LP55271TLX/NOPB - Texas Instruments

LP55271

VDD1 VDD2

CVDD1 CVDD2

100 nF

3.0 to 5.5V CIN

10 PF

4.7 PH

COUT2

10 PF

CVREF

100 nF

SW2

LED1

LED2

LED3

LED4

FLASH

VREF

GNDs

47 nF

ASE1

VIN

VOUT

COUT1

10 PF

CVDDA

4.7 PF

VDDA

SW1

ASE2

CAMERA FLASH_SYNC

2TEST

INTERFACE

AUDIO

SIGNAL

AUDIO

SIGNAL

MCU SCL

NRST

VDD_IO

CVDD_IO

100 nF

SDA RF

IFLASH 1.3 k:

82 k:

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Tiny LED Driver for Camera Flash and Four LEDs With I

C Programmability, Connectivity

Test, and Audio Synchronization

Check for Samples: LP55271

1FEATURES APPLICATIONS

2• High Current Boost DC-DC Converter • Camera Flash, Funlight, and Backlight Driving

(up to 1-A Output Current) in Battery-Powered Devices

• Programmable Boost Output Voltage DESCRIPTION

• 370-mA Flash LED Constant-Current Driver The LP55271 is a lighting management unit for

With Low Tolerance and a Safety Circuit handheld devices with I2C compatible control

• Synchronization Pin for Flash Timing interface. The LP55271 has a step-up DC/DC

• Two Single-Ended Audio Inputs With Gain converter with high current output and it drives

display and keypad backlights and powers the

Control camera flash LED. In addition the DC/DC converter

• Four Constant-Current 15-mA LED Drivers has the output current to power for example an audio

With 8-Bit Programmable Brightness Control amplifier simultaneously. The chip has four 8-bit

• Audio Synchronization Feature programmable high efficiency constant current LED

drivers and a FLASH LED driver. Built-in audio

• I2C Compatible Control Interface synchronization feature allows the user to

• Built-in LED Connectivity Test to Maximize synchronize one of the LEDs to audio input.

Manufacturing Yield

• Small DSBGA-30 Package (2.5 mm x 3.0 mm x

0.6 mm)

Typical Application

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2All trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

VDD2VDDAVREF

GNDA

VDDIO

GND_

FLASH

GNDC

RT ASE2

ASE1

SDA

FLASH IFLASH

FLASH_

SYNC VDD1 GND SCL NRST

LED4LED3

LED2LED1

T1T2

GND_

SW1

SW1 SW2 FB GND_

LED

GND_

SW2

VDD2 VDDA VREF GNDA VDDIO GND_

FLASH

IFLASH ASE2 ASE1 RT SDA FLASH

NRST SCL GND VDD1 FLASH_

SYNC GNDC

LED4 LED3 T1 T2 GND_

SW2 GND_

SW1

LED2 LED1 GND_

LED FB SW2 SW1

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

DESCRIPTION (CONTINUED)

The LP55271 has an integrated 370 mA flash driver with a safety stop feature and 46 mA torch mode. An

external enable pin is provided for the synchronizing the flash with the camera action. An external software

independent test interface provides a fast way to find a broken path or short on LED circuits. Very small DSBGA

package together with minimum number of external components is a best fit for handheld devices.

CONNECTION DIAGRAMS

DSBGA-30 package, 2.466 x 2.974 x 0.60 mm body size, 0.5 mm pitch, Package Number YZR0030

Figure 1. Top View Figure 2. Bottom View

Table 1. Pin Descriptions

Pin Name Type(1) Description

D3 VDD1 P Supply Voltage

A1 VDD2 P Supply Voltage

F5 SW1 A Boost Converter Switch

E5 SW2 A Boost Converter Switch

D5 FB A Boost Converter Feedback

B5 LED1 O LED1 Driver Output

A5 LED2 O LED2 Driver Output

B4 LED3 O LED3 Driver Output

A4 LED4 O LED4 Driver Output

F2 FLASH O Flash LED Driver Output

F3 GNDC G Ground for Core Circuitry

D2 RT A Oscillator Frequency Setting

C1 VREF A Reference Voltage

B1 VDDA P Internal LDO

F4 GND_SW1 G Boost Converter Ground

E4 GND_SW2 G Boost Converter Ground

C5 GND_LED G LEDs 1 to 4 Driver Ground Connection

F1 GND_FLASH G Flash Driver Ground Connection

(1) A: Analog Pin D: Digital Pin G: Ground Pin P: Power Pin, I: Input Pin I/O: Input/Output Pin O: Output Pin OD: Open Drain Pin

Product Folder Links: LP55271

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Table 1. Pin Descriptions (continued)

Pin Name Type(1) Description

A2 IFLASH A Resistor for Flash Current Setting

D1 GNDA G Analog Ground Connection

C3 GND G Ground

E1 VDD_IO P Supply Voltage for Digital Interface

A3 NRST DI Low Active Reset

B3 SCL DI I2C Compatible Interface Clock Signal

E2 SDA OD I2C Compatible Interface Data Signal

E3 FLASH_SYNC DI FLASH LED Control

D4 T2 DO Test Pin (Result)

C4 T1 DI Test Pin (Clock)

C2 ASE1 AI Audio Input

B2 ASE2 AI Audio Input

Product Folder Links: LP55271

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Absolute Maximum Ratings (1) (2)(3)

Voltage on power pins (VDD1,2) -0.3V to +6.0V

Voltage on analog pins -0.3V to VDD1,2+0.3V with 6.0V max

Voltage on input/output pins -0.3V to VDD1,2+0.3V with 6.0V max

V(all other pins): Voltage to GND -0.3V to 6.0V

I(VREF) 10 µA

I(FLASH) 500 mA

Continuous Power Dissipation (4) Internally Limited

Junction Temperature (TJ-MAX) 125ºC

Storage Temperature Range -65ºC to +150ºC

Maximum Lead Temperature (Reflow soldering, 3 times)(5) 260ºC

ESD Rating, Human Body Model(6) 2 kV

(1) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under

which operation of the device is specified. Operating Ratings do not imply performance limits. For performance limits and associated test

conditions, see the Electrical Characteristics tables.

