the higher priority master and grants it ownership of the slave port. All other masters requesting that slave port are stalled until the higher priority master completes its transactions. Requesting masters are treated with equal priority and are granted access to a slave port in round-robin fashion, based upon the ID of the last master to be granted access. The crossbar provides the following features: * * * 2.2.3 3 master ports: -- e200z335 core complex Instruction port -- e200z335 core complex Load/Store port -- eDMA 4 slave ports -- FLASH -- calibration bus -- SRAM -- Peripheral bridge A/B (eTPU2, eMIOS, SIU, DSPI, eSCI, FlexCAN, eQADC, BAM, decimation filter, PIT, STM and SWT) 32-bit internal address, 64-bit internal data paths eDMA The enhanced direct memory access (eDMA) controller is a second-generation module capable of performing complex data movements via 32 programmable channels, with minimal intervention from the host processor. The hardware micro architecture includes a DMA engine which performs source and destination address calculations, and the actual data movement operations, along with an SRAM-based memory containing the transfer control descriptors (TCD) for the channels. This implementation is utilized to minimize the overall block size. The eDMA module provides the following features: * * * * * * * * * * * All data movement via dual-address transfers: read from source, write to destination Programmable source and destination addresses, transfer size, plus support for enhanced addressing modes Transfer control descriptor organized to support two-deep, nested transfer operations An inner data transfer loop defined by a "minor" byte transfer count An outer data transfer loop defined by a "major" iteration count Channel activation via one of three methods: -- Explicit software initiation -- Initiation via a channel-to-channel linking mechanism for continuous transfers -- Peripheral-paced hardware requests (one per channel) Support for fixed-priority and round-robin channel arbitration Channel completion reported via optional interrupt requests 1 interrupt per channel, optionally asserted at completion of major iteration count Error termination interrupts are optionally enabled Support for scatter/gather DMA processing MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 11 Overview * 2.2.4 Channel transfers can be suspended by a higher priority channel Interrupt controller The INTC (interrupt controller) provides priority-based preemptive scheduling of interrupt requests, suitable for statically scheduled hard real-time systems. The INTC allows interrupt request servicing from up to 191 peripheral interrupt request sources, plus 165 sources reserved for compatibility with other family members). For high priority interrupt requests, the time from the assertion of the interrupt request from the peripheral to when the processor is executing the interrupt service routine (ISR) has been minimized. The INTC provides a unique vector for each interrupt request source for quick determination of which ISR needs to be executed. It also provides an ample number of priorities so that lower priority ISRs do not delay the execution of higher priority ISRs. To allow the appropriate priorities for each source of interrupt request, the priority of each interrupt request is software configurable. When multiple tasks share a resource, coherent accesses to that resource need to be supported. The INTC supports the priority ceiling protocol for coherent accesses. By providing a modifiable priority mask, the priority can be raised temporarily so that all tasks which share the resource can not preempt each other. Multiple processors can assert interrupt requests to each other through software setable interrupt requests. These same software setable interrupt requests also can be used to break the work involved in servicing an interrupt request into a high priority portion and a low priority portion. The high priority portion is initiated by a peripheral interrupt request, but then the ISR asserts a software setable interrupt request to finish the servicing in a lower priority ISR. Therefore these software setable interrupt requests can be used instead of the peripheral ISR scheduling a task through the RTOS. The INTC provides the following features: * * * * * * * * * * * 356 peripheral interrupt request sources 8 software setable interrupt request sources 9-bit vector addresses Unique vector for each interrupt request source Hardware connection to processor or read from register Each interrupt source can be programmed to one of 16 priorities Preemptive prioritized interrupt requests to processor ISR at a higher priority preempts executing ISRs or tasks at lower priorities Automatic pushing or popping of preempted priority to or from a LIFO Ability to modify the ISR or task priority to implement the priority ceiling protocol for accessing shared resources Low latency--three clocks from receipt of interrupt request from peripheral to interrupt request to processor This device also includes a non-maskable interrupt (NMI) pin that bypasses the INTC and multiplexing logic. 2.2.5 FMPLL The FMPLL allows the user to generate high speed system clocks from a 4 MHz to 20 MHz crystal oscillator or external clock generator. Further, the FMPLL supports programmable frequency modulation of the system clock. The PLL multiplication factor, output clock divider ratio are all software configurable. The PLL has the following major features: * * * * Input clock frequency from 4 MHz to 20 MHz Voltage controlled oscillator (VCO) range from 256 MHz to 512 MHz, resulting in system clock frequencies from 16 MHz to 80 MHz with granularity of 4 MHz or better Reduced frequency divider (RFD) for reduced frequency operation without forcing the PLL to relock 3 modes of operation -- Bypass mode with PLL off -- Bypass mode with PLL running (default mode out of reset) -- PLL normal mode MPC5634M Microcontroller Data Sheet, Rev. 9 12 Freescale Semiconductor Overview * * * * * 2.2.6 Each of the three modes may be run with a crystal oscillator or an external clock reference Programmable frequency modulation -- Modulation enabled/disabled through software -- Triangle wave modulation up to 100 kHz modulation frequency -- Programmable modulation depth (0% to 2% modulation depth) -- Programmable modulation frequency dependent on reference frequency Lock detect circuitry reports when the PLL has achieved frequency lock and continuously monitors lock status to report loss of lock conditions Clock Quality Module -- detects the quality of the crystal clock and cause interrupt request or system reset if error is detected -- detects the quality of the PLL output clock. If an error is detected, causes a system reset or switches the system clock to the crystal clock and causes an interrupt request Programmable interrupt request or system reset on loss of lock Calibration EBI The Calibration EBI controls data transfer across the crossbar switch to/from memories or peripherals attached to the VertiCal connector in the calibration address space. The Calibration EBI is only available in the VertiCal Calibration System. The Calibration EBI includes a memory controller that generates interface signals to support a variety of external memories. The Calibration EBI memory controller supports legacy flash, SRAM, and asynchronous memories. In addition, the calibration EBI supports up to three regions via chip selects (two chip selects are multiplexed with two address bits), along with programmed region-specific attributes. The calibration EBI supports the following features: * * * 22-bit address bus (two most significant signals multiplexed with two chip selects) 16-bit data bus Multiplexed mode with addresses and data signals present on the data lines NOTE The calibration EBI must be configured in multiplexed mode when the extended Nexus trace is used on the VertiCal Calibration System. This is because Nexus signals and address lines of the calibration bus share the same balls in the calibration package. * * * * * * * * * Memory controller with support for various memory types: -- Asynchronous/legacy flash and SRAM -- Most standard memories used with the MPC5xx or MPC55xx family Bus monitor -- User selectable -- Programmable timeout period (with 8 external bus clock resolution) Configurable wait states (via chip selects) 3 chip-select (Cal_CS[0], Cal_CS[2:3]) signals (Multiplexed with 2 most significant address signals) 2 write/byte enable (WE[0:1]/BE[0:1]) signals Configurable bus speed modes -- system frequency -- 1/2 of system frequency -- 1/4 of system frequency Optional automatic CLKOUT gating to save power and reduce EMI Compatible with MPC5xx external bus (with some limitations) Selectable drive strengths; 10 pF, 20 pF, 30 pF, 50 pF MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 13 Overview 2.2.7 SIU The MPC5634MSIU controls MCU reset configuration, pad configuration, external interrupt, general purpose I/O (GPIO), internal peripheral multiplexing, and the system reset operation. The reset configuration block contains the external pin boot configuration logic. The pad configuration block controls the static electrical characteristics of I/O pins. The GPIO block provides uniform and discrete input/output control of the I/O pins of the MCU. The reset controller performs reset monitoring of internal and external reset sources, and drives the RSTOUT pin. Communication between the SIU and the e200z335 CPU core is via the crossbar switch. The SIU provides the following features: * * * * * 2.2.8 System configuration -- MCU reset configuration via external pins -- Pad configuration control for each pad -- Pad configuration control for virtual I/O via DSPI serialization System reset monitoring and generation -- Power-on reset support -- Reset status register provides last reset source to software -- Glitch detection on reset input -- Software controlled reset assertion External interrupt -- 11 interrupt requests -- Rising or falling edge event detection -- Programmable digital filter for glitch rejection -- Critical Interrupt request -- Non-Maskable Interrupt request GPIO -- GPIO function on 80 I/O pins -- Virtual GPIO on 64 I/O pins via DSPI serialization (requires external deserialization device) -- Dedicated input and output registers for setting each GPIO and Virtual GPIO pin Internal multiplexing -- Allows serial and parallel chaining of DSPIs -- Allows flexible selection of eQADC trigger inputs -- Allows selection of interrupt requests between external pins and DSPI ECSM The error correction status module provides status information regarding platform memory errors reported by error-correcting codes. 2.2.9 Flash Devices in the MPC5634M family provide up to 1.5 MB of programmable, non-volatile, flash memory. The non-volatile memory (NVM) can be used for instruction and/or data storage. The flash module includes a Fetch Accelerator, that optimizes the performance of the flash array to match the CPU architecture and provides single cycle random access to the flash @ 80 MHz. The flash module interfaces the system bus to a dedicated flash memory array controller. For CPU `loads', DMA transfers and CPU instruction fetch, it supports a 64-bit data bus width at the system bus port, and a 128-bit read data interface to flash memory. The module contains a four-entry, 128-bit prefetch buffer and a prefetch controller which prefetches sequential lines of data from the flash array into the buffer. Prefetch buffer hits allow no-wait responses. Normal flash array accesses are registered and are forwarded to the system bus on the following cycle, incurring three wait-states. Prefetch operations may be automatically controlled, and are restricted to instruction fetch. MPC5634M Microcontroller Data Sheet, Rev. 9 14 Freescale Semiconductor Overview The flash memory provides the following features: * * * * * * * * * * * * * * * * * Supports a 64-bit data bus for instruction fetch, CPU loads and DMA access. Byte, halfword, word and doubleword reads are supported. Only aligned word and doubleword writes are supported. Fetch Accelerator -- Architected to optimize the performance of the flash with the CPU to provide single cycle random access to the flash up to 80 MHz system clock speed -- Configurable read buffering and line prefetch support -- Four line read buffers (128 bits wide) and a prefetch controller Hardware and software configurable read and write access protections on a per-master basis Interface to the flash array controller is pipelined with a depth of one, allowing overlapped accesses to proceed in parallel for interleaved or pipelined flash array designs Configurable access timing allowing use in a wide range of system frequencies Multiple-mapping support and mapping-based block access timing (0-31 additional cycles) allowing use for emulation of other memory types Software programmable block program/erase restriction control Erase of selected block(s) Read page size of 128 bits (four words) ECC with single-bit correction, double-bit detection Program page size of 64 bits (two words) ECC single-bit error corrections are visible to software Minimum program size is two consecutive 32-bit words, aligned on a 0-modulo-8 byte address, due to ECC Embedded hardware program and erase algorithm Erase suspend Shadow information stored in non-volatile shadow block Independent program/erase of the shadow block 2.2.10 SRAM The MPC5634M SRAM module provides a general-purpose up to 94 KB memory block. The SRAM controller includes these features: * * * * Supports read/write accesses mapped to the SRAM memory from any master 32 KB or 24 KB block powered by separate supply for standby operation Byte, halfword, word and doubleword addressable ECC performs single-bit correction, double-bit detection on 32-bit data element 2.2.11 BAM The BAM (Boot Assist Module) is a block of read-only memory that is programmed once by Freescale and is identical for all MPC5634M MCUs. The BAM program is executed every time the MCU is powered-on or reset in normal mode. The BAM supports different modes of booting. They are: * * * Booting from internal flash memory Serial boot loading (A program is downloaded into RAM via eSCI or the FlexCAN and then executed) Booting from external memory on calibration bus The BAM also reads the reset configuration half word (RCHW) from internal flash memory and configures the MPC5634M hardware accordingly. The BAM provides the following features: * Sets up MMU to cover all resources and mapping all physical address to logical addresses with minimum address translation MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 15 Overview * * * * * * * * * * * Sets up the MMU to allow user boot code to execute as either Power Architecture code (default) or as Freescale VLE code Detection of user boot code Automatic switch to serial boot mode if internal flash is blank or invalid Supports user programmable 64-bit password protection for serial boot mode Supports serial bootloading via FlexCAN bus and eSCI using Freescale protocol Supports serial bootloading via FlexCAN bus and eSCI with auto baud rate sensing Supports serial bootloading of either Power Architecture code (default) or Freescale VLE code Supports booting from calibration bus interface Supports censorship protection for internal flash memory Provides an option to enable the core watchdog timer Provides an option to disable the software watchdog timer 2.2.12 eMIOS The eMIOS (Enhanced Modular Input Output System) module provides the functionality to generate or measuretime events. The channels on this module provide a range of operating modes including the capability to perform dual input capture or dual output compare as well as PWM output. The eMIOS provides the following features: * * * * * * * * 16 channels (24-bit timer resolution) For compatibility with other family members selected channels and timebases are implemented: -- Channels 0 to 6, 8 to 15, and 23 -- Timebases A, B and C Channels 1, 3, 5 and 6 support modes: -- General Purpose Input/Output (GPIO) -- Single Action Input Capture (SAIC) -- Single Action Output Compare (SAOC) Channels 2, 4, 11 and 13 support all the modes above plus: -- Output Pulse Width Modulation Buffered (OPWMB) Channels 0, 8, 9, 10, 12, 14, 15, 23 support all the modes above plus: -- Input Period Measurement (IPM) -- Input Pulse Width Measurement (IPWM) -- Double Action Output Compare (set flag on both matches) (DAOC) -- Modulus Counter Buffered (MCB) -- Output Pulse Width and Frequency Modulation Buffered (OPWFMB) Three 24-bit wide counter buses -- Counter bus A can be driven by channel 23 or by the eTPU2 and all channels can use it as a reference -- Counter bus B is driven by channel 0 and channels 0 to 6 can use it as a reference -- Counter bus C is driven by channel 8 and channels 8 to 15 can use it as a reference Shared time bases with the eTPU2 through the counter buses Synchronization among internal and external time bases 2.2.13 eTPU2 The eTPU2 is an enhanced co-processor designed for timing control. Operating in parallel with the host CPU, eTPU2 processes instructions and real-time input events, performs output waveform generation, and accesses shared data without host MPC5634M Microcontroller Data Sheet, Rev. 9 16 Freescale Semiconductor Overview intervention. Consequently, for each timer event, the host CPU setup and service times are minimized or eliminated. A powerful timer subsystem is formed by combining the eTPU2 with its own instruction and data RAM. High-level assembler/compiler and documentation allows customers to develop their own functions on the eTPU2. The eTPU2 includes these distinctive features: * * * * * * * * * * * * * * * The Timer Counter (TCR1), channel logic and digital filters (both channel and the external timer clock input [TCRCLK]) now have an option to run at full system clock speed or system clock / 2. Channels support unordered transitions: transition 2 can now be detected before transition 1. Related to this enhancement, the transition detection latches (TDL1 and TDL2) can now be independently negated by microcode. A new User Programmable Channel Mode has been added: the blocking, enabling, service request and capture characteristics of this channel mode can be programmed via microcode. Microinstructions now provide an option to issue Interrupt and Data Transfer requests selected by channel. They can also be requested simultaneously at the same instruction. Channel Flags 0 and 1 can now be tested for branching, in addition to selecting the entry point. Channel digital filters can be bypassed. The Timer Counter (TCR1), channel logic and digital filters (both channel and the external timer clock input [TCRCLK]) now have an option to run at full system clock speed or system clock / 2. Channels support unordered transitions: transition 2 can now be detected before transition 1. Related to this enhancement, the transition detection latches (TDL1 and TDL2) can now be independently negated by microcode. A new User Programmable Channel Mode has been added: the blocking, enabling, service request and capture characteristics of this channel mode can be programmed via microcode. Microinstructions now provide an option to issue Interrupt and Data Transfer requests selected by channel. They can also be requested simultaneously at the same instruction. Channel Flags 0 and 1 can now be tested for branching, in addition to selecting the entry point. Channel digital filters can be bypassed. 32 channels, each channel is associated with one input and one output signal -- Enhanced input digital filters on the input pins for improved noise immunity. -- Identical, orthogonal channels: each channel can perform any time function. Each time function can be assigned to more than one channel at a given time, so each signal can have any functionality. -- Each channel has an event mechanism which supports single and double action functionality in various combinations. It includes two 24-bit capture registers, two 24-bit match registers, 24-bit greater-equal and equal-only comparators -- Input and output signal states visible from the host 2 independent 24-bit time bases for channel synchronization: -- First time base clocked by system clock with programmable prescale division from 2 to 512 (in steps of 2), or by output of second time base prescaler -- Second time base counter can work as a continuous angle counter, enabling angle based applications to match angle instead of time -- Both time bases can be exported to the eMIOS timer module -- Both time bases visible from the host Event-triggered microengine: -- Fixed-length instruction execution in two-system-clock microcycle -- 14 KB of code memory (SCM) -- 3 KB of parameter (data) RAM (SPRAM) -- Parallel execution of data memory, ALU, channel control and flow control sub-instructions in selected combinations MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 17 Overview * * * * * -- 32-bit microengine registers and 24-bit wide ALU, with 1 microcycle addition and subtraction, absolute value, bitwise logical operations on 24-bit, 16-bit, or byte operands, single-bit manipulation, shift operations, sign extension and conditional execution -- Additional 24-bit Multiply/MAC/Divide unit which supports all signed/unsigned Multiply/MAC combinations, and unsigned 24-bit divide. The MAC/Divide unit works in parallel with the regular microcode commands Resource sharing features support channel use of common channel registers, memory and microengine time: -- Hardware scheduler works as a "task management" unit, dispatching event service routines by predefined, host-configured priority -- Automatic channel context switch when a "task switch" occurs, i.e., one function thread ends and another begins to service a request from other channel: channel-specific registers, flags and parameter base address are automatically loaded for the next serviced channel -- SPRAM shared between host CPU and eTPU2, supporting communication either between channels and host or inter-channel -- Dual-parameter coherency hardware support allows atomic access to two parameters by host Test and development support features: -- Nexus Class 1 debug, supporting single-step execution, arbitrary microinstruction execution, hardware breakpoints and watchpoints on several conditions -- Software breakpoints -- SCM continuous signature-check built-in self test (MISC -- multiple input signature calculator), runs concurrently with eTPU2 normal operation System enhancements -- Software watchdog with programmable timeout -- Real-time performance information Channel enhancements -- Channels 1 and 2 can optionally drive angle clock hardware Programming enhancements -- Engine relative addressing mode 2.2.14 eQADC The enhanced queued analog to digital converter (eQADC) block provides accurate and fast conversions for a wide range of applications. The eQADC provides a parallel interface to two on-chip analog to digital converters (ADC), and a single master to single slave serial interface to an off-chip external device. Both on-chip ADCs have access to all the analog channels. The eQADC prioritizes and transfers commands from six command conversion command `queues' to the on-chip ADCs or to the external device. The block can also receive data from the on-chip ADCs or from an off-chip external device into the six result queues, in parallel, independently of the command queues. The six command queues are prioritized with Queue_0 having the highest priority and Queue_5 the lowest. Queue_0 also has the added ability to bypass all buffering and queuing and abort a currently running conversion on either ADC and start a Queue_0 conversion. This means that Queue_0 will always have a deterministic time from trigger to start of conversion, irrespective of what tasks the ADCs were performing when the trigger occurred. The eQADC supports software and external hardware triggers from other blocks to initiate transfers of commands from the queues to the on-chip ADCs or to the external device. It also monitors the fullness of command queues and result queues, and accordingly generates DMA or interrupt requests to control data movement between the queues and the system memory, which is external to the eQADC. The ADCs also support features designed to allow the direct connection of high impedance acoustic sensors that might be used in a system for detecting engine knock. These features include differential inputs; integrated variable gain amplifiers for increasing the dynamic range; programmable pull-up and pull-down resistors for biasing and sensor diagnostics. The eQADC also integrates a programmable decimation filter capable of taking in ADC conversion results at a high rate, passing them through a hardware low pass filter, then down-sampling the output of the filter and feeding the lower sample rate MPC5634M Microcontroller Data Sheet, Rev. 9 18 Freescale Semiconductor Overview results to the result FIFOs. This allows the ADCs to sample the sensor at a rate high enough to avoid aliasing of out-of-band noise; while providing a reduced sample rate output to minimize the amount DSP processing bandwidth required to fully process the digitized waveform. The eQADC provides the following features: * * * * * * * * * Dual on-chip ADCs -- 2 12-bit ADC resolution -- Programmable resolution for increased conversion speed (12 bit, 10 bit, 8 bit) - 12-bit conversion time - 1 s (1M sample/sec) - 10-bit conversion time - 867 ns (1.2M sample/second) - 8-bit conversion time - 733 ns (1.4M sample/second) -- Up to 10-bit accuracy at 500 KSample/s and 9-bit accuracy at 1 MSample/s -- Differential conversions -- Single-ended signal range from 0 to 5 V -- Variable gain amplifiers on differential inputs (1, 2, 4) -- Sample times of 2 (default), 8, 64 or 128 ADC clock cycles -- Provides time stamp information when requested -- Parallel interface to eQADC CFIFOs and RFIFOs -- Supports both right-justified unsigned and signed formats for conversion results Up to 341 input channels (accessible by both ADCs) 23 additional internal channels for measuring control and monitoring voltages inside the device -- Including Core voltage, I/O voltage, LVI voltages, etc. An internal bandgap reference to allow absolute voltage measurements 4 pairs of differential analog input channels -- Programmable pull-up/pull-down resistors on each differential input for biasing and sensor diagnostic (200 k, 100 k, 5 k) Silicon die temperature sensor -- provides temperature of silicon as an analog value -- read using an internal ADC analog channel -- may be read with either ADC Decimation Filter -- Programmable decimation factor (2 to 16) -- Selectable IIR or FIR filter -- Up to 4th order IIR or 8th order FIR -- Programmable coefficients -- Saturated or non-saturated modes -- Programmable Rounding (Convergent; Two's Complement; Truncated) -- Pre-fill mode to pre-condition the filter before the sample window opens Full duplex synchronous serial interface to an external device -- Free-running clock for use by an external device -- Supports a 26-bit message length Priority based Queues -- Supports six Queues with fixed priority. When commands of distinct Queues are bound for the same ADC, the higher priority Queue is always served first 1. 