MC74HC373A Octal 3-State Non-Inverting Transparent Latch High-Performance Silicon-Gate CMOS The MC74HC373A is identical in pinout to the LS373. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. These latches appear transparent to data (i.e., the outputs change asynchronously) when Latch Enable is high. When Latch Enable goes low, data meeting the setup and hold time becomes latched. The Output Enable input does not affect the state of the latches, but when Output Enable is high, all device outputs are forced to the high-impedance state. Thus, data may be latched even when the outputs are not enabled. The HC373A is identical in function to the HC573A which has the data inputs on the opposite side of the package from the outputs to facilitate PC board layout. The HC373A is the non-inverting version of the HC533A. * * * * * * * Output Drive Capability: 15 LSTTL Loads Outputs Directly Interface to CMOS, NMOS and TTL Operating Voltage Range: 2.0 to 6.0 V Low Input Current: 1.0 A High Noise Immunity Characteristic of CMOS Devices In Compliance with the Requirements Defined by JEDEC Standard No. 7A Chip Complexity: 186 FETs or 46.5 Equivalent Gates http://onsemi.com MARKING DIAGRAMS 20 PDIP-20 N SUFFIX CASE 738 20 MC74HC373AN AWLYYWW 1 20 1 20 1 SOIC WIDE-20 DW SUFFIX CASE 751D HC373A AWLYYWW 1 20 HC 373A ALYW TSSOP-20 DT SUFFIX CASE 948E 20 1 1 SOEIAJ-20 F SUFFIX CASE 967 20 20 74HC373A AWLYWW 1 1 A WL YY WW = Assembly Location = Wafer Lot = Year = Work Week ORDERING INFORMATION Device Package Shipping PDIP-20 1440 / Box MC74HC373ADW SOIC-WIDE 38 / Rail MC74HC373ADWR2 SOIC-WIDE 1000 / Reel MC74HC373ADT TSSOP-20 75 / Rail MC74HC373AN Semiconductor Components Industries, LLC, 2001 November, 2001 - Rev. 10 1 MC74HC373ADTR2 TSSOP-20 2500 / Reel MC74HC373AF SOEIAJ-20 1600 / Box MC74HC373AFEL SOEIAJ-20 2000 / Reel Publication Order Number: MC74HC373A/D MC74HC373A PIN ASSIGNMENT LOGIC DIAGRAM D0 D1 D2 DATA INPUTS D3 D4 D5 D6 D7 LATCH ENABLE OUTPUT ENABLE 3 2 4 5 7 6 8 9 13 12 14 15 17 16 18 19 11 1 Q0 Q1 Q2 Q3 NONINVERTING OUTPUTS Q4 Q5 VCC 2 19 Q7 D0 3 18 D7 D1 4 17 D6 Q1 5 16 Q6 Q2 6 15 Q5 D2 7 14 D5 D3 8 13 D4 Q3 9 12 Q4 10 11 LATCH ENABLE FUNCTION TABLE Q7 Inputs Output Enable PIN 20 = VCC PIN 10 = GND Units Internal Gate Count* 46.5 ea Internal Gate Propagation Delay 1.5 ns 5.0 W 0.0075 pJ Speed Power Product *Equivalent to a two-input NAND gate. 20 Q6 Value Internal Gate Power Dissipation 1 GND IIIIIIIIIII IIII III IIIIIIIIIII IIII III IIIIIIIIIII IIII III IIIIIIIIIII IIII III IIIIIIIIIII IIII III IIIIIIIIIII IIII III Design Criteria OUTPUT ENABLE Q0 http://onsemi.com 2 Latch Enable L H L H L L H X X = Don't Care Z = High Impedance Output D Q H L X X H L No Change Z MC74HC373A IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII IIIII III IIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III IIII IIIIIIIIIIIIII IIIII III MAXIMUM RATINGS* Symbol Parameter Value Unit - 0.5 to + 7.0 V DC Input Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V DC Output Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V VCC DC Supply Voltage (Referenced to GND) Vin Vout Iin DC Input Current, per Pin 20 mA Iout DC Output Current, per Pin 35 mA ICC DC Supply Current, VCC and GND Pins 75 mA PD Power Dissipation in Still Air, 750 500 450 mW Tstg Storage Temperature - 65 to + 150 C TL Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP, SOIC, SSOP or TSSOP Package) Plastic DIP SOIC Package TSSOP Package This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND (Vin or Vout) VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. C 260 *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Derating -- Plastic DIP: - 10 mW/C from 65 to 125C SOIC Package: - 7 mW/C from 65 to 125C TSSOP Package: - 6.1 mW/C from 65 to 125C For high frequency or heavy load considerations, see Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). IIII