11
notice_e-01
Notice for TAIYO YUDEN products 
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2010. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called TAIYO YUDENs official sales channel).
It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to Foreign Exchange and For-
eign Trade Control Law of Japan, U.S. Export Administration Regulations, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
110
11
leaded_i01_e-01
■ FEATURES
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/STANDARD QUANTITY
■ APPLICATIONS
■ AVAILABLE INDUCTANCE RANGE
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ Extremely reliable inductors that are ideal for automatic insertion.
◦ Highly efficient automated production processes can provide high
quality inductors in large volumes.
◦ Wide selection of configurations including axial leaded, formed radial leads
and bulk products to meet most manufacturing needs.
◦ Use for TVs, DVD, audio equipment, communication instrument,
tuner, and general electrical instrument.
AXIAL LEADED INDUCTORS
Type
Dimensions ［mm］（inch）Taped Bulk Standard Quantity (pcs)
LφDφd Straight Formed Straight Formed Lead Configuration Code
TA TB VD NA KR
LAL02 3.4max.
（0.134max.）
2.3max.
（0.091max.）
0.5±0.05
（0.018±0.002）——— 2,000 500 2,000
LAP02 3.4max.
（0.134max.）
2.3max.
（0.091max.）0.45±0.05
（0.018±0.002）——— ——— 2,000 ー2,000
LAN02 3.6max.
（0.142max.）
2.4max.
（0.094max.）
Unit：mm （inch）
Range Type LAL/LAP02 LAN02
Imax[A] Rdc max[Ω] Imax[A] Rdc max[Ω]
0.1
1270
0.22
0.8 500 0.32
10 160 2.5 280 1.0
100 44 12 120 5.6
1000
220
470
Inductance ［μH］
❶Type
LA Axial leaded
inductor
❹Lead configurations
KR Formed lead/bulk
NA Axial lead/bulk
TA Axial lead (26mm lead space)
/ammo pack
TB Axial lead (52mm lead space)
/ammo pack
VD Formed lead/ammo pack
❺Nominal inductance
〔μH〕
example
1R5 1.5
120 12
※R=decimal point
❻Inductance tolerance
〔％〕
J±5
K±10
❼Internal code
△△△△△ Standard product
△＝Blank space
❸Dimensions
（L×D）〔mm〕 max
02
3.4×2.3（LAL/LAP）
3.6×2.4（LAN）
❷Product Specification
L△Standard type
N△High current type
P△Standard type
（Lead diameter：0.45φmm）
△＝Blank space
L A L △0 2 T B R 2 2 K ○○○○○
❶❷❸❹ ❺❻ ❼
TB
Pitch：5mm（0.197）
VD NA
TA KR
Pitch：5mm（0.197）
0.12
WAV E
FERRITE PRODUCTS
111
11
leaded_i01_e-01
■ PART NUMBERS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
●LAL/LAP02
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Measuring
frequency
[MHz]
Selfーresonant
frequency
[MHz] (min.)
DC Resistance
[Ω] (max.)
Rated current
[mA] (max.)
LA□ 02 ○ R22K RoHS 0.22
±10％
35 25.2
450 0.40 400
LA□ 02 ○ R27K RoHS 0.27 410 0.43 380
LA□ 02 ○ R33K RoHS 0.33 360 0.48 370
LA□ 02 ○ R39K RoHS 0.39 300 0.51 350
LA□ 02 ○ R47K RoHS 0.47 230 0.56 330
LA□ 02 ○ R56K RoHS 0.56 210 0.61 320
LA□ 02 ○ R68K RoHS 0.68 190 0.67 310
LA□ 02 ○ R82K RoHS 0.82 170 0.74 290
LA□ 02 ○ 1R0K RoHS 1.0 150 0.80 270
LA□ 02 ○ 1R 2K RoHS 1.2
40
7.96
110 0.9 260
LA□ 02 ○ 1R5K RoHS 1.5 80 1.0 250
LA□ 02 ○ 1R8K RoHS 1.8 60 1.1 240
LA□ 02 ○ 2R2K RoHS 2.2 45 1.2 230
LA□ 02 ○ 2R7K RoHS 2.7 40 1.3 220
LA□ 02 ○ 3R3K RoHS 3.3 38 1.4 210
LA□ 02 ○ 3R9K RoHS 3.9 35 1.6 200
LA□ 02 ○ 4R7K RoHS 4.7 32 1.7 190
LA□ 02 ○ 5R6K RoHS 5.6 30 1.9 180
LA□ 02 ○ 6R8K RoHS 6.8 28 2.0 175
LA□ 02 ○ 8R2K RoHS 8.2 26 2.2 165
LA□ 02 ○ 100K RoHS 10 24 2.5 160
LA□ 02 ○ 120K RoHS 12
2.52
22 2.5 150
LA□ 02 ○ 150K RoHS 15 20 2.8 145
LA□ 02 ○ 180K RoHS 18 18 3.1 140
LA□ 02 ○ 220K RoHS 22 17 3.4 130
LA□ 02 ○ 270K RoHS 27 16 4.3 80
LA□ 02 ○ 330K RoHS 33 14 4.7 76
LA□ 02 ○ 390K RoHS 39 13 5.2 74
LA□ 02 ○ 470K RoHS 47 12 5.8 70
LA□ 02 ○ 560K RoHS 56 11 6.4 68
LA□ 02 ○ 680K RoHS 68 10 7.2 64
LA□ 02 ○ 820K RoHS 82 9.5 11 46
LA□ 02 ○ 101K RoHS 100 9.0 12 44
LA□ 02 ○ 121K RoHS 120
40 0.796
8.0 13 42
LA□ 02 ○ 151K RoHS 150 6.0 16 39
LA□ 02 ○ 181K RoHS 180 5.5 18 37
LA□ 02 ○ 221K RoHS 220 5.0 20 35
□ Please specify the Product Specification（Lead）code.（L:standard 0.5mm or P:0.45mm）
○ Please specify the Lead configuration code.
112
11
leaded_i01_e-01
■ PART NUMBERS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
●FAN02
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Measuring
frequency
[MHz]
Selfーresonant
frequency
[MHz] (min.)
DC Resistance
[Ω] (max.)
Rated current
[mA] (max.)
LAN02 ○ R12K RoHS 0.12
±10％
50
25.2
500 0.12 850
LAN02 ○ R15K RoHS 0.15 500 0.14 800
LAN02 ○ R18K RoHS 0.18 500 0.15 760
LAN02 ○ R22K RoHS 0.22 500 0.16 730
LAN02 ○ R27K RoHS 0.27 500 0.18 690
LAN02 ○ R33K RoHS 0.33 480 0.19 660
LAN02 ○ R39K RoHS 0.39 430 0.21 640
LAN02 ○ R47K RoHS 0.47 380 0.23 610
LAN02 ○ R56K RoHS 0.56 350 0.25 580
LAN02 ○ R68K RoHS 0.68 310 0.27 550
LAN02 ○ R82K RoHS 0.82 270 0.29 520
LAN02 ○ 1R0J RoHS 1.0
±5％
240 0.32 500
LAN02 ○ 1R2J RoHS 1.2
7.96
210 0.35 480
LAN02 ○ 1R5J RoHS 1.5 190 0.38 450
LAN02 ○ 1R8J RoHS 1.8 140 0.42 430
LAN02 ○ 2R2J RoHS 2.2 90 0.47 410
LAN02 ○ 2R7J RoHS 2.7 70 0.52 390
LAN02 ○ 3R3J RoHS 3.3 50 0.57 370
LAN02 ○ 3R9J RoHS 3.9
40
35 0.63 360
LAN02 ○ 4R7J RoHS 4.7 32 0.69 340
LAN02 ○ 5R6J RoHS 5.6 30 0.75 320
LAN02 ○ 6R8J RoHS 6.8 28 0.84 310
LAN02 ○ 8R2J RoHS 8.2 26 0.92 290
LAN02 ○ 100J RoHS 10 24 1.0 280
LAN02 ○ 120J RoHS 12
2.52
22 1.0 280
LAN02 ○ 150J RoHS 15 20 1.2 265
LAN02 ○ 180J RoHS 18 18 1.3 250
LAN02 ○ 220J RoHS 22 17 1.5 235
LAN02 ○ 270J RoHS 27 15 1.7 220
LAN02 ○ 330J RoHS 33
50
14 2.2 180
LAN02 ○ 390J RoHS 39 13 2.4 170
LAN02 ○ 470J RoHS 47 12 2.8 160
LAN02 ○ 560J RoHS 56 10 4.1 140
LAN02 ○ 680J RoHS 68 9.2 4.5 130
LAN02 ○ 820J RoHS 82 8.8 5.0 125
LAN02 ○ 101J RoHS 100 8.0 5.6 120
LAN02 ○ 121J RoHS 120
0.796
6.6 9.2 90
LAN02 ○ 151J RoHS 150 5.8 10.5 85
LAN02 ○ 181J RoHS 180 5.4 11.5 80
LAN02 ○ 221J RoHS 220 4.8 13 75
LAN02 ○ 271J RoHS 270 3.6 16 70
LAN02 ○ 331J RoHS 330 3.4 18 66
LAN02 ○ 391J RoHS 390 3.2 20 63
LAN02 ○ 471J RoHS 470 3.0 22 60
○ Please specify the Lead configuration code.
FERRITE PRODUCTS
113
11
leaded_i01_e-01
■ ELECTRICAL CHARACTERISTICS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
LAL/LAP02
LAL/LAP02
LAL/LAP02
LAN02
LAN02TA100J
LAN02TA101J
（Measured by HP4285A）
■
DC Bias characteristics
（Measured by HP4285A+HP42851A）
■
Q-Characteristics
（Measured by HP4285A）
■
Temperature characteristics
11
leaded_i01_pack-P1
leaded_i01_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦Taping for Straight Leads
◦Taping for Formed Leads
◦Bulk
①Minimum Quantity
Type Lead Configuration code Standard quantity (pcs.)
LAL02 TB 2,000
LAP02 TA 2,000
LAN02 TA 2,000
Type Lead Configuration code Standard quantity (pcs.)
LAL02 VD 2,000
Type Lead Configuration code Standard quantity (pcs.)