176-pin and 208-pin packages have 34 input channels; 144-pin package has 32. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 19 Overview * * -- Queue_0 can bypass all prioritization, buffering and abort current conversions to start a Queue_0 conversion a deterministic time after the queue trigger -- Streaming mode operation of Queue_0 to execute some commands several times -- Supports software and hardware trigger modes to arm a particular Queue -- Generates interrupt when command coherency is not achieved External hardware triggers -- Supports rising edge, falling edge, high level and low level triggers -- Supports configurable digital filter Supports four external 8-to-1 muxes which can expand the input channels to 56 channels total 2.2.15 DSPI The deserial serial peripheral interface (DSPI) block provides a synchronous serial interface for communication between the MPC5634M MCU and external devices. The DSPI supports pin count reduction through serialization and deserialization of eTPU and eMIOS channels and memory-mapped registers. The channels and register content are transmitted using a SPI-like protocol. This SPI-like protocol is completely configurable for baud rate, polarity and phase, frame length, chip select assertion, etc. Each bit in the frame may be configured to serialize either eTPU channels, eMIOS channels or GPIO signals. The DSPI can be configured to serialize data to an external device that supports the Microsecond Channel protocol. There are two identical DSPI blocks on the MPC5634M MCU. The DSPI output pins support 5 V logic levels or Low Voltage Differential Signalling (LVDS) according to the Microsecond Channel specification. The DSPIs have three configurations: * * * Serial peripheral interface (SPI) configuration where the DSPI operates as an up to 16-bit SPI with support for queues Enhanced deserial serial interface (DSI) configuration where DSPI serializes up to 32 bits with three possible sources per bit -- eTPU, eMIOS, new virtual GPIO registers as possible bit source -- Programmable inter-frame gap in continuous mode -- Bit source selection allows microsecond channel downstream with command or data frames up to 32 bits -- Microsecond channel dual receiver mode Combined serial interface (CSI) configuration where the DSPI operates in both SPI and DSI configurations interleaving DSI frames with SPI frames, giving priority to SPI frames For queued operations, the SPI queues reside in system memory external to the DSPI. Data transfers between the memory and the DSPI FIFOs are accomplished through the use of the eDMA controller or through host software. The DSPI supports these SPI features: * * * * * * * * * Full-duplex, synchronous transfers Selectable LVDS Pads working at 40 MHz for SOUT and SCK pins Master and Slave Mode Buffered transmit operation using the TX FIFO with parameterized depth of 4 entries Buffered receive operation using the RX FIFO with parameterized depth of 4 entries TX and RX FIFOs can be disabled individually for low-latency updates to SPI queues Visibility into the TX and RX FIFOs for ease of debugging FIFO Bypass Mode for low-latency updates to SPI queues Programmable transfer attributes on a per-frame basis: -- Parameterized number of transfer attribute registers (from two to eight) -- Serial clock with programmable polarity and phase -- Various programmable delays: - PCS to SCK delay MPC5634M Microcontroller Data Sheet, Rev. 9 20 Freescale Semiconductor Overview * * * * * * * * - SCK to PCS delay - Delay between frames -- Programmable serial frame size of 4 to 16 bits, expandable with software control -- Continuously held chip select capability 6 Peripheral Chip Selects, expandable to 64 with external demultiplexer Deglitching support for up to 32 Peripheral Chip Selects with external demultiplexer DMA support for adding entries to TX FIFO and removing entries from RX FIFO: -- TX FIFO is not full (TFFF) -- RX FIFO is not empty (RFDF) 6 Interrupt conditions: -- End of queue reached (EOQF) -- TX FIFO is not full (TFFF) -- Transfer of current frame complete (TCF) -- Attempt to transmit with an empty Transmit FIFO (TFUF) -- RX FIFO is not empty (RFDF) -- FIFO Underrun (slave only and SPI mode, the slave is asked to transfer data when the TxFIFO is empty) -- FIFO Overrun (serial frame received while RX FIFO is full) Modified transfer formats for communication with slower peripheral devices Continuous Serial Communications Clock (SCK) Power savings via support for Stop Mode Enhanced DSI logic to implement a 32-bit Timed Serial Bus (TSB) configuration, supporting the Microsecond Channel downstream frame format The DSPIs also support these features unique to the DSI and CSI configurations: * * * * * * * 2 sources of the serialized data: -- eTPU_A and eMIOS output channels -- Memory-mapped register in the DSPI Destinations for the deserialized data: -- eTPU_A and eMIOS input channels -- SIU External Interrupt Request inputs -- Memory-mapped register in the DSPI Deserialized data is provided as Parallel Output signals and as bits in a memory-mapped register Transfer initiation conditions: -- Continuous -- Edge sensitive hardware trigger -- Change in data Pin serialization/deserialization with interleaved SPI frames for control and diagnostics Continuous serial communications clock Support for parallel and serial chaining of up to four DSPI blocks 2.2.16 eSCI The enhanced serial communications interface (eSCI) allows asynchronous serial communications with peripheral devices and other MCUs. It includes special support to interface to Local Interconnect Network (LIN) slave devices. The eSCI block provides the following features: * * Full-duplex operation Standard mark/space non-return-to-zero (NRZ) format MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 21 Overview * * * * * * * * * * * * * 13-bit baud rate selection Programmable 8-bit or 9-bit, data format Programmable 12-bit or 13-bit data format for Timed Serial Bus (TSB) configuration to support the Microsecond Channel upstream Automatic parity generation LIN support -- Autonomous transmission of entire frames -- Configurable to support all revisions of the LIN standard -- Automatic parity bit generation -- Double stop bit after bit error -- 10- or 13-bit break support Separately enabled transmitter and receiver Programmable transmitter output parity 2 receiver wake up methods: -- Idle line wake-up -- Address mark wake-up Interrupt-driven operation with flags Receiver framing error detection Hardware parity checking 1/16 bit-time noise detection DMA support for both transmit and receive data -- Global error bit stored with receive data in system RAM to allow post processing of errors 2.2.17 FlexCAN The MPC5634M MCU contains two controller area network (FlexCAN) blocks. The FlexCAN module is a communication controller implementing the CAN protocol according to Bosch Specification version 2.0B. The CAN protocol was designed to be used primarily as a vehicle serial data bus, meeting the specific requirements of this field: real-time processing, reliable operation in the EMI environment of a vehicle, cost-effectiveness and required bandwidth. FlexCAN module `A' contains 64 message buffers (MB); FlexCAN module `C' contains 32 message buffers. The FlexCAN module provides the following features: * * * * * * * * * * Based on and including all existing features of the Freescale TouCAN module Full Implementation of the CAN protocol specification, Version 2.0B -- Standard data and remote frames -- Extended data and remote frames -- Zero to eight bytes data length -- Programmable bit rate up to 1 Mbit/s Content-related addressing 64 / 32 message buffers of zero to eight bytes data length Individual Rx Mask Register per message buffer Each message buffer configurable as Rx or Tx, all supporting standard and extended messages Includes 1056 / 544 bytes of embedded memory for message buffer storage Includes a 256-byte and a 128-byte memories for storing individual Rx mask registers Full featured Rx FIFO with storage capacity for six frames and internal pointer handling Powerful Rx FIFO ID filtering, capable of matching incoming IDs against 8 extended, 16 standard or 32 partial (8 bits) IDs, with individual masking capability MPC5634M Microcontroller Data Sheet, Rev. 9 22 Freescale Semiconductor Overview * * * * * * * * * * * * * * * Selectable backwards compatibility with previous FlexCAN versions Programmable clock source to the CAN Protocol Interface, either system clock or oscillator clock Listen only mode capability Programmable loop-back mode supporting self-test operation 3 programmable Mask Registers Programmable transmit-first scheme: lowest ID, lowest buffer number or highest priority Time Stamp based on 16-bit free-running timer Global network time, synchronized by a specific message Maskable interrupts Warning interrupts when the Rx and Tx Error Counters reach 96 Independent of the transmission medium (an external transceiver is assumed) Multi master concept High immunity to EMI Short latency time due to an arbitration scheme for high-priority messages Low power mode, with programmable wake-up on bus activity 2.2.18 System timers The system timers provide two distinct types of system timer: * * Periodic interrupts/triggers using the Periodic Interrupt Timer (PIT) Operating system task monitors using the System Timer Module (STM) 2.2.18.1 Periodic Interrupt Timer (PIT) The PIT provides five independent timer channels, capable of producing periodic interrupts and periodic triggers. The PIT has no external input or output pins and is intended to be used to provide system `tick' signals to the operating system, as well as periodic triggers for eQADC queues. Of the five channels in the PIT, four are clocked by the system clock, one is clocked by the crystal clock. This one channel is also referred to as Real Time Interrupt (RTI) and is used to wakeup the device from low power stop mode. The following features are implemented in the PIT: * * * * * * 5 independent timer channels Each channel includes 32-bit wide down counter with automatic reload 4 channels clocked from system clock 1 channel clocked from crystal clock (wake-up timer) Wake-up timer remains active when System STOP mode is entered. Used to restart system clock after predefined timeout period Each channel can optionally generate an interrupt request or a trigger event (to trigger eQADC queues) when the timer reaches zero 2.2.18.2 System Timer Module (STM) The System Timer Module (STM) is designed to implement the software task monitor as defined by AUTOSAR (see http://www.autosar.org). It consists of a single 32-bit counter, clocked by the system clock, and four independent timer comparators. These comparators produce a CPU interrupt when the timer exceeds the programmed value. The following features are implemented in the STM: * * One 32-bit up counter with 8-bit prescaler Four 32-bit compare channels MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 23 Overview * * Independent interrupt source for each channel Counter can be stopped in debug mode 2.2.19 Software Watchdog Timer (SWT) The Software Watchdog Timer (SWT) is a second watchdog module to complement the standard Power Architecture watchdog integrated in the CPU core. The SWT is a 32-bit modulus counter, clocked by the system clock or the crystal clock, that can provide a system reset or interrupt request when the correct software key is not written within the required time window. The following features are implemented: * * * * * * * 32-bit modulus counter Clocked by system clock or crystal clock Optional programmable watchdog window mode Can optionally cause system reset or interrupt request on timeout Reset by writing a software key to memory mapped register Enabled out of reset Configuration is protected by a software key or a write-once register 2.2.20 2.2.20.1 Debug features Nexus port controller The NPC (Nexus Port Controller) block provides real-time development support capabilities for the MPC5634MPower Architecture-based MCU in compliance with the IEEE-ISTO 5001-2003 standard. This development support is supplied for MCUs without requiring external address and data pins for internal visibility. The NPC block is an integration of several individual Nexus blocks that are selected to provide the development support interface for MPC5634M. The NPC block interfaces to the host processor (e200z335), eTPU, and internal buses to provide development support as per the IEEE-ISTO 5001-2003 standard. The development support provided includes program trace and run-time access to the MCUs internal memory map and access to the Power Architecture and eTPU internal registers during halt. The Nexus interface also supports a JTAG only mode using only the JTAG pins. MPC5634Min the production 144 LQFP supports a 3.3 V reduced (4-bit wide) Auxiliary port. These Nexus port pins can also be used as 5 V I/O signals to increase usable I/O count of the device. When using this Nexus port as IO, Nexus trace is still possible using VertiCal calibration. In the VertiCal calibration package, the full 12-bit Auxiliary port is available. NOTE In the VertiCal package, the full Nexus Auxiliary port shares balls with the addresses of the calibration bus. Therefore multiplexed address/data bus mode must be used for the calibration bus when using full width Nexus trace in VertiCal assembly. The following features are implemented: * * 5-pin JTAG port (JCOMP, TDI, TDO, TMS, and TCK) -- Always available in production package -- Supports both JTAG Boundary Scan and debug modes -- 3.3 V interface -- Supports Nexus class 1 features -- Supports Nexus class 3 read/write feature 9-pin Reduced Port interface in 144 LQFP production package -- Alternate function as IO -- 5 V (in GPIO or alternate function mode), 3.3 V (in Nexus mode) interface MPC5634M Microcontroller Data Sheet, Rev. 9 24 Freescale Semiconductor Overview * * -- Auxiliary Output port - 1 MCKO (message clock out) pin - 4 MDO (message data out) pins - 2 MSEO (message start/end out) pins - 1 EVTO (event out) pin -- Auxiliary input port - 1 EVTI (event in) pin 17-pin Full Port interface in calibration package used on VertiCal boards -- 3.3 V interface -- Auxiliary Output port - 1 MCKO (message clock out) pin - 4 (reduced port mode) or 12 (full port mode) MDO (message data out) pins; 8 extra full port pins shared with calibration bus - 2 MSEO (message start/end out) pins - 1 EVTO (event out) pin -- Auxiliary input port - 1 EVTI (event in) pin Host processor (e200) development support features -- IEEE-ISTO 5001-2003 standard class 2 compliant -- Program trace via branch trace messaging (BTM). Branch trace messaging displays program flow discontinuities (direct branches, indirect branches, exceptions, etc.), allowing the development tool to interpolate what transpires between the discontinuities. Thus, static code may be traced. -- Watchpoint trigger enable of program trace messaging -- Data Value Breakpoints (JTAG feature of the e200z335 core): allows CPU to be halted when the CPU writes a specific value to a memory location - 4 data value breakpoints - CPU only - Detects `equal' and `not equal' - Byte, half word, word (naturally aligned) NOTE This feature is imprecise due to CPU pipelining. * * * * -- Subset of Power Architecture software debug facilities with OnCE block (Nexus class 1 features) eTPU development support features -- IEEE-ISTO 5001-2003 standard class 1 compliant for the eTPU -- Nexus based breakpoint configuration and single step support (JTAG feature of the eTPU) Run-time access to the on-chip memory map via the Nexus read/write access protocol. This feature supports accesses for run-time internal visibility, calibration variable acquisition, calibration constant tuning, and external rapid prototyping for powertrain automotive development systems. All features are independently configurable and controllable via the IEEE 1149.1 I/O port Power-on-reset status indication during reset via MDO[0] in disabled and reset modes 2.2.20.2 JTAG The JTAGC (JTAG Controller) block provides the means to test chip functionality and connectivity while remaining transparent to system logic when not in test mode. Testing is performed via a boundary scan technique, as defined in the IEEE 1149.1-2001 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 25 Overview standard. All data input to and output from the JTAGC block is communicated in serial format. The JTAGC block is compliant with the IEEE 1149.1-2001 standard and supports the following features: * * * * * * 2.3 2.3.1 IEEE 1149.1-2001 Test Access Port (TAP) interface 4 pins (TDI, TMS, TCK, and TDO) A 5-bit instruction register that supports the following IEEE 1149.1-2001 defined instructions: -- BYPASS, IDCODE, EXTEST, SAMPLE, SAMPLE/PRELOAD, HIGHZ, CLAMP A 5-bit instruction register that supports the additional following public instructions: -- ACCESS_AUX_TAP_NPC -- ACCESS_AUX_TAP_ONCE -- ACCESS_AUX_TAP_eTPU -- ACCESS_CENSOR 3 test data registers to support JTAG Boundary Scan mode -- Bypass register -- Boundary scan register -- Device identification register A TAP controller state machine that controls the operation of the data registers, instruction register and associated circuitry Censorship Inhibit Register -- 64-bit Censorship password register -- If the external tool writes a 64-bit password that matches the Serial Boot password stored in the internal flash shadow row, Censorship is disabled until the next system reset. MPC5634M series architecture Block diagram Figure 1 shows a top-level block diagram of the MPC5634M series. MPC5634M Microcontroller Data Sheet, Rev. 9 26 Freescale Semiconductor Overview Calibration Bus Interface S e200z335 Nexus Port Nexus NMI eTPU NMI Instructions SPE MMU SIU Nexus 2+ Data M M critical Clocks Interrupt Controller (INTC) CQM PLL STM DMA Requests from Peripheral Blocks PIT SWT Flash 1.5 MB S SRAM 62 KB S S M eDMA Interrupt Requests from Peripheral Blocks & eDMA 3 x 4 64-bit Crossbar Switch JTAG Port 32 KB JTAG Voltage Regulator (1.2V, 3.3V, STB RAM) eDMA, FLASH, Bridge B, crossbar, SRAM Configuration Vstby BAM Peripheral Bridge Nexus SIU Interrupt Request 16 Ch. eMIOS eTPU Reset Control 2x DSPIs 2x eSCIs eQADC 2x CANs ADCI NEXUS 1 External Interrupt Request 32 Ch.+ Engine IMUX ADC ADC RAM 14 KB/3 KB GPIO & Pad Control Serial Analog IF Analog AMUX Decimation Filter ... I/O ... ... ... Temp. Sensor Figure 1. MPC5634M series block diagram 2.3.2 Block summary Table 1 summarizes the functions of the blocks present on the MPC5634M series microcontrollers. Table 1. MPC5634M series block summary Block Function e200z3 core Executes programs and interrupt handlers. Flash memory Provides storage for program code, constants, and variables RAM (random-access memory) Provides storage for program code, constants, and variables Calibration bus Transfers data across the crossbar switch to/from peripherals attached to the VertiCal connector MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 27 Overview Table 1. MPC5634M series block summary (continued) Block Function DMA (direct memory access) Performs complex data movements with minimal intervention from the core DSPI (deserial serial peripheral interface) Provides a synchronous serial interface for communication with external devices eMIOS (enhanced modular input-output system) Provides the functionality to generate or measure events eQADC (enhanced queued analog-to-digital converter) Provides accurate and fast conversions for a wide range of applications eSCI (serial communication interface) Allows asynchronous serial communications with peripheral devices and other microcontroller units eTPU (enhanced time processor unit) Processes real-time input events, performs output waveform generation, and accesses shared data without host intervention FlexCAN (controller area network) Supports the standard CAN communications protocol FMPLL (frequency-modulated phase-locked loop) Generates high-speed system clocks and supports the programmable frequency modulation of these clocks INTC (interrupt controller) Provides priority-based preemptive scheduling of interrupt requests JTAG controller Provides the means to test chip functionality and connectivity while remaining transparent to system logic when not in test mode NPC (Nexus Port Controller) Provides real-time development support capabilities in compliance with the IEEE-ISTO 5001-2003 standard PIT (peripheral interrupt timer) Produces periodic interrupts and triggers Temperature sensor Provides the temperature of the device as an analog value SWT (Software Watchdog Timer) Provides protection from runaway code STM (System Timer Module) Timer providing a set of output compare events to support AutoSAR and operating system tasks MPC5634M Microcontroller Data Sheet, Rev. 9 28 Freescale Semiconductor Pinout and signal description 3 Pinout and signal description This section contains the pinouts for all production packages for the MPC5634M family of devices. Please note the following: * * 3.1 Pins labeled "NC" are to be left unconnected. Any connection to an external circuit or voltage may cause unpredictable device behavior or damage. Pins labeled "NIC" have no internal connection. 144 LQFP pinout Figure 2 shows the pinout for the 144-pin LQFP. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 29 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 AN[21] AN[0] (DAN0+) AN[1] (DAN0-) AN[2] (DAN1+) AN[3] (DAN1-) AN[4] (DAN2+) AN[5] (DAN2-) AN[6] (DAN3+) AN[7] (DAN3-) REFBYPC VRH VRL AN[22] AN[23] AN[24] AN[25] AN[27] AN[28] AN[30] AN[31] AN[32] AN[33] AN[34] AN[35] VDD AN[12] / MA[0] / ETPU_A[19] / SDS AN[13] / MA[1] / ETPU_A[21] / SDO AN[14] / MA[2] / ETPU_A[27] / SDI AN[15] / FCK / ETPU_A[29] VSS MDO[3] / eTPU_A[25] / GPIO[223] VDDEH7 MDO[2] / eTPU_A[21] / GPIO[222] MDO[1] / eTPU_A[19] / GPIO[221] MDO[0] / eTPU_A[13] / GPIO[220] MSEO[0] / eTPU_A[27] / GPIO[224] Pinout and signal description 144-Pin LQFP signal details: pin 14: eTPU_A[31] / DSPI_C_PCS[4] / eTPU_A[13] / GPIO[145] pin 15: eTPU_A[30] / DSPI_C_PCS[3] / eTPU_A[11] / GPIO[144] pin 18: eTPU_A[27] / IRQ[15] / DSPI_C_SOUT_LVDS+ / DSPI_B_SOUT / GPIO[141] pin 19: eTPU_A[26] / IRQ[14] / DSPI_C_SOUT_LVDS- / GPIO[140] pin 20: eTPU_A[25] / IRQ[13] / SCK_C_LVDS+ / GPIO[139] pin 21: eTPU_A[24] / IRQ[12] / SCK_C_LVDS- / GPIO[138] pin 23: eTPU_A[23] / IRQ[11] / eTPU_A[21] / GPIO[137] pin 25: eTPU_A[22] / IRQ[10] / eTPU_A[17] / GPIO[136] pin 35: eTPU_A[14] / DSPI_B_PCS[4] / eTPU_A[9] / GPIO[128] 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 TMS TDI / eMIOS[5] / GPIO[232] EVTO / eTPU_A[4] / GPIO[227] TCK VSS EVTI / eTPU_A[2] / GPIO[231] VDDEH7 MSEO[1] / eTPU_A[29] / GPIO[225] TDO / eMIOS[6] / GPIO[228] MCKO / GPIO[219] JCOMP DSPI_B_PCS[3] / DSPI_C_SIN / GPIO[108] DSPI_B_SOUT / DSPI_C_PCS[5] / GPIO[104] DSPI_B_SIN / DSPI_C_PCS[2] / GPIO[103] DSPI_B_PCS[0] / GPIO[105] VDDEH6B DSPI_B_PCS[1] / GPIO[106] VSS DSPI_B_PCS[2] / DSPI_C_SOUT / GPIO[107] DSPI_B_SCK / DSPI_C_PCS[1] / GPIO[102] DSPI_B_PCS[4] / DSPI_C_SCK / GPIO[109] DSPI_B_PCS[5] / DSPI_C_PCS[0] / GPIO[110] VDD RSTOUT CAN_C_TX / GPIO[87] SCI_A_TX / eMIOS[13] / GPIO[89] SCI_A_RX / eMIOS[15] / GPIO[90] CAN_C_RX / GPIO[88] RESET VSS VDDEH6A VSSPLL XTAL EXTAL / EXTCLK VDDPLL VSS eTPU_A[13] / DSPI_B_PCS[3] / GPIO[127] eTPU_A[12] / DSPI_B_PCS[1] / GPIO[126] eTPU_A[11] / eTPU_A[23] / GPIO[125] eTPU_A[10] / eTPU_A[22] / GPIO[124] eTPU_A[9] / eTPU_A[21] / GPIO[123] eTPU_A[8] / eTPU_A[20] / DSPI_B_SOUT_LVDS+ / GPIO[122] eTPU_A[7] / eTPU_A[19] / DSPI_B_SOUT_LVDS- / eTPU_A[6] / GPIO[121] eTPU_A[6] / eTPU_A[18] / DSPI_B_SCK_LVDS+ / GPIO[120] eTPU_A[5] / eTPU_A[17] / DSPI_B_SCK_LVDS- / GPIO[119] VDDEH1B eTPU_A[4] / eTPU_A[16] / GPIO[118] VSS eTPU_A[3] / eTPU_A[15] / GPIO[117] eTPU_A[2] / eTPU_A[14] / GPIO[116] eTPU_A[1] / eTPU_A[13] / GPIO[115] eTPU_A[0] / eTPU_A[12] / eTPU_A[19] / GPIO[114] VDD eMIOS[0] / eTPU_A[0] / eTPU_A[25] / GPIO[179] eMIOS[2] / eTPU_A[2] / GPIO[181] eMIOS[4] / eTPU_A[4] / GPIO[183] eMIOS[8] / eTPU_A[8] / SCI_B_TX / GPIO[187] eMIOS[9] / eTPU_A[9] / SCI_B_RX / GPIO[188] VSS eMIOS[10] / GPIO[189] VDDEH6A eMIOS[11] / GPIO[190] eMIOS[12] / DSPI_C_SOUT / eTPU_A[27] / GPIO[191] eMIOS[14] / IRQ[0] / eTPU_A[29] / GPIO[193] eMIOS[23] / GPIO[202] CAN_A_TX / SCI_A_TX / GPIO[83] CAN_A_RX / SCI_A_RX / GPIO[84] PLLREF / IRQ[4]/ETRIG[2] / GPIO[208] SCI_B_RX / GPIO[92] BOOTCFG1 / IRQ[3] / ETRIG[3] / GPIO[212] WKPCFG / NMI / DSPI_B_SOUT / GPIO[213] SCI_B_TX / GPIO[91] AN[18] AN[17] AN[16] AN[11] / ANZ AN[9] / ANX VDDA VSSA AN[39] / AN[10] / ANY AN[38] / AN[8] / ANW VDDREG VRCCTL VSTBY VRC33 (see signal details, pin 14) (see signal details, pin 15) eTPU_A[29] / DSPI_C_PCS[2] / GPIO[143] eTPU_A[28] / DSPI_C_PCS[1] / GPIO[142] (see signal details, pin 18) (see signal details, pin 19) (see signal details, pin 20) (see signal details, pin 21) VSS (see signal details, pin 23) VDDEH1A (see signal details, pin 25) VDD eTPU_A[21] / IRQ[9] / GPIO[135] eTPU_A[20] / IRQ[8] / GPIO[134] eTPU_A[19] / GPIO[133] eTPU_A[18] / GPIO[132] eTPU_A[17] / GPIO[131] eTPU_A[16] / GPIO[130] eTPU_A[15] / DSPI_B_PCS[5] / GPIO[129] VDDEH1B (see signal details, pin 35) VSS Figure 2. 144-pin LQFP pinout (top view; all 144-pin devices) 3.2 176 LQFP pinout (MPC5634M) Figure 3 shows the 176-pin LQFP pinout for the MPC5634M (1536 KB flash memory). MPC5634M Microcontroller Data Sheet, Rev. 9 30 Freescale Semiconductor 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 NIC AN[37] AN[36] AN[21] AN[0] (DAN0+) AN[1] (DAN0-) AN[2] (DAN1+) AN[3] (DAN1-) AN[4] (DAN2+) AN[5] (DAN2-) AN[6] (DAN3+) AN[7] (DAN3-) REFBYPC VRH VRL AN[22] AN[23] AN[24] AN[25] AN[27] AN[28] AN[30] AN[31] AN[32] AN[33] AN[34] AN[35] VDD AN[12] / MA[0] / ETPU_A[19] / SDS AN[13] / MA[1] / ETPU_A[21] / SDO AN[14] / MA[2] / ETPU_A[27] / SDI AN[15] / FCK / ETPU_A[29] GPIO[207] GPIO[206] GPIO[99] GPIO[98] VSS eTPU_A[25] / GPIO[223] VDDEH7 eTPU_A[21] / GPIO[222] eTPU_A[19] / GPIO[221] eTPU_A[13] / GPIO[220] eTPU_A[27] / GPIO[224] VSS Pinout and signal description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 176 - Pin LQFP signal details: pin 21: eTPU_A[31] / DSPI_C_PCS[4] / eTPU_A[13] / GPIO[145] pin 22: eTPU_A[30] / DSPI_C_PCS[3] / eTPU_A[11] / GPIO[144] pin 23: eTPU_A[29] / DSPI_C_PCS[2] / GPIO[143] pin 24: eTPU_A[28] / DSPI_C_PCS[1] / GPIO[142] pin 25: eTPU_A[27] / IRQ[15] / DSPI_C_SOUT_LVDS+ / DSPI_B_SOUT / GPIO[141] pin 26: eTPU_A[26] / IRQ[14] / DSPI_C_SOUT_LVDS- / GPIO[140] pin 27: eTPU_A[25] / IRQ[13] / DSPI_C_SCK_LVDS+ / GPIO[139] pin 28: eTPU_A[24] / IRQ[12] / DSPI_C_SCK_LVDS- / GPIO[138] pin 30: eTPU_A[23] / IRQ[11] / eTPU_A[21] / GPIO[137] pin 32: eTPU_A[22] / IRQ[10] / eTPU_A[17] / GPIO[136] pin 40: eTPU_A[15] / DSPI_B_PCS[5] / GPIO[129] pin 42: eTPU_A[14] / DSPI_B_PCS[4] / eTPU_A[9] / GPIO[128] 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 NIC TMS TDI / eMIOS[5] / GPIO[232] eTPU_A[4] / GPIO[227] TCK VSS eTPU_A[2] / GPIO[231] VDDEH7 eTPU_A[29] / GPIO[225] TDO / eMIOS[6] / GPIO[228] GPIO[219] JCOMP ALT_EVTO VDDE12 ALT_MSEO[0] ALT_MSEO[1] ALT_EVTI VSS DSPI_B_PCS[3] / DSPI_C_SIN / GPIO[108] DSPI_B_SOUT / DSPI_C_PCS[5] / GPIO[104] DSPI_B_SIN / DSPI_C_PCS[2] / GPIO[103] DSPI_B_PCS[0] / GPIO[105] VDDEH6B DSPI_B_PCS[1] / GPIO[106] VSS DSPI_B_PCS[2] / DSPI_C_SOUT / GPIO[107] DSPI_B_SCK / DSPI_C_PCS[1] / GPIO[102] DSPI_B_PCS[4] / DSPI_C_SCK / GPIO[109] DSPI_B_PCS[5] / DSPI_C_PCS[0] / GPIO[110] VDD RSTOUT CAN_C_TX / GPIO[87] SCI_A_TX / eMIOS[13] / GPIO[89] SCI_A_RX / eMIOS[15] / GPIO[90] CAN_C_RX / GPIO[88] RESET VSS VDDEH6A VSSPLL XTAL EXTAL / EXTCLK VDDPLL VSS NIC NIC eTPU_A[13] / DSPI_B_PCS[3] / GPIO[127] eTPU_A[12] / DSPI_B_PCS[1] / GPIO[126] eTPU_A[11] / eTPU_A[23] / GPIO[125] eTPU_A[10] / eTPU_A[22] / GPIO[124] eTPU_A[9] / eTPU_A[21] / GPIO[123] eTPU_A[8] / eTPU_A[20] / DSPI_B_SOUT_LVDS+ / GPIO[122] eTPU_A[7] / eTPU_A[19] / DSPI_B_SOUT_LVDS- / eTPU_A[6] / GPIO[121] eTPU_A[6] / eTPU_A[18] / DSPI_B_SCK_LVDS+ / GPIO[120] eTPU_A[5] / eTPU_A[17] / DSPI_B_SCK_LVDS- / GPIO[119] VDDEH1B eTPU_A[4] / eTPU_A[16] / GPIO[118] VSS eTPU_A[3] / eTPU_A[15] / GPIO[117] eTPU_A[2] / eTPU_A[14] / GPIO[116] eTPU_A[1] / eTPU_A[13] / GPIO[115] eTPU_A[0] / eTPU_A[12] / eTPU_A[19] / GPIO[114] VDD eMIOS[0] / eTPU_A[0] / eTPU_A[25] / GPIO[179] eMIOS[1] / eTPU_A[1] / GPIO[180] eMIOS[2] / eTPU_A[2] / GPIO[181] NIC eMIOS[4] / eTPU_A[4] / GPIO[183] NIC NIC eMIOS[8] / eTPU_A[8] / SCI_B_TX / GPIO[187] eMIOS[9] / eTPU_A[9] / SCI_B_RX / GPIO[188] VSS eMIOS[10] / GPIO[189] VDDEH6A eMIOS[11] / GPIO[190] eMIOS[12] / DSPI_C_SOUT / eTPU_A[27] / GPIO[191] eMIOS[13] / GPIO[192] eMIOS[14] / IRQ[0] / eTPU_A[29] / GPIO[193] eMIOS[15] / IRQ[1] / GPIO[194] eMIOS[23] / GPIO[202] CAN_A_TX / SCI_A_TX / GPIO[83] CAN_A_RX / SCI_A_RX / GPIO[84 PLLREF / IRQ[4]/ETRIG[2] / GPIO[208] SCI_B_RX / GPIO[92] BOOTCFG1 / IRQ[3] / ETRIG[3] / GPIO[212] WKPCFG / NMI / DSPI_B_SOUT / GPIO[213] SCI_B_TX / GPIO[91] NIC 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 AN[18] AN[17] AN[16] AN[11] / ANZ AN[9] / ANX VDDA VSSA AN[39] / AN[10] / ANY AN[38] / AN[8] / ANW VDDREG VRCCTL VSTBY VRC33 ALT_MCKO VSS VDDE12 ALT_MDO[0] ALT_MDO[1] ALT_MDO[2] ALT_MDO[3] (see signal details, pin 21) (see signal details, pin 22) (see signal details, pin 23) (see signal details, pin 24) (see signal details, pin 25) (see signal details, pin 26) (see signal details, pin 27) (see signal details, pin 28) VSS (see signal details, pin 30) VDDEH1A (see signal details, pin 32) VDD eTPU_A[21] / IRQ[9] / GPIO[135] eTPU_A[20] / IRQ[8] / GPIO[134] eTPU_A[19] / GPIO[133] eTPU_A[18] / GPIO[132] eTPU_A[17] / GPIO[131] eTPU_A[16] / GPIO[130] (see signal details, pin 40) VDDEH1B (see signal details, pin 42) VSS NIC Note: Pins marked "NIC" have no internal connection. Figure 3. 176-pin LQFP pinout (MPC5634M; top view) MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 31 Pinout and signal description 3.3 176 LQFP pinout (MPC5633M) 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 NIC NC NC AN[21] AN[0] (DAN0+) AN[1] (DAN0-) AN[2] (DAN1+) AN[3] (DAN1-) AN[4] (DAN2+) AN[5] (DAN2-) AN[6] (DAN3+) AN[7] (DAN3-) REFBYPC VRH VRL AN[22] AN[23] AN[24] AN[25] AN[27] AN[28] AN[30] AN[31] AN[32] AN[33] AN[34] AN[35] VDD AN[12] / MA[0] / ETPU_A[19] / SDS AN[13] / MA[1] / ETPU_A[21] / SDO AN[14] / MA[2] / ETPU_A[27] / SDI AN[15] / FCK / ETPU_A[29] NC NC NC NC VSS eTPU_A[25] / GPIO[223] VDDEH7 eTPU_A[21] / GPIO[222] eTPU_A[19] / GPIO[221] eTPU_A[13] / GPIO[220] eTPU_A[27] / GPIO[224] VSS Figure 4 shows the pinout for the 176-pin LQFP for the MPC5633M (1024 KB flash memory). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 176-Pin LQFP signal details: Pin 21: eTPU_A[31] / DSPI_C_PCS[4] / eTPU_A[13] / GPIO[145] Pin 22: eTPU_A[30] / DSPI_C_PCS[3] / eTPU_A[11] / GPIO[144] Pin 23: eTPU_A[29] / DSPI_C_PCS[2] / GPIO[143] Pin 24: eTPU_A[28]/ DSPI_C_PCS[1] / GPIO[142] Pin 25: eTPU_A[27] / IRQ[15] / DSPI_C_SOUT_LVDS+ / DSPI_B_SOUT / GPIO[141] Pin 26: eTPU_A[26] / IRQ[14] / DSPI_C_SOUT_LVDS- / GPIO[140] Pin 27: eTPU_A[25] / IRQ[13] / DSPI_C_SCK_LVDS+ / GPIO[139] Pin 28: eTPU_A[24] / IRQ[12] / DSPI_C_SCK_LVDS- / GPIO[138] Pin 30: eTPU_A[23] / IRQ[11] / eTPU_A[21] / GPIO[137] Pin 32: eTPU_A[22] / IRQ[10] / eTPU_A[17] / GPIO[136] Pin 40: eTPU_A[15] / DSPI_B_PCS[5] / GPIO[129] Pin 42: eTPU_A[14] / DSPI_B_PCS[4] / eTPU_A[9] / GPIO[128] 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 NIC TMS TDI / eMIOS[5] / GPIO[232] eTPU_A[4] / GPIO[227] TCK VSS eTPU_A[2] / GPIO[231] VDDEH7 eTPU_A[29] / GPIO[225] TDO / eMIOS[6] / GPIO[228] GPIO[219] JCOMP ALT_EVTO VDDE12 ALT_MSEO[0] ALT_MSEO[1] ALT_EVTI VSS DSPI_B_PCS[3] / DSPI_C_SIN / GPIO[108] DSPI_B_SOUT / DSPI_C_PCS[5] / GPIO[104] DSPI_B_SIN / DSPI_C_PCS[2] / GPIO[103] DSPI_B_PCS[0] / GPIO[105] VDDEH6B DSPI_B_PCS[1] / GPIO[106] VSS DSPI_B_PCS[2] / DSPI_C_SOUT / GPIO[107] DSPI_B_SCK / DSPI_C_PCS[1] / GPIO[102] DSPI_B_PCS[4] / DSPI_C_SCK / GPIO[109] DSPI_B_PCS[5] / DSPI_C_PCS[0] / GPIO[110] VDD RSTOUT CAN_C_TX / GPIO[87] SCI_A_TX / eMIOS[13] / GPIO[89] SCI_A_RX / eMIOS[15] / GPIO[90] CAN_C_RX / GPIO[88] RESET VSS VDDEH6A VSSPLL XTAL EXTAL / EXTCLK VDDPLL VSS NIC NIC eTPU_A[13] / DSPI_B_PCS[3] / GPIO[127] eTPU_A[12] / DSPI_B_PCS[1] / GPIO[126] eTPU_A[11] / eTPU_A[23] / GPIO[125] eTPU_A[10] / eTPU_A[22] / GPIO[124] eTPU_A[9] / eTPU_A[21] / GPIO[123] eTPU_A[8]/eTPU_A[20]/DSPI_B_SOUT_LVDS+/GPIO[122] eTPU_A[7]/eTPU_A[19]/DSPI_B_SOUT_LVDS-/eTPU_A[6]/GPIO[121] eTPU_A[6] / eTPU_A[18] / DSPI_B_SCK_LVDS+ / GPIO[120] eTPU_A[5] / eTPU_A[17] / DSPI_B_SCK_LVDS- / GPIO[119] VDDEH1B eTPU_A[4] / eTPU_A[16] / GPIO[118] VSS eTPU_A[3] / eTPU_A[15] / GPIO[117] eTPU_A[2] / eTPU_A[14] / GPIO[116] eTPU_A[1] / eTPU_A[13] / GPIO[115] eTPU_A[0] / eTPU_A[12] / eTPU_A[19] / GPIO[114] VDD eMIOS[0] / eTPU_A[0] / eTPU_A[25] / GPIO[179] NC eMIOS[2] / eTPU_A[2] / GPIO[181] NIC eMIOS[4] / eTPU_A[4] / GPIO[183] NIC NIC eMIOS[8] / eTPU_A[8] / SCI_B_TX / GPIO[187] eMIOS[9] / eTPU_A[9] / SCI_B_RX / GPIO[188] VSS eMIOS[10] / GPIO[189] VDDEH6A eMIOS[11] / GPIO[190] eMIOS[12] / DSPI_C_SOUT / eTPU_A[27] / GPIO[191] NC eMIOS[14] / IRQ[0] / eTPU_A[29] / GPIO[193] NC eMIOS[23] / GPIO[202] CAN_A_TX / SCI_A_TX / GPIO[83] CAN_A_RX / SCI_A_RX / GPIO[84] PLLREF / IRQ[4]/ETRIG[2] / GPIO[208] SCI_B_RX / GPIO[92] BOOTCFG1 / IRQ[3] / ETRIG[3] / GPIO[212] WKPCFG / NMI / DSPI_B_SOUT / GPIO[213] SCI_B_TX / GPIO[91] NIC 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 AN[18] AN[17] AN[16] AN[11] / ANZ AN[9] / ANX VDDA VSSA AN[39] / AN[10] / ANY AN[38] / AN[8] / ANW VDDREG VRCCTL VSTBY VRC33 ALT_MCKO VSS VDDE12 ALT_MDO[0] ALT_MDO[1] ALT_MDO[2] ALT_MDO[3] (see signal details, pin 21) (see signal details, pin 22) (see signal details, pin 23) (see signal details, pin 24) (see signal details, pin 25) (see signal details, pin 26) (see signal details, pin 27) (see signal details, pin 28) VSS (see signal details, pin 30) VDDEH1A (see signal details, pin 32) VDD eTPU_A[21] / IRQ[9] / GPIO[135] eTPU_A[20] / IRQ[8] / GPIO[134] eTPU_A[19] / GPIO[133] eTPU_A[18] / GPIO[132] eTPU_A[17] / GPIO[131] eTPU_A[16] / GPIO[130] (see signal details, pin 40) VDDEH1B (see signal details, pin 42) VSS NIC Notes: 1. Pins marked "NIC" have no internal connection. 2. Pins marked "NC" are not functional pins but may be connected to internal circuitry. Connections to external circuits or other pins on this device can result in unpredictable system behavior or damage. Figure 4. 176-pin LQFP pinout (MPC5633M; top view) MPC5634M Microcontroller Data Sheet, Rev. 9 32 Freescale Semiconductor Freescale Semiconductor 3.4 208 MAPBGA ballmap (MPC5634M) Figure 5 shows the 208-pin MAPBGA ballmap for the MPC5634M (1536 KB flash memory) as viewed from above. MPC5634M Microcontroller Data Sheet, Rev. 9 3 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A VSS AN9 AN11 VDDA1 VSSA1 AN1 AN5 VRH VRL AN27 VSSA0 AN12- SDS ALT_ MDO2 ALT_ MDO0 VRC33 VSS B VDD VSS AN38 AN21 AN0 AN4 REFBYPC AN22 AN25 AN28 VDDA0 AN13-SDO ALT_ MDO3 ALT_ MDO1 VSS VDD C VSTBY VDD VSS AN17 AN34 AN16 AN3 AN7 AN23 AN32 AN33 AN14-SDI AN15 FCK VSS ALT_ MSEO0 TCK D VRC33 AN39 VDD VSS AN18 AN2 AN6 AN24 AN30 AN31 AN35 VDDEH7 VSS TMS ALT_EVTO NIC1 E ETPUA30 ETPUA31 AN37 VDD VDDE7 TDI ALT_EVTI ALT_ MSEO1 F ETPUA28 ETPUA29 ETPUA26 AN36 VDDEH6 TDO ALT_MCKO JCOMP G ETPUA24 ETPUA27 ETPUA25 ETPUA21 VSS VSS VSS VSS DSPI_B_ SOUT DSPI_B_ PCS3 DSPI_B_ SIN DSPI_B_ PCS0 H ETPUA23 ETPUA22 ETPUA17 ETPUA18 VSS VSS VSS VSS GPIO99 DSPI_B_ PCS4 DSPI_B_ PCS2 DSPI_B_ PCS1 J ETPUA20 ETPUA19 ETPUA14 ETPUA13 VSS VSS VSS VSS DSPI_B_ PCS5 SCI_A_TX GPIO98 DSPI_B_ SCK K ETPUA16 ETPUA15 ETPUA7 VDDEH1 VSS VSS VSS VSS CAN_C_ TX SCI_A_RX RSTOUT VDDREG L ETPUA12 ETPUA11 ETPUA6 ETPUA0 SCI_B_TX CAN_C_ RX WKPCFG M ETPUA10 ETPUA9 ETPUA1 ETPUA5 SCI_B_RX PLLREF BOOTCFG1 VSSPLL N ETPUA8 ETPUA4 ETPUA0 VSS VDD VRC33 EMIOS2 EMIOS10 VDDEH1/62 EMIOS12 eTPU_A193 VRC33 VSS VRCCTL NIC1 EXTAL P ETPUA3 ETPUA2 VSS VDD GPIO207 VDDE7 NIC1 EMIOS8 eTPU_A293 eTPU_A23 eTPU_A213 CAN_A_ TX VDD VSS NIC1 XTAL R NIC1 VSS VDD GPIO206 EMIOS4 NIC1 EMIOS9 EMIOS11 EMIOS14 eTPU_A273 EMIOS23 CAN_A_ RX NIC1 VDD VSS VDDPLL T VSS VDD NIC1 EMIOS0 EMIOS1 GPIO219 eTPU_A253 EMIOS13 EMIOS15 eTPU_A43 eTPU_A133 NIC1 VDDE5 CLKOUT VDD VSS Pins marked "NIC" have no internal connection. This ball may be changed to "NC" (no connection) in a future revision. eTPU output only channel. Figure 5. 208-pin MAPBGA ballmap (MPC5634M; top view) RESET 33 Pinout and signal description 1 2 1 208 MAPBGA ballmap (MPC5633M only) Figure 6 shows the 208-pin MAPBGA ballmap for the MPC5633M (1024 KB flash memory) as viewed from above. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A VSS AN9 AN11 VDDA1 VSSA1 AN1 AN5 VRH VRL AN27 VSSA0 AN12-SDS ALT_ MDO2 ALT_ MDO0 VRC33 VSS B VDD VSS AN38 AN21 AN0 AN4 REFBYPC AN22 AN25 AN28 VDDA0 AN13-SDO ALT_ MDO3 ALT_ MDO1 VSS VDD C VSTBY VDD VSS AN17 AN34 AN16 AN3 AN7 AN23 AN32 AN33 AN14-SDI AN15 FCK VSS ALT_ MSEO0 TCK D VRC33 AN39 VDD VSS AN18 AN2 AN6 AN24 AN30 AN31 AN35 VDDEH7 VSS TMS ALT_EVTO NIC1 E ETPUA30 ETPUA31 NC2 VDD VDDE7 TDI ALT_ EVTI ALT_ MSEO1 F ETPUA28 ETPUA29 ETPUA26 NC2 VDDEH6 TDO ALT_MCKO JCOMP G ETPUA24 ETPUA27 ETPUA25 ETPUA21 VSS VSS VSS VSS DSPI_B_ SOUT DSPI_B_ PCS3 DSPI_B_ SIN DSPI_B_ PCS0 H ETPUA23 ETPUA22 ETPUA17 ETPUA18 VSS VSS VSS VSS NC2 DSPI_B_ PCS4 DSPI_B_ PCS2 DSPI_B_ PCS1 J ETPUA20 ETPUA19 ETPUA14 ETPUA13 VSS VSS VSS VSS DSPI_B_ PCS5 SCI_A_TX NC2 DSPI_B_ SCK K ETPUA16 ETPUA15 ETPUA7 VDDEH1 VSS VSS VSS VSS CAN_C_ TX SCI_A_RX RSTOUT VDDREG L ETPUA12 ETPUA11 ETPUA6 ETPUA0 SCI_B_TX CAN_C_ RX WKPCFG RESET M ETPUA10 ETPUA9 ETPUA1 ETPUA5 SCI_B_RX PLLREF BOOTCFG1 VSSPLL N ETPUA8 ETPUA4 ETPUA0 VSS VDD VRC33 EMIOS2 EMIOS10 P ETPUA3 ETPUA2 VSS VDD NC2 VDDE7 NIC1 EMIOS8 R NIC1 VSS VDD NC2 EMIOS4 NIC1 EMIOS9 EMIOS11 EMIOS14 T VSS VDD NIC1 EMIOS0 NC2 GPIO219 eTPUA253 NC2 NC2 VDDEH1/63 EMIOS12 eTPUA293 eTPUA23 eTPUA273 eTPUA43 eTPUA194 VRC33 VSS VRCCTL NIC1 EXTAL eTPUA213 CAN_A_ TX VDD VSS NIC1 XTAL EMIOS23 CAN_A_ RX NC2 VDD VSS VDDPLL eTPUA133 NIC1 VDDE5 CLKOUT VDD VSS Pins marked "NIC" have no internal connection. Pins marked "NC" may be connected to internal circuitry. Connections to external circuits or other pins on this device can result in unpredictable system behavior or damage. This ball may be changed to "NC" (no connection) in a future revision. eTPU output only channel. Figure 6. 208-pin MAPBGA ballmap (MPC5633M; top view) Pinout and signal description 34 3.5 Signal summary t Table 2. MPC563xM signal properties 1 Name Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA Dedicated GPIO MPC5634M Microcontroller Data Sheet, Rev. 9 GPIO[98] GPIO PCR[98] -- I/O VDDEH7 Slow - / Up GPIO[98]/Up -- 1417 J158 GPIO[99] GPIO PCR[99] -- I/O VDDEH7 Slow - / Up GPIO[99]/Up -- 1427 H138 GPIO[206]9 GPIO PCR[206] -- I/O VDDEH7 Slow - / Up GPIO[206]/Up -- 1437 R48 GPIO[207]9 GPIO PCR[207] -- I/O VDDEH7 Slow - / Up GPIO[207]/Up -- 1447 P58 Reset / Configuration Freescale Semiconductor RESET External Reset Input RSTOUT External Reset Output PLLREF IRQ[4] ETRIG[2] GPIO[208] FMPLL Mode Selection External Interrupt Request eQADC Trigger Input GPIO BOOTCFG1 IRQ[3] ETRIG[3] GPIO[212] WKPCFG NMI DSPI_B_SOUT GPIO[213] -- -- I VDDEH6a Slow I / Up RESET / Up 80 97 L16 PCR[230] -- O VDDEH6a Slow RSTOUT/ Low RSTOUT/ High 85 102 K15 PCR[208] 011 010 100 000 I I I I/O VDDEH6a Slow PLLREF / Up - / Up 68 83 M14 Boot Config. Input External Interrupt Request eQADC Trigger Input GPIO PCR[212] 011 010 100 000 I I I I/O VDDEH6a Slow BOOTCFG1 / Down - / Down 70 85 M15 Weak Pull Config. Input Non-Maskable Interrupt DSPI_B Data Output GPIO PCR[213] 01 11 10 00 I I O I/O VDDEH6a Slow WKPCFG / Up - / Up 71 86 L15 O / Low CAL_ADDR / Low -- -- -- Calibration10 CAL_ADDR[12:15]11 Calibration Address Bus PCR[340] -- O VDDE12 Fast Pinout and signal description 35 3.6 Freescale Semiconductor Table 2. MPC563xM signal properties (continued) Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 Calibration Address Bus Nexus Msg Data Out PCR[345] -- O O VDDE1213 VDDE714 Fast O / Low15 MDO / ALT_ADDR12 / Low -- 17 A14 CAL_ADDR[17]21 ALT_MDO[1]12 Calibration Address Bus Nexus Msg Data Out PCR[345] -- O O VDDE1213 VDDE714 Fast O / Low15 ALT_MDO / CAL_ADDR12 / Low -- 18 B14 CAL_ADDR[18]21 ALT_MDO[2]12 Calibration Address Bus Nexus Msg Data Out PCR[345] -- O O VDDE1213 VDDE714 Fast O / Low15 ALT_MDO / CAL_ADDR12 / Low -- 19 A13 CAL_ADDR[19]21 ALT_MDO[3]12 Calibration Address Bus Nexus Msg Data Out PCR[345] -- O O VDDE1213 VDDE714 Fast O / Low15 ALT_MDO / CAL_ADDR12 / Low -- 20 B13 CAL_ADDR[20:27] ALT_MDO[4:11] Calibration Address Bus Nexus Msg Data Out PCR[345] -- O O VDDE1213 Fast O / Low ALT_MDO / CAL_ADDR16 / Low -- -- -- CAL_ADDR[28]21 ALT_MSEO[0]12 Calibration Address Bus Nexus Msg Start/End Out PCR[345] -- O O VDDE1213 VDDE714 Fast O / Low17 ALT_MSEO16 / CAL_ADDR17/ Low -- 118 C15 CAL_ADDR[29]21 ALT_MSEO[1]12 Calibration Address Bus Nexus Msg Start/End Out PCR[345] -- O O VDDE1213 VDDE714 Fast O / Low17 ALT_MSEO16 / CAL_ADDR17/ Low -- 117 E16 CAL_ADDR[30]21 ALT_EVTI12 Calibration Address Bus Nexus Event In PCR[345] -- O I VDDE1213 VDDE714 Fast --18 ALT_EVTI / CAL_ADDR19 -- 116 E15 ALT_EVTO Nexus Event Out PCR[344] -- O VDDE1213 VDDE714 Fast O / Low ALT_EVTO / High -- 120 D15 ALT_MCKO Nexus Msg Clock Out PCR[344] -- O VDDE1213 VDDE714 Fast O / Low ALT_MCKO / Enabled -- 14 F15 NEXUSCFG11 Nexus/Calibration bus selector -- I VDDE12 Fast I / Down NEXUSCFG / Down -- -- -- CAL_CS[0]11 Calibration Chip Selects PCR[336] -- O VDDE12 Fast O / High CAL_CS / High -- -- -- CAL_CS[2]11 CAL_ADDR[10] Calibration Chip Selects Calibration Address Bus PCR[338] 11 10 O O VDDE12 Fast O / High CAL_CS / High -- -- -- -- Pinout and signal description 36 CAL_ADDR[16]21 ALT_MDO[0]12 Name 1 Function Pad Config. Register (PCR)2 Pin No. PCR PA Field3 I/O Type Voltage4 / Pad Type 11 10 O O VDDE12 Fast O / High Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA CAL_CS / High -- -- -- MPC5634M Microcontroller Data Sheet, Rev. 9 CAL_CS[3]11 CAL_ADDR[11] Calibration Chip Selects Calibration Address Bus PCR[339] CAL_DATA[0:9]11 Calibration Data Bus PCR[341] I/O VDDE12 Fast - / Up - / Up -- -- -- CAL_DATA[10:15]11 Calibration Data Bus PCR[341] I/O VDDE12 Fast - / Up - / Up -- -- -- CAL_OE11 Calibration Output Enable PCR[342] -- O VDDE12 Fast O / High CAL_OE / High -- -- -- CAL_RD_WR11 Calibration Read/Write PCR[342] -- O VDDE12 Fast O / High CAL_RD_WR /High -- -- -- CAL_TS_ALE11 Calibration Transfer Start Address Latch Enable PCR[343] TS=0b1 ALE=0b0 O O VDDE12 Fast O / High CAL_TS / High -- -- -- CAL_WE_BE[0:1]11 Calibration Write Enable Byte Enable PCR[342] -- O VDDE12 Fast O / High CAL_WE / High -- -- -- NEXUS20 Freescale Semiconductor EVTI21 eTPU_A[2] GPIO[231] Nexus Event In eTPU A Ch. GPIO PCR[231] 01 10 00 I O I/O VDDEH7 Multi-V -/- -/- 103 126 P10 EVTO 21 eTPU_A[4] GPIO[227] Nexus Event Out eTPU A Ch. GPIO PCR[227] 0122 10 00 O O I/O VDDEH7 Multi-V I / Up I / Up 106 129 T10 MCKO21 GPIO[219] Nexus Msg Clock Out GPIO PCR[219] N/A22 00 O I/O VDDEH7 Multi-V -/- -/- 99 122 T6 MDO[0]21 eTPU_A[13] GPIO[220] Nexus Msg Data Out eTPU A Ch. GPIO PCR[220] 01 10 00 O O I/O VDDEH7 Multi-V -/- -/- 110 135 T11 MDO[1]21 eTPU_A[19] GPIO[221] Nexus Msg Data Out eTPU A Ch. GPIO PCR[221] 0122 10 00 O O I/O VDDEH7 Multi-V -/- -/- 111 136 N11 MDO[2]21 eTPU_A[21] GPIO[222] Nexus Msg Data Out eTPU A Ch. GPIO PCR[222] 0122 10 00 O O I/O VDDEH7 Multi-V -/- -/- 112 137 P11 Pinout and signal description 37 Table 2. MPC563xM signal properties (continued) Freescale Semiconductor Table 2. MPC563xM signal properties (continued) Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 MDO[3]21 eTPU_A[25] GPIO[223] Nexus Msg Data Out eTPU A Ch. GPIO PCR[223] 0122 10 00 O O I/O VDDEH7 Multi-V -/- -/- 114 139 T7 MSEO[0]21 eTPU_A[27] GPIO[224] Nexus Msg Start/End Out eTPU A Ch. GPIO PCR[224] 0122 10 00 O O I/O VDDEH7 Multi-V -/- -/- 109 134 R10 MSEO[1]21 eTPU_A[29] GPIO[225] Nexus Msg Start/End Out eTPU A Ch. GPIO PCR[225] 0122 10 00 O O I/O VDDEH7 Multi-V -/- -/- 101 124 P9 JTAG / TEST TCK JTAG Test Clock Input TDI23 eMIOS[5] GPIO[232] JTAG Test Data Input eMIOS Ch. GPIO TDO23 eMIOS[6] GPIO[228] JTAG Test Data Output eMIOS Ch. GPIO TMS JTAG Test Mode Select Input JCOMP JTAG TAP Controller Enable -- -- I VDDEH7 Multi-V TCK / Down TCK / Down 105 128 C16 PCR[232] 0124 10 00 I O I/O VDDEH7 Multi-V -/- -/- 107 130 E14 PCR[228] 0124 10 00 O O I/O VDDEH7 Multi-V -/- -/- 100 123 F14 -- -- I VDDEH7 Multi-V TMS / Up TMS / Up 108 131 D14 -- -- I VDDEH7 Multi-V JCOMP / Down JCOMP / Down 98 121 F16 CAN CAN_A Transmit eSCI_A Transmit GPIO PCR[83] 01 10 00 O O I/O VDDEH6a Slow - / Up - / Up25 66 81 P12 CAN_A_RX SCI_A_RX GPIO[84] CAN_A Receive eSCI_A Receive GPIO PCR[84] 01 10 00 I I I/O VDDEH6a Slow - / Up - / Up 67 82 R12 CAN_C_TX GPIO[87] CAN_C Transmit GPIO PCR[87] 01 00 O I/O VDDEH6a Medium - / Up - / Up 84 101 K13 CAN_C_RX GPIO[88] CAN_C Receive GPIO PCR[88] 01 00 I I/O VDDEH6a Slow - / Up - / Up 81 98 L14 38 Pinout and signal description CAN_A_TX SCI_A_TX GPIO[83] Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA eSCI MPC5634M Microcontroller Data Sheet, Rev. 9 SCI_A_TX eMIOS[13] GPIO[89] eSCI_A Transmit eMIOS Ch. GPIO PCR[89] 01 10 00 O O I/O VDDEH6a Slow - / Up - / Up 83 100 J14 SCI_A_RX26 eMIOS[15] GPIO[90] eSCI_A Receive eMIOS Ch. GPIO PCR[90] 01 10 00 I O I/O VDDEH6a Slow - / Up - / Up 82 99 K14 SCI_B_TX GPIO[91] eSCI_B Transmit GPIO PCR[91] 01 00 I/O I/O VDDEH6a Slow - / Up - / Up 72 87 L13 SCI_B_RX GPIO[92] eSCI_B Receive GPIO PCR[92] 01 00 I I/O VDDEH6a Slow - / Up - / Up 69 84 M13 DSPI Freescale Semiconductor DSPI_B_SCK DSPI_C_PCS[1] GPIO[102] DSPI_B Clock DSPI_C Periph Chip Select GPIO PCR[102] 01 10 00 I/O O I/O VDDEH6b Medium - / Up - / Up 89 106 J16 DSPI_B_SIN DSPI_C_PCS[2] GPIO[103] DSPI_B Data Input DSPI_C Periph Chip Select GPIO PCR[103] 01 10 00 I O I/O VDDEH6b Medium - / Up - / Up 95 112 G15 DSPI_B_SOUT DSPI_C_PCS[5] GPIO[104] DSPI_B Data Output DSPI_C Periph Chip Select GPIO PCR[104] 01 10 00 O O I/O VDDEH6b Medium - / Up - / Up 96 113 G13 DSPI_B_PCS[0] GPIO[105] DSPI_B Periph Chip Select GPIO PCR[105] 01 00 O I/O VDDEH6b Medium - / Up - / Up 94 111 G16 DSPI_B_PCS[1] GPIO[106] DSPI_B Periph Chip Select GPIO PCR[106] 01 00 O I/O VDDEH6b Medium - / Up - / Up 92 109 H16 DSPI_B_PCS[2] DSPI_C_SOUT GPIO[107] DSPI_B Periph