IIIIIIIIIIIIIII III II III IIII IIIIIIIIIIIIIII III II III IIII IIIIIIIIIIIIIII III II III IIII IIIIIIIIIIIIIII III II III IIII IIIIIIIIIIIIIII III II III IIII IIIIIIIIIIIIIII III II III IIII IIIIIIIIIIIIIII III III II IIII IIIIIIIIIIIIIII III III II IIII IIIIIIIII IIIIIIIII IIII IIIIIIIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIIIIIIII IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III RECOMMENDED OPERATING CONDITIONS Symbol VCC Vin, Vout Parameter Min Max Unit 2.0 6.0 V 0 VCC V - 55 + 125 C 0 0 0 1000 500 400 ns DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Test Conditions VCC V - 55 to 25C 85C 125C Unit VIH Minimum High-Level Input Voltage Vout = VCC - 0.1 V |Iout| 20 A 2.0 3.0 4.5 6.0 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 1.5 2.1 3.15 4.2 V VIL Maximum Low-Level Input Voltage Vout = 0.1 V |Iout| 20 A 2.0 3.0 4.5 6.0 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 0.5 0.9 1.35 1.8 V VOH Minimum High-Level Output Voltage Vin = VIH |Iout| 20 A 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 3.0 4.5 6.0 2.48 3.98 5.48 2.34 3.84 5.34 2.2 3.7 5.2 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 3.0 4.5 6.0 0.26 0.26 0.26 0.33 0.33 0.33 0.4 0.4 0.4 |Iout| 2.4 mA |Iout| 6.0 mA |Iout| 7.8 mA Vin = VIH VOL Maximum Low-Level Output Voltage Vin = VIL |Iout| 20 A Vin = VIL |Iout| 2.4 mA |Iout| 6.0 mA |Iout| 7.8 mA http://onsemi.com 3 V MC74HC373A IIII IIIIIIIII IIIIIIIII IIII IIIIIIIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIIIIIIII IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIII IIIIIIIII IIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIIIIIIII III IIII III IIII IIIII IIIIIIIIIIIIIIII IIII IIIIIIIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III IIIII IIIIIIIIIIIIIIII IIII IIII III IIII III DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Test Conditions VCC V - 55 to 25C 85C 125C Unit Iin Maximum Input Leakage Current Vin = VCC or GND 6.0 0.1 1.0 1.0 A IOZ Maximum Three-State Leakage Current Output in High-Impedance State Vin = VIL or VIH Vout = VCC or GND 6.0 0.5 5.0 10 A ICC Maximum Quiescent Supply Current (per Package) Vin = VCC or GND Iout = 0 A 6.0 4.0 40 160 A NOTE: Information on typical parametric values can be found in Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6.0 ns) Guaranteed Limit Symbol Parameter VCC V - 55 to 25C 85C 125C Unit tPLH tPHL Maximum Propagation Delay, Input D to Q (Figures 1 and 5) 2.0 3.0 4.5 6.0 125 80 25 21 155 110 31 26 190 130 38 32 ns tPLH tPHL Maximum Propagation Delay, Latch Enable to Q (Figures 2 and 5) 2.0 3.0 4.5 6.0 140 90 28 24 175 120 35 30 210 140 42 36 ns tPLZ tPHZ Maximum Propagation Delay, Output Enable to Q (Figures 3 and 6) 2.0 3.0 4.5 6.0 150 100 30 26 190 125 38 33 225 150 45 38 ns tPZL tPZH Maximum Propagation Delay, Output Enable to Q (Figures 3 and 6) 2.0 3.0 4.5 6.0 150 100 30 26 190 125 38 33 225 150 45 38 ns tTLH tTHL Maximum Output Transition Time, Any Output (Figures 1 and 5) 2.0 3.0 4.5 6.0 60 23 12 10 75 27 15 13 90 32 18 15 ns Cin Maximum Input Capacitance 10 10 10 pF Cout Maximum Three-State Output Capacitance (Output in High-Impedance State) 15 15 15 pF NOTE: For propagation delays with loads other than 50 pF, and information on typical parametric values, see Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). Typical @ 25C, VCC = 5.0 V CPD Power Dissipation Capacitance (Per Enabled Output)* 36 pF * Used to determine the no-load dynamic power consumption: P D = CPD VCC2 f + ICC VCC . For load considerations, see Chapter 2 of the ON Semiconductor High-Speed CMOS Data Book (DL129/D). http://onsemi.com 4 MC74HC373A IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIII III III IIIIIIIIIIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIIIIIIIIIIII III III IIIII IIIII IIIII II IIIIIIIIIIIII IIII IIIIIIIIIIIII III III III III III III III III II