LAL02 NA 500
LAP02 KR 2,000
LAN02 KR 2,000
②Dimension
◦NA
◦VD
◦KR
◦TA（a：26mm lead space）
（1.02 inch）
◦TB（a：52mm lead space）
（2.05 inches）
1
L1
L1
Type Dimensions Minimum
insertion pitch
φD L φdℓ
LAL022.3max 3.4max 0.50±0.05 24±2.0 5.0
（0.091max）（0.134max）
（0.020±0.002）（0.945±0.079）
（0.197）
Unit：mm（inch）
Type
Lead configuration
code
Dimensions
φD F1φd b
LAP02 KR 2.3max 5.0±0.5 0.45±0.05 7.0±1.0
（0.091max）
（0.197±0.020）（0.018±0.002）（0.276±0.039）
LAN02 KR
2.4max 5.0±0.5 0.45±0.05 7.0±1.0
（0.094max）
（0.197±0.020）（0.018±0.002）（0.276±0.039）
Unit：mm（inch）
Type
Dimensions
Minimum
insertion
pitch
φD L a b |L1-L2|φd
LAP02 2.3max 3.4max 26＋0.5
－00.8max 0.5max
0.45±0.05
5.0
（0.091max）（0.134max）
（1.02
＋0.020
－0
）
（0.031max）（0.020max）
（0.018±0.002）
（0.197）
LAN02 2.4max 3.6max 26＋0.5
－00.8max 0.5max
0.45±0.05
5.0
（0.094max）（0.142max）
（1.02
＋0.020
－0
）
（0.031max）（0.020max）
（0.018±0.002）
（0.197）
Unit：mm（inch）
Type
Dimensions
Minimum
insertion
pitch
φD L a b |L1-L2|φd
LAL02 2.3max 3.4max 52＋2
－11.2max 1.0max
0.5±0.05
5.0
（0.091max）（0.134max）
（2.05
＋0.079
－0.039
）
（0.047max）（0.039max）
（0.020±0.002）
（0.197）
Unit：mm（inch）
Type Symbol Dimensions Symbol Dimensions
LAL02
A3.9max W18.0＋1.0
－0.5
（0.154max）（0.709＋0.039
－0.020 ）
φD2.3max W0
12.5 min.
（0.091max） （0.492 min.）
H19.5±0.5 W1
9.0＋0.75
－0.5
（0.768±0.020）（0.354＋0.030
－0.020 ）
P12.7±1.0 W2
3.0 max.
（0.500±0.039） （0.118 max.）
P0
12.7±0.3 ℓ2.0 max.
（0.500±0.012） （0.079 max.）
P1
3.85±0.7
φD0
4.0±0.3
（0.152±0.028）
P2
6.35±0.5 （0.157±0.012）
（0.250±0.020）
F5.08±0.5 φd0.50±0.05
（0.200±0.020） （0.020±0.002）
△h0±1.0 L11.0 max.
（0±0.039） （0.433 max.）
ー ー t0.5±0.2
（0.020±0.008）
Unit：mm（inch）
114
11
leaded_i02_e-01
■ FEATURES
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/STANDARD QUANTITY
■ APPLICATIONS
■ AVAILABLE INDUCTANCE RANGE
■ OPERATING TEMP.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ The LHL08~LHL16 series radial inductors are encapsulated in a resin
housing which adds to the stability of the mounted part on a printed
circuit board.
◦ The LHL08/LHL10/LHL13/LHL16 series are for high current applica-
tions.
◦ The LHLP10/LHLP12/LHLP16 series are shielded type for high current ap-
plications.
◦ LHLP10 series is also available in packaging.
◦ Ideal for use as a power choke coil in general household appliances
(TVS, PDPTV, LCDTV, DVD, etc) and industrial equipment.
◦ Can also be used as a peaking coil in filtering applications.
RADIAL LEADED INDUCTORS
Type Fig. D H2ℓFφdStandard Quantity (pcs)
Box Bulk Taped
LHL08 9.0 max. 9.5 max. 5.0±1.0 5.0±1.0 0.6±0.05 ー100 1000
（0.354 max.） （0.374 max.） （0.197±0.039） （0.197±0.039） （0.024±0.002）
LHL10 11.0 max. 14.0 max. 5.0±1.0 5.0±1.0 0.6±0.05 ー50 500
（0.433 max.） （0.551 max.） （0.197±0.039） （0.197±0.039） （0.024±0.002）
LHL13 14.0 max. 17.0 max. 5.0±1.0 7.5±1.0 0.8±0.05 ー25 500
（0.551 max.） （0.669 max.） （0.197±0.039） （0.295±0.039） （0.031±0.002）
LHL16 17.0 max. 21.0 max. 5.0±1.0 7.5±1.0 0.8±0.05 500 ー250
（0.669 max.） （0.827 max.） （0.197±0.039） （0.295±0.039） （0.031±0.002）
LHLP10 11.0 max. 11.0 max. 5.0±1.0 5.0±1.0 0.6±0.05 500 ー200
（0.433 max.） （0.433 max.） （0.197±0.039） （0.197±0.039） （0.024±0.004）
LHLP12 13.0 max. 16.0 max. 5.0±1.0 5.0±1.0 0.6±0.05 300 ー ー
（0.512 max.） （0.624 max.） （0.197±0.039） （0.197±0.039） （0.024±0.004）
LHLP16 17.0 max. 19.0 max. 5.0±1.0 7.5±1.0 0.8±0.05 200 ー ー
（0.669 max.） （0.741 max.） （0.197±0.039） （0.295±0.039） （0.031±0.004）
Unit：mm （inch）
Range Type LHL08 LHL10 LHL13 LHL16 LHLP10 LHLP12 LHLP16
0.22μ
1.0μ1.0μ
10μ
3.3μ
10μ10μ10μ
100μ
47μ15μ
1.0m
10m
1.0m 1.0m 1.0m
100m
33m 10m 10m
150m
Inductance ［H］
❶Type
LH Radial leaded inductor
❹Packaging Code
NB Bulk (LHL)
TB
Ammo packaging (LHL)
❺Nominal Inductance
(μH)
example
1R0 1.0
150 15
102 1000
※R=Decimal point
❻Inductance
Tolerances (％)
J±5
K±10
M±20
N±30
❼Internal code
△△△ Standard product
△＝Blank space
❸External
dimensions
〔mm max〕
08 9.0
10 11.0
12 13.0
13 14.0
16 17.0
❷Configuration
L△Standard type Taping available
LP Shielded type Bulk
△＝Blank space
L H △L△0 8 T B 1 0 1 K ○○○
❶ ❷❸❹ ❺❻❼
WAV E
◦ ー25℃～105℃（Including self-generated heat）
FERRITE PRODUCTS
115
11
leaded_i02_e-01
■ PART NUMBERS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
●LHL08
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
（min.）
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
Measuring
frequency
〔MHz〕
LHL08□1R0N RoHS 1.0 ±30％
40
76 0.013 4.7
7.96
LHL08□1R5M RoHS 1.5
±20％
65 0.014 4.4
LHL08□2R2M RoHS 2.2 56 0.017 4.1
LHL08□2R7M RoHS 2.7 48 0.019 3.5
LHL08□3R3M RoHS 3.3 41 0.021 3.2
LHL08□3R9M RoHS 3.9 33 0.024 3.1
LHL08□4R7M RoHS 4.7 30 0.025 3.0
LHL08□5R6M RoHS 5.6 23 0.028 2.9
LHL08□6R8M RoHS 6.8 21 0.030 2.8
LHL08□8R2M RoHS 8.2 19 0.034 2.5
LHL08□100K RoHS 10
±10％
65 17 0.041 2.4
2.52
LHL08□120K RoHS 12 16 0.044 2.3
LHL08□150K RoHS 15
50
13 0.053 2.0
LHL08□180K RoHS 18 12 0.060 1.9
LHL08□220K RoHS 22 11 0.068 1.8
LHL08□270K RoHS 27 10 0.091 1.5
LHL08□330K RoHS 33
40
8.8 0.10 1.4
LHL08□390K RoHS 39 8.4 0.12 1.3
LHL08□470K RoHS 47 8.2 0.15 1.2
LHL08□560K RoHS 56 7.9 0.17 1.1
LHL08□680K RoHS 68 35 7.0 0.20 1.0
LHL08□820K RoHS 82 6.5 0.22 0.90
LHL08□101K RoHS 100 25 5.7 0.32 0.79
0.796
LHL08□121K RoHS 120 5.2 0.36 0.70
LHL08□151K RoHS 150 20 4.7 0.41 0.64
LHL08□181K RoHS 180 35 4.2 0.66 0.60
LHL08□221K RoHS 220 3.7 0.73 0.53
LHL08□271K RoHS 270 25 3.5 0.85 0.51
LHL08□331K RoHS 330 3.2 0.97 0.44
LHL08□391K RoHS 390 20 2.9 1.1 0.41
LHL08□471K RoHS 470
25
2.4 1.3 0.38
LHL08□561K RoHS 560 2.2 1.5 0.35
LHL08□681K RoHS 680 2.0 1.8 0.32
LHL08□821K RoHS 820 30 1.6 2.3 0.30
LHL08□102J RoHS 1000
±5％
55 1.5 2.7 0.25
0.252
LHL08□122J RoHS 1200 45 1.4 3.2 0.22
LHL08□152J RoHS 1500
55
1.3 4.1 0.20
LHL08□182J RoHS 1800 1.2 4.8 0.19
LHL08□222J RoHS 2200 1.1 5.6 0.16
LHL08□272J RoHS 2700 1.0 7.5 0.15
LHL08□332J RoHS 3300 0.85 8.5 0.14
LHL08□392J RoHS 3900 0.78 9.7 0.11
LHL08□472J RoHS 4700
65
0.68 14 0.10
LHL08□562J RoHS 5600 0.62 16 0.093
LHL08□682J RoHS 6800 0.61 18 0.092
LHL08□822J RoHS 8200 0.60 20 0.084
LHL08□103J RoHS 10000
60
0.48 32 0.070
L:1kHz
Q:0.0796
LHL08□123J RoHS 12000 0.44 36 0.064