Chip Select DSPI_C Data Output GPIO PCR[107] 01 10 00 O O I/O VDDEH6b Medium - / Up - / Up 90 107 H15 DSPI_B_PCS[3] DSPI_C_SIN GPIO[108] DSPI_B Periph Chip Select DSPI_C Data Input GPIO PCR[108] 01 10 00 O I I/O VDDEH6b Medium - / Up - / Up 97 114 G14 DSPI_B_PCS[4] DSPI_C_SCK GPIO[109] DSPI_B Periph Chip Select DSPI_C Clock GPIO PCR[109] 01 10 00 O I/O I/O VDDEH6b Medium - / Up - / Up 88 105 H14 Pinout and signal description 39 Table 2. MPC563xM signal properties (continued) Freescale Semiconductor Table 2. MPC563xM signal properties (continued) Name DSPI_B_PCS[5] DSPI_C_PCS[0] GPIO[110] 1 Function DSPI_B Periph Chip Select DSPI_C Periph Chip Select GPIO Pad Config. Register (PCR)2 PCR[110] PCR PA Field3 I/O Type Voltage4 / Pad Type 01 10 00 O O I/O VDDEH6b Medium Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA - / Up - / Up 87 104 J13 eQADC MPC5634M Microcontroller Data Sheet, Rev. 9 Single Ended Analog Input Positive Terminal Diff. Input -- -- I I VDDA I/- AN[0] / - 143 172 B5 AN[1]27 DAN0- Single Ended Analog Input Negative Terminal Diff. Input -- -- I I VDDA I/- AN[1] / - 142 171 A6 AN[2]27 DAN1+ Single Ended Analog Input Positive Terminal Diff. Input -- -- I I VDDA I/- AN[2] / - 141 170 D6 AN[3]27 DAN1- Single Ended Analog Input Negative Terminal Diff. Input -- -- I I VDDA I/- AN[3] / - 140 169 C7 AN[4]27 DAN2+ Single Ended Analog Input Positive Terminal Diff. Input -- -- I I VDDA I/- AN[4] / - 139 168 B6 AN[5]27 DAN2- Single Ended Analog Input Negative Terminal Diff. Input -- -- I I VDDA I/- AN[5] / - 138 167 A7 AN[6]27 DAN3+ Single Ended Analog Input Positive Terminal Diff. Input -- -- I I VDDA I/- AN[6] / - 137 166 D7 AN[7]27 DAN3- Single Ended Analog Input Negative Terminal Diff. Input -- -- I I VDDA I/- AN[7] / - 136 165 C8 AN[8] See AN[38]-AN[8]-ANW AN[9] ANX Single Ended Analog Input External Multiplexed Analog Input -- -- I I VDDA I/- AN[9] / - 5 5 A2 AN[10] See AN[39]-AN[10]-ANY AN[11] ANZ Single Ended Analog Input External Multiplexed Analog Input -- -- I I VDDA I/- AN[11] / - 4 4 A3 AN[12] MA[0] ETPU_A[19] SDS Single Ended Analog Input Mux Address ETPU_A Ch. eQADC Serial Data Strobe 011 010 100 000 I O O O VDDEH7 I/- AN[12] / - 119 148 A12 PCR[215] 40 Pinout and signal description AN[0]27 DAN0+ Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor AN[13] MA[1] ETPU_A[21] SDO Single Ended Analog Input Mux Address ETPU_A Ch. eQADC Serial Data Out PCR[216] 011 010 100 000 I O O O VDDEH7 I/- AN[13] / - 118 147 B12 AN[14] MA[2] ETPU_A[27] SDI Single Ended Analog Input Mux Address ETPU_A Ch. eQADC Serial Data In PCR[217] 011 010 100 000 I O O I VDDEH7 I/- AN[14] / - 117 146 C12 AN[15] FCK ETPU_A[29] Single Ended Analog Input eQADC Free Running Clock ETPU_A Ch. PCR[218] 011 010 000 I O O VDDEH7 I/- AN[15] / - 116 145 C13 AN[16] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 3 3 C6 AN[17] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 2 2 C4 AN[18] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 1 1 D5 AN[21] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 144 173 B4 AN[22] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 132 161 B8 AN[23] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 131 160 C9 AN[24] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 130 159 D8 AN[25] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 129 158 B9 AN[27] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 128 157 A10 AN[28] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 127 156 B10 AN[30] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 126 155 D9 AN[31] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 125 154 D10 AN[32] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 124 153 C10 AN[33] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 123 152 C11 AN[34] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 122 151 C5 AN[35] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - 121 150 D11 7 F48 E38 AN[36] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - -- 174 AN[37] Single Ended Analog Input -- -- I VDDA I/- AN[x] / - -- 1757 Pinout and signal description 41 Table 2. MPC563xM signal properties (continued) Freescale Semiconductor Table 2. MPC563xM signal properties (continued) Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 AN[38]-AN[8]ANW Single Ended Analog Input Multiplexed Analog Input -- -- I VDDA I/- AN[38] / - 9 9 B3 AN[39]-AN[10]ANY Single Ended Analog Input Multiplexed Analog Input -- -- I VDDA I/- AN[39] / - 8 8 D2 VRH Voltage Reference High -- -- I VDDA -/- VRH 134 163 A8 VRL Voltage Reference Low -- -- I VSSA0 -/- VRL 133 162 A9 REFBYPC Bypass Capacitor Input -- -- I VRL -/- REFBYPC 135 164 B7 eTPU2 eTPU_A Ch. eTPU_A Ch. eTPU_A Ch. GPIO PCR[114] 011 010 100 000 I/O O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 52 61 L4, N3 eTPU_A[1] eTPU_A[13] GPIO[115] eTPU_A Ch. eTPU_A Ch. GPIO PCR[115] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 51 60 M3 eTPU_A[2] eTPU_A[14] GPIO[116] eTPU_A Ch. eTPU_A Ch. GPIO PCR[116] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 50 59 P2 eTPU_A[3] eTPU_A[15] GPIO[117] eTPU_A Ch. eTPU_A Ch. GPIO PCR[117] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 49 58 P1 eTPU_A[4] eTPU_A[16] GPIO[118] eTPU_A Ch. eTPU_A Ch. GPIO PCR[118] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 47 56 N2 eTPU_A[5] eTPU_A[17] DSPI_B_SCK_LVDSGPIO[119] eTPU_A Ch. eTPU_A Ch. DSPI_B CLOCK LVDSGPIO PCR[119] 001 010 100 000 I/O O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 45 54 M4 eTPU_A[6] eTPU_A[18] DSPI_B_SCK_LVDS+ GPIO[120] eTPU_A Ch. eTPU_A Ch. DSPI_B Clock LVDS+ GPIO PCR[120] 001 010 100 000 I/O O O I/O VDDEH1b Medium - / WKPCFG - / WKPCFG 44 53 L3 42 Pinout and signal description eTPU_A[0] eTPU_A[12] eTPU_A[19] GPIO[114] Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor eTPU_A[7] eTPU_A[19] DSPI_B_SOUT_LVDSeTPU_A[6] GPIO[121] eTPU_A Ch. eTPU_A Ch. DSPI_B Data Output LVDSeTPU_A Ch. GPIO PCR[121] 0001 0010 0100 1000 0000 I/O O O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 43 52 K3 eTPU_A[8] eTPU_A[20] DSPI_B_SOUT_LVDS+ GPIO[122] eTPU_A Ch. eTPU_A Ch. DSPI_B Data Output LVDS+ GPIO PCR[122] 001 010 100 000 I/O O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 42 51 N1 eTPU_A[9] eTPU_A[21] GPIO[123] eTPU_A Ch. eTPU_A Ch. GPIO PCR[123] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 41 50 M2 eTPU_A[10] eTPU_A[22] GPIO[124] eTPU_A Ch. eTPU_A Ch. GPIO PCR[124] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 40 49 M1 eTPU_A[11] eTPU_A[23] GPIO[125] eTPU_A Ch. eTPU_A Ch. GPIO PCR[125] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 39 48 L2 eTPU_A[12] DSPI_B_PCS[1] GPIO[126] eTPU_A Ch. DSPI_B Periph Chip Select GPIO PCR[126] 01 10 00 I/O O I/O VDDEH1b Medium - / WKPCFG - / WKPCFG 38 47 L1 eTPU_A[13] DSPI_B_PCS[3] GPIO[127] eTPU_A Ch. DSPI_B Periph Chip Select GPIO PCR[127] 01 10 00 I/O O I/O VDDEH1b Medium - / WKPCFG - / WKPCFG 37 46 J4 eTPU_A[14] DSPI_B_PCS[4] eTPU_A[9] GPIO[128] eTPU_A Ch. DSPI_B Periph Chip Select eTPU_A Ch. GPIO PCR[128] 001 010 100 000 I/O O O I/O VDDEH1b Medium - / WKPCFG - / WKPCFG 35 42 J3 eTPU_A[15] DSPI_B_PCS[5] GPIO[129] eTPU_A Ch. DSPI_B Periph Chip Select GPIO PCR[129] 01 10 00 I/O O I/O VDDEH1b Medium - / WKPCFG - / WKPCFG 33 40 K2 eTPU_A[16] GPIO[130] eTPU_A Ch. GPIO PCR[130] 01 00 I/O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 32 39 K1 eTPU_A[17] GPIO[131] eTPU_A Ch. GPIO PCR[131] 01 00 I/O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 31 38 H3 Pinout and signal description 43 Table 2. MPC563xM signal properties (continued) Freescale Semiconductor Table 2. MPC563xM signal properties (continued) Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 eTPU_A Ch. GPIO PCR[132] 01 00 I/O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 30 37 H4 eTPU_A[19] GPIO[133] eTPU_A Ch. GPIO PCR[133] 01 00 I/O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 29 36 J2 eTPU_A[20] IRQ[8] GPIO[134] eTPU_A Ch. External Interrupt Request GPIO PCR[134] 01 10 00 I/O I I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 28 35 J1 eTPU_A[21] IRQ[9] GPIO[135] eTPU_A Ch. External Interrupt Request GPIO PCR[135] 01 10 00 I/O I I/O VDDEH1a Slow - / WKPCFG - / WKPCFG 27 34 G4 eTPU_A[22] IRQ[10] eTPU_A[17] GPIO[136] eTPU_A Ch. External Interrupt Request eTPU_A Ch. External GPIO PCR[136] 001 010 100 000 I/O I O I/O VDDEH1a Slow - / WKPCFG - / WKPCFG 25 32 H2 eTPU_A[23] IRQ[11] eTPU_A[21] GPIO[137] eTPU_A Ch. External Interrupt Request eTPU_A Ch. External GPIO PCR[137] 001 010 100 000 I/O I O I/O VDDEH1a Slow - / WKPCFG - / WKPCFG 23 30 H1 eTPU_A[24]28 IRQ[12] DSPI_C_SCK_LVDSGPIO[138] eTPU_A Ch. External Interrupt Request DSPI_C Clock LVDSGPIO PCR[138] 001 010 100 000 I/O I O I/O VDDEH1a Slow - / WKPCFG - / WKPCFG 21 28 G1 eTPU_A[25]28 IRQ[13] DSPI_C_SCK_LVDS+ GPIO[139] eTPU_A Ch. External Interrupt Request DSPI _C Clock LVDS+ GPIO PCR[139] 001 010 100 000 I/O I O I/O VDDEH1a Medium - / WKPCFG - / WKPCFG 20 27 G3 eTPU_A[26]28 IRQ[14] DSPI_C_SOUT_LVDSGPIO[140] eTPU_A Ch. External Interrupt Request DSPI_C Data Output LVDSGPIO PCR[140] 001 010 100 000 I/O I O I/O VDDEH1a Slow - / WKPCFG - / WKPCFG 19 26 F3 eTPU_A[27]28 IRQ[15] DSPI_C_SOUT_LVDS+ DSPI_B_SOUT GPIO[141] PCR[141] eTPU_A Ch. External Interrupt Request DSPI_C Data Output LVDS+ DSPI_B Data Output GPIO 0001 0010 0100 1000 0000 I/O I O O I/O VDDEH1a Slow - / WKPCFG - / WKPCFG 18 25 G2 44 Pinout and signal description eTPU_A[18] GPIO[132] Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 eTPU_A[28]28 DSPI_C_PCS[1] GPIO[142] eTPU_A Ch. (Input and Output) DSPI_C Periph Chip Select GPIO PCR[142] 10 01 00 I/O O I/O VDDEH1a Medium - / WKPCFG - / WKPCFG 17 24 F1 eTPU_A[29]28 DSPI_C_PCS[2] GPIO[143] eTPU_A Ch. (Input and Output) DSPI_C Periph Chip Select GPIO PCR[143] 10 01 00 I/O O I/O VDDEH1a Medium - / WKPCFG - / WKPCFG 16 23 F2 eTPU_A[30] DSPI_C_PCS[3] eTPU_A[11] GPIO[144] eTPU_A Ch. DSPI_C Periph Chip Select eTPU_A Ch. GPIO PCR[144] 011 010 001 000 I/O O O I/O VDDEH1a Medium - / WKPCFG - / WKPCFG 15 22 E1 eTPU_A[31] DSPI_C_PCS[4] eTPU_A[13] GPIO[145] eTPU_A Ch. DSPI_C Periph Chip Select eTPU_A Ch. GPIO PCR[145] 011 010 001 000 I/O O O I/O VDDEH1a Medium - / WKPCFG - / WKPCFG 14 21 E2 eMIOS Freescale Semiconductor eMIOS[0] eTPU_A[0] eTPU_A[25]29 GPIO[179] eMIOS Ch. eTPU_A Ch. eTPU_A Ch. GPIO PCR[179] 001 010 100 000 I/O O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 54 63 T4 eMIOS[1] eTPU_A[1] GPIO[180] eMIOS Ch. eTPU_A Ch. GPIO PCR[180] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG -- 647 T58 eMIOS[2] eTPU_A[2] GPIO[181] eMIOS Ch. eTPU_A Ch. GPIO PCR[181] 01 10 00 I/O O I/O VDDEH1b Slow - / WKPCFG - / WKPCFG 55 65 N7 eMIOS[4] eTPU_A[4] GPIO[183] eMIOS Ch. eTPU_A Ch. GPIO PCR[183] 01 10 00 I/O O I/O VDDEH6a Slow - / WKPCFG - / WKPCFG 56 67 R5 eMIOS[8] eTPU_A[8]30 SCI_B_TX GPIO[187] eMIOS Ch. eTPU_A Ch. eSCI_B Transmit GPIO PCR[187] 001 010 100 000 I/O O O I/O VDDEH6a Slow - / WKPCFG - / WKPCFG 57 70 P8 Pinout and signal description 45 Table 2. MPC563xM signal properties (continued) Freescale Semiconductor Table 2. MPC563xM signal properties (continued) Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 eMIOS[9] eTPU_A[9]30 SCI_B_RX GPIO[188] eMIOS Ch. eTPU_A Ch. eSCI_B Receive GPIO PCR[188] 001 010 100 000 I/O O I I/O VDDEH6a Slow - / WKPCFG - / WKPCFG 58 71 R7 eMIOS[10] GPIO[189] eMIOS Ch. GPIO PCR[189] 01 00 I/O I/O VDDEH6a Slow - / WKPCFG - / WKPCFG 60 73 N8 eMIOS[11] GPIO[190] eMIOS Ch. GPIO PCR[190] 01 00 I/O I/O VDDEH6a Slow - / WKPCFG - / WKPCFG 62 75 R8 eMIOS[12] DSPI_C_SOUT eTPU_A[27] GPIO[191] eMIOS Ch. DSPI C Data Output eTPU_A Ch. GPIO PCR[191] 001 010 100 000 I/O O O I/O VDDEH6a Medium - / WKPCFG - / WKPCFG 63 76 N10 eMIOS[13] GPIO[192] eMIOS Ch. GPIO PCR[192] 01 00 I/O I/O VDDEH6a - / WKPCFG - / WKPCFG -- 777 T88 eMIOS[14] IRQ[0] eTPU_A[29] GPIO[193] eMIOS Ch. External Interrupt Request eTPU_A Ch. GPIO PCR[193] 001 010 100 000 O I O I/O VDDEH6a Slow - / WKPCFG - / WKPCFG 64 78 R9 eMIOS[15] IRQ[1] GPIO[194] eMIOS Ch. External Interrupt Request GPIO PCR[194] 01 10 00 O I I/O VDDEH6a Slow - / WKPCFG - / WKPCFG -- 797 T98 eMIOS[23] GPIO[202] eMIOS Ch. GPIO PCR[202] 01 00 I/O I/O VDDEH6a Slow - / WKPCFG - / WKPCFG 65 80 R11 Clock Synthesizer Crystal Oscillator Output -- -- O VDDEH6a O/- XTAL31 / - 76 93 P16 EXTAL EXTCLK Crystal Oscillator Input External Clock Input -- -- I VDDEH6a I/- EXTAL32/ - 75 92 N16 CLKOUT System Clock Output -- O VDDE5 Fast CLKOUT / Enabled CLKOUT / Enabled -- -- T14 PCR[229] Power / Ground VDDPLL PLL Supply Voltage -- -- I VDDPLL (1.2V) I/- -- 74 91 R16 VSSPLL33 PLL Ground -- -- I VSSPLL I/- -- 77 94 M16 46 Pinout and signal description XTAL Name 1 Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 VSTBY Power Supply for Standby RAM -- -- I VSTBY I/- -- 12 12 C1 VRC33 3.3V Voltage Regulator Bypass Capacitor -- -- O VRC33 O/- -- 13 13 A15, D1, N6, N12 VRCCTL Voltage Regulator Control Output -- -- O NA O/- -- 11 11 N14 VDDA34 Analog Power Input for eQADC -- -- I VDDA (5.0 V) I/- -- 6 6 -- VDDA0 Analog Power Input for eQADC -- -- I VDDA I/- -- -- -- B11 VSSA0 Analog Ground Input for eQADC -- -- I VSSA I/- -- -- -- A11 VDDA1 Analog Power Input for eQADC -- -- I VDDA I/- -- -- -- A4 VSSA1 Analog Ground Input for eQADC -- -- I VSSA I/- -- -- -- A5 VSSA35 Analog Ground Input for eQADC -- -- I VSSA I/- -- 7 7 -- VDDREG Voltage Regulator Supply -- -- I VDDREG (5.0 V) I/- -- 10 10 K16 VDD Internal Logic Supply Input -- -- I VDD (1.2 V) I/- -- 26, 53, 33, 62, B1, B16, C2, 86, 120 103, D3, E4, N5, 149 P4, P13, R3, R14, T2, T15 Pinout and signal description 47 Table 2. MPC563xM signal properties (continued) Freescale Semiconductor Freescale Semiconductor Table 2. MPC563xM signal properties (continued) 1 Name Function Pad Config. Register (PCR)2 PCR PA Field3 I/O Type Voltage4 / Pad Type Pin No. Reset State5 Function / State After Reset6 144 LQFP 176 LQFP 208 MAPB GA MPC5634M Microcontroller Data Sheet, Rev. 9 VSS Ground -- -- - VSS0 I/- -- 22, 36, 15, 29, A1, A16, B2, B15, C3, 48, 59, 43, 57, C14, D4, 73, 79, 72, 90, 96, D13, G7, 91, 108, G8, G9, 104, 1157, G10, H7, 115 H8, H9, 127, 133, H10, J7, J8, 140 J9, J10, K7, K8, K9, K10, N4, N13, P3, P14, R2, R15, T1, T16 VDDEH1A36 VDDEH1B36 I/O Supply Input -- -- I VDDEH137 (3.3V - 5.0V) I/- -- 24, 34, 31, 41 46 55 VDDE5 I/O Supply Input -- -- I VDDE5 I/- -- VDDEH6a38, 39 I/O Supply Input -- -- I VDDEH6 (3.3V - 5.0V) I/- -- VDDEH6 I/O Supply Input -- -- I VDDEH6 I/- -- -- -- F13 VDDEH7 I/O Supply Input -- -- I VDDEH740 (3.3V - 5.0V) I/- -- 102, 113 125, 138 D12 VDDE741 I/O Supply Input -- -- I VDDE7 (3.3V) I/- -- -- 16, 1197 E13, P6 VDDEH6b39 1 3 4 5 6 7 8 -- 78, 93, 95, 61 110, 74 T13 -- 48 For each pin in the table, each line in the Function column is a separate function of the pin. For all I/O pins the selection of primary pin function or secondary function or GPIO is done in the SIU except where explicitly noted. Values in this column refer to registers in the System Integration Unit (SIU). The actual register name is "SIU_PCR" suffixed by the PCR number. For example, PCR[190] refers to the SIU register named SIU_PCR190. The Pad Configuration Register (PCR) PA field is used by software to select pin function. The VDDE and VDDEH supply inputs are broken into segments. Each segment of slow I/O pins (VDDEH) may have a separate supply in the 3.3 V to 5.0 V range (-10%/+5%). Each segment of fast I/O (VDDE) may have a separate supply in the 1.8 V to 3.3 V range (+/- 10%). Terminology is O -- output, I -- input, Up -- weak pull up enabled, Down -- weak pull down enabled, Low -- output driven low, High -- output driven high. A dash for the function in this column denotes that both the input and output buffer are turned off. Function after reset of GPI is general purpose input. A dash for the function in this column denotes that both the input and output buffer are turned off. Not available on 1 MB version of 176-pin package. Not available on 1 MB version of 208-pin package. Pinout and signal description 2 -- K4 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor The GPIO functions on GPIO[206] and GPIO[207] can be selected as trigger functions in the SIU for the ADC by making the proper selections in the SIU_ETISR and SIU_ISEL3 registers in the SIU. 10 Some signals in this section are available only on calibration package. 11 These pins are only available in the 496 CSP/MAPBGA calibration/development package. 12 On the calibration package, the Nexus function on this pin is enabled when the NEXUSCFG pin is high and Nexus is configured to full port mode. On the 176-pin and 208-pin packages, the Nexus function on this pin is enabled permanently. Do not connect the Nexus MDO or MSEO pins directly to a power supply or ground. 13 In the calibration package, the I/O segment containing this pin is called VDDE12. 14 208-ball BGA package only 15 When configured as Nexus (208-pin package or calibration package with NEXUSCFG=1), and JCOMP is asserted during reset, MDO[0] is driven high until the crystal oscillator becomes stable, at which time it is then negated. 16 The function of this pin is Nexus when NEXUSCFG is high. 17 High when the pin is configured to Nexus, low otherwise. 18 O/Low for the calibration with NEXUSCFG=0; I/Up otherwise. 19 ALT_ADDR/Low for the calibration package with NEXUSCFG=0; EVTI/Up otherwise. 20 In 176-pin and 208-pin packages, the Nexus function is disabled and the pin/ball has the secondary function 21 This signal is not available in the 176-pin and 208-pin packages. 22 The primary function is not selected via the PA field when the pin is a Nexus signal. Instead, it is activated by the Nexus controller. 23 TDI and TDO are required for JTAG operation. 24 The primary function is not selected via the PA field when the pin is a JTAG signal. Instead, it is activated by the JTAG controller. 25 The function and state of the CAN_A and eSCI_A pins after execution of the BAM program is determined by the BOOTCFG1 pin. 26 Connect an external 10K pull-up resistor to the SCI_A_RX pin to ensure that the pin is driven high during CAN serial boot. 27 For pins AN[0:7], during and just after POR negates, internal pull resistors can be enabled, resulting in as much as 4 mA of current draw. The pull resistors are disabled when the system clock propagates through the device. 28 ETPUA[24:29] are input and output. The input muxing is controlled by SIU_ISEL8 register. 29 eTPU_A[25] is an output only function. 30 Only the output channels of eTPU[8:9] are connected to pins. 31 The function after reset of the XTAL pin is determined by the value of the signal on the PLLCFG[1] pin. When bypass mode is chosen XTAL has no function and should be grounded. 32 The function after reset of the EXTAL_EXTCLK pin is determined by the value of the signal on the PLLCFG[1] pin. If the EXTCLK function is chosen, the valid operating voltage for the pin is 1.62 V to 3.6 V. If the EXTAL function is chosen, the valid operating voltage is 3.3 V. 33 VSSPLL and VSSREG are connected to the same pin. 34 This pin is shared by two pads: VDDA_AN, using pad_vdde_hv, and VDDA_DIG, using pad_vdde_int_hv. 35 This pin is shared by two pads: VSSA_AN, using pad_vsse_hv, and VSSA_DIG, using pad_vsse_int_hv. 36 VDDEH1A, VDDEH1B, and VDDEH1AB are shorted together in all production packages. The separation of the signal names is present to support legacy naming, however they should be considered as the same signal in this document. 37 LVDS pins will not work at 3.3 V. 38 The VDDEH6 segment may be powered from 3.0 V to 5.0 V for mux address or SSI functions, but must meet the VDDA specifications of 4.5 V to 5.25 V for analog input function. Pinout and signal description 49 9 50 together in all production packages. The separation of the signal names is present to support legacy naming, however they should be considered as the same signal in this document. 40 If using JTAG or Nexus, the I/O segment that contains the JTAG and Nexus pins must be powered by a 5 V supply. The 3.3 V Nexus/JTAG signals are derived from the 5 volt power supply. 41 In the calibration package this signal is named VDDE12. Table 3. Pad types MPC5634M Microcontroller Data Sheet, Rev. 9 Pad Type Name Supply Voltage Slow pad_ssr_hv 3.0 V - 5.25 V Medium pad_msr_hv 3.0 V - 5.25 V Fast pad_fc 3.0 V - 3.6 V MultiV pad_multv_hv 3.0 V - 5.25 V (high swing mode) 4.5 V - 5.25 V (low swing mode) Analog pad_ae_hv 0.0 - 5.25 V LVDS pad_lo_lv -- Pinout and signal description 39 VDDEH6A and VDDEH6B are shorted Freescale Semiconductor Pinout and signal description 3.7 Signal details Table 4 contains details on the multiplexed signals that appear in Table 2, "MPC563xM signal properties". Table 4. Signal details Signal Module or Function Description CLKOUT Clock Generation MPC5634M clock output for the external/calibration bus interface EXTAL Clock Generation Input pin for an external crystal oscillator or an external clock source based on the value driven on the PLLREF pin at reset. EXTCLK Clock Generation External clock input PLLREF Clock Generation PLLREF is used to select whether the oscillator operates in xtal mode or external reference mode from reset. PLLREF=0 selects external reference mode. XTAL Clock Generation Crystal oscillator input SCK_B_LVDS- SCK_B_LVDS+ DSPI LVDS pair used for DSPI_B TSB mode transmission SOUT_B_LVDS- SOUT_B_LVDS+ DSPI LVDS pair used for DSPI_B TSB mode transmission SCK_C_LVDS- SCK_C_LVDS+ DSPI LVDS pair used for DSPI_C TSB mode transmission SOUT_C_LVDS- SOUT_C_LVDS+ DSPI LVDS pair used for DSPI_C TSB mode transmission PCS_B[0] PCS_C[0] DSPI_B - DSPI_C Peripheral chip select when device is in master mode--slave select when used in slave mode PCS_B[1:5] PCS_C[1:5] DSPI_B - DSPI_C Peripheral chip select when device is in master mode--not used in slave mode SCK_B SCK_C DSPI_B - DSPI_C DSPI clock--output when device is in master mode; input when in slave mode SIN_B SIN_C DSPI_B - DSPI_C DSPI data in SOUT_B SOUT_C DSPI_B - DSPI_C DSPI data out CAL_ADDR[12:30] Calibration Bus The CAL_ADDR[12:30] signals specify the physical address of the bus transaction. CAL_CS[0:3] Calibration Bus CSx is asserted by the master to indicate that this transaction is targeted for a particular memory bank on the Primary external bus. CAL_DATA[0:15] Calibration Bus The CAL_DATA[0:15] signals contain the data to be transferred for the current transaction. CAL_OE Calibration Bus OE is used to indicate when an external memory is permitted to drive back read data. External memories must have their data output buffers off when OE is negated. OE is only asserted for chip-select accesses. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 51 Pinout and signal description Table 4. Signal details (continued) Signal Module or Function Description CAL_RD_WR Calibration Bus RD_WR indicates whether the current transaction is a read access or a write access. CAL_TS_ALE Calibration Bus The Transfer Start signal (TS) is asserted by the MPC5634M to indicate the start of a transfer. The Address Latch Enable (ALE) signal is used to demultiplex the address from the data bus. CAL_EVTO Calibration Bus Nexus Event Out CAL_MCKO Calibration Bus Nexus Message Clock Out NEXUSCFG Nexus/Calibration Bus Nexus/Calibration Bus selector eMIOS[0:23] eMIOS eMIOS I/O channels AN[0:39] eQADC Single-ended analog inputs for analog-to-digital converter FCK eQADC eQADC free running clock for eQADC SSI. MA[0:2] eQADC These three control bits are output to enable the selection for an external Analog Mux for expansion channels. REFBYPC eQADC Bypass capacitor input SDI eQADC Serial data in SDO eQADC Serial data out SDS eQADC Serial data select VRH eQADC Voltage reference high input VRL eQADC Voltage reference low input SCI_A_RX SCI_B_RX eSCI_A - eSCI_B eSCI receive SCI_A_TX SCI_B_TX eSCI_A - eSCI_B eSCI transmit ETPU_A[0:31] eTPU eTPU I/O channel CAN_A_TX CAN_C_TX FlexCan_A - FlexCAN_C FlexCAN transmit CAN_A_RX CAN_C_RX FlexCAN_A - FlexCAN_C FlexCAN receive JCOMP JTAG Enables the JTAG TAP controller. TCK JTAG Clock input for the on-chip test and debug logic. TDI JTAG Serial test instruction and data input for the on-chip test and debug logic. TDO JTAG Serial test data output for the on-chip test logic. TMS JTAG Controls test mode operations for the on-chip test and debug logic. MPC5634M Microcontroller Data Sheet, Rev. 9 52 Freescale Semiconductor Pinout and signal description Table 4. Signal details (continued) Signal Module or Function Description EVTI Nexus EVTI is an input that is read on the negation of RESET to enable or disable the Nexus Debug port. After reset, the EVTI pin is used to initiate program synchronization messages or generate a breakpoint. EVTO Nexus Output that provides timing to a development tool for a single watchpoint or breakpoint occurrence. MCKO Nexus MCKO is a free running clock output to the development tools which is used for timing of the MDO and MSEO signals. MDO[3:0] Nexus Trace message output to development tools. This pin also indicates the status of the crystal oscillator clock following a power-on reset, when MDO[0] is driven high until the crystal oscillator clock achieves stability and is then negated. MSEO[1:0] Nexus Output pin--Indicates the start or end of the variable length message on the MDO pins BOOTCFG[1] SIU - Configuration The BOOTCFG1 pin is sampled during the assertion of the RSTOUT signal, and the value is used to update the RSR and the BAM boot mode The following values are for BOOTCFG[0:1}: 0 Boot from internal flash memory 1 FlexCAN/eSCI boot WKPCFG SIU - Configuration The WKPCFG pin is applied at the assertion of the internal reset signal (assertion of RSTOUT), and is sampled 4 clock cycles before the negation of the RSTOUT pin. The value is used to configure whether the eTPU and eMIOS pins are connected to internal weak pull up or weak pull down devices after reset. The value latched on the WKPCFG pin at reset is stored in the Reset Status Register (RSR), and is updated for all reset sources except the Debug Port Reset and Software External Reset. 