(2) All voltages are with respect to the potential at the GND pins.

(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.

(4) Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ= 160ºC (typ.) and

disengages at TJ= 140ºC (typ.).

(5) For detailed soldering specifications and information, see application note AN1112 : DSBGA Wafer Level Chip Scale Package.

(6) The Human body model is a 100 pF capacitor discharged through a 1.5 kΩresistor into each pin. MIL-STD-883 3015.7

Operating Ratings (1),(2)

Voltage on power pins (VDD1,2) 3.0 to 5.5V

Voltage on ASE1, ASE2 0V to 1.6V

VDD_IO 1.65V to VDD1

Junction Temperature (TJ) Range -30ºC to +125ºC

Ambient Temperature (TA) Range (3) -30ºC to +85ºC

(1) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under

which operation of the device is specified. Operating Ratings do not imply performance limits. For performance limits and associated test

conditions, see the Electrical Characteristics tables.

(2) All voltages are with respect to the potential at the GND pins.

(3) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may

have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =

125ºC), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the

part/package in the application (θJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (θJA × PD-MAX).

Thermal Properties

Junction-to-Ambient Thermal Resistance (θJA)(1) 60 - 100ºC/W

(1) Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high maximum power

dissipation exists, special care must be paid to thermal dissipation issues in board design.

Product Folder Links: LP55271

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Electrical Characteristics(1) (2)

Limits in standard typeface are for TJ= 25ºC. Limits in boldface type apply over the operating ambient temperature range (-

30ºC < TA< +85ºC). Unless otherwise noted, specifications apply to the LP55271 Block Diagram with: VIN = 3.6V, CIN = 10

µF, COUT1 = 10 µF, COUT2 = 10 µF, CVDD_IO = 100 nF, CVREF = 100 nF, CVDDA = 4.7 µF, CVDD1 = 100 nF, CVDD2 = 100 nF, L1=

4.7 µH. (3)

Symbol Parameter Test Conditions Min Typ Max Unit

Current of VDD1 + VDD2 pins + 1 5µA

Voltage on VDD_IO = 0V, NRST = L,

ISHUT DOWN Leakage Current of SW1, SW2, NSTBY(bit) = L

LED1 to 4 and FLASH NRST = H, NSTBY(bit) = H, no 350 µA

Active Mode Supply Current

IDD load, EN_BOOST(bit) = L, SCL,

(VDD1 + VDD2 current) SDA = H

NSTBY(bit) = H, EN_BOOST(bit) = 850 µA

No load supply current

IDD H, SCL, SDA, NRST = H,

(VDD1 + VDD2 current) AUTOLOAD_EN(bit) = L

IVDDIO VDD_IO Standby Supply current NSTBY(bit) = L 1µA

VDDA IVDDA = 1 mA -4% 2,8V +4% V

(1) All voltages are with respect to the potential at the GND pins.

(2) Min and Max limits are specified by design, test, or statistical analysis. Typical numbers represent the most likely norm.

(3) Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.

Product Folder Links: LP55271

VIN

MICRO-

CONTROLLER

NRST

FLASH_SYNC

CVDD_IO

100 nF

CIN

10 ?F

VDD_IO

VDD1

SW1

LED1

FLASH

CVREF

100 nF

VDDA

GNDSW1

GND_FLASH

FLASH

CONTROL

LIGHTING

CONTROL

INTERNAL LDO

2.8V

370 mA

FLASH

4.7 ?F

CVDDA

SERIAL

INTERFACE

SCL

SDA

REGISTERS

FINITE STATE

MACHINE

EPROM POR

VREF

VIN

THERMAL

SHUTDOWN

GNDA

CAMERA

CVDD1

100 nF

VDD2

CVDD2

100 nF

INTERNAL

OSC

LED CONNECTIVITY TEST

4.7 ?HL1

GND_LED

LED2

LED3

LED4

KEYPAD

AND

BACKLIGHT

0 TO 15 mA

/LED

FUNLIGHT

OUTPUT

SELECTOR

LIGHTING

CONTROL

LEVEL

DETEC.

GAIN

CONTROL

AND ADC

47 nF

GNDSW2

PWM

ERROR

AMP

RT82 k?

10 ?F

COUT1 COUT2

10 ?F

SW2

DAC

GNDC

TIME

LIMIT

GND

RF1300?

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

LP55271 BLOCK DIAGRAM

Product Folder Links: LP55271

STANDBY

RESET

BOOST STARTUP

NORMAL MODE

POR = H

or = NRST L

and

NRST=H

INTERNAL

STARTUP

SEQUENCE

and

NRST=H

~10 ms DELAY

1) TSD =L

TSD=H VREF = 95%OK1

EN_BOOST(bit)=H1

NSTBY(bit) = H

and

NRST=H

NSTBY(bit)=L

NRST=H

NSTBY(bit)=H

and NSTBY(bit)=L

EN_BOOST(bit)=H1

EN_BOOST(bit)=L1

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

DEVICE INFORMATION

Modes of Operation

RESET: In the reset mode all the internal registers are reset to the default values. Reset is entered always if

input NRST is LOW or internal Power On Reset (POR) is active. Power on reset will activate during the

chip startup or when the supply voltage VDD2 falls below 1.5V. Once VDD2 rises above 1.5V, POR will

inactivate and the chip will continue to the STANDBY mode. NSTBY control bit is low after POR by

default.