LHL08□153J RoHS 15000 0.35 62 0.051
LHL08□183J RoHS 18000 0.30 72 0.048
LHL08□223J RoHS 22000 0.28 82 0.044
LHL08□273J RoHS 27000 0.25 90 0.042
LHL08□333J RoHS 33000 0.23 100 0.040
□ Please specify the packaging code. (TB: Taping, NB: Bulk)
●LHL10
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
（min.）
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
Measuring
frequency
〔MHz〕
LHL10□3R3M RoHS 3.3
±20％50
46 0.019 4.2
7.96
LHL10□3R9M RoHS 3.9 40 0.022 4.1
LHL10□4R7M RoHS 4.7 38 0.024 4.0
LHL10□5R6M RoHS 5.6 34 0.025 3.8
LHL10□6R8M RoHS 6.8 30 0.028 3.4
LHL10□8R2M RoHS 8.2 24 0.031 3.3
LHL10□100K RoHS 10
±10％
90
19 0.034 3.2
2.52
LHL10□120K RoHS 12 16 0.038 2.8
LHL10□150K RoHS 15 12 0.042 2.6
LHL10□180K RoHS 18 9.2 0.046 2.4
LHL10□220K RoHS 22
60
8.6 0.061 2.1
LHL10□270K RoHS 27 7.1 0.069 2.0
LHL10□330K RoHS 33 6.8 0.078 1.9
LHL10□390K RoHS 39 6.7 0.085 1.8
LHL10□470K RoHS 47 50 6.2 0.093 1.7
LHL10□560K RoHS 56 5.2 0.10 1.6
To next page
116
11
leaded_i02_e-01
■ PART NUMBERS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
●LHL13
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
（min.）
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
Measuring
frequency
〔MHz〕
LHL13□100K RoHS 10
±10％
140 19 0.023 4.5
2.52
LHL13□150K RoHS 15 12 0.028 4.0
LHL13□220K RoHS 22 100 7.6 0.035 3.4
LHL13□330K RoHS 33 6.9 0.043 3.2
LHL13□470K RoHS 47 70 5.6 0.052 2.8
LHL13□680K RoHS 68
50
4.4 0.070 2.4
LHL13□101K RoHS 100 3.3 0.12 2.0
0.796
LHL13□151K RoHS 150 2.6 0.19 1.5
LHL13□221K RoHS 220 40 2.2 0.23 1.3
LHL13□331K RoHS 330
30
1.8 0.35 1.1
LHL13□471K RoHS 470 1.5 0.43 0.90
LHL13□681K RoHS 680 1.2 0.61 0.80
LHL13□102J RoHS 1000
±5％
1.0 1.2 0.60
0.252
LHL13□152J RoHS 1500
40
0.83 1.8 0.45
LHL13□222J RoHS 2200 0.70 2.2 0.40
LHL13□332J RoHS 3300 0.60 3.4 0.33
LHL13□472J RoHS 4700 0.43 4.7 0.28
LHL13□682J RoHS 6800 30 0.38 5.6 0.25
LHL13□103J RoHS 10000 70 0.30 10 0.19 L:1kHz
Q:0.0796MHz
□ Please specify the packaging code. (TB: Taping, NB: Bulk)
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
（min.）
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
Measuring
frequency
〔MHz〕
LHL10□680K RoHS 68
±10％
40
4.9 0.12 1.5 2.52
LHL10□820K RoHS 82 4.7 0.13 1.4
LHL10□101K RoHS 100 3.8 0.18 1.2
0.796
LHL10□121K RoHS 120 3.2 0.25 1.0
LHL10□151K RoHS 150 2.9 0.29 0.95
LHL10□181K RoHS 180 2.6 0.40 0.80
LHL10□221K RoHS 220 2.3 0.44 0.75
LHL10□271K RoHS 270
30
2.1 0.50 0.70
LHL10□331K RoHS 330 2.0 0.56 0.68
LHL10□391K RoHS 390 1.8 0.62 0.63
LHL10□471K RoHS 470 1.7 0.84 0.57
LHL10□561K RoHS 560 1.5 0.93 0.52
LHL10□681K RoHS 680 1.4 1.0 0.48
LHL10□821K RoHS 820 1.3 1.4 0.42
LHL10□102J RoHS 1000
±5％
50
1.2 1.8 0.41
0.252
LHL10□122J RoHS 1200 0.87 2.3 0.33
LHL10□152J RoHS 1500 0.83 2.7 0.30
LHL10□182J RoHS 1800 0.75 3.0 0.29
LHL10□222J RoHS 2200 0.70 3.9 0.25
LHL10□272J RoHS 2700 0.67 4.3 0.24
LHL10□332J RoHS 3300 0.56 5.8 0.21
LHL10□392J RoHS 3900 0.54 6.4 0.20
LHL10□472J RoHS 4700 0.49 7.1 0.19
LHL10□562J RoHS 5600 0.41 9.0 0.17
LHL10□682J RoHS 6800 0.38 10 0.16
LHL10□822J RoHS 8200 0.36 12 0.15
LHL10□103J RoHS 10000
60
0.29 19 0.12
L:1kHz
Q:0.0796
LHL10□123J RoHS 12000 0.27 21 0.11
LHL10□153J RoHS 15000 0.24 34 0.090
LHL10□183J RoHS 18000 0.21 38 0.081
LHL10□223J RoHS 22000 0.20 43 0.075
LHL10□273J RoHS 27000
40
0.15 67 0.060
LHL10□333J RoHS 33000 0.14 76 0.056
LHL10□393J RoHS 39000 0.13 84 0.053
LHL10□473J RoHS 47000 0.12 96 0.050
LHL10□563J RoHS 56000
30
0.10 170 0.036
LHL10□683J RoHS 68000 0.095 200 0.035
LHL10□823J RoHS 82000 0.088 210 0.033
LHL10□104J RoHS 100000 0.085 240 0.031 L:1kHz
Q:0.0252
LHL10□124J RoHS 120000 0.070 260 0.030
LHL10□154J RoHS 150000 0.069 300 0.028
□ Please specify the packaging code. (TB: Taping, NB: Bulk)
FERRITE PRODUCTS
117
11
leaded_i02_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
■ PART NUMBERS
●LHL16
●LHLP10
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
（min.）
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
Measuring
frequency
〔MHz〕
LHL16□470K RoHS 47
±10％
70 4.5 0.046 3.7 2.52
LHL16□680K RoHS 68 3.9 0.054 3.3
LHL16□101K RoHS 100
60
2.7 0.077 2.9
0.796
LHL16□151K RoHS 150 2.3 0.11 2.4
LHL16□221K RoHS 220 1.9 0.15 2.0
LHL16□331K RoHS 330 40 1.6 0.21 1.5
LHL16□471K RoHS 470 30 1.4 0.28 1.3
LHL16□681K RoHS 680
20
1.2 0.35 1.1
LHL16□102J RoHS 1000
±5％
0.84 0.74 0.86
0.252
LHL16□152J RoHS 1500 0.69 0.93 0.75
LHL16□222J RoHS 2200 0.56 1.4 0.60
LHL16□332J RoHS 3300 0.49 2.2 0.50
LHL16□472J RoHS 4700 0.41 2.6 0.40
LHL16□682J RoHS 6800 0.35 3.9 0.33
LHL16□103J RoHS 10000 70 0.26 7.3 0.25 L:1KHz
Q:0.0796MHz
□ Please specify the packaging code. (TB: Taping, NB: Bulk)
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Nominal Inductance
[μH]
L Measuring
frequency
Inductance
Tolerance
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
LHLP10□100M RoHS 10
2.52 ±20％
0.038 2.5
LHLP10□150M RoHS 15 0.049 2.2
LHLP10□220M RoHS 22 0.075 1.9
LHLP10□330M RoHS 33 0.094 1.7
LHLP10□470M RoHS 47 0.15 1.3
LHLP10□680M RoHS 68 0.23 1.0
LHLP10□101K RoHS 100
0.796 ±10％
0.30 0.90
LHLP10□151K RoHS 150 0.47 0.78
LHLP10□221K RoHS 220 0.70 0.63
LHLP10□331K RoHS 330 0.88 0.58
LHLP10□471K RoHS 470 1.3 0.46
LHLP10□681K RoHS 680 1.9 0.38
LHLP10□102K RoHS 1000 0.252 3.2 0.30
□ Please specify the packaging code. (TB: Taping, NB: Bulk)
●LHLP12NB
●LHLP16NB
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Nominal Inductance
[μH]
L Measuring
frequency
Inductance
Tolerance
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
LHLP12NB150M RoHS 15
2.52 ±20％
0.035 3.3
LHLP12NB220M RoHS 22 0.050 2.7
LHLP12NB330M RoHS 33 0.070 2.4
LHLP12NB470M RoHS 47 0.081 2.1
LHLP12NB680M RoHS 68 0.12 1.7
LHLP12NB101K RoHS 100
0.796 ±10％
0.16 1.6
LHLP12NB151K RoHS 150 0.24 1.3
LHLP12NB221K RoHS 220 0.38 0.95
LHLP12NB331K RoHS 330 0.46 0.89
LHLP12NB471K RoHS 470 0.69 0.74
LHLP12NB681K RoHS 680 1.1 0.58
LHLP12NB102K RoHS 1000 0.252 1.8 0.46
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Nominal Inductance
[μH]
L Measuring
frequency
Inductance
Tolerance
DC Resistance
[Ω] (max.)
Rated current
〔A〕 (max.)