0: Weak pulldown applied to eTPU and eMIOS pins at reset 1: Weak pullup applied to eTPU and eMIOS pins at reset. ETRIG[2:3] SIU - eQADC Triggers External signal eTRIGx triggers eQADC CFIFOx IRQ[0:15] SIU - External Interrupts The IRQ[0:15] pins connect to the SIU IRQ inputs. IMUX Select Register 1 is used to select the IRQ[0:15] pins as inputs to the IRQs. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 53 Pinout and signal description Table 4. Signal details (continued) Signal Module or Function Description NMI SIU - External Interrupts Non-Maskable Interrupt GPIO[n] SIU - GPIO Configurable general purpose I/O pins. Each GPIO input and output is separately controlled by an 8-bit input (GPDI) or output (GPDO) register. Additionally, each GPIO pins is configured using a dedicated SIU_PCR register. The GPIO pins are generally multiplexed with other I/O pin functions. SIU - Reset RESET The RESET pin is an active low input. The RESET pin is asserted by an external device during a power-on or external reset. The internal reset signal asserts only if the RESET pin asserts for 10 clock cycles. Assertion of the RESET pin while the device is in reset causes the reset cycle to start over. The RESET pin has a glitch detector which detects spikes greater than two clock cycles in duration that fall below the switch point of the input buffer logic of the VDDEH input pins. The switch point lies between the maximum VIL and minimum VIH specifications for the VDDEH input pins. RSTOUT SIU - Reset The RSTOUT pin is an active low output that uses a push/pull configuration. The RSTOUT pin is driven to the low state by the MCU for all internal and external reset sources. There is a delay between initiation of the reset and the assertion of the RSTOUT pin. Table 5 gives the power/ground segmentation of the MPC563x MCU. Each segment provides the power and ground for the given set of I/O pins, and can be powered by any of the allowed voltages regardless of the power on the other segments. . Table 5. MPC563x Power/Ground Segmentation Power Segment 144-LQFP Pin Number 176-LQFP Pin Number 208-BGA Pin Number Voltage Range1 I/O Pins Powered by Segment VDDA0 6 6 B11 5.0 V AN[0:7], AN[9], AN[11], AN[16:18], AN[21:25], AN[27:28], AN[30:37], AN38, AN39, VRL, REFBYPC, VRH VDDE5 -- -- T13 1.8 V - 3.3 V CLKOUT VDDEH1 (a,b) 24, 34 31, 41 K4 3.3 V - 5.0 V PCKCFG[2], eTPU_A[0:31], eMIOS[0:2] MPC5634M Microcontroller Data Sheet, Rev. 9 54 Freescale Semiconductor Pinout and signal description Table 5. MPC563x Power/Ground Segmentation (continued) 144-LQFP Pin Number 176-LQFP Pin Number 208-BGA Pin Number VDDEH6 (a,b) 78, 93 95, 110 VDDEH72 102, 113 VDDE123 VDDE7 -- Power Segment Voltage Range1 I/O Pins Powered by Segment F13 3.3 V - 5.0 V RESET, RSTOUT, WKPCFG, BOOTCFG1, PLLREF, SCK_B, PCKCFG[0], CAN_A_TX, CAN_A_RX, CAN_C_TX, CAN_C_RX, SCI_A_TX, SCI_A_RX, SCI_B_TX, SCI_B_RX, SCK_B, SIN_B, SOUT_B, DSPI_B_PCS_B[0:5], eMIOS[4], eMIOS[8:15], eMIOS[23], XTAL, EXTAL 125, 138 D12 3.3 V - 5.0 V PCKCFG[1], MDO[0:3], EVTI, EVTO, MCKO, MSEO[0:1], TDO, TDI, TMS, TCK, JCOMP, AN[12:15] (GPIO[98:99], GPIO[206:207]) 16, 119 E13, P6 1.8 V - 3.3 V CAL_ADDR[12:30], CAL_DATA[0:15], CAL_CS[0], CAL_CS[2:3], CAL_RD_WR, CAL_WE[0:1], CAL_OE, CAL_TS, ALT_MCKO, ALT_EVTO, NEXUSCFG 1 These are nominal voltages. All VDDE and VDDEH voltages are -5%, +10% (VDDE 1.62 V to 3.6 V, VDDEH 3.0 V to 5.5 V). VDDA is +5%, -10%. 2 The VDDEH7 segment may be powered from 3.0 V to 5.0 V for mux address or SSI functions, but must meet the VDDA specifications of 4.5 V to 5.25 V for analog input function. 3 In the calibration package this signal is named VDDE12; it is named VDDE7 in all other packages. , MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 55 Electrical characteristics 4 Electrical characteristics This section contains detailed information on power considerations, DC/AC electrical characteristics, and AC timing specifications for the MPC5634M series of MCUs. The electrical specifications are preliminary and are from previous designs, design simulations, or initial evaluation. These specifications may not be fully tested or guaranteed at this early stage of the product life cycle, however for production silicon these specifications will be met. Finalized specifications will be published after complete characterization and device qualifications have been completed. In the tables where the device logic provides signals with their respective timing characteristics, the symbol "CC" for Controller Characteristics is included in the Symbol column. In the tables where the external system must provide signals with their respective timing characteristics to the device, the symbol "SR" for System Requirement is included in the Symbol column. 4.1 Parameter classification The electrical parameters shown in this document are guaranteed by various methods. To provide a better understanding, the classifications listed in Table 6 are used and the parameters are tagged accordingly in the tables. Note that only controller characteristics ("CC") are classified. System requirements ("SR") are operating conditions that must be provided to ensure normal device operation. Table 6. Parameter classifications Classification tag Tag description P Those parameters are guaranteed during production testing on each individual device. C Those parameters are achieved by the design characterization by measuring a statistically relevant sample size across process variations. T Those parameters are achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted. All values shown in the typical column are within this category. D Those parameters are derived mainly from simulations. NOTE The classification is shown in the column labeled "C" in the parameter tables where appropriate. 4.2 Maximum ratings Table 7. Absolute maximum ratings1 Value Symbol VDD VFLASH Parameter SR SR Conditions 1.2 V core supply voltage2 Flash core voltage3 4 Unit min max - 0.3 1.32 V - 0.3 5.5 V VSTBY SR SRAM standby voltage - 0.3 5.5 V VDDPLL SR Clock synthesizer voltage - 0.3 1.32 V VRC335 SR Voltage regulator control input voltage - 0.3 3.6 V MPC5634M Microcontroller Data Sheet, Rev. 9 56 Freescale Semiconductor Electrical characteristics Table 7. Absolute maximum ratings1 (continued) Value Symbol VDDA 1 2 3 4 5 6 7 Parameter SR Analog supply voltage4 Conditions Reference to VSSA Unit min max - 0.3 5.5 V 6 VDDE SR I/O supply voltage - 0.3 3.6 V VDDEH SR I/O supply voltage4 - 0.3 5.5 V VIN SR DC input voltage7 VDDEH powered I/O pads -1.08 VDDEH + 0.3 V9 V VDDE powered I/O pads -1.010 VDDE + 0.3 V10 VDDA powered I/O pads -1.0 VDDA + 0.3 V - 0.3 5.5 V - 0.3 5.5 V - 0.1 0.1 V - 0.3 5.5 V VDDREG SR Voltage regulator supply voltage6 VRH SR Analog reference high voltage VSS - VSSA SR VSS differential voltage Reference to VRL voltage6 VRH - VRL SR VREF differential VRL - VSSA SR VRL to VSSA differential voltage - 0.3 0.3 V VSSPLL - VSS SR VSSPLL to VSS differential voltage - 0.1 0.1 V IMAXD SR Maximum DC digital input current11 Per pin, applies to all digital pins -3 3 mA IMAXA SR Maximum DC analog input current12 Per pin, applies to all analog pins -- 5 mA TJ SR Maximum operating temperature range13 - die junction temperature - 40.0 150.0 oC TSTG SR Storage temperature range - 55.0 150.0 oC TSDR SR Maximum solder temperature14 -- 260.0 oC MSL SR Moisture sensitivity level15 -- 3 -- Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the listed maxima may affect device reliability or cause permanent damage to the device. Allowed 2 V for 10 hours cumulative time, remaining time at 1.2 V +10%. The VFLASH supply is connected to VDDEH1. Allowed 6.8 V for 10 hours cumulative time, remaining time at 5 V +10%. The pin named as VRC33 is internally connected to the pads VFLASH and VRC33 in the 144 LQFP package. These limits apply when the internal regulator is disabled and VRC33 power is supplied externally. All functional non-supply I/O pins are clamped to VSS and VDDE, or VDDEH. AC signal overshoot and undershoot of up to 2.0 V of the input voltages is permitted for an accumulative duration of 60 hours over the complete lifetime of the device (injection current not limited for this duration). MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 57 Electrical characteristics 8 Internal structures hold the voltage greater than -1.0 V if the injection current limit of 2 mA is met. Internal structures hold the input voltage less than the maximum voltage on all pads powered by VDDEH supplies, if the maximum injection current specification is met (2 mA for all pins) and VDDEH is within the operating voltage specifications. 10 Internal structures hold the input voltage less than the maximum voltage on all pads powered by VDDE supplies, if the maximum injection current specification is met (2 mA for all pins) and VDDE is within the operating voltage specifications. 11 Total injection current for all pins (including both digital and analog) must not exceed 25 mA. 12 Total injection current for all analog input pins must not exceed 15 mA. 13 Lifetime operation at these specification limits is not guaranteed. 14 Solder profile per CDF-AEC-Q100. 15 Moisture sensitivity per JEDEC test method A112. 9 4.3 Thermal characteristics Table 8. Thermal characteristics for 144-pin LQFP Symbol C Parameter Conditions Value Unit Single layer board - 1s 43 C/W Four layer board - 2s2p 35 C/W CC D Junction-to-Ambient, Natural Convection1 RJA CC D Junction-to-Ambient, Natural Convection2 RJMA CC D Junction-to-Ambient (@200 ft/min)2 Single layer board -1s 34 C/W RJMA CC D Junction-to-Ambient (@200 ft/min)2 Four layer board - 2s2p 29 C/W 22 C/W 8 C/W 2 C/W RJA RJB CC D Junction-to-Board2 (Top)3 RJCtop CC D Junction-to-Case JT CC D Junction-to-Package Top, Natural Convection4 1 Junction-to-Ambient Thermal Resistance determined per JEDEC JESD51-3 and JESD51-6. Thermal test board meets JEDEC specification for this package. 2 Junction-to-Board thermal resistance determined per JEDEC JESD51-8. Thermal test board meets JEDEC specification for the specified package. 3 Junction-to-Case at the top of the package determined using MIL-STD 883 Method 1012.1. The cold plate temperature is used for the case temperature. Reported value includes the thermal resistance of the interface layer. 4 Thermal characterization parameter indicating the temperature difference between the package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. MPC5634M Microcontroller Data Sheet, Rev. 9 58 Freescale Semiconductor Electrical characteristics Table 9. Thermal characteristics for 176-pin LQFP1 Symbol C Parameter Conditions 2 RJA CC D Junction-to-Ambient, Natural Convection RJA CC D Junction-to-Ambient, Natural Convection2 2 RJMA CC D Junction-to-Moving-Air, Ambient RJMA CC D Junction-to-Moving-Air, Ambient2 RJB CC D Junction-to-Board3 Value Unit Single layer board - 1s 38 C/W Four layer board - 2s2p 31 C/W @200 ft./min., single layer board - 1s 30 C/W @200 ft./min., four layer board - 2s2p 25 C/W 20 C/W 4 RJCtop CC D Junction-to-Case 5 C/W JT CC D Junction-to-Package Top, Natural Convection5 2 C/W 1 Thermal characteristics are targets based on simulation that are subject to change per device characterization. Junction-to-Ambient Thermal Resistance determined per JEDEC JESD51-3 and JESD51-6. Thermal test board meets JEDEC specification for this package. 3 Junction-to-Board thermal resistance determined per JEDEC JESD51-8. Thermal test board meets JEDEC specification for the specified package. 4 Junction-to-Case at the top of the package determined using MIL-STD 883 Method 1012.1. The cold plate temperature is used for the case temperature. Reported value includes the thermal resistance of the interface layer. 5 Thermal characterization parameter indicating the temperature difference between the package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. 2 Table 10. Thermal characteristics for 208-pin MAPBGA1 Symbol RJA RJMA RJA 3 4 5 6 Conditions Value Unit CC D Junction-to-ambient, natural convection2,3 One layer board - 1s 39 C/W CC D Junction-to-ambient natural convection2,4 Four layer board - 2s2p 24 C/W D Junction-to-ambient (@200 ft/min)2,4 Single layer board 31 C/W ft/min)2,4 Four layer board 2s2p 20 C/W Four layer board - 2s2p 13 C/W 6 C/W 2 C/W CC CC D Junction-to-ambient (@200 RJB CC D Junction-to-board5 JT 2 Parameter RJMA RJC 1 C CC CC D Junction-to-case 6 D Junction-to-package top natural convection7 Thermal characteristics are targets based on simulation that are subject to change per device characterization. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. Per SEMI G38-87 and JEDEC JESD51-2 with the single-layer board horizontal. Per JEDEC JESD51-6 with the board horizontal. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. Indicates the average thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1) with the cold plate temperature used for the case temperature. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 59 Electrical characteristics 7 4.3.1 Thermal characterization parameter indicating the temperature difference between package top and the junction temperature per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT. General notes for specifications at maximum junction temperature An estimation of the chip junction temperature, TJ, can be obtained from the equation: TJ = TA + (RJA * PD) Eqn. 1 where: TA = ambient temperature for the package (oC) RJA = junction-to-ambient thermal resistance (oC/W) PD = power dissipation in the package (W) The thermal resistance values used are based on the JEDEC JESD51 series of standards to provide consistent values for estimations and comparisons. The difference between the values determined for the single-layer (1s) board compared to a four-layer board that has two signal layers, a power and a ground plane (2s2p), demonstrate that the effective thermal resistance is not a constant. The thermal resistance depends on the: * * * * Construction of the application board (number of planes) Effective size of the board which cools the component Quality of the thermal and electrical connections to the planes Power dissipated by adjacent components Connect all the ground and power balls to the respective planes with one via per ball. Using fewer vias to connect the package to the planes reduces the thermal performance. Thinner planes also reduce the thermal performance. When the clearance between the vias leave the planes virtually disconnected, the thermal performance is also greatly reduced. As a general rule, the value obtained on a single-layer board is within the normal range for the tightly packed printed circuit board. The value obtained on a board with the internal planes is usually within the normal range if the application board has: * * * One oz. (35 micron nominal thickness) internal planes Components are well separated Overall power dissipation on the board is less than 0.02 W/cm2 The thermal performance of any component depends on the power dissipation of the surrounding components. In addition, the ambient temperature varies widely within the application. For many natural convection and especially closed box applications, the board temperature at the perimeter (edge) of the package is approximately the same as the local air temperature near the device. Specifying the local ambient conditions explicitly as the board temperature provides a more precise description of the local ambient conditions that determine the temperature of the device. At a known board temperature, the junction temperature is estimated using the following equation: TJ = TB + (RJB * PD) Eqn. 2 where: TB = board temperature for the package perimeter (oC) RJB = junction-to-board thermal resistance (oC/W) per JESD51-8S PD = power dissipation in the package (W) When the heat loss from the package case to the air does not factor into the calculation, an acceptable value for the junction temperature is predictable. Ensure the application board is similar to the thermal test condition, with the component soldered to a board with internal planes. MPC5634M Microcontroller Data Sheet, Rev. 9 60 Freescale Semiconductor Electrical characteristics The thermal resistance is expressed as the sum of a junction-to-case thermal resistance plus a case-to-ambient thermal resistance: RJA = RJC + RCA Eqn. 3 where: RJA = junction-to-ambient thermal resistance (oC/W) RJC = junction-to-case thermal resistance (oC/W) RCA = case to ambient thermal resistance (oC/W) RJC is device related and is not affected by other factors. The thermal environment can be controlled to change the case-to-ambient thermal resistance, RCA. For example, change the air flow around the device, add a heat sink, change the mounting arrangement on the printed circuit board, or change the thermal dissipation on the printed circuit board surrounding the device. This description is most useful for packages with heat sinks where 90% of the heat flow is through the case to heat sink to ambient. For most packages, a better model is required. A more accurate two-resistor thermal model can be constructed from the junction-to-board thermal resistance and the junction-to-case thermal resistance. The junction-to-case thermal resistance describes when using a heat sink or where a substantial amount of heat is dissipated from the top of the package. The junction-to-board thermal resistance describes the thermal performance when most of the heat is conducted to the printed circuit board. This model can be used to generate simple estimations and for computational fluid dynamics (CFD) thermal models. To determine the junction temperature of the device in the application on a prototype board, use the thermal characterization parameter (JT) to determine the junction temperature by measuring the temperature at the top center of the package case using the following equation: TJ = TT + (JT x PD) Eqn. 4 where: TT = thermocouple temperature on top of the package (oC) JT = thermal characterization parameter (oC/W) PD = power dissipation in the package (W) The thermal characterization parameter is measured in compliance with the JESD51-2 specification using a 40-gauge type T thermocouple epoxied to the top center of the package case. Position the thermocouple so that the thermocouple junction rests on the package. Place a small amount of epoxy on the thermocouple junction and approximately 1 mm of wire extending from the junction. Place the thermocouple wire flat against the package case to avoid measurement errors caused by the cooling effects of the thermocouple wire. References: Semiconductor Equipment and Materials International 3081 Zanker Road San Jose, CA 95134 USA (408) 943-6900 MIL-SPEC and EIA/JESD (JEDEC) specifications are available from Global Engineering Documents at 800-854-7179 or 303-397-7956. JEDEC specifications are available on the web at http://www.jedec.org. * * C.E. Triplett and B. Joiner, "An Experimental Characterization of a 272 PBGA Within an Automotive Engine Controller Module," Proceedings of SemiTherm, San Diego, 1998, pp. 47-54. G. Kromann, S. Shidore, and S. Addison, "Thermal Modeling of a PBGA for Air-Cooled Applications", Electronic Packaging and Production, pp. 53-58, March 1998. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 61 Electrical characteristics * B. Joiner and V. Adams, "Measurement and Simulation of Junction to Board Thermal Resistance and Its Application in Thermal Modeling," Proceedings of SemiTherm, San Diego, 1999, pp. 212-220. 4.4 Electromagnetic Interference (EMI) characteristics Table 11. EMI testing specifications1 Symbol Radiated Emissions 1 4.5 Parameter VEME Conditions fOSC/fBUS Frequency Level (Typ) Unit Device Configuration, test conditions and EM testing per standard IEC61967-2; Supply Voltage = 5.0V DC, Ambient Temperature = 25C, Worst-case Orientation Oscillator Frequency = 8 MHz; System Bus Frequency = 80 MHz; No PLL Frequency Modulation 150 kHz - 50 MHz 26 dBV 50-150 MHz 24 150-500 MHz 24 500-1000 MHz 21 IEC Level K -- Oscillator Frequency = 8 MHz; System Bus Frequency = 80 MHz; 1% PLL Frequency Modulation 150 kHz - 50 MHz 20 dBV 50-150 MHz 19 150-500 MHz 14 500-1000 MHz 7 IEC Level L -- IEC Classification Level: L = 24dBuV; K = 30dBuV. Electromagnetic static discharge (ESD) characteristics Table 12. ESD ratings1,2 Symbol Parameter Conditions Value Unit -- SR ESD for Human Body Model (HBM) -- 2000 V R1 SR HBM circuit description -- 1500 C SR -- 100 pF -- SR 500 V ESD for field induced charge Model (FCDM) All pins Corner pins -- -- SR SR Number of pulses per pin Number of pulses 750 Positive pulses (HBM) 1 -- Negative pulses (HBM) 1 -- 1 -- -- 1 All ESD testing is in conformity with CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits. 2 Device failure is defined as: "If after exposure to ESD pulses, the device does not meet the device specification requirements, which includes the complete DC parametric and functional testing at room temperature and hot temperature." MPC5634M Microcontroller Data Sheet, Rev. 9 62 Freescale Semiconductor Electrical characteristics 4.6 Power Management Control (PMC) and Power On Reset (POR) electrical specifications Table 13. PMC Operating conditions and external regulators supply voltage ID 1 Name Jtemp C SR Parameter Min -- Junction temperature Typ Max Unit 27 150 C -40 1 2 Vddreg SR -- PMC 5 V supply voltage VDDREG 4.75 5 5.25 V 3 Vdd SR -- Core supply voltage 1.2 V VDD when external regulator is used without disabling the internal regulator (PMC unit turned on, LVI monitor active)2 1.263 1.3 1.32 V 3a -- SR -- Core supply voltage 1.2 V VDD when external regulator is used with a disabled internal regulator (PMC unit turned-off, LVI monitor disabled) 1.14 1.2 1.32 V 4 Ivdd SR -- Voltage regulator core supply maximum DC output current4 400 -- -- mA 5 Vdd33 SR -- Regulated 3.3 V supply voltage when external regulator is used without disabling the internal regulator (PMC unit turned-on, internal 3.3V regulator enabled, LVI monitor active)5 3.3 3.45 3.6 V 5a -- SR -- Regulated 3.3 V supply voltage when external regulator is used with a disabled internal regulator (PMC unit turned-off, LVI monitor disabled) 3 3.3 3.6 V 6 -- SR -- Voltage regulator 3.3 V supply maximum required DC output current 80 -- -- mA 1 During start up operation the minimum required voltage to come out of reset state is 4.6 V. An internal regulator controller can be used to regulate core supply. 3 The minimum supply required for the part to exit reset and enter in normal run mode is 1.28 V. 4 The onchip regulator can support a minimum of 400 ma although the worst case core current is 180 ma. 5 An internal regulator can be used to regulate 3.3 V supply. 