STANDBY: The standby mode is entered if the register bit NSTBY is LOW and reset is not active. This is the

low power consumption mode, when all circuit functions are disabled. Registers can be written in this

mode and the control bits are effective immediately after start up.

STARTUP: When NSTBY bit is written high, the internal startup sequence powers up all the needed internal

blocks (VREF, Oscillator, etc.). To ensure the correct oscillator initialization, a 10 ms delay is generated by

the internal state-machine. If the chip temperature rises too high, the thermal shutdown (TSD) disables the

chip operation and startup mode is entered until no thermal shutdown event is present.

BOOST STARTUP:Soft-start for boost output is generated in the boost startup mode. The boost output is raised

in a low current PWM mode during the 10 ms delay generated by the state-machine. The boost startup is

entered from internal startup sequence if EN_BOOST is HIGH or from normal mode when EN_BOOST is

written HIGH.

NORMAL: During normal mode the user controls the chip using the Control Registers. The registers can be

written in any sequence and any number of bits can be altered in a register in one write.

Product Folder Links: LP55271

VOUT

VIN

Duty control2 MHz clock

OVPCOMP

ERRORAMP

SLOPER

RESETCOMP

LOOPC

ACTIVE

LOAD

SWITCH

UVCOMP

IMAX

OCPCOMP

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Magnetic Boost DC/DC Converter

The LP55271 boost DC/DC converter generates a 4.00 – 5.40V output voltage to drive the LEDs from a single

Li-Ion battery (3.0V to 4.5V). The output voltage is controlled with a 4-bit register in 8 steps. The converter is a

magnetic switching PWM mode DC/DC converter with a current limit. The converter has 2.0 MHz / 1.0 MHz

selectable switching frequency operation, when the timing resistor RT is 82 kΩ.

The LP55271 boost converter uses pulse-skipping elimination method to stabilize the noise spectrum. Even with

light load or no load a minimum length current pulse is fed to the inductor. An internal active load is used to

remove the excess charge from the output capacitor when needed.

The topology of the magnetic boost converter is called CPM control, current programmed mode, where the

inductor current is measured and controlled with the feedback. The output voltage control changes the resistor

divider in the feedback loop.

Figure 3 shows the boost topology with the protection circuitry. Four different protection schemes are

implemented:

1. Over voltage protection, limits the maximum output voltage.

– Keeps the output below breakdown voltage.

– Prevents boost operation if battery voltage is much higher than desired output.

2. Over current protection, limits the maximum inductor current.

– Voltage over switching NMOS is monitored; too high voltages turn the switch off.

3. Feedback (FB) protection for no connection.

4. Duty cycle limiting, done with digital control.

Figure 3. Boost Converter Topology

Product Folder Links: LP55271

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

MAGNETIC BOOST DC/DC CONVERTER ELECTRICAL CHARACTERISTICS

Limits in standard typeface are for TJ= 25ºC. Limits in boldface type apply over the operating ambient temperature range (-

30ºC < TA< +85ºC). Unless otherwise noted, specifications apply to the LP55271 Block Diagram with: VIN = 3.6V, CIN = 10

µF, COUT1 = 10 µF, COUT2 = 10 µF, CVDDIO = 100 nF, CVREF = 100 nF, CVDDA = 4.7 µF, CVDD1 = 100 nF, CVDD2 = 100 nF, L1=

4.7 µH. (4)

Symbol Parameter Test Conditions Min Typ Max Unit

3.2V ≤VIN ≤4.5V

ILOAD Load Current(1) 670 mA

VOUT = 5.0V

3.2V ≤VIN ≤4.5V

Output Voltage Accuracy (FB pin) VOUT (target value) = 5.0V, −5 +5 %

active load off

VOUT 3.0V ≤VIN ≤(5.0V+VSCHOTTKY)5.0 V

active load off

Output Voltage (FB Pin) VIN -

VIN > (5.0V + VSCHOTTKY)VSCHOTTKY

RDSON Switch ON Resistance VIN = 3.6V, ISW = 1.0A 0.20 0.4 Ω

RT = 82 kΩ2.0

PWM Mode Switching Frequency FREQ_SEL (bit) = 1 MHz

1.0

FREQ_SEL (bit) = 0

fPWF 3.2V ≤VDD1,2 ≤5.0V −6 +6

Frequency Accuracy ±3 %

RT = 82 kΩ-9 +9

tPULSE Switch Pulse Minimum Width no load 25 ns

tSTARTUP Startup Time 10 ms

ICL_OUT SW1 + SW2 current limit 1.7 A

(4) Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.

(1) Specified currents are the worst case currents. If input voltage is larger or output voltage is smaller, current can be increased according

to graph "Boost Maximum Output Current".

BOOST STANDBY MODE

User can set the boost converter to STANDBY mode by writing the register bit EN_BOOST low when there is no

load to avoid idle current consumption. When EN_BOOST is written high, the converter starts in low current

PWM (Pulse Width Modulation) mode for 10 ms and then goes to normal PWM mode.

BOOST CONTROL REGISTERS

User can control the boost output voltage and the switching frequency according to the following tables.