LHLP16NB100M RoHS 10
1kHz
±20％
0.019 5.2
LHLP16NB150M RoHS 15 0.025 5.1
LHLP16NB220M RoHS 22 0.027 4.6
LHLP16NB330M RoHS 33 0.035 4.0
LHLP16NB470K RoHS 47
±10％
0.045 3.4
LHLP16NB680K RoHS 68 0.062 3.1
LHLP16NB101K RoHS 100 0.091 2.3
LHLP16NB151K RoHS 150 0.14 1.9
LHLP16NB221K RoHS 220 0.20 1.5
LHLP16NB331K RoHS 330 0.31 1.3
LHLP16NB471K RoHS 470 0.47 1.0
LHLP16NB681K RoHS 680 0.58 0.98
LHLP16NB102K RoHS 1000 0.94 0.74
118
11
leaded_i02_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
■
Q-vs-Frequency characteristics
■
Temperature characteristics
■ ELECTRICAL CHARACTERISTICS
■
DC Bias characteristics
LHL08
LHL10
LHL13
LHL16
LHLP10
LHLP12
LHLP16
①
②
③
④
⑤
⑥
⑦
FERRITE PRODUCTS
119
11
leaded_i02_e-01
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
11
leaded_i02_pack-P1 leaded_i02_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
①Minimum Quantity
Type (EIA) Standard quantity (pcs)
Box Bulk Taped
LHL 08 ー100 1000
LHL 10 ー50 500
LHL 13 ー25 500
LHL 16 500 ー250
LHLP10 500 ー200
LHLP12NB 300 ー ー
LHLP16NB 200 ー ー
②Bulk dimensions
◦LHL08～16
◦LHLP10～16
Type Dimensions
φD（max）H2
（max）F＊ℓ φd
LHL08 9.0 9.5 5.0±1.0 5.0±1.0 0.6±0.05
（0.354） （0.374） （0.197±0.039）（0.197±0.039）（0.024±0.002）
LHL10 11.0 14.0 5.0±1.0 5.0±1.0 0.6±0.05
（0.433） （0.551） （0.197±0.039）（0.197±0.039）（0.024±0.002）
LHL13 14.0 17.0 7.5±1.0 5.0±1.0 0.8±0.05
（0.551） （0.669） （0.295±0.039）（0.197±0.039）（0.031±0.002）
LHL16 17.0 21.0 7.5±1.0 5.0±1.0 0.8±0.05
（0.669） （0.827） （0.295±0.039）（0.197±0.039）（0.031±0.002）
*Measured at the base of the leads. Unit：mm（inch）
Type Dimensions
φD（max）H2
（max）F＊ℓ φd
LHLP10 11.0 11.0 5.0±1.0 5.0±1.0 0.6±0.05
（0.433） （0.433） （0.197±0.039）（0.197±0.039）（0.024±0.004）
LHLP12 13.0 16.0 5.0±1.0 5.0±1.0 0.6±0.05
（0.512） （0.624） （0.197±0.039）（0.197±0.039）（0.024±0.004）
LHLP16 17.0 19.0 7.5±1.0 5.0±1.0 0.8±0.05
（0.669） （0.741） （0.295±0.039）（0.197±0.039）（0.031±0.004）
*Measured at the base of the leads. Unit：mm（inch）
◦LHL08～16
◦LHLP10TB
LHL08 LHL10 LHL13 LHL16
Dφ9.0 max φ11.0 max φ14.0 max φ17.0 max
（φ0.354 max） （φ0.433 max） （φ0.551 max） （φ0.669 max）
H1
30.5 max 34.0 max 37.0 max 41.0 max
（1.20 max） （1.34 max） （1.46 max） （1.61 max）
H18.0＋2.0
－0.0 18.0＋2.0
－0.0 18.0＋2.0
－0.0 18.0＋2.0
－0.0
（0.709＋0.079
－0.000） （0.709＋0.079
－0.000） （0.709＋0.079
－0.000） （0.709＋0.079
－0.000）
H2
9.5 max 14.0 max 17.0 max 21.0 max
（0.374 max） （0.551 max） （0.669 max） （0.827 max）
LHL08 LHL10 LHL13 LHL16
P12.7±1.0 12.7±1.0 15.0±1.0 30.0±1.0
（0.500±0.039） （0.500±0.039） （0.591±0.039） （1.18±0.039）
P0
12.7±0.3※112.7±0.3※115.0±0.3※115.0±0.3※1
（0.500±0.012） （0.500±0.012） （0.591±0.012） （0.591±0.012）
P1
3.85±0.7 3.85±0.7 3.75±0.7 3.75±0.7
（0.152±0.028） （0.152±0.028） （0.148±0.028） （0.148±0.028）
P2
6.35±1.3 6.35±1.3 7.50±1.3 7.50±1.3
（0.250±0.051） （0.250±0.051） （0.295±0.051） （0.295±0.051）
F5.0＋0.8
－0.2 5.0＋0.8
－0.2 7.50＋0.8
－0.2 7.50±0.5
（0.197＋0.031
－0.008） （0.197＋0.031
－0.008） （0.295＋0.031
－0.008）（0.295±0.020）
h0.0±2.0 0.0±2.0 0.0±2.0 0.0±2.0
（0.0±0.079） （0.0±0.079） （0.0±0.079） （0.0±0.079）
W18.0＋1.0
－0.5 18.0＋1.0
－0.5 18.0＋1.0
－0.5 18.0＋1.0
－0.5
（0.709＋0.039
－0.020 ） （0.709＋0.039
－0.020 ） （0.709＋0.039
－0.020 ） （0.709＋0.039
－0.020 ）
W0
12.5 min 12.5 min 12.5 min 12.5 min
（0.492 min） （0.492 min） （0.492 min） （0.492 min）
W1
9.0±0.5 9.0±0.5 9.0±0.5 9.0±0.5
（0.354±0.020） （0.354±0.020） （0.354±0.020） （0.354±0.020）
W2
3.0 max※23.0 max※23.0 max※23.0 max※2
（0.118 max） （0.118 max） （0.118 max） （0.118 max）
D0
φ4.0±0.2 φ4.0±0.2 φ4.0±0.2 φ4.0±0.2
（φ0.158±0.008）（φ0.158±0.008）（φ0.158±0.008）（φ0.158±0.008）
φdφ0.6±0.05 φ0.6±0.05 φ0.8±0.05 φ0.8±0.05
（φ0.024±0.002）（φ0.024±0.002）（φ0.031±0.002）（φ0.031±0.002）
t0.6±0.3 0.6±0.3 0.6±0.3 0.6±0.3
（0.024±0.012） （0.024±0.012） （0.024±0.012） （0.024±0.012）
D1
φ1.8 φ1.8 φ1.8 ー
（0.071） （0.071） （0.071）
P3
6.35 6.35 7.50 ー
（0.25） （0.25） （0.25）
※1 Accumulated error for 20 pitches is 1mm.
※2 Bonding tape must not protrude from the base tape.
Unit：mm（inch）
Type Symbol Dimensions Symbol Dimensions
LHLP10
Dφ11.0 max W18.0＋1.0
－0.5
（φ0.433 max）（0.709＋0.039
－0.020 ）
H1
32.0 max W0
12.5 min
（1.26 max） （0.492 min）
H18.0＋2.0
－0.0 W1
9.0±0.5
（0.709＋0.079
－0.000）（0.354±0.020）
H2
11.0 max W2
3.0 max※2
（0.433 max） （0.118 max）
P12.7±1.0 D0
φ4.0±0.2
（0.500±0.039） （φ0.158±0.008）
P0
12.7±0.3※1
φdφ0.6±0.05
（0.500±0.012） （φ0.024±0.002）
P1
3.85±0.7 t0.6±0.3
（0.152±0.028） （0.024±0.012）
P2
6.35±1.3 D1
φ1.8
（0.250±0.051） （0.071）
F5.0＋0.8
－0.2 P3
6.35
（0.197＋0.031
－0.008）（0.25）
h0.0±2.0 Unit：mm（inch）
（0.0±0.079）
※1 Accumulated error for 20 pitches is 1mm.
※2 Bonding tape must not protrude from the base tape.
120
11
leaded_i03_e-01
■ FEATURES
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/STANDARD QUANTITY
■ APPLICATIONS
■ AVAILABLE INDUCTANCE RANGE
■ OPERATING TEMP.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ CAL45 is high current type, and has superior DC bias characteristics.
◦ Wide selection of configurations including axial leaded, formed radial
leads to meet most manufacturing needs.
◦ LHLC08/LHLC10 series which are encapsulated in a resin housing, are ra-
dial leaded inductor for high current applications.
◦ For DC/DC converter (LCD TV, PDP TV, CTV, DVD etc.)
HIGH CURRENT LEADED INDUCTORS
【CA type】
【LH type】
❶Type
CA High current axial
leaded inductor
❶Type
LH△Radial leaded
inductor
△＝Blank space
❹Lead Configurations
TB
Axial lead
(52mm lead space)/
ammo pack
VB Formed lead/
ammo pack
❹Packing Code
NB Bulk
TB
Ammo packing
❺Nominal Inductance
〔μH〕
example
1R5 1.5
120 12
※R＝decimal point
❺Nominal Inductance
〔μH〕
example
1R5 1.5
120 12
102 1000
※R＝decimal point
❻Inductance
Tolerance 〔％〕
K±10
❻Inductance Tolerance
〔％〕
J±5
K±10
M±20
❼Internal code
△△△△△
Standard product
△＝ Blank space
❼Internal code
△△△ Standard product
△＝ Blank space
❸Dimensions
(L×D) ［mm］ max
45 8.0×4.4
❸Dimensions
［mm］ max
08 9.0
10 11.0
❷Product
Specification
L△
Standard type
△＝Blank space
❷Product
Specification
LC High current type
C A L △4 5 T B 1 0 0 K ○○○○○
❶❷❸❹ ❺❻ ❼
L H △L C 0 8 T B 1 0 1 K ○○○
❶ ❷❸❹ ❺❻❼
Type Fig. Dimensions ［mm］（inch）Taped Standard Quantity (pcs)
LφDφd Straight Formed Bulk Taped
CAL45 8.0max
（0.315max）
4.4max
（0.173max）
0.65±0.05
（0.026±0.002）—
Axial lead 2000
Formed lead 1500
Unit：mm （inch）
TB
Type Fig. D H2ℓFφdStandard Quantity (pcs)
Bulk Taped
LHLC08 9.0max
（0.354max）
9.5max
（0.374max）
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
0.6±0.05
（0.024±0.002）100 1000
LHLC10 11.0max
（0.433max）
14.0max
（0.551max）
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
0.6±0.05
（0.024±0.002）50 500
Unit：mm（inch）
【CA type】
【LH type】
5.0mm（0.197）
VB
Range Type CAL45 LHLC08 LHLC10
0.1μRdc
max[Ω]
Imax[A] Rdc
max[Ω]
Imax[A] Rdc
max[Ω]
Imax[A]
1.0μ0.036 1.0μ3.3 0.013 1.0μ5.4
10μ0.14 1.7 0.041 2.9 0.034
3.3μ
3.6
100μ1.2 0.59 0.32 1.0 0.18 1.5
1.0m 13.2 0.17 2.7 0.35 1.8 0.48
10m 32.0 0.11 19.0 0.14
100m
10m 33m 240.0 0.038
150m
Inductance ［H］
WAV E
◦ ー25℃～105℃（Including self-generated heat）
FERRITE PRODUCTS
121
11
leaded_i03_e-01
■ PART NUMBERS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
●CAL45
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(refarence)
Self-resonant
frequency
[MHz]
(refarence)
Measuring
frequency
[MHz]
DC Resistance
[Ω]
(max.)
Rated current ※）
[mA] (max.)
Saturation current
Idc1
Temperature rise current
Idc2
CAL 45 ○ 1R0K RoHS 1.0
±10%
30
350
7.96
0.036 5600 3300
CAL 45 ○ 1R2K RoHS 1.2 300 0.039 5000 3200
CAL 45 ○ 1R5K RoHS 1.5 300 0.041 4400 3000
CAL 45 ○ 1R8K RoHS 1.8 200 0.048 4100 2800
CAL 45 ○ 2R2K RoHS 2.2 200 0.054 3900 2700
CAL 45 ○ 2R7K RoHS 2.7 70 0.058 3500 2500
CAL 45 ○ 3R3K RoHS 3.3 70 0.066 3100 2400
CAL 45 ○ 3R9K RoHS 3.9 40 0.072 3000 2300
CAL 45 ○ 4R7K RoHS 4.7 40 0.079 2800 2200
CAL 45 ○ 5R6K RoHS 5.6 35 0.089 2500 2100
CAL 45 ○ 6R8K RoHS 6.8 35 0.097 2200 2000
CAL 45 ○ 8R2K RoHS 8.2 30 0.110 2000 1900
CAL 45 ○ 100K RoHS 10
40
25
2.52
0.14 1700 1800
CAL 45 ○ 120K RoHS 12 25 0.17 1600 1450
CAL 45 ○ 150K RoHS 15 25 0.19 1400 1430
CAL 45 ○ 180K RoHS 18 20 0.24 1250 1300
CAL 45 ○ 220K RoHS 22 20 0.28 1200 1220
CAL 45 ○ 270K RoHS 27 17 0.33 1100 1130
CAL 45 ○ 330K RoHS 33
30
15 0.37 1000 1080
CAL 45 ○ 390K RoHS 39 13 0.47 920 900
CAL 45 ○ 470K RoHS 47 13 0.52 890 870
CAL 45 ○ 560K RoHS 56 11 0.75 790 710
CAL 45 ○ 680K RoHS 68 10 0.78 700 700
CAL 45 ○ 820K RoHS 82 9 0.92 620 640
CAL 45 ○ 101K RoHS 100 40 9
0.796
1.2 590 630
CAL 45 ○ 121K RoHS 120 50 7 1.6 550 490
CAL 45 ○ 151K RoHS 150 60 7 1.8 490 470
CAL 45 ○ 181K RoHS 180 5 2.3 420 450
CAL 45 ○ 221K RoHS 220 80 5 2.9 370 425
CAL 45 ○ 271K RoHS 270
70
5 3.4 350 355
CAL 45 ○ 331K RoHS 330 4.5 3.6 320 330
CAL 45 ○ 391K RoHS 390 4 4.9 290 280
CAL 45 ○ 471K RoHS 470
80
46.3 270 240
CAL 45 ○ 561K RoHS 560 3 7.0 250 240
CAL 45 ○ 681K RoHS 680 3 7.8 240 220
CAL 45 ○ 821K RoHS 820 2.5 11.0 220 210
CAL 45 ○ 102K RoHS 1000 2.5
0.252
13.2 190 170
CAL 45 ○ 122K RoHS 1200 2 17 170 150
CAL 45 ○ 152K RoHS 1500 2 22 150 140
CAL 45 ○ 182K RoHS 1800 1.5 27 140 120
CAL 45 ○ 222K RoHS 2200 1.5 36 130 110
CAL 45 ○ 272K RoHS 2700
70
1.2 45 110 90
CAL 45 ○ 332K RoHS 3300 1.2 65 100 75
CAL 45 ○ 392K RoHS 3900 1 69 95 70
CAL 45 ○ 472K RoHS 4700 1 80 90 65
CAL 45 ○ 562K RoHS 5600 1 90 90 60
CAL 45 ○ 682K RoHS 6800 1 100 80 60
CAL 45 ○ 822K RoHS 8200 0.7 125 75 50
CAL 45 ○ 103K RoHS 10000 30 0.6 0.0796 155 65 45
○ Please specify the Lead configuration code.
