Microwave Ceramics and Modules 2 - Pole Filter for Mobile Broadcasting (Frontend) Filter B69842N2647A627 Preliminary Datasheet Features * Extreme Low Losses in Passband (typ. 0.5dB) * High Power Durability * High attenuations at GSM, PDC, PHS, UMTS, and WLAN Bands * Excellent reflow solderability, no migration effect due to copper/tin metallization Index Page 2 * Dimension Limits * Recommended Footprint Page 3 * Characteristics * Maximum ratings * Typical passband characteristic Page 4 * Processing information * Soldering requirements * Delivery mode ISSUE DATE 5.08.02 ISSUE P1 PUBLISHER SAW MWC PD F PAGE 1/4 Microwave Ceramics and Modules 2 - Pole Filter for Mobile Broadcasting (Frontend) Filter B69842N2647A627 Preliminary Datasheet Dimension Limits 4.0 0.3 1.2 0.3 a I/O I/O a 5.8 0.3 G max 6.1 10.5 0.3 a = 0.90.4 Recommended Footprint I/O G G G ISSUE DATE Solder Pads: I/O Pads must be connected to lines with 50 impedance. In the application a termination of 50 must be realized. I/O G G 5.08.02 Ground, covered with solder resist, connected to lower ground plane by vias with maximum diameter of 0.3mm and max. distance of 1mm G ISSUE P1 PUBLISHER SAW MWC PD F PAGE 2/4 Microwave Ceramics and Modules 2 - Pole Filter for Mobile Broadcasting (Frontend) Filter B69842N2647A627 Preliminary Datasheet Characteristics (over whole temperature range) Center frequency Insertion loss min. fc - IL Passband (2629- 2656) typ. max. 2.6425 0.5 0.7 GHz dB B 27 MHz Amplitude ripple (peak - peak) Standing Wave Ratio / Return Loss [dB] Impedance Attenuation at DC to 440 MHz at 440 to 1525 MHz at 1525 to 1680 MHz at 1680 to 1980 MHz at 1980 to 2170 MHz at 2170 to 2500 MHz 0.1 0.2 1.12 / -25 1.5 / -14 50 57 40 38 34 30 27 60 44 41 38 33 29 dB dB dB dB dB dB 35 40 dB Z at 3450 MHz Maximum ratings IEC climatic category (IEC 68-1) dB - 40 /+ 90/56 Operating temperature Top - 40 / + 85 C Typical passband characteristics ISSUE DATE 5.08.02 ISSUE P1 PUBLISHER SAW MWC PD F PAGE 3/4 Microwave Ceramics and Modules 2 - Pole Filter for Mobile Broadcasting (Frontend) Filter B69842N2647A627 Preliminary Datasheet Processing information Wettability to IEC 68-2-58: 75% (after aging) Soldering Requirements Profile for eutectic SnPb solder paste Profile for leadfree solder paste Soldering type reflow Maximum soldering temperature 235 (max. 2 sec.) (measuring point on top surface of the component) 225 (max. 10 sec.) reflow 260 (max. 2 sec.) C 250 (max. 10 sec.) C Recommended soldering conditions (infrared): within 10 sec. Temp. [C] within 10 sec. Temp. [C] 245C5C 215C10C 20-40 sec. 30 sec. Time [sec.] 2.5 C/s 40-80 sec. 2-3 min. Time [sec.] > - 5 C/s Delivery mode * Blister tape acc. to IEC 286-3, grey * Pieces/tape: t.b.d EPCOS AG 2001. All Rights Reserved. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. The information contained in this data sheet describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. ISSUE DATE 5.08.02 ISSUE P1 PUBLISHER SAW MWC PD F PAGE 4/4