Boost Output Voltage Boost Output Voltage (V)

[3:0] Register (Typical)

0000 4.00

0001 4.20

0011 4.40

0111 4.60 default

1000 4.80

1001 5.00

1011 5.20

1111 5.40

Boost Switching Frequency

FREQ_SEL Bit (Typical)

0 1.0 MHz default

1 2.0 MHz

Product Folder Links: LP55271

ILOAD = 670 mA

VOUT = 5.4V

VOUT = 4.0V

FREQ_SEL (bit) =1

FREQ_SEL (bit) =0

L = TDK VLCF5020T-4R7N1R7-1

ILOAD = 100 mA

300 mA

500 mA

670 mA

fBOOST = 2.0 MHz

VSWITCH

(5V/DIV)

ICOIL=150 mA

AVERAGE

(100mA/DIV) VOUT

(10 mV/DIV)

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Boost Converter Typical Performance Characteristics

TJ= 25ºC. Unless otherwise noted, typical performance characteristics apply to the LP55271 Block Diagram with:

VIN = 3.6V, VOUT = 5.0V, CIN = 10 µF, COUT1 = 10 µF, COUT2 = 10 µF, CVDD_IO = 100 nF, CVREF = 100 nF, CVDDA =

4.7 µF, CVDD1 = 100 nF, CVDD2 = 100 nF, L1 = 4.7 µH (1).

Boost Converter Efficiency Boost Typical Waveforms at 100 mA Load

Figure 4. Figure 5.

Battery Current vs Voltage Boost Frequency vs RT Resistor

Figure 6. Figure 7.

(1) Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.

Product Folder Links: LP55271

VOUT = 5V

(50 mV/DIV) ILOAD

(20 mA/DIV)

VOUT = 5.4V

VOUT = 4.0V

fBOOST = 2.0 MHz

VIN (500 mV/DIV)

VIN (3.0V TO 3.6V)

VOUT = 5V (10 mV/DIV)

ILOAD = 50 mA

EN_AUTOLOAD (bit) = 1

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Boost Line Regulation 3.0V - 3.6V Boost Startup to 5.4V with no Load

Figure 8. Figure 9.

Boost Load Transient Response, 50 mA to 100 mA Boost Maximum Output Current

Figure 10. Figure 11.

Product Folder Links: LP55271

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Flash Driver

LP55271 has an internal constant current driver that is capable for sinking low (46 mA) and high (370 mA)

current mainly targeted for torch and flash LED in camera phone applications. 370 mA flash driver can be

hardware or software enabled. Flash safety function prevents hardware damages due to possible overheating

when the flash has been stuck on because of a hardware, software or user error.

Flash safety counter starts counting when the flash is activated and disables the flash automatically when the

pre-defined 1.0s or 2.0s time limit is reached. Flash is activated with FLASH_SYNC bit or FLASH_SYNC pin, as

defined in the table below. Safety time limit is defined by SAFETY_TIME bit. (Time limit is 2.0s if SAFETY_TIME

bit is low and 1.0s if the bit is high.)

Flash driver currents — both torch and flash — are set with external resistor R F. The flash current is 480/RF

amperes and the torch current is 60/RFamperes. User should not use lower resistance value than 1200Ω.

Table 2. Flash LED Control(1)

EN_TORCH bit EN_FLASH bit FLASH_SYNC bit or pin SAFETY_TIME bit Flash LED Action

0 0 X X Off

1 0 X X Torch

X 1 Change from LOW to HIGH to 0 for 2.0 seconds; Flash

engage; from HIGH to LOW to 1 for 1.0 second

disengage

(1) X = don’t care

Table 3. Flash Programming Example

Address Data Function

00H 8FH Sets safety time to 1.0s. In this example LED1 to LED4 are enabled.

00H 9FH Enables torch.

Activates FLASH. EN_FLASH bit and FLASH_SYNC bit are written simultaneously because EN_FLASH

00H FFH disables torch.

Disables FLASH. If FLASH is disabled by safety time, FLASH_SYNC bit needs to be written to 0 before next

00H BFH FLASH.

FLASH DRIVER ELECTRICAL CHARACTERISTICS

Limits in standard typeface are for TJ= 25ºC. Limits in boldface type apply over the operating ambient

temperature range (-30ºC < TA< +85 ºC). Unless otherwise noted, specifications apply to the LP55271 Block

Diagram with: VIN = 3.6V, CIN = 10 µF, COUT1 = 10 µF, COUT2 = 10 µF, CVDDIO = 100 nF, CVREF = 100 nF, CVDDA =

4.7 µF, CVDD1 = 100 nF, CVDD2 = 100 nF, L1= 4.7 µH, RF= 1300Ω

Symbol Parameter Test Conditions Min Typ Max Unit

370 mA

3.0V ≤VIN ≤5.5V,

IFLASH Flash Mode Sink Current(1) VFLASH = 1.0V -7.5 +7.5 %

ITORCH Torch Mode Sink Current(1) 3.0V ≤VIN ≤5.5V 46 mA

ILEAKAGE Flash Driver Leakage Current VFB = 5.0V 0.1 µA

tFLASH Flash Turn-On Time (2) 20 µs

3.0V ≤VIN ≤5.5V,

VSAT Saturation Voltage Current Decreased to 95% of the 550 mV

Maximum Sink Current

tSAFETY Safety Time Accuracy -9 +9 %

(1) Min and Max limits are specified by design, test, or statistical analysis. Typical numbers represent the most likely norm.

(2) Flash turn-on time is measured from the moment the flash is activated until the flash current crosses 90% of its target value.

Constant Current Sink Outputs LED1, LED2, LED3, LED4

LP55271 has four independent backlight/keypad LED drivers. All the drivers are regulated constant current sinks.

LED currents are controlled by 8-bit current mode DACs. Every driver can be controlled in two ways:

1. Brightness control with constant current drivers

Product Folder Links: LP55271

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

2. Direct ON/OFF control. The current is pre-set by 8-bit current mode DAC.

In addition, LED1 driver can be synchronized to audio input signal amplitude.

By using brightness control user can set brightness of every single LED by using 8-bit brightness control

registers. If analog audio is available on system the user can use audio synchronization for synchronizing LED1

to the music. Direct ON/OFF control is mainly for switching LEDs on and off.