※）The saturation current value (Idc1) is the DC current value having inductance decrease down to 10%. (at 20℃)
※）The temperature rise current value (Idc2) is the DC current value having temperature increase up to 40℃. (at 20℃)
※）The rated current is the DC current value that satisfies both of current value saturation current value and temperature rise current value.
●LHLC08
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω]
(max.)
Rated current
〔A〕
(max.)
Measuring
frequency
〔MHz〕
LH LC08□□1R0N RoHS 1.0 ±30％
40
76 0.013 5.4
7.96
LH LC08□□1R5M RoHS 1.5
±20％
65 0.014 5.2
LH LC08□□2R2M RoHS 2.2 56 0.017 4.8
LH LC08□□2R7M RoHS 2.7 48 0.019 4.2
LH LC08□□3R3M RoHS 3.3 41 0.021 3.8
LH LC08□□3R9M RoHS 3.9 33 0.024 3.7
LH LC08□□4R7M RoHS 4.7 30 0.025 3.6
LH LC08□□5R6M RoHS 5.6 23 0.028 3.5
LH LC08□□6R8M RoHS 6.8 21 0.030 3.4
LH LC08□□8R2M RoHS 8.2 19 0.034 3.0
LH LC08□□100K RoHS 10
±10％
65 17 0.041 2.9
2.52
LH LC08□□120K RoHS 12 16 0.044 2.8
LH LC08□□150K RoHS 15
50
13 0.053 2.6
LH LC08□□180K RoHS 18 12 0.060 2.4
LH LC08□□220K RoHS 22 11 0.068 2.3
To next page
122
11
leaded_i03_e-01
■ PART NUMBERS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
●LHLC10
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω]
(max.)
Rated current
〔A〕
(max.)
Measuring
frequency
〔MHz〕
LH LC10□□3R3M RoHS 3.3
±20％50
46 0.019 5.0
7.96
LH LC10□□3R9M RoHS 3.9 40 0.022 4.8
LH LC10□□4R7M RoHS 4.7 38 0.024 4.7
LH LC10□□5R6M RoHS 5.6 34 0.025 4.5
LH LC10□□6R8M RoHS 6.8 30 0.028 4.1
LH LC10□□8R2M RoHS 8.2 24 0.031 3.9
LH LC10□□100K RoHS 10
±10％
90
19 0.034 3.6
2.52
LH LC10□□120K RoHS 12 16 0.038 3.4
LH LC10□□150K RoHS 15 12 0.042 3.2
LH LC10□□180K RoHS 18 9.2 0.046 3.0
LH LC10□□220K RoHS 22
60
8.6 0.061 2.8
LH LC10□□270K RoHS 27 7.1 0.069 2.7
LH LC10□□330K RoHS 33 6.8 0.078 2.6
LH LC10□□390K RoHS 39 6.7 0.085 2.4
LH LC10□□470K RoHS 47 50 6.2 0.093 2.3
LH LC10□□560K RoHS 56 5.2 0.10 2.1
LH LC10□□680K RoHS 68
40
4.6 0.12 2.0
LH LC10□□820K RoHS 82 4.7 0.13 1.8
LH LC10□□101K RoHS 100 3.8 0.18 1.5
0.796
LH LC10□□121K RoHS 120 3.2 0.25 1.3
LH LC10□□151K RoHS 150 2.9 0.29 1.2
LH LC10□□181K RoHS 180 2.6 0.40 1.0
LH LC10□□221K RoHS 220 2.3 0.44 0.95
LH LC10□□271K RoHS 270
±10％30
2.1 0.50 0.90
0.796
LH LC10□□331K RoHS 330 2.0 0.56 0.86
LH LC10□□391K RoHS 390 1.8 0.62 0.75
LH LC10□□471K RoHS 470 1.7 0.84 0.65
LH LC10□□561K RoHS 560 1.5 0.93 0.61
LH LC10□□681K RoHS 680 1.4 1.0 0.57
LH LC10□□821K RoHS 820 1.3 1.4 0.50
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω]
(max.)
Rated current
〔A〕
(max.)
Measuring
frequency
〔MHz〕
LH LC08□□270K RoHS 27
±10％
50 10 0.091 2.0
2.52
LH LC08□□330K RoHS 33
40
8.8 0.10 1.9
LH LC08□□390K RoHS 39 8.4 0.12 1.7
LH LC08□□470K RoHS 47 8.2 0.15 1.5
LH LC08□□560K RoHS 56 7.9 0.17 1.4
LH LC08□□680K RoHS 68 35 7.0 0.20 1.3
LH LC08□□820K RoHS 82 6.5 0.22 1.2
LH LC08□□101K RoHS 100 25 5.7 0.32 1.0
0.796
LH LC08□□121K RoHS 120 5.2 0.36 0.96
LH LC08□□151K RoHS 150 20 4.7 0.41 0.88
LH LC08□□181K RoHS 180 35 4.2 0.66 0.71
LH LC08□□221K RoHS 220 3.7 0.73 0.66
LH LC08□□271K RoHS 270 25 3.5 0.85 0.63
LH LC08□□331K RoHS 330 3.2 0.97 0.59
LH LC08□□391K RoHS 390 20 2.9 1.1 0.55
LH LC08□□471K RoHS 470
25
2.4 1.3 0.49
LH LC08□□561K RoHS 560 2.2 1.5 0.47
LH LC08□□681K RoHS 680 2.0 1.8 0.44
LH LC08□□821K RoHS 820 30 1.6 2.3 0.38
LH LC08□□102J RoHS 1000
±5％
55 1.5 2.7 0.35
0.252
LH LC08□□122J RoHS 1200 45 1.4 3.2 0.31
LH LC08□□152J RoHS 1500
55
1.3 4.1 0.29
LH LC08□□182J RoHS 1800 1.2 4.8 0.26
LH LC08□□222J RoHS 2200 1.1 5.6 0.23
LH LC08□□272J RoHS 2700 1.0 7.5 0.21
LH LC08□□332J RoHS 3300 0.85 8.5 0.19
LH LC08□□392J RoHS 3900 0.78 9.7 0.18
LH LC08□□472J RoHS 4700
65
0.68 14 0.16
LH LC08□□562J RoHS 5600 0.62 16 0.15
LH LC08□□682J RoHS 6800 0.61 18 0.14
LH LC08□□822J RoHS 8200 0.60 20 0.13
LH LC08□□103J RoHS 10000
60
0.48 32 0.11
L:1kHz
Q:0.0796
LH LC08□□123J RoHS 12000 0.44 36 0.084
LH LC08□□153J RoHS 15000 0.35 62 0.068
LH LC08□□183J RoHS 18000 0.30 72 0.066
LH LC08□□223J RoHS 22000 0.28 82 0.057
LH LC08□□273J RoHS 27000 0.25 90 0.054
LH LC08□□333J RoHS 33000 0.23 100 0.053
□ Please specify the packaging code. (TB: Taping, NB: Bulk)
To next page
FERRITE PRODUCTS
123
11
leaded_i03_e-01
■ PART NUMBERS
■ ELECTRICAL CHARACTERISTICS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Inductance
[μH]
Inductance
Tolerance
Q
(min.)
Self-resonant
frequency
〔MHz〕 (min.)
DC Resistance
[Ω]
(max.)
Rated current
〔A〕
(max.)
Measuring
frequency
〔MHz〕
LH LC10□□102J RoHS 1000
±5％
50
1.2 1.8 0.48
0.252
LH LC10□□122J RoHS 1200 0.87 2.3 0.40
LH LC10□□152J RoHS 1500 0.83 2.7 0.37
LH LC10□□182J RoHS 1800 0.75 3.0 0.36
LH LC10□□222J RoHS 2200 0.70 3.9 0.32
LH LC10□□272J RoHS 2700 0.67 4.3 0.30
LH LC10□□332J RoHS 3300 0.56 5.8 0.26
LH LC10□□392J RoHS 3900 0.54 6.4 0.25
LH LC10□□472J RoHS 4700 0.49 7.1 0.24
LH LC10□□562J RoHS 5600 0.41 9.0 0.21
LH LC10□□682J RoHS 6800 0.38 10 0.20
LH LC10□□822J RoHS 8200 0.36 12 0.18
LH LC10□□103J RoHS 10000
60
0.29 19 0.14
L:1kHz
Q:0.0796
LH LC10□□123J RoHS 12000 0.27 21 0.13
LH LC10□□153J RoHS 15000 0.24 34 0.11
LH LC10□□183J RoHS 18000 0.21 38 0.10
LH LC10□□223J RoHS 22000 0.20 43 0.095
LH LC10□□273J RoHS 27000
40
0.15 67 0.076
LH LC10□□333J RoHS 33000 0.14 76 0.068
LH LC10□□393J RoHS 39000 0.13 84 0.065
LH LC10□□473J RoHS 47000 0.12 96 0.061
LH LC10□□563J RoHS 56000
30
0.10 170 0.045
LH LC10□□683J RoHS 68000 0.095 200 0.043
LH LC10□□823J RoHS 82000 0.088 210 0.041
LH LC10□□104J RoHS 100000 0.085 240 0.038 L:1kHz
Q:0.0252
LH LC10□□124J RoHS 120000 0.070 260 0.037
LH LC10□□154J RoHS 150000 0.069 300 0.035
□ Please specify the packaging code. (TB: Taping, NB: Bulk)
LHLC10
1000000
100000
10000
1000
100
10
1
0.01 0.1 1 10
154J
104J
473J
223J
103J
472J
222J
102J
471K
221K
101K
470K
220K
100K
3R3M
1000
10000
100000
100
10
0.01 0.1 110
1
0.1
CAL45
CAL45TB102K
CAL45TB103K
CAL45TB101K
CAL45TB100K
CAL45TB1R0K
LHLC08
100000
10000
1000
100
10
1
0.1
0.01 0.1 1 10
333
223
103
472
222
102
471
221
101
470K
220
100
4R7
2R2
1R0
（Measured by HP4285A）
■
DC Bias characteristics
11
leaded_i03_pack-P1 leaded_i03_pack_e-01
■ PACKAGING
Type Symbol Dimensions Symbol Dimensions
CAL 45
Dφ4.4max W 18.0＋1.0
ー0.5
（0.709＋0.039
ー0.020 ）
H2
14.0max
（0.551max）W0
12.5min
（0.492min）
H0
16.0±1.0
（0.630±0.039）W1
9.0＋0.75
ー0.5
（0.354＋0.030
ー0.020 ）
P12.7±1.0
（0.500±0.039）W2
3.0max ※2
（0.118max）
P0
12.7±0.3 ※1
（0.500±0.012）ℓ2.0max
（0.079max）
P1
3.85±0.7
（0.152±0.028）D0
φ4.0±0.2
（φ0.157±0.008）
P2
6.35±1.3
（0.250±0.051）φdφ0.65±0.05
（φ0.026±0.002）
F5.0±1.0
（0.197±0.039）L11.0max
（0.433max）
△h0.0±2.0
（0.0±0.079）t0.9max
（0.035max）
Unit：mm（inch）
※1 Accumulated error for 20 pitches is ± 1mm.
