MB95F816 Series of Microcontrollers : Fujitsu Semiconductor Pacific Asia Ltd. | China Home > Microcontrollers > New 8FX MCU > MB95F816 Series of Microcontrollers Home MB95F816 Series Further Information Part Number ASICs/Wafer Foundry Services About Us Structure drawing Microcontrollers 8 Bit MCUs Corporate Introduction Characteristic Summary News Documentation Events EVB & EVB Adaptor Recruitment BGMA Manual New 8FX MCU Contact Us USB Programmer Software 16 Bit MCUs ROM Flash Programming Tools 32 Bit MCUs Development Environment Company Information Agent List FlexRay MCU Development Environment Part Number Applications FAQ Ordering P/Ns Automotive MB95F816KPMC-GSNE2 Analog MB95F816KPMC1G-SNE2 Pin ROM Type ROM KB RAM Byte LVD I/O Operation Voltage(V) Max Operation Frequency MHz 32 1 58(MAX) 2.7-5.5 16.25 64 32KB/1KB Package LQFP64 0.65mm pin pitch LQFP64 0.5mm pin pitch Home Entertainment Wireless Solutions Structure drawing Memory Products Imaging Products Other Characteristic Summary Part Number MB95F816K Series Package LQFP64 Clock supervisor Counter It supervises the main clock oscillation and the subclock oscillation. Flash memory 32KB RAM 1KB Power on Reset Yes http://www.fujitsu.com/cn/fsp/mcu/mb95/mb95f816.html[6/25/2012 10:57:09 AM] MB95F816 Series of Microcontrollers : Fujitsu Semiconductor Pacific Asia Ltd. Low-voltage Yes detection Reset CPU Function Number of basic instructions : 136 Instruction bit length : 8 bits Instruction length : 1 to 3 bytes Data bit length : 1, 8 and 16 bits Minimum instruction execution time : 61.5 ns (with machine clock = 16.25 MHz) Interrupt processing time : 0.6 s (with machine clock = 16.25 MHz) I/O ports (Max): 58 Generalpurpose CMOS: 54 I/O N-ch.: 4 Timebase timer Interrupt cycle: 0.256 ms to 8.3 s (when external clock = 4 MHz) Reset generation cycle. Hardware/ Main oscillation clock at 10 MHz: 105 ms (Min). software The sub-internal CR clock can be used as the source clock of the watchdog timer hardware watchdog timer. Wild register It can be used to replace three bytes of data Wild register. LIN-UART A wide range of communication speeds can be selected by a dedicated reload timer. Clock-synchronized serial data transfer and clock-asynchronized serial data transfer is enabled. The LIN function can be used as a LIN master or a LIN slave. 8/10-bit A/D converter 12 channels 8-bit resolution and 10-bit resolution can be chosen. 2 Channels 8/16-bit composite timer The timer can be configured as an "8-bit timer x 2 channels" or a "16bit timer x 1 channel".It has built-in timer function, PWC function, PWM function and input capture function. Count clock: it can be selected from internal clocks (seven types) and external clocks. It can output square wave. 8 Channels External interrupt On-chip debug Interrupt by edge detection.(The rising edge, falling edge, or both edges can be selected.) It can be used to wake up the device from different standby modes. 1-wire serial control It supports serial writing. (asynchronous mode) 1 channel UART/SIO Data transfer with UART/SIO is enabled. It has a full duplex double buffer, variable data length (5/6/7/8 bits), a built-in baud rate generator and an error detection function. 1 channel I2C Master/slave transmission and receiving. It has the following functions: bus error function, an arbitration function, a transmission direction detection function and a wake-up function. It also has functions of generating and detecting repeated START conditions. 2channels 8/16 bit PPG Each channel can be used as an"8-bit timer X 2channels" or a "16-bit timer X 1channel". The counter operating clock can be selected from eight clock sources. 2 Channels 16 bit PPG timer 16-bit reload timer PWM mode and one-shot mode are available to use. The counter operating clock can be selected from eight clock sources. It supports external trigger start. Two clock modes and two counter operating modes are available to use. It can output square waveform. Count clock: it can be selected from internal clocks (seven types) and http://www.fujitsu.com/cn/fsp/mcu/mb95/mb95f816.html[6/25/2012 10:57:09 AM] MB95F816 Series of Microcontrollers : Fujitsu Semiconductor Pacific Asia Ltd. external clocks. Two counter operating modes: reload mode and one-shot mode. Watch prescaler Eight different time intervals can be selected. 2 Channels Comparator The reference voltage of each Channel can be selected between the BGR Voltage and the comparator pin. Standby mode There are four standby modes as follows: Sleep mode, stop mode, watch mode, timebase timer mode. In standby mode, The device can be make to enter deep standby mode. Flash memory It supports automatic programming(Embedded Algorithm), Program/erase/erase-suspend/erase-resume commands. It has a flag indicating the completion of the operation of Embedded Algorithm. Number of program/Erase cycles: 1000 / 10000 /100000 Data retention time: 20years/10years/5years Documentation Datasheet PDF English Hardware Manual PDF English Programmer Manual PDF prog8fx-cm26-00301-1e.pdf [2.06MB] EVB & EVB adapter EVB MB2146-530-E EV-board schematics BGMA Manual BGMA Manual MB2146-07-E USB Programmer Software USB Programmer Software PCWUSB-V01L07-MB95F200.zip ROM Flash Programming Tools Manufacturer Programmer / Adaptor Fujitsu MCU-AN-500028-E-14 Xeltek http://www.xeltek.com/device_search/search.php?company=2 Hilo http://www.hilosystems.com.tw/hilo/hilo04/hl4100.asp?menu=3 ZLG http://www.embedtools.com/programmer/fujitsu/ Development Environment Name Download MB95810 Series SOFTUNE SOFTUNE Application Note and Sample Code http://www.fujitsu.com/cn/fsp/mcu/mb95/mb95f816.html[6/25/2012 10:57:09 AM] MB95F816 Series of Microcontrollers : Fujitsu Semiconductor Pacific Asia Ltd. Site Map Fujitsu China Home http://www.fujitsu.com/cn/fsp/mcu/mb95/mb95f816.html[6/25/2012 10:57:09 AM] Copyright 2005 - 2012 FUJITSU SEMICONDUCTOR PACIFIC ASIA LTD. ICP05052384