LED Control Register (00 hex) has control bits for direct on/off control of all the LEDs. Note that the LEDs have

to be turned on in order to control them with audio synchronization (LED1 only) or brightness control.

The brightness is programmed as described in the following.

ILED = n x (15 mA / 255)

where

• n = LED[7:0] (8-bit)

• step = 15 mA / 255 ≈0.05882 mA (1)

For example if 13.2 mA is required for driver current:

n = 13.2 mA / (15 mA / 255) ≈224

224 = 1110 0000, E0 hex

Table 4. LED1 to LED4 Brightness Control

LED1[7:0], LED2[7:0], LED3[7:0] and Driver Current, mA

LED4[7:0] Registers (typical)

0000 0000 0

0000 0001 0.059

0000 0010 0.118

• •

1110 0000 13.176

• •

1111 1110 14.941

1111 1111 15

LED1 TO LED4 DRIVERS ELECTRICAL CHARACTERISTICS

Limits in standard typeface are for TJ= 25ºC. Limits in boldface type apply over the operating ambient

temperature range (-30ºC < TA< +85ºC). Unless otherwise noted, specifications apply to the LP55271 Block

Diagram with: VIN = 3.6V, CIN = 10 µF, COUT1 = 10 µF, COUT2 = 10 µF, CVDDIO = 100 nF, CVREF = 100 nF, CVDDA =

4.7 µF, CVDD1 = 100 nF, CVDD2 = 100 nF, L1= 4.7 µH. (1)

Symbol Parameter Test Conditions Min Typ Max Unit

IMAX Maximum Sink Current 15 mA

ILEAKAGE Leakage Current VFB = 5.0V 0.03 µA

13.2 mA

ILED Current Tolerance ISINK = 13.2 mA (target value) -7 +7 %

Sink Current Matching Between

IMATCH ISINK = 13.2 mA 1 %

LED 1 to 4(1)

3.0V ≤VIN ≤5.5V,

VSAT Saturation Voltage Current Decreased to 95% of the 150 230 mV

Maximum Sink Current

(1) Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.

(1) Sink current matching is the maximum difference from the average.

Product Folder Links: LP55271

15k

ASE1

15k

ASE2 ADC

Threshold

AGC

GAIN_SEL

[2:0]

AGC

PEAK

DETECTOR

LED

CONTROL

HOLD

SPEED_CTRL[1:0]

THRESHOLD

[3:0]

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Audio Synchronization

The LED1 output can be synchronized to incoming audio signal with Audio Synchronization feature. Audio

Synchronization synchronizes LED1 based on input signal’s peak amplitude. Programmable gain and automatic

gain control function are also available for adjustment of input signal amplitude to light response. Control of LED1

brightness refreshing frequency is done with four different frequency configurations. The digitized input signal has

a DC component that is removed by a digital DC-remover. The DC-remover is a high-pass filter where corner

frequency is user selectable by using DC_FREQ bit. LP55271 has 2-channel audio (stereo) input for audio

synchronization, as shown in Figure 12. The inputs accept signals in the range of 0V to 1.6V peak-to-peak and

these signals are mixed into a single wave so that they can be filtered simultaneously.

LP55271 audio synchronization is mainly done digitally and it consists following signal path blocks (see

Figure 12).

• Input buffer

• AD converter

• Automatic Gain Control (AGC) and manually programmable gain

• Peak detector

Automatic Gain Control (AGC) adjusts the input signal to suitable range automatically. User can disable AGC

and the gain can be set manually with programmable gain. Audio synchronization is based on peak detection

method.

Figure 12.

Audio Synchronization Input Electrical Parameters

Symbol Parameter Test Conditions Min Typ Max Unit

ZIN Input Impedance of ASE1, ASE2 10 15 kΩ

ASE1, ASE2 Audio Input Level Min input level needs maximum gain;

AIN 0 1600 mV

Range (peak-to-peak) Max input level for minimum gain.

CONTROL OF AUDIO SYNCHRONIZATION

The following table describes the controls required for audio synchronization. LED1 brightness control through

serial interface is not available when audio synchronization is enabled.

Table 5. Audio Synchronization Control

EN_SYNC Audio synchronization enabled. Set EN_SYNC = 1 to enable audio synchronization or 0 to disable.

EN_AGC Automatic gain control. Set EN_AGC = 1 to enable automatic control or 0 to disable.

When EN_AGC is disabled, the audio input signal gain value is defined by GAIN_SEL.

GAIN_SEL[2:0] Input signal gain control. Gain has a range from 0 dB to -46 dB.

SPEED_CTRL[1:0] Control for refreshing frequency. Sets the typical refreshing rate for the LED1 output.

THRESHOLD[3:0] Control for the audio input threshold. Sets the typical threshold for the audio inputs signals.

May be needed if there is noise on the audio lines.

DC_FREQ Control for the high-pass filter corner frequency.