※2 Bonding tape must not protrude from the base tape.
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦CAL 45
①Minimum Quantity
Type (EIA) Standard quantity (pcs)
Bulk Taped
CAL45 —Axial lead 2000
Formed lead 1500
LHLC08 100 1000
LHLC10 50 500
②Taping dimensions
TB（a：52mm lead space）
（2.05 inches）
Type
Dimensions Minimum
insertion
pitch
φD L a b |L1-L2|φd
CAL45 4.4max
（0.173max）
8.0max
（0.315max）
52＋2
ー1
（2.05＋0.079
ー0.039 ）
1.2max
（0.047max）
1.0max
（0.039max）
0.65±0.05
（0.026±0.002）
10.0
（0.394）
Unit：mm（inch）
③Bulk dimensions
◦CAL 45VB
Type
Dimensions
φD
(max)H2 (max) F＊ ℓ φd
LHLC08
9.0
（0.354）
9.5
（0.374）
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
0.6±0.05
（0.024±0.002）
LHLC10
11.0
（0.433）
14.0
（0.551）
5.0±1.0
（0.197±0.039）
5.0±1.0
（0.197±0.039）
0.6±0.05
（0.024±0.002）
*Measured at the base of the leads. Unit：mm（inch）
◦LHLC08, LHLC10
LHLC08 LHLC10
Dφ9.0max
(φ0.354max）φ11.0max
（φ0433max）
H1
30.5max
（1.20max）34.0max
（1.34max）
H18.0＋2.0
ー0.0
（0.709
＋0.079
ー0.000
）
18.0＋2.0
ー0.0
（0.709
＋0.079
ー0.000
）
H2
9.5max
（0.374max）14.0max
（0.551max）
P12.7±1.0
（0.500±0.039）12.7±1.0
（0.500±0.039）
P0
12.7±0.3※1
（0.500±0.012）12.7±0.3※1
（0.500±0.012）
P1
3.85±0.7
（0.152±0.028）3.85±0.7
（0.152±0.028）
P2
6.35±1.3
（0.250±0.051）6.35±1.3
（0.250±0.051）
F5.0＋0.8
ー0.2
（0.197
＋0.031
ー0.008
）5.0＋0.8
ー0.2
（0.197
＋0.031
ー0.008
）
h0.0±2.0
（0.0±0.079）0.0±2.0
（0.0±0.079）
W18.0＋1.0
ー0.5
（0.709
＋0.039
ー0.020
）
18.0＋1.0
ー0.5
（0.709
＋0.039
ー0.020
）
W0
12.5min
（0.492min）12.5min
（0.492min）
W1
9.0±0.5
（0.354±0.020）
9.0±0.5
（0.354±0.020）
W2
3.0max※2
（0.118max）3.0max※2
（0.118max）
D0
φ4.0±0.2
（φ0.158±0.008）φ4.0±0.2
（φ0.158±0.008）
φdφ0.6±0.05
（φ0.024±0.002）φ0.6±0.05
（φ0.024±0.002）
t0.6±0.3
（0.024±0.012）0.6±0.3
（0.024±0.012）
D1
φ1.8
（0.071）φ1.8
（0.071）
P3
6.35
（0.25）6.35
（0.25）
※1 Accumulated error for 20 pitches is 1mm. Unit：mm（inch）
※2 Bonding tape must not protrude from the base tape.
124
11
leaded_i04_e-01
■ FEATURES
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/STANDARD QUANTITY
■ APPLICATIONS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦ Use of high loss ferrite material.
◦ Easy mounting on PC boards.
◦
Available in a wide range of values and configurations to suit most applications.
◦ Waveform correction of digital signals from digital equipment and ab-
sorption of high-frequency noise from data lines.
LEADED FERRITE BEADS INDUCTORS
❶Type
FB Ferrite Beads
❹Material code
HA Refer to impedance
curves for material
difference
VA
❺Nominal Impedance
example
850 85
121 120
Excluding 03Type
❻Lead configuration 〔mm〕
AB Straight lead (26mm lead space) / ammo SA Straight lead (FBR05 type) / ammo
BB Straight lead (52mm lead space) / ammo SB Straight lead (FBR07 type) / ammo
KD Formed lead (10mm pitch) / bulk TB Straight lead (FBR07 type) / ammo
KE Formed lead (12.5mm pitch) / bulk UB Radial lead formed / ammo
KF Formed lead / bulk (15.0mm pitch) / bulk US Formed lead (crimped) / bulk
NA Lead (2.5mm pitch)/bulk (FBR) VB Dual side lead formed (crimped) / ammo
Straight lead / bulk (FBA) VS Formed lead / bulk
NB Formed lead (crimped) / bulk
❼Internal code
ー00 Standard Products
❸Core Dimensions
〔mm〕
03 φ2.5
04 φ3.5
05 5.0
06 6.0
07 7.5
❷Configuration
A Axial lead
RRadial lead
F B A 0 4 H A 4 5 0 B B ○○○
❶ ❷ ❸ ❹ ❺ ❻ ❼
Type
Configurations Dimensions Standard Quantity (pcs)
Taping Bulk D L Type
Lead
Configuration
Bulk
Taped
Ammo
Straight Formed Straight Formed
FBA
03H A450 □- 00
0 3V A 4 50 □- 0 0
2.5±0.2 4.5±0.3 FBA03
NA, KD, US 1000 ー
KE, KF, VS 500 ー
(0.098±0.008) (0.177±0.012)
AB, BB ー2000
UB, VB ー3000
04H A 450 □- 0 0
0 4V A 4 50 □- 0 0
3.5±0.2 4.5±0.3
FBA04
NA, KD, US 1000 ー
(0.138±0.008) (0.177±0.012)
KE, KF, VS 500 ー
04H A 6 00 □- 0 0
0 4V A 6 0 0 □- 0 0
3.5±0.2 6.0
＋0.5
－0
(0.138±0.008) (0.236
＋0.020
－0
)
AB, BB ー1000
04H A 90 0 □- 00
0 4V A 9 0 0 □- 0 0
3.5±0.2 9.0±0.5
UB, VB ー3000
(0.138±0.008)
(0.354±0.020)
FBR
0 5 V A 12 1 □- 0 0 ー ー 5.0 max. 7.5 FBR05
NA 1000 ー
(0.197 max.) (0.295)
SA ー2000
06H A850N A-00
06V A85 0N A - 00
ーーー 6.0±0.5
5.0
FBR06 NA 1000 ー
(0.197)
06H A121N A - 00
0 6V A121N A - 0 0
(0.236±0.020)
7.0
(0.276)
07H A850 □- 0 0
0 7 V A 85 0 □- 0 0
ー ー 7.5±0.5
5.5
FBR07
NB 1000 ー
(0.217)
07H A12 1 □- 0 0
0 7 V A1 21 □- 0 0
(0.295±0.020)
7.5 SB ー2000
(0.295)
□Please specify the lead configuration code.
Note: Lead diameter (φd) shall fall within a range of 0.65mm±0.05mm, FBR05, and FBR07 types however, will have a lead diameter (φd) range of 0.6mm±0.05mm.
Unit：mm （inch）
P: 12.7 (0.500)
P: 12.7 (0.500)
P: 12.7 (0.500)
P: 12.7 (0.500)
P: 12.7 (0.500)
F: 2.5 (0.098)
F: 2.5 (0.098)
F: 5.0 (0.197)
F: 12.5, 15 (0.492, 0.591)
F: 10, 12.5, 15 (0.39, 0.492, 0.591)
F: 10, 12.5, 15 (0.39, 0.492, 0.591)
F: 5.0 (0.197)
F: 10, 12.5, 15 (0.39, 0.492, 0.591)
F: 5.0 (0.197)
WAV E
■ OPERATING TEMP.
◦ ー25℃～85℃
FERRITE PRODUCTS
125
11
leaded_i04_e-01
■ PART NUMBERS
■ ELECTRICAL CHARACTERISTICS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Ordering code
EHS (
Environmental
Hazardous
Substances
)
Impedance
[Ω] min.
Measuring frequency [MHz] Rated Current [A] max.
Material Material
HA VA HA VA
FBA
03 △ 450 □ ー00 RoHS 35.0 50 100 7.0 7.0
04 △ 450 □ ー00 RoHS 45.0 50 100 7.0 7.0
04 △ 600 □ ー00 RoHS 60.0 50 100 7.0 7.0
04 △ 900 □ ー00 RoHS 90.0 50 100 7.0 7.0
FBR
05 VA 121 □ ー00 RoHS 120.0 ー100 ー7.0
06 △ 850 NA ー00 RoHS 85.0 50 100 7.0 7.0
06 △ 121 NA ー00 RoHS 120.0 50 100 7.0 7.0
07 △ 850 □ ー00 RoHS 85.0 50 100 7.0 7.0
07 △ 121 □ ー00 RoHS 120.0 50 100 7.0 7.0
△Please specify material codes (HA,VA) and □ lead configuration code.
※DC Resistance : 0.01Ω max., Insulation resistance : 1.0MΩ min.
