INTERFACE FOR MODULE T2 (32WAY) 4.55 +0.10 -0.30 38 0 37 2.00 -0.05 35 A 41 (43.5 MAX) 110 0 B -0.10 103 0 B -0.10 107 0.30 heral Perip 7 111 16.3 MIN P 0 D -0.10 2x 18.5 +0.2 0 108 B 0 C -0.10 F A B 0 1.8 -0.1 115 G E HEADERS CODINGS (CODING 3 SHOWN) (CODING 2 SHOWN) 114 A 12 21.60 +0.20 0 8 112 0 1.2 -0.1 0 C -0.10 0 15.40 -0.20 9 2 2x 18.5 +0.2 0 106 30 30.6 +0.2 -0.1 8.25 40.0 0.1 40 D 11 10 3 1 9 x 2.5 = 22.5 0 A -0.10 H 13 B 104 C A-A 14.85 REF. A AXIS 0 102 A -0.10 15 (h= 6.0) REF. A AXIS E A 42 0.10 A 1 14 47 8x R 10.95 0.05 39 14.55 0.25 0 14.45 -0.15 0 2.60 -0.05 48 0.10 B 4x R 3.0 0.1 3 x 4.2 = 12.60 (4x R 4.4) 15.95 0.05 6.30 6.30 8.25 F 2 SEAL AREA: NO DEFECT IN THIS AREA.(SPLIT LINE, BURRS, SINK MARK, SCRATCH, BURN... NOT ALLOWED) +0.1 51 8.3 -0.3 3 x 4.2 = 12.6 9.85 4.125 G (4x R 4.4) 5 x 2.5 = 12.50 3.7 34 8x R 49 3 INTERFACE FOR HYBRID MODULES T2 (32WAY) AND T3 (48 WAY) 24.55 0.25 50 45 4x R 3.0 0.1 30.0 0.1 30 3.5 4 INTERFACE FOR MODULE T3 (48WAY) (33.5 MAX) 31 0.10 A 5 6 4.125 H 7 8 WITHOUT DRAFT IN SEAL AREA (h=6) 9 21.0 0.1 10 18.5 +0.1 0 11 0 24.90 -0.30 12 0.10 B 13 0 D -0.10 HEADER'S CODINGS FOR MODULE T2 (32W) D HEADER'S CODINGS FOR MODULE T3 (48W) COLOR CODING DIM. A DIM. B DIM. C DIM. D COLOR CODING DIM. A DIM. B DIM. C DIM. D BLACK 1 9.1 4.3 5.9 4.3 BLACK 1 12.9 6.3 8.5 6.3 GREY 2 7.5 5.9 9.1 5.9 GREY 2 10.7 8.5 12.9 8.5 BROWN 3 5.9 7.5 9.1 9.1 BROWN 3 8.5 10.7 12.9 12.9 GREEN 4 7.5 9.1 4.3 4.3 GREEN 4 10.7 12.9 6.3 6.3 BLUE 5 4.3 7.5 5.9 5.9 BLUE 5 6.3 10.7 8.5 8.5 YELLOW 6 9.1 7.5 4.3 7.5 YELLOW 6 12.9 10.7 6.3 10.7 C 116 NOTE: 4x 1- INTERFACE DEFINITION BASED ON NFR13-462 STANDARD. 2- HEADER: ELASTICITY MODULUS: 8000Mpa min. (INITIAL CONDITION BEFORE AGEING) 0 14.45 -0.15 109 B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A B-B DOCUMENT STATUS 13 P1 RELEASE DATE 12 2018/09/03 11 08:17:38 10 9 SCALE mm 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) CODINGS FORMAT: master-tb-prod-A2 REVISION: H DATE: 2018/01/18 DIMENSION UNITS 8 7 6 ANGULAR TOL 2.0 4 PLACES 0.10 3 PLACES 0.10 2 PLACES 0.10 1 PLACE 0.10 0 PLACES DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 CURRENT REV DESC: NX RE-MASTERING EC NO: 603689 DRWN: SLAFAURE CHK'D: OPLESSIS APPR: SLAFAURE INITIAL REVISION: DRWN: G.DESBRUERES APPR: OPLESSIS FIRST ANGLE PROJECTION 4 2018/07/17 2018/08/31 2018/09/03 2008/10/02 2008/10/06 DRAWING SERIES A2-SIZE 98644 3 32 & 48CKT CMC INTERFACE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-98644-006 MATERIAL NUMBER PSD 001 CUSTOMER N/A GENERAL MARKET 2 B1 SHEET NUMBER 1 OF 3 1 A 13 12 11 10 9 7 8 5 6 4 3 2 1 PINS 0.635 DEFINITION TABS 1.5 DEFINITION GROUND TABS 1.5 DEFINITION PROTECTION WALL DEFINITION 5:1 5:1 5:1 5:1 H 52 0.63 +0.02 -0.03 67 1.5 0.1 0.8 +0.04 -0.03 74 69 Top 0.40 A 54 Top 0.40 A B 0 55 0.25 -0.15 FOR OTHER DIMENSIONS SEE TABS 1.5 DEFINITION 0.40 B Top 76 0 0.9 -0.2 0.15 B 96 95 4 0.4 0.1 77 70 0.75 0.25 H MI N 99 4x R 1.03 MAX 2x R 1.03 MAX 79 86 97 1.7 MIN 73 119 7.5 +0.1 -0.2 72 0.8 +0.3 0 65 0.8 0.3 58 6.7 0.2 0 0.6 -0.2 57 0 0.6 -0.2 6.7 0.2 64 G 8.1 0.2 G 1 98 R 0.3 MAX 100 F P 4x R 0.1 MAX P P 4x R 0.1 MAX P P P 80 66 1 : SHAPES ALLOWED LOCKING AXIS PROTECTION LOCKING AXIS DEFINITION 5:1 5:1 E F P E MANDATORY