0 = 80 Hz

1 = 510 Hz

Product Folder Links: LP55271

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Table 6. Audio Input Threshold Setting

Threshold[3:0] Threshold Level, mV (typical)

0000 Disabled

0001 0.2

0010 0.4

* *

1110 2.5

1111 2.7

Table 7. Typical Gain Values vs. Audio Input Amplitude

Audio Input Amplitude mVP-P Gain Value dB

0 to 10 0

0 to 20 -6

0 to 40 -12

1 to 85 -18

3 to 170 -24

5 to 400 -31

10 to 800 -37

20 to 1600 -46

Table 8. Input Signal Gain Control

GAIN_SEL[2:0] Gain dB

000 0

001 -6

010 -12

011 -18

100 -24

101 -31

110 -37

111 -46

Table 9. Refreshing Frequency

SPEED_CTRL[1:0] Refreshing Rate Hz

00 FASTEST

01 15

10 7.6

11 3.8

Product Folder Links: LP55271

SCL

SDA

data

change

allowed

data

valid

data

change

allowed

data

valid

data

change

allowed

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Logic Interface Characteristics

Limits in standard typeface are for TJ= 25ºC. Limits in boldface type apply over the operating ambient temperature range (-

30ºC < TA< +85ºC). Unless otherwise noted, specifications apply to the LP55271 Block Diagram with: VIN = 3.6V, CIN = 10

µF, COUT1 = 10 µF, COUT2 = 10 µF, CVDDIO = 100 nF, CVREF = 100 nF, CVDDA = 4.7 µF, CVDD1 = 100 nF, CVDD2 = 100 nF, L1=

4.7 µH (1)

Symbol Parameter Test Conditions Min Typ Max Unit

Logic Inputs SCL and FLASH_SYNC

0.2 x

VIL Input Low Level V

VDD_IO

0.8 x

VIH Input High Level V

VDD_IO = 1.65V to VDD1,2 VDD_IO

IIInput Current -1.0 1.0 µA

fSCL SCL Pin Clock Frequency 400 kHz

Logic Input NRST

VIL Input Low Level 0.5 V

VIH Input High Level 1.2 V

VDD_IO = 1.65V to VDD1,2

IIInput Current -1.0 1.0 µA

tNRST Reset Pulse Width 10 µs

Logic Input/Output SDA

VOL Output Low Level IOUT = 3 mA 0.3 0.5 V

ILOutput leakage current VOUT = 2.8V 1.0 µA

(1) Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics.

I2C Compatible Interface

I2C SIGNALS

The SCL pin is used for the I2C clock and the SDA pin is used for bidirectional data transfer. Both these signals

need a pull-up resistor according to I2C specification. The values of the pull-up resistors are determined by the

capacitance of the bus (typ. ~1.8 kΩ). Signal timing specifications are shown in table I2C Timing Parameters.

I2C DATA VALIDITY

The data on SDA line must be stable during the HIGH period of the clock signal (SCL). In other words, state of

the data line can only be changed when CLK is LOW.

Figure 13. I2C Signals: Data Validity

I2C START AND STOP CONDITIONS

START and STOP bits classify the beginning and the end of the I2C session. START condition is defined as SDA

signal transitioning from HIGH to LOW while SCL line is HIGH. STOP condition is defined as the SDA

transitioning from LOW to HIGH while SCL is HIGH. The I2C master always generates START and STOP bits.

The I2C bus is considered to be busy after START condition and free after STOP condition. During data

transmission, I2C master can generate repeated START conditions. First START and repeated START

conditions are equivalent, function-wise.

Product Folder Links: LP55271

start msb Chip Address lsb w ack msb Register Add lsb ack msb Data lsb ack stop

ack from slave ack from slave ack from slave

SCL

SDA

start Id = 4C w ack addr = ack ackaddress 02 data stop

02 hex

ADR6

Bit7 ADR5

bit6 ADR4

bit5 ADR3

bit4 ADR2

bit3 ADR1

bit2 ADR0

bit1 R/W

bit0

MSB LSB

I2C SLAVE address (chip address)

SDA

SCL SP

START condition STOP condition

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Figure 14. I2C Start and Stop Conditions

TRANSFERRING DATA

Every byte put on the SDA line must be eight bits long, with the most significant bit (MSB) being transferred first.

Each byte of data has to be followed by an acknowledge bit. The acknowledge related clock pulse is generated

by the master. The transmitter releases the SDA line (HIGH) during the acknowledge clock pulse. The receiver

must pull down the SDA line during the 9th clock pulse, signifying an acknowledge. A receiver which has been

addressed must generate an acknowledge after each byte has been received.

After the START condition, the I2C master sends a chip address. This address is seven bits long followed by an

eighth bit which is a data direction bit (R/W). The LP55271 address is 4C hex. For the eighth bit, a “0” indicates a

WRITE and a “1” indicates a READ. The second byte selects the register to which the data will be written. The

third byte contains data to write to the selected register.

When a READ function is to be accomplished, a WRITE function must precede the READ function, as shown in

the I2C Read Cycle waveform.

Figure 15. I2C Chip Address 4C hex for LP55271

w = write (SDA = “0”)

r = read (SDA = “1”)

ack = acknowledge (SDA pulled down by either master or slave)

rs = repeated start

id = chip address, 4C hex for LP55271.

Figure 16. I2C Write Cycle

Product Folder Links: LP55271

SDA

SCL

4 9

1 7

ack from slave

start msb Chip Address lsb

SCL

ack from slave

wmsb Register Add lsb rs r msb Data lsb stop

ack from slave ack from masterrepeated start data from slave

SDA

start Id = 4C w ack addr = 00 hex ack rs rack Address 00 hex data ack stop

msb Chip Address lsb

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Figure 17. I2C Read Cycle

Figure 18. I2C Timing Diagram

I2C TIMING PARAMETERS (VDD1,2 = 3.0 to 4.5V, VDDIO = 1.65V to VDD1,2)

Limit(1)

Symbol Parameter Unit

Min Max

1 Hold Time (repeated) START Condition 0.6 µs

2 Clock Low Time 1.3 µs

3 Clock High Time 600 ns

4 Setup Time for a Repeated START Condition 600 ns

5 Data Hold Time (Output direction, delay generated by LP55271) 300 900 ns

5 Data Hold Time (Input direction) 0 900 ns

6 Data Setup Time 100 ns

7 Rise Time of SDA and SCL 20+0.1Cb300 ns

8 Fall Time of SDA and SCL 15+0.1Cb300 ns

9 Set-up Time for STOP condition 600 ns

10 Bus Free Time between a STOP and a START Condition 1.3 µs

CbCapacitive Load for Each Bus Line 10 200 pF

(1) Specified by design. Not production tested.