2 Table 14. PMC electrical characteristics ID Name C Parameter CC C Nominal bandgap voltage reference Min Typ Max Unit -- 1.219 -- V Vbg-7% Vbg Vbg+6% V 1 Vbg 1a -- CC P Untrimmed bandgap reference voltage 1b -- CC P Trimmed bandgap reference voltage (5 V, 27 C)1 Vbg-10mV Vbg Vbg+10mV V 1c -- CC C Bandgap reference temperature variation -- 100 -- ppm /C Notes MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 63 Electrical characteristics Table 14. PMC electrical characteristics (continued) ID Name C Parameter Min Typ Max Unit 1d -- CC C Bandgap reference supply voltage variation -- 3000 -- ppm /V 2 Vdd CC C Nominal VDD core supply internal regulator target DC output voltage2 -- 1.28 -- V 2a -- CC P Nominal VDD core supply internal regulator target DC output voltage variation at power-on reset Vdd - 6% Vdd Vdd + 10% V 2b -- CC P Nominal VDD core supply internal regulator target DC output voltage variation after power-on reset Vdd - 103 Vdd Vdd + 3% V 2c -- CC C Trimming step Vdd -- 20 -- mV 2d Ivrcctl CC C Voltage regulator controller for core supply maximum DC output current 20 -- -- mA 3 Lvi1p2 CC C Nominal LVI for rising core supply4,5 -- 1.160 -- V 3a -- CC C Variation of LVI for rising core supply at power-on reset5,6 1.120 1.200 1.280 V 3b -- CC C Variation of LVI for rising Lvi1p2-3% core supply after power-on reset5,6 Lvi1p2 Lvi1p2+3% V 3c -- CC C Trimming step LVI core supply5 -- 20 -- mV 3d Lvi1p2_h CC C LVI core supply hysteresis5 -- 40 -- mV 4 Por1.2V_r CC C POR 1.2 V rising -- 0.709 -- V 4a -- 4b Por1.2V_f 4c -- 5 5a CC C POR 1.2 V rising variation CC C POR 1.2 V falling Por1.2V_r- Por1.2V_r Por1.2V_r+ 35% 35% -- 0.638 -- Notes V V CC C POR 1.2 V falling variation Por1.2V_f- Por1.2V_f Por1.2V_f+ 35% 35% V Vdd33 CC C Nominal 3.3 V supply internal regulator DC output voltage -- 3.39 -- V -- CC P Nominal 3.3 V supply internal regulator DC output voltage variation at power-on reset6 Vdd33 - 8.5% Vdd33 Vdd3 + 7% V MPC5634M Microcontroller Data Sheet, Rev. 9 64 Freescale Semiconductor Electrical characteristics Table 14. PMC electrical characteristics (continued) ID Name C Parameter Min Typ Max Unit Vdd33 - 7.5% Vdd33 Vdd33 + 7% V Notes With internal load up to Idd3p3 5b -- CC P Nominal 3.3 V supply internal regulator DC output voltage variation after power-on reset 5c -- CC D Voltage regulator 3.3 V output impedance at maximum DC load -- -- 2 5d Idd3p3 CC P Voltage regulator 3.3 V maximum DC output current 80 -- -- mA 5e Vdd33 ILim6 CC C Voltage regulator 3.3 V DC current limit -- 130 -- mA 6 Lvi3p3 -- 3.090 -- V The Lvi3p3 specs are also valid for the Vddeh LVI 6a -- CC C Variation of LVI for rising 3.3 V supply at power-on reset5 Lvi3p3-6% Lvi3p3 Lvi3p3+6% V See note 7 6b -- CC C Variation of LVI for rising Lvi3p3-3% 3.3 V supply after power-on reset5 Lvi3p3 Lvi3p3+3% V See note 7 6c -- CC C Trimming step LVI 3.3 V5 -- 20 -- mV -- 60 -- mV -- 2.07 -- V CC C Nominal LVI for rising 3.3 V supply5 CC C LVI 3.3 V hysteresis 5 6d Lvi3p3_h 7 Por3.3V_r CC C Nominal POR for rising 3.3 V supply 7a -- CC C Variation of POR for rising 3.3 V supply 7b Por3.3V_f 7c -- 8 Lvi5p0 CC C Nominal LVI for rising 5 V VDDREG supply5 -- 4.290 -- V 8a -- CC C Variation of LVI for rising 5 V VDDREG supply at power-on reset5 Lvi5p0-6% Lvi5p0 Lvi5p0+6% V 8b -- CC C Variation of LVI for rising 5 V VDDREG supply power-on reset5 Lvi5p0-3% Lvi5p0 Lvi5p0+3% V 8c -- CC C Trimming step LVI 5 V5 -- 20 -- mV CC C Nominal POR for falling 3.3 V supply Por3.3V_r- Por3.3V_r Por3.3V_r+ 35% 35% -- 1.95 -- CC C Variation of POR for falling Por3.3V_f- Por3.3V_f Por3.3V_f+ 3.3 V supply 35% 35% The 3.3V POR specs are also valid for the Vddeh POR V V V MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 65 Electrical characteristics Table 14. PMC electrical characteristics (continued) ID 1 2 3 4 5 6 7 Name C Parameter Min Typ Max Unit 8d Lvi5p0_h CC C LVI 5 V hysteresis5 -- 60 -- mV 9 Por5V_r CC C Nominal POR for rising 5 V VDDREG supply -- 2.67 -- V 9a -- CC C Variation of POR for rising 5 V VDDREG supply Por5V_r - 35% Por5V_r Por5V_r + 50% V 9b Por5V_f CC C Nominal POR for falling 5 V VDDREG supply -- 2.47 -- V 9c -- CC C Variation of POR for falling 5 V VDDREG supply Por5V_f - 35% Por5V_f Por5V_f + 50% V Notes The limits will be reviewed after data collection from 3 different lots in a full production environment. Using external ballast transistor. Min range is extended to 10% since Lvi1p2 is reprogrammed from 1.2 V to 1.16 V after power-on reset. LVI for falling supply is calculated as LVI rising - LVI hysteresis. The internal voltage regulator can be disabled by tying the VDDREG pin to ground. When the internal voltage regulator is disabled, the LVI specifications are not applicable because all LVI monitors are disabled. POR specifications remain valid when the internal voltage regulator is disabled as long as VDDEH and VDD33 supplies are within the required ranges. This parameter is the "inrush" current of the internal 3.3V regulator when it is turned on. This spec. is the current at which the regulator will go into current limit mode. Lvi3p3 tracks DC target variation of internal Vdd33 regulator. Minimum and maximum Lvi3p3 correspond to minimum and maximum Vdd33 DC target respectively. MPC5634M Microcontroller Data Sheet, Rev. 9 66 Freescale Semiconductor Electrical characteristics 4.6.1 Regulator example 5V from power supply Keep inductance from 5V supply to the transistor collector and VDDREG below 1 H if not using RC CREG RC CC VDDREG Required only if RC is used T1 VRCCTL RB CB RE MCU Keep inductance below 20 nH VDD VSS CE CD Figure 7. Core voltage regulator controller external components preferred configuration There are three options for the bypassing and compensation networks for the 1.2V regulator controller. The component values in the following table are the same for all PMC network requirements. Table 15. Required external PMC component values Component Symbol Pass Transistor T1 VDDREG capacitor CREG Minimum Typical 1 RC Units Comment NJD2873 or BCP68 10 Pass transistor Collector CC bypass capacitor Collector resistor1 Maximum 1.1 -- F X7R, -50%/+35% 13.3 F X7R, -50%/+35% 5.6 The collector resistor may not be required. It depends on the allowable power dissipation of the pass transistor (T1). Table 16, Table 17 and Table 18 show the required component values for the three different options. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 67 Electrical characteristics Table 16. Network 1 component values Component Symbol Transistor emitter bypass CE capacitance RESR MCU decoupling capacitor Minimum Typical Maximum Units 4 x 2.35 4 x 4.7 4 x 6.35 F X7R, -50%/+35% 1x5 1 x 10 1 x 13.5 F X7R, -50%/+35% 50 m Equivalent ESR of CE capacitors 5 CD Comment 4 x 50 4 x 100 4 x 135 nF X7R, -50%/+35% Base "snubber" capacitor CB 1.1 2.2 2.97 F X7R, -50%/+35% Base "snubber" resistor RB 6.12 6.8 7.48 10% Emitter resistor RE 0 0 0 Not required (short) Table 17. Network 2 component values Component Symbol Transistor emitter bypass CE capacitance RESR MCU decoupling capacitor Minimum Typical Maximum Units 3 x 2.35 3 x 4.7 3 x 6.35 F X7R, -50%/+35% 1x5 1 x 10 1 x 13.5 F X7R, -50%/+35% 50 m Equivalent ESR of CE capacitors 5 CD Base "snubber" capacitor CB Comment 4 x 50 4 x 100 4 x 135 nF X7R, -50%/+35% 1.1 2.2 2.97 F X7R, -50%/+35% Base "snubber" resistor RB 9 10 11 10% Emitter resistor RE 0.252 0.280 0.308 Not required (short) The following component configuration is acceptable when using the BCP68 transistor, however, is not recommended for new designs. Either option 1 or option 2 should be used for new designs. This option should not be used with the NJD2873 transistor. Table 18. Network 3 component values Component Symbol Minimum Typical Maximum Units Transistor emitter bypass CE capacitance RESR 4 x 3.4 4 x 6.8 4 x 9.18 F X7R, -50%/+35% 50 m Equivalent ESR of CE capacitors MCU decoupling capacitor 4 x 110 4 x 220 4 x 297 nF X7R, -50%/+35% Base "snubber" capacitor CB 1.1 2.2 2.97 F X7R, -50%/+35% Base "snubber" resistor RB 13.5 15 16.5 10% Emitter resistor RE 0 0 0 Not required (short) CD 5 Comment MPC5634M Microcontroller Data Sheet, Rev. 9 68 Freescale Semiconductor Electrical characteristics 4.6.2 Recommended power transistors The following NPN transistors are recommended for use with the on-chip voltage regulator controller: ON SemiconductorTM BCP68T1 or NJD2873 as well as Philips SemiconductorTM BCP68. The collector of the external transistor is preferably connected to the same voltage supply source as the output stage of the regulator. Table 19. Recommended operating characteristics Symbol hFE () PD Parameter Value Unit 60 - 550 -- >1.0 (1.5 preferred) W 1.0 A DC current gain (Beta) Absolute minimum power dissipation ICMaxDC Minimum peak collector current VCESAT Collector-to-emitter saturation voltage VBE 1 4.7 200-600 Base-to-emitter voltage 0.4-1.0 1 mV V Adjust resistor at bipolar transistor collector for 3.3 V/5.0 V to avoid VCE < VCESAT Power up/down sequencing There is no power sequencing required among power sources during power up and power down, in order to operate within specification but use of the following sequence is strongly recommended when the internal regulator is bypassed: 5 V 3.3 V and 1.2 V This is also the normal sequence when the internal regulator is enabled. Although there are no power up/down sequencing requirements to prevent issues like latch-up, excessive current spikes, etc., the state of the I/O pins during power up/down varies according to table Table 20 for all pins with fast pads and Table 21 for all pins with medium, slow and multi-voltage pads.1 Table 20. Power sequence pin states for fast pads VDDE VRC33 VDD Fast (pad_fc) LOW X X LOW VDDE LOW X HIGH VDDE VRC33 LOW HIGH IMPEDANCE VDDE VRC33 VDD FUNCTIONAL Table 21. Power sequence pin states for medium, slow and multi-voltage pads VDDEH VDD Medium (pad_msr_hv) Slow (pad_ssr_hv) Multi-voltage (pad_multv_hv) LOW X LOW VDDEH LOW HIGH IMPEDANCE VDDEH VDD FUNCTIONAL 1.If an external 3.3V external regulator is used to supply current to the 1.2V pass transistor and this supply also supplies current for the other 3.3V supplies, then the 5V supply must always be greater than or equal to the external 3.3V supply. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 69 Electrical characteristics 4.8 DC electrical specifications Table 22. DC electrical specifications1 Value2 Symbol VDD C SR Parameter Conditions -- Core supply voltage -- Unit min typ max 1.14 -- 1.32 V 3 V VDDE SR -- I/O supply voltage -- 1.62 -- 3.6 VDDEH SR -- I/O supply voltage -- 3.0 -- 5.25 V VRC33 SR -- 3.3 V external voltage4 -- 3.0 -- 3.6 V -- 5.25 V VDDA SR -- Analog supply voltage 6 5 -- 4.75 -- VSSA - 0.3 -- VDDA+0.3 V VINDC SR -- Analog input voltage VSS - VSSA SR -- VSS differential voltage -- -100 -- 100 mV VRL SR -- Analog reference low voltage -- VSSA -- VSSA+0.1 V VRL - VSSA SR -- VRL differential voltage -- -100 -- 100 mV VRH SR -- Analog reference high voltage -- VDDA - 0.1 -- VDDA V VRH - VRL SR -- VREF differential voltage -- 4.75 -- 5.25 V VDDF SR -- Flash operating voltage 7 -- 1.14 -- 1.32 V VFLASH8 SR -- Flash read voltage -- 4.75 -- 5.25 V VSTBY SR -- SRAM standby voltage Unregulated mode 0.95 -- 1.2 V 2.0 -- 5.5 Regulated mode VDDREG SR -- Voltage regulator supply voltage9 -- 4.75 -- 5.25 V VDDPLL SR -- Clock synthesizer operating voltage -- 1.14 -- 1.32 V VSSPLL - VSS SR -- VSSPLL to VSS differential voltage -- -100 -- 100 mV VIL_S CC C Slow/medium pad I/O Hysteresis input low voltage enabled VSS-0.3 -- 0.35*VDDEH V P hysteresis disabled VSS-0.3 -- 0.40*VDDEH C Fast pad I/O input low Hysteresis voltage enabled VSS-0.3 -- 0.35*VDDE P VSS-0.3 -- 0.40*VDDE VIL_F CC hysteresis disabled V MPC5634M Microcontroller Data Sheet, Rev. 9 70 Freescale Semiconductor Electrical characteristics Table 22. DC electrical specifications1 (continued) Value2 Symbol VIL_LS VIL_HS VIH_S VIH_F VIH_LS VIH_HS C CC CC CC CC CC CC Parameter C Conditions Unit min typ max Multi-voltage pad I/O input low voltage in low-swing P mode10,11,12,13 Hysteresis enabled VSS-0.3 -- 0.8 Hysteresis disabled VSS-0.3 -- 1.1 C Multi-voltage pad I/O input low voltage in high-swing mode P Hysteresis enabled VSS-0.3 -- 0.35 VDDEH Hysteresis disabled VSS-0.3 -- 0.4 VDDEH C Slow/medium pad I/O Hysteresis input high voltage enabled 0.65 VDDEH -- VDDEH+0.3 P hysteresis disabled 0.55 VDDEH -- VDDEH+0.3 C Fast pad I/O input high Hysteresis voltage enabled 0.65 VDDE -- VDDE+0.3 P hysteresis disabled 0.55 VDDE -- VDDE+0.3 C Multi-voltage pad I/O input high voltage in low-swing P mode10,11,12,13,14 Hysteresis enabled 2.5 -- VDDEH+0.3 Hysteresis disabled 2.2 -- VDDEH+0.3 C Multi-voltage pad I/O input high voltage in high-swing mode15 P Hysteresis enabled 0.65 VDDEH -- VDDEH+0.3 Hysteresis disabled 0.55 VDDEH -- VDDEH+0.3 V V V V V V VOL_S CC P Slow/medium multi-voltage pad I/O output low voltage18,16 -- -- -- 0.2*VDDEH V VOL_F CC P Fast pad I/O output low voltage17,18 -- -- -- 0.2*VDDE V VOL_LS CC P Multi-voltage pad I/O output low voltage in low-swing mode10,11,12,13,17 IOL = 2 mA -- -- 0.6 V VOL_HS CC P Multi-voltage pad I/O output low voltage in high-swing mode17 -- -- -- 0.2 VDDEH V VOH_S CC P Slow/medium pad I/O output high voltage18,16 -- 0.8 VDDEH -- -- V VOH_F CC P Fast pad I/O output high voltage17,18 -- 0.8 VDDE -- -- V MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 71 Electrical characteristics Table 22. DC electrical specifications1 (continued) Value2 Symbol C Parameter Conditions Unit min typ max VOH_LS CC P Multi-voltage pad I/O output high voltage in low-swing mode10,11,12,13,17 IOH_LS = 0.5 mA Min VDDEH = 4.75 V 2.1 -- 3.7 V VOH_HS CC P Multi-voltage pad I/O output high voltage in high-swing mode17 -- 0.8 VDDEH -- -- V VHYS_S CC C Slow/medium/multi-vol tage I/O input hysteresis -- 0.1 * VDDEH -- -- V VHYS_F CC C Fast I/O input hysteresis -- 0.1 * VDDE -- -- V VHYS_LS CC C Low-Swing-Mode hysteresis Multi-Voltage I/O Input enabled Hysteresis 0.25 -- -- V IDD+IDDPLL19 CC P Operating current 1.2 V supplies VDD = 1.32 V, 80 MHz -- -- 195 mA CC P VDD = 1.32 V, 60 MHz -- -- 135 CC P VDD = 1.32 V, 40 MHz -- -- 98 CC -- -- 80 A CC T Operating current 1 V TJ = 25 oC supplies T TJ = 55 oC -- -- 100 A IDDSTBY150 CC P Operating current TJ=150 oC -- -- 700 A IDDSLOW IDDSTOP CC P VDD low-power mode operating current @ C 1.32 V Slow mode20 -- -- 50 mA mode21 -- -- 50 IDD33 CC T Operating current 3.3 V supplies @ 80 MHz VRC334,22 -- -- 70 mA IDDA IREF CC P Operating current 5.0 V supplies @ P 80 MHz VDDA -- -- 30 mA Analog reference supply current -- -- 1.0 VDDREG -- -- 70 IDDSTBY IDDREG C Stop MPC5634M Microcontroller Data Sheet, Rev. 9 72 Freescale Semiconductor Electrical characteristics Table 22. DC electrical specifications1 (continued) Value2 Symbol IDDH1 IDDH6 IDDH7 IDD7 IDDH9 IDD12 IACT_S IACT_F IACT_MV_PU IACT_MV_PD C CC CC CC CC CC Parameter Conditions Unit min typ max See note 23 mA A D Operating current 23 supplies @ V D DDE 80 MHz D VDDEH1 -- -- VDDEH6 -- -- VDDEH7 -- -- D VDDE7 -- -- D VDDEH9 -- -- D VDDE12 -- -- C Slow/medium I/O weak 3.0 V - 3.6 V pull up/down current24 P 4.75 V - 5.25 V 15 -- 95 35 -- 200 D Fast I/O weak pull up/down current24 1.62 V - 1.98 V 36 -- 120 D 2.25 V - 2.75 V 34 -- 139 D 3.0 V - 3.6 V 42 -- 158 C Multi-voltage pad weak VDDEH= pullup current 3.0-3.6 V10, pad_multv_hv, all process corners, high swing mode only 10 -- 75 P 25 -- 200 C Multivoltage pad weak VDDEH= pulldown current 3.0-3.6 V10, pad_multv_hv, all process corners, high swing mode only 10 -- 60 P 25 -- 200 4.75 V - 5.25 V 4.75 V - 5.25 V A A A IINACT_D CC P I/O input leakage current25 -- -2.5 -- 2.5 A IIC CC T DC injection current (per pin) -- -1.0 -- 1.0 mA IINACT_A CC P Analog input current, channel off, AN[0:7], AN38, AN3926 -- -250 -- 250 nA P Analog input current, channel off, all other analog pins (ANx)26 -- -150 -- 150 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 73 Electrical characteristics Table 22. DC electrical specifications1 (continued) Value2 Symbol CL C CC Parameter Conditions Unit min typ max D Load capacitance (fast DSC(PCR[8:9 I/O)27 ]) = 0b00 -- -- 10 D DSC(PCR[8:9 ]) = 0b01 -- -- 20 D DSC(PCR[8:9 ]) = 0b10 -- -- 30 D DSC(PCR[8:9 ]) = 0b11 -- -- 50 pF CIN CC D Input capacitance (digital pins) -- -- -- 7 pF CIN_A CC D Input capacitance (analog pins) -- -- -- 10 pF CIN_M CC D Input capacitance (digital and analog pins28) -- -- -- 12 pF RPUPD200K CC P Weak Pull-Up/Down Resistance29,30 200 k Option -- 130 -- 280 k RPUPDMATCH CC C 200K Option 2.5 % RPUPD100K CC P Weak Pull-Up/Down Resistance29,30 100 k Option 140 k RPUPDMATCH CC C 100K Option 2.5 % RPUPD5K CC D Weak Pull-Up/Down Resistance29 5 k Option TA (TL to TH) SR -- Operating temperature range - ambient (packaged) -- SR -- Slew rate on power supply pins 1 2 3 4 5 6 7 -2.5 -- 65 -- -2.5 5 V 5% supply 1.4 -- 7.5 k -- -40.0 -- 125.0 C -- -- -- 50 V/ms These specifications are design targets and subject to change per device characterization. TBD: To Be Defined. VDDE must be lower than VRC33, otherwise there is additional leakage on pins supplied by VDDE. These specifications apply when VRC33 is supplied externally, after disabling the internal regulator (VDDREG = 0). ADC is functional with 4 V VDDA 4.75 V but with derated accuracy. This means the ADC will continue to function at full speed with no bad behavior, but the accuracy will be degraded. Internal structures hold the input voltage less than VDDA + 1.0 V on all pads powered by VDDA supplies, if the maximum injection current specification is met (3 mA for all pins) and VDDA is within the operating voltage specifications. The VDDF supply is connected to VDD in the package substrate. This specification applies to calibration package devices only. MPC5634M Microcontroller Data Sheet, Rev. 9 74 Freescale Semiconductor Electrical characteristics 8 VFLASH is only available in the calibration package. Regulator is functional, with derated performance, with supply voltage down to 4.0 V. 10 Multi-voltage pads (type pad_multv_hv) must be supplied with a power supply between 4.75 V and 5.25 V. 11 The slew rate (SRC) setting must be 0b11 when in low-swing mode. 12 While in low-swing mode there are no restrictions in transitioning to high-swing mode. 13 Pin in low-swing mode can accept a 5 V input. 14 Values are pending characterization. 15 Pin in low-swing mode can accept a 5 V input. 16 Characterization based capability: IOH_S = {6, 11.6} mA and IOL_S = {9.2, 17.7} mA for {slow, medium} I/O with VDDEH=4.5 V; IOH_S = {2.8, 5.4} mA and IOL_S = {4.2, 8.1} mA for {slow, medium} I/O with VDDEH=3.0 V 17 Characterization based capability: IOH_F = {12, 20, 30, 40} mA and IOL_F = {24, 40, 50, 65} mA for {00, 01,10, 11} drive mode with VDDE=3.0 V; IOH_F = {7, 13, 18, 25} mA and IOL_F = {18, 30, 35, 50} mA for {00, 01, 10, 11} drive mode with VDDE=2.25 V; IOH_F = {3, 7, 10, 15} mA and IOL_F = {12, 20, 27, 35} mA for {00, 01, 10, 11} drive mode with VDDE=1.62 V 18 All VOL/VOH values 100% tested with 2 mA load. 19 Run mode as follows: System clock = 40/60/80 MHz + FM 2% Code executed from flash memory ADC0 at 16 MHz with DMA enabled ADC1 at 8 MHz eMIOS pads toggle in PWM mode with a rate between 100 kHz and 500 kHz eTPU pads toggle in PWM mode with a rate between 10 kHz and 500 kHz CAN configured for a bit rate of 500 kHz DSPI configured in master mode with a bit rate of 2 MHz eSCI transmission configured with a bit rate of 100 kHz 20 Bypass mode, system clock at 1 MHz (using system clock divider), PLL shut down, CPU running simple executive code, 4 x ADC conversion every 10 ms, 2 x PWM channels at 1 kHz, all other modules stopped. 21 Bypass mode, system clock at 1 MHz (using system clock divider), CPU stopped, PIT running, all other modules stopped. 22 When using the internal regulator only, a bypass capacitor should be connected to this pin. External circuits should not be powered by the internal regulator. The internal regulator can be used as a reference for an external debugger. 23 Power requirements for each I/O segment are dependent on the frequency of operation and load of the I/O pins on a particular I/O segment, and the voltage of the I/O segment. See Table 23 for values to calculate power dissipation for specific operation. The total power consumption of an I/O segment is the sum of the individual power consumptions for each pin on the segment. 24 Absolute value of current, measured at V and V . IL IH 25 Weak pull up/down inactive. Measured at V DDE = 3.6 V and VDDEH = 5.25 V. Applies to pad types: fast (pad_fc). 26 Maximum leakage occurs at maximum operating temperature. Leakage current decreases by approximately one-half for each 8 to 12 oC, in the ambient temperature range of 50 to 125 oC. Applies to pad types: pad_a and pad_ae. 27 Applies to CLKOUT, external bus pins, and Nexus pins. 28 Applies to the FCK, SDI, SDO, and SDS pins. 29 This programmable option applies only to eQADC differential input channels and is used for biasing and sensor diagnostics. 30 When the pull-up and pull-down of the same nominal 200 K or 100 K value are both enabled, assuming no interference from external devices, the resulting pad voltage will be 0.5*VDDE 2.5% 9 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 75 Electrical characteristics 4.9 I/O Pad current specifications NOTE MPC5634M devices use two sets of I/O pads (5 V and 3.3 V). See Table 2 and Table 3 in Section 3.6, "Signal summary, for the pad type associated with each signal. The power consumption of an I/O segment depends on the usage of the pins on a particular segment. The power consumption is the sum of all output pin currents for a particular segment. The output pin current can be calculated from Table 23 based on the voltage, frequency, and load on the pin. Use linear scaling to calculate pin currents for voltage, frequency, and load parameters that fall outside the values given in Table 23. Table 23. I/O pad average IDDE specifications1 Pad Type Slow Medium Fast MultiV (High Swing Mode) C Period (ns) Load2 (pF) VDDE (V) Drive/Slew Rate Select IDDE Avg (mA)3 IDDE RMS (mA) CC D 37 50 5.25 11 9 -- CC D 130 50 5.25 01 2.5 -- CC D 650 50 5.25 00 0.5 -- CC D 840 200 5.25 00 1.5 -- CC D 24 50 5.25 11 14 -- CC D 62 50 5.25 01 5.3 -- CC D 317 50 5.25 00 1.1 -- CC D 425 200 5.25 00 3 -- CC D 10 50 3.6 11 22.7 68.3 CC D 10 30 3.6 10 12.1 41.1 CC D 10 20 3.6 01 8.3 27.7 CC D 10 10 3.6 00 4.44 14.3 CC D 10 50 1.98 11 12.5 31 CC D 10 30 1.98 10 7.3 18.6 CC D 10 20 1.98 01 5.42 12.6 CC D 10 10 1.98 00 2.84 6.4 11 21.24 -- Symbol IDRV_SSR_HV IDRV_MSR_HV IDRV_FC IDRV_MULTV_HV CC CC IDRV_MULTV_HV D 15 30 50 50 5.25 5.25 10 5 -- 4 -- -- CC D 50 50 5.25 01 6.2 CC D 300 50 5.25 00 1.14 -- 00 4 -- CC MultiV (Low Swing Mode) D D CC D CC D 300 200 15 30 30 30 5.25 5.25 5.25 4.0 11 20.2 11 NA 6 -- -- 1 Numbers from simulations at best case process, 150 C. All loads are lumped. 3 Average current is for pad configured as output only. 2 MPC5634M Microcontroller Data Sheet, Rev. 9 76 Freescale Semiconductor Electrical characteristics 4 Ratio from 5.5 V pad spec to 5.25 V data sheet. Not specified. 6 Low swing mode is not a strong function of VDDE. 5 4.9.1 I/O pad VRC33 current specifications The power consumption of the VRC33 supply is dependent on the usage of the pins on all I/O segments. The power consumption is the sum of all output pin VRC33 currents for all I/O segments. The output pin VRC33 current can be calculated from Table 24 based on the voltage, frequency, and load on all medium, slow, and multv_hv pins. The output pin VRC33 current can be calculated from Table 25 based on the voltage, frequency, and load on all fast pins. Use linear scaling to calculate pin currents for voltage, frequency, and load parameters that fall outside the values given in Table 24 and Table 25. Table 24. I/O pad VRC33 average IDDE specifications1 Pad Type Slow Medium IDRV_SSR_HV IDRV_MSR_HV 3 (High IDRV_MULTV_HV MultiV Swing Mode) 4 C Period (ns) Load2 (pF) Slew Rate Select IDD33 Avg (A) IDD33 RMS (A) CC D 100 50 11 0.8 235.7 CC D 200 50 01 0.04 87.4 CC D 800 50 00 0.06 47.4 CC D 800 200 00 0.009 47 CC D 40 50 11 2.75 258 CC D 100 50 01 0.11 76.5 CC D 500 50 00 0.02 56.2 CC D 500 200 00 0.01 56.2 CC D 40 50 11 2.75 258 CC D 100 50 01 0.11 76.5 CC D 500 50 00 0.02 56.2 CC D 500 200 00 0.01 56.2 CC D 40 30 11 2.75 258 CC D 100 30 11 0.11 76.5 CC D 500 30 11 0.02 56.2 CC D 500 30 11 0.01 56.2 Symbol MultiV (Low IDRV_MULTV_HV Swing Mode) 1 These are typical values that are estimated from simulation and not tested. Currents apply to output pins only. 2 All loads are lumped. 3 Average current is for pad configured as output only. 4 In low swing mode, multi-voltage pads (pad_multv_hv) must operate in highest slew rate setting. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 77 Electrical characteristics Table 25. VRC33 pad average DC current1 Pad Type Fast C Period (ns) Load2 (pF) VRC33 (V) VDDE (V) Drive Select IDD33 Avg (A) IDD33 RMS (A) CC D 10 50 3.6 3.6 11 2.35 6.12 CC D 10 30 3.6 3.6 10 1.75 4.3 CC D 10 20 3.6 3.6 01 1.41 3.43 CC D 10 10 3.6 3.6 00 1.06 2.9 CC D 10 50 3.6 1.98 11 1.75 4.56 CC D 10 30 3.6 1.98 10 1.32 3.44 CC D 10 20 3.6 1.98 01 1.14 2.95 CC D 10 10 3.6 1.98 00 0.95 2.62 Symbol IDRV_FC 1 These are typical values that are estimated from simulation and not tested. Currents apply to output pins only. 2 All loads are lumped. 4.9.2 LVDS pad specifications LVDS pads are implemented to support the MSC (Microsecond Channel) protocol which is an enhanced feature of the DSPI module. The LVDS pads are compliant with LVDS specifications and support data rates up to 50 MHz. Table 26. DSPI LVDS pad specification 1, 2 # Characteristic Symbol C Condition Min. Value Typ. Value Max. Value Unit Data Rate 4 Data Frequency FLVDSCLK CC D 50 MHz Driver Specs 5 Differential output voltage VOD3 CC P SRC=0b00 or 0b11 150 430 CC P SRC=0b01 90 340 SRC=0b10 155 480 CC P CC P mV 6 Common mode voltage (LVDS), VOS VOS3 7 Rise/Fall time TR/TF CC D 2 ns 8 Propagation delay (Low to High) TPLH CC D 4 ns 9 Propagation delay (High to Low) TPHL CC D 4 ns tPDSYNC CC D 4 ns CC D 500 ns 10 Delay (H/L), sync Mode 11 Delay, Z to Normal (High/Low) TDZ 0.8 1.2 1.6 V MPC5634M Microcontroller Data Sheet, Rev. 9 78 Freescale Semiconductor Electrical characteristics Table 26. DSPI LVDS pad specification 1, 2 (continued) 12 Diff Skew Itphla-tplhbI or Itplhb-tphlaI TSKEW CC D 0.5 ns 105 150 C Termination 13 Trans. Line (differential Zo) CC D 95 14 Temperature CC D -40 100 1 These are typical values that are estimated from simulation. These specifications are subject to change per device characterization. 3 Preliminary target values. Actual specifications to be determined. 2 4.10 Oscillator and PLLMRFM electrical characteristics Table 27. PLLMRFM electrical specifications1 (VDDPLL =1.14 V to 1.32 V, VSS = VSSPLL = 0 V, TA = TL to TH) Value Symbol C Parameter Conditions Unit min max D PLL reference frequency range2 Crystal reference 4 20 C External reference 4 80 -- 4 16 MHz -- 256 512 MHz -- 16 80 MHz MHz fref_crystal fref_ext CC fpll_in CC P Phase detector input frequency range (after pre-divider) fvco CC P VCO frequency range3 frequency2 MHz fsys CC C On-chip PLL fsys CC T System frequency in bypass mode4 Crystal reference 4 20 P External reference 0 80 -- 1 / fsys ns Lower limit 1.6 3.7 MHz Upper limit 24 56 -- 1.2 75 MHz fSYS maximum -5 5 % fCLKO tCYC fLORL fLORH CC CC D System clock period D Loss of reference frequency -- window5 D 6,7 fSCM CC P Self-clocked mode frequency CJITTER CC T CLKOUT period Peak-to-peak (clock jitter8,9,10,11 edge to clock edge) T tcst VIHEXT CC CC UT Long-term jitter (avg. over 2 ms interval) T Crystal start-up time 12, 13 T EXTAL input high voltage T -- Mode14, Crystal 0.8 Vxtal 1.5V15 -6 6 ns -- 10 ms Vxtal + 0.4 -- V External Reference14, VRC33/2 + 0.4 16 VRC33 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 79 Electrical characteristics Table 27. PLLMRFM electrical specifications1 (VDDPLL =1.14 V to 1.32 V, VSS = VSSPLL = 0 V, TA = TL to TH) (continued) Value Symbol VILEXT C CC Parameter T EXTAL input low voltage T -- CC Conditions max Crystal Mode14, 0.65Vxtal1.25V15 -- Vxtal - 0.4 External Reference14, 0 VRC33/2 - 0.4 4 MHz 5 30 8 MHz 5 26 12 MHz 5 23 16 MHz 5 19 20 MHz 5 16 -- -- 200 s 16 T XTAL load capacitance12 12, 17 Unit min V pF tlpll CC P PLL lock time tdc CC T Duty cycle of reference -- 40 60 % fLCK CC T Frequency LOCK range -- -6 6 % fsys fUL CC T Frequency un-LOCK range -- -18 18 % fsys fCS fDS CC D Modulation Depth Center spread 0.25 4.0 %fsys D Down Spread -0.5 -8.0 fMOD CC -- 100 D Modulation frequency18 -- kHz 1 All values given are initial design targets and subject to change. Considering operation with PLL not bypassed. 3 f VCO is calculated as follows: -- In Legacy Mode fVCO = (fcrystal / (PREDIV + 1)) * (4 * (MFD + 4)) -- In Enhanced Mode fvco = (fcrystal / (EPREDIV + 1)) * (EMFD + 4) 4 All internal registers retain data at 0 Hz. 5 "Loss of Reference Frequency" window is the reference frequency range outside of which the PLL is in self clocked mode. 6 Self clocked mode frequency is the frequency that the PLL operates at when the reference frequency falls outside the fLOR window. 7 f VCO self clock range is 20-150 MHz. fSCM represents fSYS after PLL output divider (ERFD) of 2 through 16 in enhanced mode. 8 This value is determined by the crystal manufacturer and board design. 9 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f SYS. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the PLL circuitry via VDDPLL and VSSPLL and variation in crystal oscillator frequency increase the CJITTER percentage for a given interval. 10 Proper PC board layout procedures must be followed to achieve specifications. 11 Values are with frequency modulation disabled. If frequency modulation is enabled, jitter is the sum of C JITTER and either fCS or fDS (depending on whether center spread or down spread modulation is enabled). 12 This value is determined by the crystal manufacturer and board design. For 4 MHz to 20 MHz crystals specified for this PLL, load capacitors should not exceed these limits. For a 20 MHz crystal the maximum load should be 17 pF. 13 Proper PC board layout procedures must be followed to achieve specifications. 14 This parameter is guaranteed by design rather than 100% tested. 2 MPC5634M Microcontroller Data Sheet, Rev. 9 80 Freescale Semiconductor Electrical characteristics 15 Vxtal range is preliminary and subject to change pending characterization data. VIHEXT cannot exceed VRC33 in external reference mode. 17 This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the synthesizer control register (SYNCR). 18 Modulation depth will be attenuated from depth setting when operating at modulation frequencies above 50kHz. 16 4.11 Temperature sensor electrical characteristics Table 28. Temperature sensor electrical characteristics Value Symbol 4.12 C Parameter -- CC C Temperature monitoring range -- CC C Sensitivity -- CC P Accuracy Conditions TJ = -40 to 150 C Unit min typical max -40 -- 150 C -- 6.3 -- mV/C -10 -- 10 C eQADC electrical characteristics NOTE ADC performance is affected by several environmental elements, such as quality of the input signal source, presence of noise sources and quality of the PCB layout. The DC or Static parameters (DNL, INL, OFFSET, GAIN, and TUE) are measured using methods that provide a very accurate evaluation using averaging. The AC or Dynamic parameters (SNR, THD, SFDR, SINAD) are determined using a full scale peak-peak sinewave of 1kHz frequency at the input of the ADC. Table 29. eQADC conversion specifications (operating) Value Symbol C Parameter Unit min max 2 16 MHz 2 + 13 128 + 14 ADCLK cycles -- 10 s 1.25 -- mV fADCLK SR -- ADC clock (ADCLK) frequency CC CC D Conversion cycles TSR CC C Stop mode recovery time1 -- CC D Resolution2 OFFNC CC C Offset error without calibration 0 160 Counts OFFWC CC C Offset error with calibration -4 4 Counts GAINNC CC C Full scale gain error without calibration -160 0 Counts GAINWC CC C Full scale gain error with calibration -4 4 Counts IINJ CC T Disruptive input injection current 3, 4, 5, 6 -3 3 mA -4 4 Counts EINJ CC T Incremental error due to injection current6,7,8 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 81 Electrical characteristics Table 29. eQADC conversion specifications (operating) (continued) Value Symbol TUE8 C CC Parameter Unit min max -4 4 Counts -8 8 Counts C Total unadjusted error (TUE) at 8 MHz9 10 TUE16 CC C Total unadjusted error at 16 MHz SNR CC T Signal to Noise Ratio11 55.2 dB THD CC T Total Harmonic Distorsion 70.0 dB SFDR CC T Spurious Free Dynamic Range 65.0 dB SINAD CC T Signal to Noise and Distorsion 55.0 dB ENOB CC T Effective Number of Bits 8.8 Counts GAINVGA1 CC - Variable gain amplifier accuracy (gain=1) CC C CC C CC C CC GAINVGA2 INL DNL C 12 8 MHz ADC -4 4 Counts13 16 MHz ADC -8 8 Counts 8 MHz ADC -314 314 Counts 14 314 Counts 16 MHz ADC CC - Variable gain amplifier accuracy (gain=2) CC D CC D CC D CC D CC - Variable gain amplifier accuracy (gain=4)12 CC D CC D CC D CC DIFFmax CC DIFFmax2 8 MHz ADC -5 5 Counts 16 MHz ADC -8 8 Counts 8 MHz ADC -3 3 Counts 16 MHz ADC -3 3 Counts 8 MHz ADC -7 7 Counts 16 MHz ADC -8 8 Counts 8 MHz ADC -4 4 Counts D 16 MHz ADC -4 4 Counts PREGAIN set to 1X setting - (VRH VRL)/2 V CC C Maximum differential voltage (DANx+ - DANx-) or (DANx- DANx+) C PREGAIN set to 2X setting - (VRH VRL)/4 V DIFFmax4 CC C PREGAIN set to 4X setting - (VRH VRL)/8 V DIFFcmv CC C Differential input Common mode voltage (DANx- + DANx+)/215 (VRH VRL)/2 5% (VRH VRL)/2 + 5% V GAINVGA4 INL -3 12 DNL INL DNL 1 Stop mode recovery time is the time from the setting of either of the enable bits in the ADC Control Register to the time that the ADC is ready to perform conversions.Delay from power up to full accuracy = 8 ms. 2 At V RH - VRL = 5.12 V, one count = 1.25 mV. Without using pregain. 3 Below disruptive current conditions, the channel being stressed has conversion values of 0x3FF for analog inputs greater then VRH and 0x0 for values less then VRL. Other channels are not affected by non-disruptive conditions. MPC5634M Microcontroller Data Sheet, Rev. 9 82 Freescale Semiconductor Electrical characteristics 4 Exceeding limit may cause conversion error on stressed channels and on unstressed channels. Transitions within the limit do not affect device reliability or cause permanent damage. 5 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values using VPOSCLAMP = VDDA + 0.5 V and VNEGCLAMP = - 0.3 V, then use the larger of the calculated values. 6 Condition applies to two adjacent pins at injection limits. 7 Performance expected with production silicon. 8 All channels have same 10 k < Rs < 100 k; Channel under test has Rs=10 k; IINJ=IINJMAX,IINJMIN. 9 TUE is tested by averaging 10 samples. 10 TUE is tested by averaging three samples. 11 These values can be significantly improved by using three samples of averaging. Input frequency of 1 kHz was used as the reference for the Signal to Noise Ratio. 12 Variable gain is controlled by setting the PRE_GAIN bits in the ADC_ACR1-8 registers to select a gain factor of 1, 2, or 4. Settings are for differential input only. Tested at 1 gain. Values for other settings are guaranteed by as indicated. 13 At VRH - VRL = 5.12 V, one LSB = 1.25 mV. 14 Guaranteed 10-bit monotonicity. 15 Voltages between VRL and VRH will not cause damage to the pins. However, they may not be converted accurately if the differential voltage is above the maximum differential voltage. In addition, conversion errors may occur if the common mode voltage of the differential signal violates the Differential Input common mode voltage specification. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 83 Electrical characteristics 4.13 Platform flash controller electrical characteristics Table 30. APC, RWSC, WWSC settings vs. frequency of operation1 Target Max Frequency (MHz) APC2 RWSC2 WWSC 213 000 000 01 3 001 001 01 3 62 010 010 01 823 011 011 01 All 111 111 111 41 1 Illegal combinations exist, all entries must be taken from the same row APC must be equal to RWSC 3 Maximum Frequency includes FM modulation 2 4.14 Flash memory electrical characteristics Table 31. Program and erase specifications Symbol Parameter Min Value Typical Value1 Initial Max2 Max3 Unit Tdwprogram P Double Word (64 bits) Program Time4 -- 22 50 500 s T16kpperase P 16 KB Block Pre-program and Erase Time -- 300 500 5000 ms T32kpperase P 32 KB Block Pre-program and Erase Time -- 400 600 5000 ms T64kpperase P 64 KB Block Pre-program and Erase Time -- 600 900 5000 ms T128kpperase P 128 KB Block Pre-program and Erase Time -- 800 1300 7500 ms 1 Typical program and erase times assume nominal supply values and operation at 25 C. All times are subject to change pending device characterization. 2 Initial factory condition: < 100 program/erase cycles, 25 C, typical supply voltage. 3 The maximum program & erase times occur after the specified number of program/erase cycles. These maximum values are characterized but not guaranteed. 4 Actual hardware programming times. This does not include software overhead. MPC5634M Microcontroller Data Sheet, Rev. 9 84 Freescale Semiconductor Electrical characteristics Table 32. Flash module life Value Symbol Conditions Unit Min Typ -- P/E C Number of program/erase cycles per block for 16 Kbyte blocks over the operating temperature range (TJ) -- 100,000 P/E C Number of program/erase cycles per block for 32 and 64 Kbyte blocks over operating temperature range (TJ) -- 10,000 100,000 cycles P/E C Number of program/erase cycles per block for 128 Kbyte blocks over the operating temperature range (TJ) -- 1,000 100,000 cycles Blocks with 0 - 1,000 P/E cycles 20 -- years Blocks with 10,000 P/E cycles 10 -- years Blocks with 100,000 P/E cycles 5 -- years Retention 1 Parameter C Minimum data retention at 85 C average ambient temperature1 cycles Ambient temperature averaged over duration of application, not to exceed recommended product operating temperature range. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 85 Electrical characteristics 4.15 AC specifications 4.15.1 Pad AC specifications Table 33. Pad AC specifications (5.0 V)1,2 Name C Output Delay (ns)3,4 Low-to-High / High-to-Low Rise/Fall Edge ( )4,5 Min Max Min Max Drive Load SRC/DSC (pF) MSB,LSB CC D 4.6/3.7 12/12 2.2/2.2 7/7 50 CC D 13/10 32/32 9/9 22/22 200 1010 N/A Medium6,7,8 CC D 12/13 28/34 5.6/6 15/15 50 CC D 23/23 52/59 11/14 31/31 200 CC D 69/71 152/165 34/35 74/74 50 CC D 95/90 205/220 44/51 96/96 200 CC D 7.3/5.7 19/18 4.4/4.3 14/14 50 CC D 24/19 58/58 17/15 42/42 200 CC D 26/27 61/69 13/13 34/34 50 CC D 49/45 115/115 27/23 61/61 200 CC D 137/142 320/330 72/74 164/164 50 CC D 182/172 420/420 90/85 200/200 200 CC D 4.1/3.6 10.3/8.9 3.28/2.98 8/8 50 CC D 10.4/10.2 24.2/23.6 12.7/11.54 29/29 200 119 01 00 119 CC D 8.38/6.11 16/12.9 5.48/4.81 11/11 50 CC D 15.9/13.6 31/28.5 14.6/13.1 31/31 200 CC D 61.7/10.4 92.2/24.3 42.0/12.2 63/63 50 85.5/37.3 132.6/ 78.9 57.7/46.4 85/85 200 2.31/2.34 7.62/6.33 1.26/1.67 7/7 30 119 CC MultiV (Low Swing Mode) 00 1010 N/A MultiV12 (High Swing Mode) 01 1010 N/A Slow8,11 119 CC D D Fast13 01 00 N/A pad_i_hv14 CC D 0.5/0.5 1.9/1.9 0.3/0.3 1.5/1.5 0.5 N/A pull_hv CC D NA 6000 -- 5000/5000 50 N/A 1 These are worst case values that are estimated from simulation and not tested. Values in the table are simulated at fSYS = 80 MHz, VDD = 1.14 V to 1.32 V, VDDE = 1.62 V to 1.98 V, VDDEH = 4.5 V to 5.25 V, TA = TL to TH. 2 TBD: To Be Defined. MPC5634M Microcontroller Data Sheet, Rev. 9 86 Freescale Semiconductor Electrical characteristics 3 This parameter is supplied for reference and is not guaranteed by design and not tested. Delay and rise/fall are measured to 20% or 80% of the respective signal. 5 This parameter is guaranteed by characterization before qualification rather than 100% tested. 6 In high swing mode, high/low swing pad Vol and Voh values are the same as those of the slew controlled output pads 7 Medium Slew-Rate Controlled Output buffer. Contains an input buffer and weak pullup/pulldown. 8 Output delay is shown in Figure 8. Add a maximum of one system clock to the output delay for delay with respect to system clock. 9 Can be used on the tester. 10 This drive select value is not supported. If selected, it will be approximately equal to 11. 11 Slow Slew-Rate Controlled Output buffer. Contains an input buffer and weak pullup/pulldown. 12 Selectable high/low swing IO pad with selectable slew in high swing mode only. 13 Fast pads are 3.3 V pads. 14 Stand alone input buffer. Also has weak pull-up/pull-down. 4 Table 34. Pad AC specifications (3.3 V)1 Pad Type Medium5,6,7 C Output Delay (ns)2,3 Low-to-High / High-to-Low Rise/Fall Edge (ns)3,4 Min Max Min Max Drive Load (pF) MSB,LSB CC D 5.8/4.4 18/17 2.7/2.1 10/10 50 CC D 16/13 46/49 11.2/8.6 34/34 200 Slow CC D 14/16 37/45 6.5/6.7 19/19 50 CC D 27/27 69/82 15/13 43/43 200 CC D 83/86 200/210 38/38 86/86 50 CC D 113/109 270/285 53/46 120/120 200 CC D 9.2/6.9 27/28 5.5/4.1 20/20 50 CC D 30/23 81/87 21/16 63/63 200 MultiV (High Swing Mode) 01 00 11 109 N/A 7,11 118 109 N/A 7,10 SRC/DSC CC D 31/31 80/90 15.4/15.4 42/42 50 CC D 58/52 144/155 32/26 82/85 200 CC D 162/168 415/415 80/82 190/190 50 CC D 216/205 533/540 106/95 250/250 200 CC D 3.7/3.1 10/10 30 CC D 46/49 37/37 200 01 00 118 109 N/A CC D 32 15/15 50 CC D 72 46/46 200 CC D 210 100/100 50 CC D 295 134/134 200 01 00 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 87 Electrical characteristics Table 34. Pad AC specifications (3.3 V)1 (continued) Pad Type C Output Delay (ns)2,3 Low-to-High / High-to-Low Min Max Rise/Fall Edge (ns)3,4 Min Drive Load (pF) Max SRC/DSC MSB,LSB CC D 2.5/2.5 1.2/1.2 10 00 CC D 2.5/2.5 1.2/1.2 20 01 CC D 2.5/2.5 1.2/1.2 30 10 CC D 2.5/2.5 1.2/1.2 50 118 pad_i_hv12 CC D 0.5/0.5 3/3 1.5/1.5 0.5 N/A pull_hv CC D NA 6000 5000/5000 50 N/A Fast 0.4/0.4 1 These are worst case values that are estimated from simulation and not tested. The values in the table are simulated at fSYS = 80 MHz, VDD = 1.14 V to 1.32 V, VDDE = 3 V to 3.6 V, VDDEH = 3 V to 3.6 V, TA = TL to TH. 2 This parameter is supplied for reference and is not guaranteed by design and not tested. 3 Delay and rise/fall are measured to 20% or 80% of the respective signal. 4 This parameter is guaranteed by characterization before qualification rather than 100% tested. 5 In high swing mode, high/low swing pad Vol and Voh values are the same as those of the slew controlled output pads 6 Medium Slew-Rate Controlled Output buffer. Contains an input buffer and weak pullup/pulldown. 7 Output delay is shown in Figure 8. Add a maximum of one system clock to the output delay for delay with respect to system clock. 8 Can be used on the tester 9 This drive select value is not supported. If selected, it will be approximately equal to 11. 10 Slow Slew-Rate Controlled Output buffer. Contains an input buffer and weak pullup/pulldown. 11 Slow Slew-Rate Controlled Output buffer. Contains an input buffer and weak pullup/pulldown. 12 Stand alone input buffer. Also has weak pull-up/pull-down. Table 35. Pad AC specifications (1.8 V) Pad Type C Output Delay (ns)1,2 Low-to-High / High-to-Low Min Fast Rise/Fall Edge (ns)3 Max Min Drive Load (pF) Max SRC/DSC MSB,LSB CC D 3.0/3.0 2.0/1.5 10 00 CC D 3.0/3.0 2.0/1.5 20 01 CC D 3.0/3.0 2.0/1.5 30 10 CC D 3.0/3.0 2.0/1.5 50 114 1 This parameter is supplied for reference and is not guaranteed by design and not tested. Delay and rise/fall are measured to 20% or 80% of the respective signal. 3 This parameter is guaranteed by characterization before qualification rather than 100% tested. 4 Can be used on the tester. 2 MPC5634M Microcontroller Data Sheet, Rev. 9 88 Freescale Semiconductor Electrical characteristics VDDE/2 Pad Data Input Rising Edge Output Delay Falling Edge Output Delay VOH Pad Output VOL Figure 8. Pad output delay 4.16 AC timing 4.16.1 IEEE 1149.1 interface timing Table 36. JTAG pin AC electrical characteristics1 # Symbol C Characteristic Min. Value Max. Value Unit 1 tJCYC CC D TCK Cycle Time 100 -- ns 2 tJDC CC D TCK Clock Pulse Width 40 60 ns 3 tTCKRISE CC D TCK Rise and Fall Times (40% - 70%) -- 3 ns 4 tTMSS, tTDIS CC D TMS, TDI Data Setup Time 5 -- ns 5 tTMSH, tTDIH CC D TMS, TDI Data Hold Time 25 -- ns 6 tTDOV CC D TCK Low to TDO Data Valid -- 23 ns 7 tTDOI CC D TCK Low to TDO Data Invalid 0 -- ns 8 tTDOHZ CC D TCK Low to TDO High Impedance -- 20 ns 9 tJCMPPW CC D JCOMP Assertion Time 100 -- ns 10 tJCMPS CC D JCOMP Setup Time to TCK Low 40 -- ns 11 tBSDV CC D TCK Falling Edge to Output Valid -- 50 ns MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 89 Electrical characteristics Table 36. JTAG pin AC electrical characteristics1 (continued) # 1 Symbol C Characteristic Min. Value Max. Value Unit 12 tBSDVZ CC D TCK Falling Edge to Output Valid out of High Impedance -- 50 ns 13 tBSDHZ CC D TCK Falling Edge to Output High Impedance -- 50 ns 14 tBSDST CC D Boundary Scan Input Valid to TCK Rising Edge 50 -- ns 15 tBSDHT CC D TCK Rising Edge to Boundary Scan Input Invalid 50 -- ns JTAG timing specified at VDD = 1.14 V to 1.32 V, VDDEH = 4.5 V to 5.25 V with multi-voltage pads programmed to Low-Swing mode, TA = TL to TH, and CL = 30 pF with DSC = 0b10, SRC = 0b00. These specifications apply to JTAG boundary scan only. See Table 37 for functional specifications. TCK 2 3 2 1 3 Figure 9. JTAG test clock input timing MPC5634M Microcontroller Data Sheet, Rev. 9 90 Freescale Semiconductor Electrical characteristics TCK 4 5 TMS, TDI 6 8 7 TDO Figure 10. JTAG test access port timing TCK 10 JCOMP 9 Figure 11. JTAG JCOMP timing MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 91 Electrical characteristics TCK 11 13 Output Signals 12 Output Signals 14 15 Input Signals Figure 12. JTAG boundary scan timing 4.16.2 Nexus timing Table 37. Nexus debug port timing1 # 1 Symbol tMCYC CC C Characteristic Min. Value Max. Value Unit D MCKO Cycle Time 22,3 8 tCYC 1004 -- ns 40 60 % - 0.1 0.2 tMCYC 0.1 0.2 tMCYC - 0.1 0.2 tMCYC 1a tMCYC CC D Absolute Minimum MCKO Cycle Time 2 tMDC CC D MCKO Duty Cycle 5 3 tMDOV CC D MCKO Low to MDO Data Valid 4 tMSEOV CC D MCKO Low to MSEO Data Valid5 Valid5 6 tEVTOV CC D MCKO Low to EVTO Data 7 tEVTIPW CC D EVTI Pulse Width 4.0 -- tTCYC 8 tEVTOPW CC D EVTO Pulse Width 1 -- tMCYC MPC5634M Microcontroller Data Sheet, Rev. 9 92 Freescale Semiconductor Electrical characteristics Table 37. Nexus debug port timing1 (continued) # 9 1 2 3 4 5 6 7 8 Symbol tTCYC CC C Characteristic Min. Value Max. Value Unit D TCK Cycle Time 46,7 -- tCYC 1008 -- ns 9a tTCYC CC D Absolute Minimum TCK Cycle Time 10 tTDC CC D TCK Duty Cycle 40 60 % 11 tNTDIS CC D TDI Data Setup Time 5 -- ns 12 tNTDIH CC D TDI Data Hold Time 25 -- ns 13 tNTMSS CC D TMS Data Setup Time 5 -- ns 14 tNTMSH CC D TMS Data Hold Time 25 -- ns 15 tJOV CC D TCK Low to TDO Data Valid 10 20 ns All Nexus timing relative to MCKO is measured from 50% of MCKO and 50% of the respective signal. Nexus timing specified at VDD = 1.14 V to 1.32 V, VDDEH = 4.5 V to 5.25 V with multi-voltage pads programmed to Low-Swing mode, TA = TL to TH, and CL = 30 pF with DSC = 0b10. Achieving the absolute minimum MCKO cycle time may require setting the MCKO divider to more than its minimum setting (NPC_PCR[MCKO_DIV] depending on the actual system frequency being used. This is a functionally allowable feature. However, this may be limited by the maximum frequency specified by the Absolute minimum MCKO period specification. This may require setting the MCKO divider to more than its minimum setting (NPC_PCR[MCKO_DIV]) depending on the actual system frequency being used. MDO, MSEO, and EVTO data is held valid until next MCKO low cycle. Achieving the absolute minimum TCK cycle time may require a maximum clock speed (system frequency / 8) that is less than the maximum functional capability of the design (system frequency / 4) depending on the actual system frequency being used. This is a functionally allowable feature. However, this may be limited by the maximum frequency specified by the Absolute minimum TCK period specification. This may require a maximum clock speed (system frequency / 8) that is less than the maximum functional capability of the design (system frequency / 4) depending on the actual system frequency being used. 1 2 MCKO 3 4 6 MDO MSEO EVTO Output Data Valid Figure 13. Nexus output timing MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 93 Electrical characteristics TCK EVTI EVTO 9 7 7 8 8 Figure 14. Nexus event trigger and test clock timings TCK 11 13 12 14 TMS, TDI 15 TDO Figure 15. Nexus TDI, TMS, TDO timing MPC5634M Microcontroller Data Sheet, Rev. 9 94 Freescale Semiconductor Electrical characteristics 4.16.3 Calibration bus interface timing Table 38. Calibration bus operation timing 1 66 MHz (ext. bus)2 # Symbol C Characteristic Unit Min Max 1 TC CC P CLKOUT Period 15.2 -- ns 2 tCDC CC D CLKOUT duty cycle 45% 55% TC ns Notes Signals are measured at 50% VDDE. 3 tCRT CC D CLKOUT rise time -- 3 4 tCFT CC D CLKOUT fall time -- 3 ns 5 tCOH CC D CLKOUT Posedge to Output Signal Invalid or High Z(Hold Time) 1.04/1.5 -- ns Hold time selectable via SIU_ECCR[EBTS] bit: EBTS=0: 1.0ns EBTS=1: 1.5ns -- 6.04/7.0 ns Output valid time selectable via SIU_ECCR[EBTS] bit: EBTS=0: 5.5ns EBTS=1: 6.5ns 5.0 -- ns 1.0 -- ns 6.5 -- ns 3 -- ns ADDR[8:31] CS[0:3] DATA[0:31] OE RD_WR TS WE[0:3]/BE[0:3] 6 tCOV CC D CLKOUT Posedge to Output Signal Valid (Output Delay) ADDR[8:31] CS[0:3] DATA[0:31] OE RD_WR TS WE[0:3]/BE[0:3] 7 tCIS CC D Input Signal Valid to CLKOUT Posedge (Setup Time) DATA[0:31] 8 tCIH CC D CLKOUT Posedge to Input Signal Invalid (Hold Time) DATA[0:31] 9 10 1 2 3 4 5 tAPW tAAI CC CC D ALE Pulse Width5 D ALE Negated to Address Invalid5 Calibration bus timing specified at fSYS = 80 MHz, VDD = 1.14 V to 1.32 V, VDDE = 1.62 V to 3.6 V (unless stated otherwise), TA = TL to TH, and CL = 30 pF with DSC = 0b10. The external bus is limited to half the speed of the internal bus. The maximum external bus frequency is 66 MHz. Refer to Fast Pad timing in Table 34 and Table 35 (different values for 3.3 V vs. 1.8 V). The EBTS=0 timings are only valid/ tested at VDDE=2.25-3.6 V, whereas EBTS=1 timings are valid/tested at 1.6-3.6 V. Measured at 50% of ALE. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 95 Electrical characteristics Voh_f VDDE/2 CLKOUT Vol_f 2 3 2 4 1 Figure 16. CLKOUT timing VDDE/2 CLKOUT 6 5 VDDE/2 5 OUTPUT BUS VDDE/2 6 5 5 OUTPUT SIGNAL VDDE/2 6 OUTPUT SIGNAL VDDE/2 Figure 17. Synchronous output timing MPC5634M Microcontroller Data Sheet, Rev. 9 96 Freescale Semiconductor Electrical characteristics CLKOUT VDDE/2 7 8 INPUT BUS VDDE/2 7 8 INPUT SIGNAL VDDE/2 Figure 18. Synchronous input timing ipg_clk CLKOUT ALE TS A/D DATA ADDR 9 10 Figure 19. ALE signal timing MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 97 Electrical characteristics 4.16.4 eMIOS timing Table 39. eMIOS timing1 # 1 Symbol C Characteristic Min. Value Max. Value Unit 1 tMIPW CC D eMIOS Input Pulse Width 4 -- tCYC 2 tMOPW CC D eMIOS Output Pulse Width 1 -- tCYC eMIOS timing specified at fSYS = 80 MHz, VDD = 1.14 V to 1.32 V, VDDEH = 4.5 V to 5.25 V, TA = TL to TH, and CL = 50 pF with SRC = 0b00. 4.16.5 DSPI timing Table 40. DSPI timing1,2 40 MHz # 1 Symbol tSCK CC C 60 MHz 80 MHz Characteristic D SCK Cycle Time3,4 Delay5 Unit Min. Max. Min. Max. Min. Max. 48.8 ns 5.8 ms 28.4 ns 3.5 ms 24.4 ns 2.9 ms -- 46 -- 26 -- 22 -- ns 45 -- 25 -- 21 -- ns 2 tCSC CC D PCS to SCK 3 tASC CC D After SCK Delay6 4 tSDC CC D SCK Duty Cycle 5 tA CC D Slave Access Time (SS active to SOUT driven) -- 25 -- 25 -- 25 ns 6 tDIS CC D Slave SOUT Disable Time (SS inactive to SOUT High-Z or invalid) -- 25 -- 25 -- 25 ns 7 tPCSC CC D PCSx to PCSS time 4 -- 4 -- 4 -- ns 8 tPASC CC D PCSS to PCSx time 5 -- 5 -- 5 -- ns 9 tSUI CC ns (1/2tSC) - (1/2tSC) + (1/2tSC) - (1/2tSC) + (1/2tSC) - (1/2tSC) + 2 2 2 2 2 2 ns Data Setup Time for Inputs D Master (MTFE = 0) 20 -- 20 -- 20 -- D Slave 2 -- 2 -- 2 -- D Master (MTFE = 1, CPHA = 0)7 -4 -- 6 -- 8 -- D Master (MTFE = 1, CPHA = 1) 20 -- 20 -- 20 -- MPC5634M Microcontroller Data Sheet, Rev. 9 98 Freescale Semiconductor Electrical characteristics Table 40. DSPI timing1,2 (continued) 40 MHz # Symbol C 11 12 1 2 3 4 5 6 7 tHI tSUO tHO 80 MHz Unit Min. 10 60 MHz Characteristic CC Max. Min. Max. Min. Max. Data Hold Time for Inputs D Master (MTFE = 0) -4 -- -4 -- -4 -- D Slave 7 -- 7 -- 7 -- D Master (MTFE = 1, CPHA = 0)7 45 -- 25 -- 21 -- D Master (MTFE = 1, CPHA = 1) -4 -- -4 -- -4 -- CC ns Data Valid (after SCK edge) D Master (MTFE = 0) -- 6 -- 6 -- 6 D Slave -- 25 -- 25 -- 25 D Master (MTFE = 1, CPHA=0) -- 45 -- 25 -- 21 D -- 6 -- 6 -- 6 Master (MTFE = 1, CPHA=1) CC ns Data Hold Time for Outputs D Master (MTFE = 0) -5 -- -5 -- -5 -- D Slave 5.5 -- 5.5 -- 5.5 -- D Master (MTFE = 1, CPHA = 0) 8 -- 4 -- 3 -- D Master (MTFE = 1, CPHA = 1) -5 -- -5 -- -5 -- ns All DSPI timing specifications use the fastest slew rate (SRC = 0b11) on pad type M or MH. DSPI signals using pad types of S or SH have an additional delay based on the slew rate. DSPI timing is specified at VDDEH = 3.0-5.25 V, TA = TL to TH, and CL = 50 pF with SRC = 0b11. Speed is the nominal maximum frequency. Max speed is the maximum speed allowed including frequency modulation (FM). 42 MHz parts allow for 40 MHz system clock + 2% FM; 62 MHz parts allow for a 60 MHz system clock + 2% FM, and 82 MHz parts allow for 80 MHz system clock + 2% FM. The minimum DSPI Cycle Time restricts the baud rate selection for given system clock rate. These numbers are calculated based on two MPC5634M devices communicating over a DSPI link. The actual minimum SCK cycle time is limited by pad performance. The maximum value is programmable in DSPI_CTARx[PSSCK] and DSPI_CTARx[CSSCK]. The maximum value is programmable in DSPI_CTARx[PASC] and DSPI_CTARx[ASC]. This number is calculated assuming the SMPL_PT bitfield in DSPI_MCR is set to 0b10. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 99 Electrical characteristics 2 3 These numbers reference Table 40. PCSx 1 4 SCK Output (CPOL=0) 4 SCK Output (CPOL=1) 9 SIN 10 First Data Last Data Data 12 SOUT First Data 11 Data Last Data Figure 20. DSPI classic SPI timing - master, CPHA = 0 These numbers reference Table 40. PCSx SCK Output (CPOL=0) 10 SCK Output (CPOL=1) 9 SIN Data First Data 12 SOUT First Data Last Data 11 Data Last Data Figure 21. DSPI classic SPI timing - master, CPHA = 1 MPC5634M Microcontroller Data Sheet, Rev. 9 100 Freescale Semiconductor Electrical characteristics These numbers reference Table 40. 3 2 SS 1 4 SCK Input (CPOL=0) 4 SCK Input (CPOL=1) 5 First Data SOUT 9 6 Data Last Data Data Last Data 10 First Data SIN 11 12 Figure 22. DSPI classic SPI timing - slave, CPHA = 0 SS These numbers reference Table 40. SCK Input (CPOL=0) SCK Input (CPOL=1) 11 5 12 SOUT First Data 9 SIN Data Last Data Data Last Data 6 10 First Data Figure 23. DSPI classic SPI timing - slave, CPHA = 1 MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 101 Electrical characteristics These numbers reference Table 40. 3 PCSx 4 1 2 SCK Output (CPOL=0) 4 SCK Output (CPOL=1) 9 SIN 10 First Data 12 SOUT Last Data Data 11 First Data Data Last Data Figure 24. DSPI modified transfer format timing - master, CPHA = 0 These numbers reference Table 40. PCSx SCK Output (CPOL=0) SCK Output (CPOL=1) 10 9 SIN First Data Data 12 SOUT First Data Data Last Data 11 Last Data Figure 25. DSPI modified transfer format timing - master, CPHA = 1 MPC5634M Microcontroller Data Sheet, Rev. 9 102 Freescale Semiconductor Electrical characteristics These numbers reference Table 40. 3 2 SS 1 SCK Input (CPOL=0) 4 4 SCK Input (CPOL=1) First Data SOUT Data 6 Last Data 10 9 Data First Data SIN 12 11 5 Last Data Figure 26. DSPI modified transfer format timing - slave, CPHA =0 These numbers reference Table 40. SS SCK Input (CPOL=0) SCK Input (CPOL=1) 11 5 12 First Data SOUT 9 Last Data Data Last Data 10 First Data SIN Data 6 Figure 27. DSPI modified transfer format timing - slave, CPHA =1 7 8 PCSS PCSx Figure 28. DSPI PCS strobe (PCSS) timing MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 103 Electrical characteristics 4.16.6 eQADC SSI timing Table 41. eQADC SSI timing characteristics (pads at 3.3 V or at 5.0 V)1 CLOAD = 25pF on all outputs. Pad drive strength set to maximum. # Symbol C Rating Min Typ Max Unit 1/17 fSYS_CLK 12 fSYS_CLK Hertz 2 tSYS_CLK 17tSYS_CLK seconds 1 fFCK CC D FCK Frequency 2, 3 1 tFCK CC D FCK Period (tFCK = 1/ fFCK) 2 tFCKHT CC D Clock (FCK) High Time tSYS_CLK 6.5 9* tSYS_CLK 6.5 ns 3 tFCKLT CC D Clock (FCK) Low Time tSYS_CLK 6.5 8* tSYS_CLK 6.5 ns 4 tSDS_LL CC D SDS Lead/Lag Time -7.5 +7.5 ns 5 tSDO_LL CC D SDO Lead/Lag Time -7.5 +7.5 ns 6 tDVFE CC D Data Valid from FCK Falling Edge (tFCKLT+tSDO_LL) 1 ns 7 tEQ_SU CC D eQADC Data Setup Time (Inputs) 22 ns 8 tEQ_HO CC D eQADC Data Hold Time (Inputs) 1 ns 1 SS timing specified at fSYS = 80 MHz, VDD = 1.14 V to 1.32 V, VDDEH = 4.5 V to 5.25 V, TA = TL to TH, and CL = 50 pF with SRC = 0b00. 2 Maximum operating frequency is highly dependent on track delays, master pad delays, and slave pad delays. 3 FCK duty is not 50% when it is generated through the division of the system clock by an odd number. 1 2 3 FCK 4 4 SDS 5 SDO 25th 6 1st (MSB) 5 2nd 26th External Device Data Sample at FCK Falling Edge 8 7 SDI 1st (MSB) 2nd 25th 26th eQADC Data Sample at FCK Rising Edge Figure 29. eQADC SSI timing MPC5634M Microcontroller Data Sheet, Rev. 9 104 Freescale Semiconductor Packages 5 Packages 5.1 Package mechanical data 5.1.1 144 LQFP MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 105 Packages Figure 30. 144 LQFP package mechanical drawing (part 1) MPC5634M Microcontroller Data Sheet, Rev. 9 106 Freescale Semiconductor Packages Figure 31. 144 LQFP package mechanical drawing (part 2) MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 107 Packages Figure 32. 144 LQFP package mechanical drawing (part 3) MPC5634M Microcontroller Data Sheet, Rev. 9 108 Freescale Semiconductor Packages 5.1.2 176 LQFP 176 Figure 33. 176 LQFP package mechanical drawing (part 1) MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 109 Packages Figure 34. 176 LQFP package mechanical drawing (part 2) MPC5634M Microcontroller Data Sheet, Rev. 9 110 Freescale Semiconductor Packages Figure 35. 176 LQFP package mechanical drawing (part 3) MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 111 Packages 5.1.3 208 MAPBGA Figure 36. 208 MAPBGA package mechanical drawing (part 1) MPC5634M Microcontroller Data Sheet, Rev. 9 112 Freescale Semiconductor Packages Figure 37. 208 MAPBGA package mechanical drawing (part 2) MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 113 Ordering information 6 Ordering information Table 42 shows the orderable part numbers for the MPC5634M series. Table 42. Orderable part number summary Flash/SRAM (Kbytes) Package Speed (MHz) SPC5632MF2MLQ60 768 / 48 144 LQFP Pb-free 60 SPC5632MF2MLQ40 768 / 48 144 LQFP Pb-free 40 SPC5633MF2MMG80 1024 / 64 208 MAPBGA Pb-free 80 SPC5633MF2MLU80 1024 / 64 176 LQFP Pb-free 80 SPC5633MF2MLQ80 1024 / 64 144 LQFP Pb-free 80 SPC5633MF2MMG60 1024 / 64 208 MAPBGA Pb-free 60 SPC5633MF2MLU60 1024 / 64 176 LQFP Pb-free 60 SPC5633MF2MLQ60 1024 / 64 144 LQFP Pb-free 60 SPC5633MF2MLQ40 1024 / 64 144 LQFP Pb-free 40 SPC5634MF2MMG80 1536 / 94 208 MAPBGA Pb-free 80 SPC5634MF2MLU80 1536 / 94 176 LQFP Pb-free 80 SPC5634MF2MLQ80 1536 / 94 144 LQFP Pb-free 80 SPC5634MF2MMG60 1536 / 94 208 MAPBGA Pb-free 60 SPC5634MF2MLU60 1536 / 94 176 LQFP Pb-free 60 SPC5634MF2MLQ60 1536 / 94 144 LQFP Pb-free 60 Part Number SPC563M60L3CPBY SPC563M60L3CPAY MPC5634M Microcontroller Data Sheet, Rev. 9 114 Freescale Semiconductor Ordering information Example code: M PC 56 3 4 M F2 M LU 80 R Qualification Status Power Architecture Core Automotive Platform Core Version Flash Size (core dependent) Product Fab/Mask rev. Temperature Spec. Package Code Maximum Frequency Tape and Reel Qualification Status Flash Size (z3 core) Package Code M = MC status S = Auto qualified P = PC status 2 = 768 KB 4 = 1.5 MB LQ = 144 LQFP LU = 176 LQFP MG = 208 MAPBGA Automotive Platform Product Family Maximum Frequency 3 = 1 MB 56 = Power Architecture in 90 nm 57 = Power Architecture in 55 nm Core Version 3 = e200z3 M = MPC5634M Fab/Mask rev. 40 = 40 MHz 60 = 60 MHz 80 = 80 MHz F2 = ATMC Rev. 2 Temperature Spec. M = -40 C to 150 C Figure 38. Commercial product code structure MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 115 Document revision history 7 Document revision history Table 43 summarizes revisions to this document. Table 43. Revision history Revision Date Description of Changes Rev. 1 4/2008 Initial release Rev. 2 12/2008 * Maximum amount of flash increased from 1 MB to 1.5 MB. Flash memory type has changed. Rev. 1 and later devices use LC flash instead of FL flash. * Additional packages offered--now includes100 LQFP and 176 LQFP. Please note that the pinouts can vary for the same package depending on the amount of flash memory included in the device. * Device comparison table added. * Feature details section added * Signal summary table expanded. Now includes PCR register numbers and signal selection values and pin numbers for all production packages. * Electrical characteristics updated. * DSPI timing data added for 40 MHz and 60 MHz. * Thermal characteristics data updated. Data added for 100- and 176-pin packages. * DSPI LVDS pad specifications added. Rev. 3 2/2009 Electrical characteristics updated * Flash memory electrical characteristics updated for LC flash * Power management control (PMC) and Power on Reset (POR) specifications updated * EMI characteristics data added * Maximum ratings updated * I/O pad current specifications updated * I/O Pad VRC33 current specifications added * Temperature sensor electrical characteristics added Pad type added to "Voltage" column of signal summary table Many signal names have changed to make them more understandable * DSPI: PCS_C[n] is now DSPI_C_PCS[n]; SOUT_C is now DSPI_C_SOUT, SIN_C is now DSPI_C_SIN, and SCK_C is now DSPI_C_SCK * CAN: CNTXB is now CAN_B_TX and CNRXB is now CAN_B_RC * SCI: RXDB is now SCI_B_RX and TXDB is now SCI_B_TX * In cases where multiple instances of the same IP block is incorporated into the device, e.g., 2 SCI blocks, the above nomenclature applies to all blocks "No connect" pins on pinouts clarified * Pins labelled "NIC" have no internal connection and should be tied to ground * Pins labelled "NC" are not functional pins but may be connected to internal circuits They are to be left floating Some of the longer multiplexed signal names appearing on pinouts have been moved to the inside of the package body to avoid having to use smaller fonts Orderable parts table updated Part number decoder added MPC5634M Microcontroller Data Sheet, Rev. 9 116 Freescale Semiconductor Document revision history Table 43. Revision history (continued) Revision Date Rev.4 12/2009 Description of Changes 208-pin MAPBGA ballmap for the MPC5633M (1024 KB flash memory) has changed. Power Management Control (PMC) and Power On Reset (POR) electrical specifications updated Temperature sensor data added Specifications now indicate how each controller characteristic parameter is guaranteed. I/O pad current specifications updated I/O Pad VRC33 current specifications updated PAD AC characteristics updated VGA gain specifications added to eQADC electrical characteristics DC electrical specifications updated: * Footnote added to RPUPD100K and RPUPD200K: When the pull-up and pull-down of the same nominal 200 K or 100 K value are both enabled, assuming no interference from other devices, the resulting pad voltage will be 0.5*VDDE 2.5% * IOL condition added to VOL_LS. * IOH condition added to VOH_LS. * Minimum VOH_LS is 2.3 V (was 2.7 V). * Separate IDDPLL removed from IDD spec because we can only measure IDD + IDDPLL. IDD increased by 15 mA (to 195 mA) to account for IDDPLL. IDD now documented as IDD + IDDPLL. Footnote added detailing runtime configuration used to measure IDD + IDDPLL. * Specifications for IDDSTBY and IDDSTBY150 reformatted to make more clear. * VSTBY is now specified by two ranges. The area in between those ranges is indeterminate. LVDS pad specifications updated: * Min value for VOD at SRC=0b01 is 90 mV (was 120); and 160 mV (was 180) at SRC = 0b10 Changes to Signal Properties table: * VDDE7 removed as voltage segment from Calibration bus pins. Calibration bus pins are powered by VDDE12 only. * GPIO[139] and GPIO[87] pins changed to Medium pads * Some signal names have changed on 176-pin QFP package pinout: "CAL_x" signals renamed to "ALT_x". Changes to Pad Types table: * Column heading changed from "Voltage" to "Supply Voltage" * MultiV pad high swing mode voltage changed to 3.0 V - 5.25 V (was 4.5 V - 5.25 V) * MultiV pad low swing mode voltage changed to 4.5 V - 5.25 V (was 3.0 V - 3.6 V) Signal details table added Power/ground segmentation table added 100-pin package is no longer available MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 117 Document revision history Table 43. Revision history (continued) Revision Date Rev. 5 04/2010 Description of Changes Updates to features list: * MMU is 16-entry (previously noted as 8-entry) * ECSM features include single-bit error correction reporting * eTPU2 is object code compatible with previous eTPU versions Updates to feature details: * Programming feature: eTPU2 channel flags can be tested Pinout/ballmap changes: 144 pin LQFP package: * Pin 46 is now VDDEH1B (was VDDEH4A) * Pin 61 is now VDDEH6A (was VDDEH4B) 176 pin LQFP package (1.5M devices) * Pin 55 is now VDDEH1B (was VDDEH4A) * Pin 74 is now VDDEH6A (was VDDEH4B) 176 pin LQFP package (1.5M devices) * Pin 55 is now VDDEH1B (was VDDEH4A) * Pin 74 is now VDDEH6A (was VDDEH4B) 208 ball BGA package (all devices) Ball N9 changed to VDDEH1/6 (was VDDEH6). In a future revision of the device this may be changed to NC (no connect). Changes to calibration ball names on devices with 1 MB flash memory: * CAL_MDO0 changed to ALT_MDO0 * CAL_MDO1 changed to ALT_MDO1 * CAL_MDO2 changed to ALT_MDO2 * CAL_MDO3 changed to ALT_MDO3 * CAL_MSEO0 changed to ALT_MSEO0 * CAL_MSEO1 changed to ALT_MSEO1 * CAL_EVTI changed to ALT_EVTI * CAL_EVTO changed to ALT_EVTO * CAL_MCKO changed to ALT_MCKO Power/ground segment changes: * The following pins are on VDDE7 I/O segment only on the 208-ball BGA package: ALT_MDO[0:3], ALT_MSEO[0:1], ALT_EVTI, ALT_EVTO, ALT_MCKO. * Power segments VDDEH4, VDDEH4A and VDDEH4B have been removed. CLKOUT power segment is VDDE5 (was VDDE12) Thermal characteristics for 176-pin LQFP updated (all parameter values) MPC5634M Microcontroller Data Sheet, Rev. 9 118 Freescale Semiconductor Document revision history Table 43. Revision history (continued) Revision Date Description of Changes Rev. 5 (cont.) 04/2010 PMC Operating conditions and external regulators supply voltage specifications updated * (2) PMC 5 V supply voltage VDDREG min value is 4.5 V (was 4.75 V) PMC electrical characteristics specifications updated * (1d) Bandgap reference supply voltage variation is 3000 ppm/V (was 1500 ppm/V) * (5a) Nominal 3.3 V supply internal regulator DC output voltage variation at power-on reset min value is Vdd33-8.5% (was unspecified previously) * (5a) Nominal 3.3 V supply internal regulator DC output voltage variation at power-on reset max value is Vdd3+7% (was unspecified previously) * (9a) Variation of POR for rising 5 V VDDREG supply max value is Por5V_r + 50% (was Por5V_r + 35%) * (9c) Variation of POR for falling 5 V VDDREG supply max value is Por5V_f + 50% (was Por5V_f + 35%) * (9c) note added: Minimum loading (<10 mA) for reading trim values from flash, powering internal RC oscillator, and IO consumption during POR. "Core Voltage Regulator Controller External Components Preferred Configuration" circuit diagram updated Changes to DC Electrical Specifications: * Footnote added to VDDE. VDDE must be less than VRC33 or there is additional leakage on pins supplied by VDDE. * Low range SRAM standby voltage (VSTBY) minimum changed to 0.95 V (was 0.9 V) * Low range SRAM standby voltage (VSTBY) maximum changed to 1.2 V (was 1.3 V) * High range SRAM standby voltage (VSTBY) minimum changed to 2.0 V (was 2.5 V) * VIL_LS max value (Hysteresis disabled) changed to 0.9 V (was 1.1 V) * VOH_LS min value changed to 2 V (was 2.3 V) * IDDSLOW max value is 50 mA * IDDSTOP max value is 50 mA * IDDA max value is 30 mA (was 15.0 mA) * IDD4 and VDDEH4 removed--they no longer exist I/O pad average IDDE specifications table updated I/O pad VRC33 average IDDE specifications table updated LVDS pad specifications table updated * VOS min value is 0.9 V (was 1.075 V) * VOS max value is 1.6 V (was 1.325 V) Updates to PLLMRFM electrical specifications: * Maximum values for XTAL load capacitance added. The maximum value varies with frequency. * For a 20 MHz crystal the maximum load should be 17 pF. Temperature sensor accuracy is 10 C (was 5 C) Updates to eQADC conversion specifications (operating): * Offset error without calibration max value is 160 (was 100) * Full scale gain error without calibration min value is -160 (was -120) Changes to Platform flash controller electrical characteristics: * APC, RWSC, WWSC settings vs. frequency of operation table updated MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 119 Document revision history Table 43. Revision history (continued) Revision Date Rev. 5 (cont.) 04/2010 Description of Changes Changes to flash memory specifications: * TBKPRG 64 KB specification removed (not present in this device) * T64kpperase specification added * Flash module life P/E spec for 32 Kbyte blocks also applies to 64 Kbyte blocks Pad AC specifications (3.3 V) table updated Rev. 6 04/2010 "Core Voltage Regulator Controller External Components Preferred Configuration" circuit diagram updated. * Clarification added to note: Emitter and collector capacitors (6.8 F and 10 F) should be matched (same type) and ESR should be lower than 200 mW. (Added emphasis that only 6.8 F emitter capacitors need to be matched with collector capacitor. * 220 F emitter capacitors changed to 220 nF. Rev. 7 4/2010 No specification or product information changes: * Mechanical outline drawings section renamed to "Packages" and restructured. * Rev. 8 01/2011 Removed the 208 BGA package from the device-summary table. Revised the "PMC Operating conditions and external regulators supply voltage" table. Revised the "PMC electrical characteristics" table. Revised the pad AC specifications. Revised the "DC electrical specifications" table. Revised the "DSPI LVDS pad specification" table: Revised the "PLLMRFM electrical specifications" table. Change to "Temperature sensor electrical characteristics" table: * Accuracy is guaranteed by production test Revised the "eQADC conversion specifications (operating)" table. Changes to "Calibration bus operation timing" table: * CLKOUT period is guaranteed by production test. All other parameters are guaranteed by design Changes to "Program and erase specifications" table in "Flash memory electrical characteristics" section. * Deleted Bank Program (512KB) (TBKPRG) parameter * TYP P/E values added for 32- and 64 KB blocks and for 128 KB blocks. Changes to Recommended operating characteristics for external power transistor: * VCESAT should be between 200 and 600 mV * VBE should be 0.4V to 1.0V Removed footnote 8 from Vddeh in Maximum ratings. Deleted engineering names for pads in Power UP/DOWN Sequencing Section Changed "sin_c" to DSPI_C_SIN" and "sck_c" to DSPI_C_SCK" on 144 pin LQFP package. Updated the "Electromagnetic Interference Characteristics" table to reflect new parameter levels, test conditions. In the "APC, RWSC, WWSC settings vs. frequency of operation" table, changed 82 MHz entry for WWC from "11" to "01", added an extra row for "All 111 111 11" MPC5634M Microcontroller Data Sheet, Rev. 9 120 Freescale Semiconductor Document revision history Table 43. Revision history (continued) Revision Date Description of Changes Rev 9 05/2012 In Section 4.6.1, "Regulator example * Updated ,Figure 7 "Core voltage regulator controller external components preferred configuration" to show RC, RB, RE, CC, CB, CE, CD and CREG. * Added Table 15 "Required external PMC component values", Table 16 "Network 1 component values", Table 17 "Network 2 component values" and Table 18 "Network 3 component values". Updated Table 1: Number of eMIOS channels changed from `8' to `16' for MPC5632M. In Section 4.2, "Maximum ratings, Table 7 * VFLASH maximum value changed from 3.6V to 5.5V and changed table note3 to: "The VFLASH supply is connected to VDDEH" * Removed table note 4, "Allowed 5.3 V for 10 hours cumulative time, remaining time at 3.3 V +10%" In Section 4.12, "eQADC electrical characteristics: * Added note. * In Table 29, additional five parameters added (SNR, THD, SFDR, SINAD and ENOB) and added footnotes # 9,10 and 11. MPC5634M Microcontroller Data Sheet, Rev. 9 Freescale Semiconductor 121 Document revision history How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Home Page: www.freescale.com Web Support: http://www.freescale.com/support Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics as their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. Asia/Pacific: Freescale Semiconductor China Ltd. Exchange Building 23F No. 118 Jianguo Road Chaoyang District Beijing 100022 China +86 10 5879 8000 support.asia@freescale.com For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. For Literature Requests Only: Freescale Semiconductor Literature Distribution Center 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org (c) Freescale Semiconductor, Inc. 2008-2012. All rights reserved. Document Number: MPC5634M Rev. 9 05/2012 MPC5634M Microcontroller Data Sheet, Rev. 9 122 Freescale Semiconductor