OVERTHICKNESS: dimension noted (*) IF THE LOCKING AXIS ARE OUT OF EQUIPMENT OVERALL DIMENSIONS. (2x R 0.5) 27 D 26 C J ( 5.6) 24 R 0.25 0.05 Peripheral 3.40 0.05 25 10.0 MIN D 13.4 MIN 29.5 MIN 0.8 C 19 (R 0.25 Peripheral) R 20.0 MIN 28 (R 0.3 Peripheral) ADMISSIBLE SHAPES WITH OVERTHICKNESS 0.2 MIN (*) B B 29 0.2 MIN (*) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DOCUMENT STATUS 13 SCALE mm 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) A FORMAT: master-tb-prod-A2 REVISION: H DATE: 2018/01/18 DIMENSION UNITS P1 RELEASE DATE 12 2018/09/03 11 08:17:38 10 9 8 7 6 ANGULAR TOL 2.0 4 PLACES 0.1 3 PLACES 0.1 2 PLACES 0.1 1 PLACE 0.1 0 PLACES DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 CURRENT REV DESC: NX RE-MASTERING EC NO: 603689 DRWN: GMANIVANNAN CHK'D: OPLESSIS APPR: SLAFAURE INITIAL REVISION: DRWN: GDESBRUERES APPR: OPLESSIS FIRST ANGLE PROJECTION 4 2018/07/17 2018/08/31 2018/09/03 2008/10/02 2008/10/06 DRAWING SERIES A2-SIZE 98644 3 32 & 48CKT CMC INTERFACE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-98644-006 MATERIAL NUMBER PSD 001 CUSTOMER N/A GENERAL MARKET 2 B1 SHEET NUMBER 2 OF 3 1 A 13 12 11 10 9 7 8 5 6 4 3 2 1 CONNECTOR ON HEADER - OVERALL DIMENSIONS LAYOUT FOR TWO INTERFACES T2 (32W) For Same Harness Exit Direction 40.0 Mini 10 MIN 20 MIN T2 T2 FOR INFORMATION FOR INFORMATION FOR INFORMATION UNLOCKED CONNECTOR - OVERALL DIMENSIONS 30 MIN H LOCKED CONNECTOR - OVERALL DIMENSIONS 10 MIN 35 MAX 10 MIN FOR INFORMATION FOR INFORMATION R 30 M AX 53.65 MAX T2 T3 E 53.5 Mini For Opposite Harness Exit Direction 6.15 MAX 0.3 MAX F 5.25 MAX 0.3 MAX 13.2 MAX UNLOCKED CONNECTOR - OVERALL DIMENSIONS 20 MIN 10 MIN FOR INFORMATION FOR INFORMATION 53.9 MAX FOR INFORMATION For Same Harness Exit Direction 39.5 Mini MODULE T2 (32W) 30 MIN F MULTI - HEADERS LAYOUT LAYOUT FOR TWO INTERFACES T2 (32W) AND T3 (48W) G 35.2 MAX G 50.0 Mini For Opposite Harness Exit Direction H 10 MIN LOCKED CONNECTOR - OVERALL DIMENSIONS E 10 MIN 35.05 MAX FOR INFORMATION FOR INFORMATION D LAYOUT FOR TWO INTERFACES T3 (48W) R 32 T3 MA X 55.65 MAX For Same Harness Exit Direction 44.5 Mini 37.2 MAX D T3 MODULE T3 (48W) C C 1.15 MAX 53.5 Mini For Opposite Harness Exit Direction 5.25 MAX NOTE: 1- T2 = 32 WAY / T3 = 48 WAY 10.45 MAX B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION LEGEND: A DOCUMENT STATUS 13 SCALE mm 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) FREE VOLUME FOR MANUAL LOCKING AND UNLOCKING DIMENSIONS GIVEN FOR INFORMATION ONLY BE CONFIRMED BASED UPON VEHICLE CONFIGURATION. FORMAT: master-tb-prod-A2 REVISION: H DATE: 2018/01/18 DIMENSION UNITS P1 RELEASE DATE 12 2018/09/03 11 ANGULAR TOL 2.0 4 PLACES 0.1 3 PLACES 0.1 2 PLACES 0.1 1 PLACE 0.1 0 PLACES DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:17:38 10 9 8 7 6 5 CURRENT REV DESC: NX RE-MASTERING EC NO: 603689 DRWN: SLAFAURE CHK'D: OPLESSIS APPR: SLAFAURE INITIAL REVISION: DRWN: GDESBRUERES APPR: OPLESSIS FIRST ANGLE PROJECTION 4 2018/07/17 2018/08/31 2018/09/03 2008/10/02 2008/10/06 DRAWING SERIES A2-SIZE 98644 3 32 & 48CKT CMC INTERFACE PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-98644-006 MATERIAL NUMBER PSD 001 CUSTOMER N/A GENERAL MARKET 2 B1 SHEET NUMBER 3 OF 3 1 A