（Measured by HP4191A）
■
IMPEDANCE-vs-FREQUENCY CHARACTERISTICS
11
leaded_i04_pack-P1 leaded_i04_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Axial lead (FBA)
◦NA
◦US
①Minimum Quantity
Type Lead Configuration
Standard quantity [pcs]
Bulk Taped
Ammo
FBA03
NA, KD, US 1000 ー
KE, KF, VS 500 ー
AB, BB ー2000
UB, VB ー3000
FBA04
NA, KD, US 1000 ー
KE, KF, VS 500 ー
AB, BB ー1000
VB, UB ー3000
Type Lead Configuration
Standard quantity [pcs]
Bulk Taped
Ammo
FBR05 NA 1000 ー
SA ー2000
FBR06 NA 1000 ー
FBR07 NB 1000 ー
SB ー2000
②Bulk dimensions
Type Dimensions
φD L1 L2 φdℓ
FBA03□450 2.5±0.2 4.5±0.3 6.5 max.
0.65±0.05 18 min.
(0.098±0.008)
(0.177±0.012)
(0.256 max.)
FBA04□450 3.5±0.2 4.5±0.3 6.5 max.
(0.138±0.008) (0.177±0.012)
(0.256 max.)
FBA04□600 3.5±0.2 6.0＋0.5
ー08.5 max.
(0.026±0.002)
(0.709 min.)
(0.138±0.008) (0.236
＋0.020
ー0
)
(0.335 max.)
FBA04□900 3.5±0.2 9.0±0.5 11.0 max.
(0.138±0.008)
(0.354±0.020)
(0.433 max.)
Unit : mm (inch)
Type Dimensions
φD A a F φd
FBA03□450 2.5±0.2 4.5±0.3 12.5 max. 5.0±1.0 0.65±0.05
(0.098±0.008)
(0.177±0.012)
(0.492 max.)
(0.197±0.039)
(0.026±0.002)
FBA04□450 3.5±0.2 4.5±0.3 12.5 max. 5.0±1.0 0.65±0.05
(0.138±0.008) (0.177±0.012)
(0.492 max.)
(0.197±0.039)
(0.026±0.002)
FBA04□600 3.5±0.2 6.0＋0.5
ー012.5 max. 5.0±1.0 0.65±0.05
(0.138±0.008) (0.236
＋0.020
ー0
)
(0.492 max.)
(0.197±0.039)
(0.026±0.002)
FBA04□900 3.5±0.2 9.0±0.5 16.0 max. 5.0±1.0 0.65±0.05
(0.138±0.008)
(0.354±0.020)
(0.630 max.)
(0.197±0.039)
(0.026±0.002)
Unit : mm (inch)
Type
Lead
Symbol
Dimensions
φD F L1 φdℓ
FBA03□450
KD
2.5±0.2 10.0±1.0 4.5±0.3
0.65±0.05
7.0±2.0
(0.098±0.008) (0.394±0.040)
(0.177±0.012)
(0.276±0.079)
FBA04□450
3.5±0.2 10.0±1.0 4.5±0.3 7.5±2.0
(0.138±0.008) (0.394±0.040)
(0.177±0.012)
(0.026±0.020) (0.295±0.079)
FBA04□600
3.5±0.2 10.0±1.0 6.0＋0.5
ー07.5±2.0
(0.138±0.008) (0.394±0.040)
(0.236
＋0.020
ー0
)
(0.295±0.079)
FBA03□450
KE
2.5±0.2 12.5±1.0 4.5±0.3
0.65±0.05
7.0±2.0
(0.098±0.008) (0.492±0.004)
(0.177±0.012)
(0.276±0.079)
FBA04□450
3.5±0.2 12.5±1.0 4.5±0.3 7.5±2.0
(0.138±0.008) (0.492±0.004)
(0.177±0.012)
(0.295±0.079)
FBA04□600
3.5±0.2 12.5±1.0 6.0＋0.5
ー0
(0.026±0.020)
7.5±2.0
(0.138±0.008) (0.492±0.004)
(0.236
＋0.020
ー0
)
(0.295±0.079)
FBA04□900
3.5±0.2 12.5±1.0 9.0±0.5 7.5±2.0
(0.138±0.008) (0.492±0.004) (0.354±0.020) (0.295±0.079)
FBA03□450
KF
2.5±0.2 15.0±1.0 4.5±0.3
0.65±0.05
7.0±2.0
(0.098±0.008) (0.591±0.004)
(0.177±0.012)
(0.276±0.079)
FBA04□450
3.5±0.2 15.0±1.0 4.5±0.3 7.5±2.0
(0.138±0.008) (0.591±0.004)
(0.177±0.012)
(0.295±0.079)
FBA04□600
3.5±0.2 15.0±1.0 6.0＋0.5
ー0
(0.026±0.020)
7.5±2.0
(0.138±0.008) (0.591±0.004)
(0.236
＋0.020
ー0
)
(0.295±0.079)
FBA04□900
3.5±0.2 15.0±1.0 9.0±0.53 7.5±2.0
(0.138±0.008) (0.591±0.004) (0.354±0.020) (0.295±0.079)
Unit : mm (inch)
Type Dimensions
φD A a F φd
FBA03□450 2.5±0.2 4.5±0.3 9.0 max.
5.0±1.0 0.65±0.05
(0.098±0.008)
(0.177±0.012)
(0.354 max.)
FBA04□450 3.5±0.2 4.5±0.3 9.0 max.
(0.197±0.039)
(0.026±0.002)
(0.138±0.008) (0.177±0.012)
(0.354 max.)
Unit : mm (inch)
◦KD/KE/KF
◦VS
◦Axial lead (FBA)
◦Radial lead (FBR)
※
※5±1 for 900 type only
Type Dimensions
D L1 φdℓW F
FBR05VA121
5.0 max. 9.0 max. 0.65±0.05 10.0＋3
ー52.5 max. 2.5±1.0
(0.197 max.)
(0.354 max.)
(0.026±0.002)
(0.394
＋0.118
ー0.197
)
(0.098 max.)
(0.098±0.039)
FBR06□850
6.0±0.5 7.0 max. 0.65±0.05 10.0＋3
ー53.0±0.5 2.5±1.0
(0.236±0.020)
(0.276 max.)
(0.026±0.002)
(0.394
＋0.118
ー0.197
)
(0.118±0.020) (0.098±0.039)
FBR06□121
6.0±0.5 9.0 max. 0.65±0.05 10.0＋3
ー53.0±0.5 2.5±1.0
(0.236±0.020)
(0.354 max.)
(0.026±0.002)
(0.394
＋0.118
ー0.197
)
(0.118±0.020) (0.098±0.039)
Unit : mm (inch)
Radial lead (FBR)
◦NA
11
leaded_i04_pack-P2
leaded_i04_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
Type Dimensions
D L1 φdℓW F
FBR07□850
7.5±0.5 7.0 max. 0.6±0.05 5.0＋1
ー22.5 max. 5.0＋1
ー0.5
(0.295±0.020)
(0.276 max.)
(0.024±0.002)
(0.197
＋0.039
ー0.079
)
(0.098 max.)
(0.197
＋0.039
ー0.020
)
FBR07□121
7.5±0.5 9.0 max. 0.6±0.05 5.0＋1
ー22.5 max. 5.0＋1
ー0.5
(0.295±0.020)
(0.354 max.)
(0.024±0.002)
(0.197
＋0.039
ー0.079
)
(0.098 max.)
(0.197
＋0.039
ー0.020
)
Unit : mm (inch)
◦NB
◦AB (a : 26mm) (1.02inch lead space)
③Taping Dimensions
Type Dimensions
Minimum
insertion
pitch
φD L a b |L1-L2|φd
FBA03 2.5±0.2 4.5±0.3 26.0＋1.5
ー00.8max 1.0 max
0.65±0.05
10.0
(0.098±0.008)
(0.177±0.012)
(1.02
＋0.059
ー0
)(0.031max) (0.039 max)
(0.026±0.002)
(0.394)
FBA04
□450
3.5±0.2
（0.138±0.008）
4.5±0.3
26.0＋1.5
ー0
（1.02
＋0.059
ー0
）
0.8max
（0.031max）
1.0 max
（0.039 max）
0.65±0.05
（0.026±0.002）
10.0
（0.394）
（0.177±0.012）
FBA04
□600
6.0＋0.5
ー0
（0.236
＋0.020
ー0
）
FBA04
□900
9.0±0.5
（0.354±0.020）
Unit : mm (inch)
Type Symbol Dimensions Symbol Dimensions
FBR05
A9.0 max. W18.0＋1.0
－0.5
(0.354 max.) (0.709＋0.039
－0.020 )
T2.5 max. W0
12.5 min.
(0.098 max.) (0.492 min.)
D5.0 max. W1
9.0＋0.75
－0.5
(0.197 max.) (0.354＋0.039
－0.020 )
H18.0＋2.0
ー0W2
3.0 max. ※2
(0.709＋0.079
ー0)(0.118 max.)
P12.7±1.0 ℓ1.0 max.
(0.500±0.039) (0.039 max.)
P0
12.7±0.3 ※1
φD0
4.0±0.3
(0.500±0.039) (0.157±0.012)
P1
5.1±0.7 φd0.65±0.05
(0.201±0.028) (0.026±0.002)
P2
6.35±1.3 L11.0 max.
(0.250±0.051) (0.433 max.)
F2.5＋1.0
ー0.5 t0.7±0.2
(0.098＋0.039
ー0.020 )(0.028±0.008)
△h0.0±2.0 Unit : mm(inch)
(0.0±0.079)
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
121:
◦BB (a : 52mm) (2.05inches lead space)
Type
Dimensions
Minimum
insertion
pitch
φD L a b |L1-L2|φd
FBA03 2.5±0.2 4.5±0.3 52.0＋2
ー11.2 max 1.0 max
0.65±0.05
10.0
(0.098±0.008)
(0.177±0.012)
(2.05
＋0.079
ー0.039
)(0.047 max) (0.039 max)
(0.026±0.002)
(0.394)
FBA04
□450
3.5±0.2
（0.138±0.008）
4.5±0.3
52.0＋2
ー1
（2.05
＋0.079
ー0.039
）
1.2max
（0.047max）
1.0 max
（0.039 max）
0.65±0.05
（0.026±0.002）
10.0
（0.394）
（0.177±0.012）
FBA04
□600
6.0＋0.5
ー0
（0.236
＋0.020
ー0
）
FBA04
□900
9.0±0.5
（0.354±0.020）
Unit : mm (inch)
◦SA (F : 2.5mm pitch) (0.098 inches)
11
leaded_i04_pack-P3 leaded_i04_pack_e-01
■ PACKAGING
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
◦UB
Type Symbol Dimensions Symbol Dimensions
FBA03□450
FBA04□450
A4.5±0.3 △h0.0±2.0
(0.177±0.012) (0.0±0.079)
A1
9.0 max. W18.0＋1.0
－0.5
(0.354 max.) (0.709＋0.039
－0.020 )
φD
2.7 max. W0
12.5 min.
(0.106 max.) (0.492 min.)
3.7 max. W1
9.0＋0.75
－0.5
(0.146 max.) (0.354＋0.039
－0.020 )
H20.0＋0.5
ー1.0 W2
3.0 max. ※2
(0.787＋0.020
ー0.039)(0.118 max.)