Test Interface

The test bus can be controlled externally or internally. For the external control, the LP55271 pins VDD1,2 only

need to be powered. External control is independent on status of NRST and VDDIO pins. T1 is an input and it has

an internal 6 kΩpull-down resistor. T2 is an output line for the test result with an internal 200 kΩpull-down

resistor. When T1 is low, T2 is always pulled down; when T1 is high, T2 is indicating the result of the test.

Product Folder Links: LP55271

12 3

T2 DUT

OK LED1

OK LED2

OK LED3

OK LED4

OK FLED

PASS/

FAIL

COUNTER

FLASH

LED1

LED2

LED3

LED4

4.2V

500 PA

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Figure 19. High Level Schematic Representation of the Test Interface

The device is capable of detecting a defective unit in three cases:

•Production test 1: The LP55271 is assembled on a printed wiring board (PWB), but there is no LEDs

connected on current sink outputs. An external 4.2V test voltage is supplied on the VDD1 and VDD2 pins, from

which follows that the reset operating mode is entered with POR. Test pin T1 is pulled high. The chip will

send an acknowledge “1” onto the T2 pin if the chip is in working order; otherwise T2 stays low (0). Refer to

Test Interface Timing Diagram.

•Production test 2: The LP55271 is assembled on a PWB with the external components shown in LP55271

Block Diagram. 4.2V voltage is connected to VDD1, VDD2 and FB pins (see Figure 19), from which follows that

the reset operating mode is entered with POR. Test pin T1 is pulled high. The chip will send an acknowledge

“1” onto the T2 pin if the chip is in working order; otherwise T2 stays low (0). If the ACK is “1”, a repetitive test

pattern “0-1-0-1-0-1-0-1-0-1-0-1” is applied to T1 pin and if the LED corresponding the pattern (see Test

Interface Timing Diagram) is connected properly T2 gives “1”, otherwise T2 stays low. The last “1”

disengages the test.

•Field test: Build-in self-test through the I2C compatible control interface. The LP55271 is enabled

(NSTBY(bit) = 1, EN_BOOST(bit) = 1) and external test pins T1 and T2 are disconnected. The result can be

read through the I2C compatible control interface. LED test is enabled by writing to address 0Ch hex data

01h. Result can be read from the same address during the next I2C cycle. Note: I2C compatible interface

clock signal controls the timing of the test procedure. For that reason the clock signal frequency should be 50

kHz or less during the build-in self-test.

Figure 20. Test Interface Timing Diagram

Product Folder Links: LP55271

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Table 10. Test Interface Timing Parameters

Symbol Test Conditions Parameter Limit(1) Unit

Min Max

1 Setup Time after VDD1,2 = 4.2V 1 ms

2 Clock High Time 200 µs

3 VDD1,2 = 4.2V Clock Low Time 200 µs

4 Test Result Settling Time 10 µs

5 Data Hold Time 0 10 ns

(1) Specified by design. Not production tested.

Test Interface Characteristics

Limits in standard typeface are for TJ= 25ºC.

Symbol Parameter(1) Test Conditions Min Typ Max Unit

Logic Input T1

VIL Input Low Level 0.5 V

VDD1,2 = 4.2V

VIH Input High Level 1.2 V

Logic Output T2

VDD1,2 = 4.2V, IOUT = 3 mA

VOL Output Low Level 0.3 0.5 V

(pull-up current)

VDD1,2 = 4.2V, IOUT = -3 mA VDD1,2 -

VOH Output High Level 3.9 V

(pull-down current) 0,5

Internal Current Sink

ISINK Sink Current VDD1,2 = 4.2V 500 µA

Connectivity Test Pass Range

0.10 V

Voltage Over the Internal Current

VPASS1 Production test cases

Sink; Low Level -50 +50 %

VDD1,2 = 4.2V 2.90 V

Voltage Over the Internal Current VOUT = 3.9V to 4.2V

VPASS2 Sink; High Level -10 +10 %

0.40 V

Voltage Over the Internal Current

VPASS3 Field test cases

Sink; Low Level -30 +30 %

VDD1,2 = 3.0V to 4.2V 3.95 V

Voltage Over the Internal Current VOUT = 5.0V ± 5%

VPASS4 Sink; High Level -10 +10 %

(1) Specified by design. Not production tested.

Product Folder Links: LP55271

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

APPLICATION INFORMATION

Recommended External Components

OUTPUT CAPACITOR, COUT1, COUT2

The output capacitors COUT1, COUT2 directly affect the magnitude of the output ripple voltage. In general, the

higher the value of COUT, the lower the output ripple magnitude. Multilayer ceramic capacitors with low ESR are

the best choice. At the lighter loads, the low ESR ceramics offer a much lower VOUT ripple that the higher ESR

tantalums of the same value. At the higher loads, the ceramics offer a slightly lower VOUT ripple magnitude than

the tantalums of the same value. However, the dv/dt of the VOUT ripple with the ceramics is much lower that the

tantalums under all load conditions. Capacitor voltage rating must be sufficient, 10V is recommended

Some ceramic capacitors, especially those in small packages, exhibit a strong capacitance reduction

with the increased applied voltage. The capacitance value can fall to below half of the nominal

capacitance. Too low output capacitance can make the boost converter unstable.

INPUT CAPACITOR, CIN

The input capacitor CIN directly affects the magnitude of the input ripple voltage and to a lesser degree the VOUT

ripple. A higher value CIN will give a lower VIN ripple. Capacitor voltage rating must be sufficient, 10V or greater is

recommended.

