SERIES 107 ALUMINUM INSERTER - EXTRACTOR Calmark offers the Series 107 Aluminum Inserter-Extractor for safe and easy insertion and extraction of printed circuit boards in the most severe applications. This product series offer a wide range of inserter-extractor with varying features from mechanical advantage ratios, color, board thickness, etc. If you don't see one here that meets your requirements, please contact our Applications Engineers with your specification. FEATURES n "Ultra strong" lever action design overcomes insertion and extraction forces of highest possible limits n Widths from 7.37 (.290) to 7.92 (.312) for printed circuit boards ranging from 1.6 (.063) to 3.2 (.125) thick n Actuates from a simple "U" channel form n Mounting detail on card retrofits other industry standards n Available in black anodize or clear chemical film n Generous area for identification markings n Strong and Ultra-strong lever action overcome high insertion and extraction forces n 107-73 and 107-75 offers a positive locking feature MATERIALS/FINISH EXTRACTOR Aluminum alloy 6061-T6. Black anodize per Mil-A-8625, Type II Cl. 2. or Clear chemical film per Mil-5541 Cl 3 for a conductive finish. Other anodize colors or a gold chemical film also available. Please contact an Application Engineer with your requirements. ROLL PIN Stainless steel, 2.38 (.094) x 6.35 (.250) [except all Series 107-35 use 7.95 (.313) long]. Roll pins are furnished with each inserterextractor. [Series 107-73 and 107-75, two roll pins] Series 107-50 - Inserter/Extractor (Aluminum) Series Feature Board Thickness Standard Color Mechanical Advantage Figures 107-35 C107-35 107-35-3 C107-35-3 107-35-4 C107-35-4 107-50 C107-50 107-50-3 C107-50-3 107-50-4 C107-50-4 107-51 C107-51 107-51-3 C107-51-3 107-51-4 C107-51-4 107-55 C107-55 107-55-3 C107-55-3 107-55-4 C107-55-4 107-73 C107-73 107-73-3 C107-73-3 107-73-4 C107-73-4 107-75 C107-75 107-75-3 C107-75-3 107-75-4 C107-75-4 I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I 1.6 1.6 2.4 2.4 3.2 3.2 1.6 1.6 2.4 2.4 3.2 3.2 1.6 1.6 2.4 2.4 3.2 3.2 1.6 1.6 2.4 2.4 3.2 3.2 1.6 1.6 2.4 2.4 3.2 3.2 1.6 1.6 2.4 2.4 3.2 3.2 black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear black clear 5.5:1 5.5:1 5.5:1 5.5:1 5.5:1 5.5:1 4.5:1 4.5:1 4.5:1 4.5:1 4.5:1 4.5:1 3.3:1 3.3:1 3.3:1 3.3:1 3.3:1 3.3:1 8:1 8:1 8:1 8:1 8:1 8:1 4.2:1 4.2:1 4.2:1 4.2:1 4.2:1 4.2:1 7:1 7:1 7:1 7:1 7:1 7:1 1/A 1/A 1/A 1/A 1/A 1/A 2/B 2/B 2/B 2/B 2/B 2/B 3/B 3/B 3/B 3/B 3/B 3/B 4/B 4/B 4/B 4/B 4/B 4/B 5/C 5/C 5/C 5/C 5/C 5/C 6/C 6/C 6/C 6/C 6/C 6/C E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E L L L L L L L L L L L L (.063) (.063) (.093) (.093) (.125) (.125) (.063) (.063) (.093) (.093) (.125) (.125) (.063) (.063) (.093) (.093) (.125) (.125) (.063) (.063) (.093) (.093) (.125) (.125) (.063) (.063) (.093) (.093) (.125) (.125) (.063) (.063) (.093) (.093) (.125) (.125) Feature: I = Inserter E = Extractor L = Latching For Pre-start pin feature, add "P" prefix to part number 66 www.calmark.com * 800-854-7086 SERIES 107 ALUMINUM INSERTER - EXTRACTOR 11.18 (.440) 9.91 (.390) 12.7 (5.00) 3.96 (.156) R 50.8 (2.00) 43.2 (1.70) 3.96 (.156) R 12.7 (5.00) 38.1 (1.50) 3.96 (.156) R 8.26 (.325) 12.06 (.475) 12.06 (.475) 7.92 (.312) FIG. 1 FIG. 2 12.7 (5.00) 7.37 (.290) FIG. 3 7.37 (.290) 22.4 (.88) 22.4 (.88) 47.5 (1.87) 50.8 (2.00) 12.06 (.475) 12.7 (5.00) 88.9 (3.50) 82.5 (3.25) FIG. 5 12.06 (.475) 12.06 (.475) Units: mm (in) Unless specified otherwise, .xx = .25, .x = .5 (.xxx = .010, .xx = .02) 7.37 (.290) FIG. 4 7.37 (.290) 12.7 (5.00) 7.37 (.290) FIG. 6 Provides insertion and extraction travel of 7.6 (.30) min. Nominal position of card edge when seated in connector. The InserterExtractor will allow .76 (.03) overtravel for tolerance take-up. 1.02 (.040) Ref APPLICATION DATA Card Guide Surface 4.83 .25 (.109 .010) 17.8 (.70) 7.87 (.310) 9.4 (.37) 4.57 (.180) 2.36 (.093) Dia. .8 (.03) max. 4.3 (.17) min. Detail of Actuating Surfaces Required on Top and Bottom Guide Plates Units: mm (in) Unless specified otherwise, .xx = .25, .x = .5 (.xxx = .010, .xx = .02) FIG. A Provides insertion and extraction travel of 8.9 (.35) min. Nominal position of card edge when seated in connector. The InserterExtractor will allow 1.3 (.05) overtravel for tolerance take-up. 7.24 .38 (.285 .015) Two inserter or inserter-extractors are recommended per printed circuit board taller than 127 (5) in height. Provides insertion and extraction travel of 8.9 (.35) min. Nominal position of card edge when seated in connector. The InserterExtractor will allow 1.3 (.05) overtravel for tolerance take-up. 2.77 (.109) Dia. 6.35 (.250) 1.5 (.06) Card Guide Surface 9.1 (.36) 18.5 (.73) 7.24 .38 (.285 .015) 1.5 (.06) max. 6.1 (.24) min. Detail of Actuating Surfaces Required on Top and Bottom Guide Plates FIG. B 6.35 (.250) 2.38 (.94) Dia. 22.86 .13 (.900 .005) 2.29 .13 (.090 .005) 6.35 (.250) 1.5 (.06) Card Guide Surface 1.5 (.06) max. 6.1 (.24) min. Detail of Actuating Surfaces Required on Top and Bottom Guide Plates 18.5 (.73) 9.1 (.36) 6.35 (.250) 2.77 (.109) Dia. FIG. C www.calmark.com * 800-854-7086 67