IIIII IIIII IIIII IIII IIIIIIIIIIIII III III III III III III III III II IIII IIIIIIIIIIIII III III III III III III III III II IIII IIIIIIIIIIIII III III III III III III III III II II IIII IIIIIIIIIIIII III III III III III III III III IIII IIIIIIIIIIIII III III III III III III III IIIII IIII IIIIIIIIIIIII III III III III III III III III II II IIII IIIIIIIIIIIII III III III III III III III III IIII IIIIIIIIIIIII III III III III III III III III II IIII IIIIIIIIIIIII III III III III III III III III II II IIII IIIIIIIIIIIII III III III III III III III III IIII IIIIIIIIIIIII III III III III III III III IIIII IIII IIIIIIIIIIIII III III III III III III III III II IIII IIIIIIIIIIIII III III III III III III III IIIII TIMING REQUIREMENTS (CL = 50 pF, Input tr = tf = 6.0 ns) Guaranteed Limit Symbol Parameter Fig. VCC Volts 85C - 55 to 25C Min Max Min 125C Max Min Max Unit tsu Minimum Setup Time, Input D to Latch Enable 4 2.0 3.0 4.5 6.0 25 20 5.0 5.0 30 25 6.0 6.0 40 30 8.0 7.0 ns th Minimum Hold Time, Latch Enable to Input D 4 2.0 3.0 4.5 6.0 5.0 5.0 5.0 5.0 5.0 5.0 50 5.0 5.0 5.0 5.0 5.0 ns tw Minimum Pulse Width, Latch Enable 2 2.0 3.0 4.5 6.0 60 23 12 10 75 27 15 13 90 32 18 15 ns tr, tf Maximum Input Rise and Fall Times 1 2.0 3.0 4.5 6.0 1000 800 500 400 1000 800 500 400 1000 800 500 400 ns SWITCHING WAVEFORMS tr tf INPUT D tPLH tPHL 90% 50% 10% Q tw VCC 90% 50% 10% LATCH ENABLE GND GND Q Figure 1. OUTPUT ENABLE VCC GND tPLZ 50% tPZH Q 50% Figure 2. 50% tPZL Q tPHL tPLH tTHL tTLH VCC 50% 10% VOL 90% VOH tPHZ 1.3 V VALID HIGH IMPEDANCE INPUT D tsu LATCH ENABLE Figure 4. http://onsemi.com 5 th 50% HIGH IMPEDANCE Figure 3. VCC 50% GND VCC GND MC74HC373A TEST CIRCUITS TEST POINT TEST POINT OUTPUT DEVICE UNDER TEST DEVICE UNDER TEST CL* CONNECT TO VCC WHEN TESTING tPLZ AND tPZL. CONNECT TO GND WHEN TESTING tPHZ AND tPZH. 1 k OUTPUT CL* *Includes all probe and jig capacitance *Includes all probe and jig capacitance Figure 5. Figure 6. EXPANDED LOGIC DIAGRAM D0 3 D1 4 D Q D2 7 D LE Q D3 8 D LE Q D4 13 D LE Q D5 14 D LE Q D6 17 D LE Q D7 18 D LE Q D LE Q LE 11 1 2 Q0 5 Q1 6 Q2 9 Q3 12 Q4 15 Q5 16 Q6 19 Q7 PACKAGE DIMENSIONS PDIP-20 N SUFFIX PLASTIC DIP PACKAGE CASE 738-03 ISSUE E -A- 20 11 1 10 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. B L C -T- K SEATING PLANE M N E G F J D 0.25 (0.010) 20 PL 0.25 (0.010) 20 PL M T A M http://onsemi.com 6 M T B M DIM A B C D E F G J K L M N INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0 15 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0 15 0.51 1.01 MC74HC373A PACKAGE DIMENSIONS SO-20 DW SUFFIX CASE 751D-05 ISSUE F A 20 X 45 M E h 0.25 H 10X NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 B M D 1 10 20X B 0.25 DIM A A1 B C D E e H h L B T A M S B S L A 18X e A1 20X 0.15 (0.006) T U 2X L/2 C T TSSOP-20 DT SUFFIX CASE 948E-02 ISSUE A K REF 0.10 (0.004) S SEATING PLANE 20 M T U S V S K K1 IIII IIII IIII 11 J J1 B -U- L PIN 1 IDENT SECTION N-N 1 10 0.25 (0.010) N 0.15 (0.006) T U S M A -V- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. N F DETAIL E -W- C D G H DETAIL E 0.100 (0.004) -T- SEATING PLANE http://onsemi.com 7 MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0 7 DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0 8 INCHES MIN MAX 0.252 0.260 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0 8 MC74HC373A PACKAGE DIMENSIONS SOEIAJ-20 F SUFFIX CASE 967-01 ISSUE O 20 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 11 Q1 M E HE 1 L 10 DETAIL P Z D VIEW P e A c A1 b 0.13 (0.005) M 0.10 (0.004) DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 12.35 12.80 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 0 0.70 0.90 --0.81 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.486 0.504 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 0 0.028 0.035 --0.032 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 MC74HC373A/D