OUTPUT DIODE, D1

The output diode for a boost converter must be chosen correctly depending on the output voltage and the output

current. The diode must be rated for a reverse voltage greater than the output voltage used. The average current

rating must be greater than the maximum load current expected, and the peak current rating must be greater

than the peak inductor current (~1.7A at maximum load). A Schottky diode should be used for the output diode.

Schottky diodes with a low forward voltage drop (VF) and fast switching speeds are ideal for increasing efficiency

in portable applications. Do not use ordinary rectifier diodes, since slow switching speeds and long recovery

times cause the efficiency and the load regulation to suffer. In Schottky barrier diodes reverse leakage current

increases quickly with the junction temperature. Therefore, reverse power dissipation and the possibility of

thermal runaway has to be considered when operating under high temperature conditions. Examples of suitable

diodes are Diodes Incorporated type DFLS220L, ON Semiconductor type MBRA210LT3 and Philips type

PMEG1020.

INDUCTOR, L1

The LP55271 high switching frequency enables the use of the small surface mount inductor. A 4.7 µH shielded

inductor is suggested for 2 MHz switching frequency. The inductor should have a saturation current rating higher

than the peak current it will experience during circuit operation (~1.7A at maximum load). Less than 300 mΩESR

is suggested for high efficiency. Open core inductors cause flux linkage with circuit components and interfere

with the normal operation of the circuit. This should be avoided. For high efficiency, choose an inductor with a

high frequency core material such as ferrite to reduce the core losses. To minimize radiated noise, use a toroid,

pot core or shielded core inductor. The inductor should be connected to the SW1 and SW2 pins as close to the

ICas possible. Example of a suitable inductor is TDK type VLCF5020T-4R7N1R7-1.

Table 11. Recommended External Components

Symbol Symbol Explanation Value Unit Type

CVDD1 VDD1 Bypass Capacitor 100 nF Ceramic, X5R

CVDD2 VDD2 Bypass Capacitor 100 nF Ceramic, X5R

COUT1,2 Output Capacitors from FB to GND 2 x 10 µF ± 10% µF Ceramic, X5R, 10V

CIN Input Capacitor from Battery Voltage to GND 10 ± 10% µF Ceramic, X5R, 10V

CVDDIO VDD_IO Bypass Capacitor 100 nF Ceramic, X5R

CVDDA VDDA Bypass Capacitor 4.7 µF Ceramic, X5R, 6.3V

C1,2 Audio Input Capacitors 47 nF Ceramic, X5R

RTOscillator Frequency Bias Resistor 82 kΩ1%

RFFlash Current Set Resistor for 370 mA Sink Current 1300 Ω1%

Product Folder Links: LP55271

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

Table 11. Recommended External Components (continued)

Symbol Symbol Explanation Value Unit Type

CVREF Reference Voltage Capacitor, between VREF and GND 100 nF Ceramic, X5R

L1Boost Converter Inductor 4.7 µH Shielded, low ESR,

ISAT ~1.7A

D1Rectifying Diode, VFat maxload 0.35 V Schottky diode

Flash LED User defined

LED1 to LED4

Product Folder Links: LP55271

LP55271

www.ti.com

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

Control Registers

Table 12. LP55271 Control Registers and Default Values

ADDR REGISTER D7 D6 D5 D4 D3 D2 D1 D0

(HEX)

00 LED Control Register safety_time flash_sync en_flash en_torch en_led1 en_led2 en_led3 en_led4

0 0 0 0 0 0 0 0

01 LED1 led1[7] led1[6] led1[5] led1[4] led1[3] led1[2] led1[1] led1[0]

0 0 0 0 0 0 0 0

02 LED2 led2[7] led2[6] led2[5] led2[4] led2[3] led2[2] led2[1] led2[0]

0 0 0 0 0 0 0 0

03 LED3 led3[7] led3[6] led3[5] led3[4] led3[3] led3[2] led3[1] led3[0]

0 0 0 0 0 0 0 0

04 LED4 led4[7] led4[6] led4[5] led4[4] led4[3] led4[2] led4[1] led4[0]

0 0 0 0 0 0 0 0

0B ENABLES nstby en_boost en_autoload freq_sel

0 0 1 0

0C LED Test Control led1_ok led2_ok led3_ok led4_ok flashled_ok en_test

r/o r/o r/o r/o r/o 0

0D Boost Output boost[3] boost[2] boost[1] boost[0]

0 1 1 1

2A Audio Sync Control1 gain_sel[2] gain_sel[1] gain_sel[0] dc_freq en_agc en_sync speed_ctrl[1] speed_ctrl[2]

0 0 0 0 0 0 0 0

2B Audio Sync Control2 threshold[3] threshold[2] threshold[1] threshold[0]

0 0 1 1

Product Folder Links: LP55271

LP55271

SNVS460A –SEPTEMBER 2006–REVISED MAY 2013

www.ti.com

REVISION HISTORY

Changes from Original (April 2013) to Revision A Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 23

Product Folder Links: LP55271

PACKAGE OPTION ADDENDUM

www.ti.com 29-Aug-2015

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LP55271TL/NOPB ACTIVE DSBGA YZR 30 TBD Call TI Call TI -30 to 85 D55B

LP55271TLX/NOPB ACTIVE DSBGA YZR 30 TBD Call TI Call TI -30 to 85 D55B

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

PACKAGE OPTION ADDENDUM

www.ti.com 29-Aug-2015

Addendum-Page 2

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

MECHANICAL DATA

YZR0030xxx

www.ti.com

TLA30XXX (Rev C)

0.600±0.075 D

. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.

B. This drawing is subject to change without notice.

NOTES:

4215057/A 12/12

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

LP55271TL/NOPB LP55271TLX/NOPB