P12.7±1.0 ℓ1.0 max.
(0.500±0.039) (0.039 max.)
P0
12.7±0.3 ※1
φD0
4.0±0.3
(0.500±0.012) (0.157±0.012)
P1
3.85±0.8 φd0.65±0.05
(0.152±0.032) (0.026±0.002)
P2
6.35±1.3 L11.0 max.
(0.250±0.051) (0.433 max.)
F5.0±1.0t0.7±0.2
(0.197±0.039) (0.028±0.008)
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
Unit : mm (inch)
03:
04:
◦VB
Type Symbol Dimensions Symbol Dimensions
FBA03□450
FBA04□450
FBA04□600
FBA04□900
A
4.5±0.3 F5.0±1.0
(0.177±0.012) (0.197±0.039)
6.0＋0.5
ー0△h0.0±2.0
(0.236＋0.020
ー0)(0.0±0.079)
9.0±0.5 W18.0＋1.0
－0.5
(0.354±0.020) (0.709＋0.039
－0.020 )
A1
12.5 max. W0
12.5 min.
(0.492 max.) (0.492 min.)
16.0 max. W1
9.0＋0.75
－0.5
(0.630 max.) (0.354＋0.039
－0.020 )
φD3.7 max. W2
3.0 max. ※2
(0.146 max.) (0.118 max.)
H0
16.0±0.5 ℓ1.0 max.
(0.650±0.020) (0.039 max.)
P12.7±1.0 φD0
4.0±0.3
(0.500±0.039) (0.157±0.012)
P0
12.7±0.3 ※1
φd0.65±0.05
(0.500±0.012) (0.026±0.002)
P1
3.85±0.8 L11.0 max.
(0.152±0.032) (0.433 max.)
P2
6.35±1.3 t0.7±0.2
(0.250±0.051) (0.028±0.008)
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
Unit : mm (inch)
450:
600:
900:
900:
450:
600:
Type Symbol Dimensions Symbol Dimensions
FBR07
A
9.0 max. △h0.0±2.0
(0.354 max.) (0.0±0.079)
7.0 max. W18.0＋1.0
－0.5
(0.276 max.) (0.709＋0.039
－0.020 )
T2.5 max. W0
12.5 min.
(0.098 max.) (0.492 min.)
D7.5±0.5 W1
9.0＋0.75
－0.5
(0.925±0.020) (0.354＋0.039
－0.020 )
H
18.0＋2.0
ー0W2
3.0 max. ※2
(0.709＋0.079
ー0)(0.118 max.)
16.0±0.5 ℓ1.0 max.
(0.630±0.020) (0.039 max.)
P12.7±1.0 φD0
4.0±0.3
(0.500±0.039) (0.157±0.012)
P0
12.7±0.3 ※1
φd0.65±0.05
(0.500±0.012) (0.02±0.002)
P1
3.85±0.8 L11.0 max.
(0.152±0.028) (0.433 max.)
P2
6.35±1.3 t0.7±0.2
(0.250±0.051) (0.028±0.008)
F5.0＋1.0
ー0.5 Unit : mm(inch)
(0.197＋0.039
ー0.020 )
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
121:
850:
SB:
TB:
◦SB/TB (F : 5mm pitch) (0.197 inches)
11
le0104fi01_reli-RP1 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Operating temperature Range
LA Type
ー25～＋105℃CAL45 Type
LHL□□□
FBA/FBR ー25～＋85℃
FL05□ Type ー25～＋105℃
FL06BT Type
【Test Method and Remarks】
LA・CA・FL : Including self-generated heat
LHL□□□ : Including self-generated heat
3. Rated current
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : The maximum DC value having inductance within 10% and temperature incease within 40℃ (LA:20℃) by the application of DC bias.
LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the following specified
temperature by the application of DC bias.
Reference temperature : 25℃ (LHL08, LHL10, LHL13)
: 30℃ (LHL16, LHLP□□)
: 40℃ (LHLC08, LHLC10)
FB : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value.
This is not guaranteed for electrial characteristics during current application.
FL : The maximum DC value having temperature rise within specified value.
5. Inductance
LA Type
Within the specified toleranceCAL45 Type
LHL□□□
FBA/FBR
FL05□ Type Within the specified tolerance
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1KHz)
Measuring frequency : Specified frequency
FL05R□ : Measuring equipment : HP4262A or its equivalent
Measuring frequency : 1kHz
6. Q
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
2. Storage temperature Range
LA Type
ー40～＋85℃
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
4. Impedance
LA Type
CAL45 Type
LHL□□□
FBA/FBR Within the specified tolerance
FL05□ Type
FL06BT Type Refer to individual specification
【Test Method and Remarks】
FB : Measuring equipment : Impedance analyzer (HP4191A) or its equivalent
Measuring frequency : Specified frequency
FL06BT : Measuring equipment : 4291A (HP) or its equivalent
Measuring frequency : Specified frequency
11
le0104fi01_reli-RP2
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
11. Over current
LA Type No emission of smoke no firing.
CAL45 Type
LHL□□□There shall be no scorch or short of wire.
LHLC08,LHLC10 : There shall be no firing.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□/LA・CAL45 Type： Measuring current : Rated current×2
Duration : 5 min.
Number of measuring : one time
8. Self resonance frequency
LA Type Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Measuring equipment : Network analyzer (Anritsu MS620J or its equivalent)
LHL□□□ (except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent
9. Temperature characteristic
LA Type △L/L : Within ±5%
CAL45 Type
LHL□□□ △L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Change of maximum inductance deviation in step 1 to 5
Step Temperature (℃)
1 20
2ー25 (Minimum operating temperature)
3 20 (Standard temperature)
4＋85 (Maximum operating temperature)
5 20
LHL□□□ : Change of maximum inductance deviation in step 1 to 5
Temperature at step 1 : 20℃
Temperature at step 2 : Minimum operating temperature
Temperature at step 3 : 20℃ (Standard temperature)
Temperature at step 4 : Maximum operating temperature
Temperature at step 5 : 20℃
10. Tensile strength test
LA Type
No abnormality such as cut lead, or looseness.CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cut lead, or looseness.
FL05□ Type No abnormality such as cut lead, or looseness.
FL06BT Type
【Test Method and Remarks】
LA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
25 5
CA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
10 10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm) force (N) duration (s)
0.3＜φd≦0.5 5
30±50.5＜φd≦0.8 10
0.8＜φd≦1.2 25
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the axial diretion of the component during 10±1 seconds.
FL05R□ : Fix the body of a component in the direction to draw terminal,and gradually apply the tensile force of 4.9N.
7. DC Resisitance
LA Type
Within the specified tolerance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent)
LHL□□□・FB・FL : Measuring equipment : DC ohmmeter
11
le0104fi01_reli-RP3 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
12. Terminal strength : bending
LA Type
No abnormality such as cut lead, or looseness.
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.3＜φd≦0.5 2.5 0.25
0.5＜φd≦0.8 5 0.50
LH・FB : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation
is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter tensile
φd (mm)
Bending force
(N)
Mass reference weight
(kg)
0.3＜φd≦0.5 2.5 0.25
0.5＜φd≦0.8 5 0.5
0.8＜φd≦1.2 10 1.0
13. Insulation resisitance : between the terminals and body
LA Type
CAL45 Type
LHL□□□100MΩ min.
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Applied voltage : 500 VDC
Duration : 60 sec.
14. Insulation resistance : between terminals and core
LA Type
CAL45 Type
LHL□□□
FBA/FBR 1MΩ min. (Other than materail code MA)
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FBA・FBR : Applied voltage : 100 VDC
Duration : 60±5 sec.
15. Withstanding : between the terminals and body
LA Type
CAL45 Type
LHL□□□No abnormality such as insulation damage
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LHL□□□ : Accoding to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage : 500 VDC
Duration : 60 sec.
16. DC bias characteristic
LA Type △L/L : Within ー10%
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Measure inductance with appliation of rated current using LCR meter to compare it with the initial value.
17. Body strength
LA Type No abnormality as damage.
CAL45 Type
LHL□□□
FBA/FBR No abnormality such as cracks on body.
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA : Applied force : 30N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
CAL45 : Applied force : 50N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
FBA : Applied force : 50±3N
Duration : 30±1 sec.
11
le0104fi01_reli-RP4
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
18. Resisitance to vibration
LA Type △L/L : Within ±5%　Q : 30min
CAL45 Type △L/L : Within ±5%
LHL□□□ Appearance : No abnomality △L/L : Within ±5% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR Appearance : No abnomality Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm
Mounting method : Soldering onto printed board.
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FB ： Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm (But don't exceed acceleration 196m/s2 (two power))
Mounting method : Soldering onto printed board.
19. Resistance to shock
LA Type No significant abnormality in appearance
CAL45 Type
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Drop test
Impact material : concrete or vinyl tile
Height : 1m
Total number of drops : 10 times
20. Solderability
LA Type At least 75％ of terminal electrode is covered by new solder.
CAL45 Type
LHL□□□At least 75％ of terminal electrode is covered by new solder.
FBA/FBR At least 90％ of terminal electrode is covered by new solder.
FL05□ Type At least 75％ of terminal electrode is covered by new solder.
FL06BT Type
【Test Method and Remarks】
LA, CA : Solder temperature : 230±5℃
Duration : 2±0.5 sec.
LHL□□□ : Solder temperature : 235±5℃
Duration : 2±0.5 sec.
Immersion depth : Up to 1.5mm from bottom of case.
FB : Solder temperature : 230±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from terminal root.
FL05R□ : Solder temperature : 230±5℃
Duration : 2±0.5 sec.
Immersion depth : Up to 2 to 2.5mm from terminal root.
FL06BT : Solder temperature : 230±5℃
Duration : 3±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from terminal root.
21. Resisitance to soldering heat
LA Type No significant abnormality in appearance
CAL45 Type △L/L : Within ±5%
LHL□□□ No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30%(LHLP : only △L/L)
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05□ Type Refer to individual specification
FL06BT Type No significant abnormality in appearance Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Solder temperature : (CA) 270±5℃, (LA) 260±5℃
Duration : 5±0.5 sec. One time
Immersed conditions : Inserted into substrate with t=1.6mm
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□ : Solder bath method : Solder temperature : 260±5℃
Duration : 10±1 sec.
Up to 1.5mm from the bottom of case.
Manual soldering : Solder temperature : 350±10℃ (At the tip of soldering iron)
Duration : 5±1 sec.
Up to 1.5mm from the bottom of case.
Caution : No excessive pressing shall be applied to terminals.
Recovery : 4 to 24hrs of recovery under the standard condition after the test.
FB : Solder bath method : Condition 1 : Solder temperature : 260±5℃
Duration : 10±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Condition 2 : Solder temperature : 350±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
FL : Solder condition : 260±5℃ 10±1 sec.
Immersion depth : Up to 0.5 to 1.0mm from the terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
11
le0104fi01_reli-RP5 le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
22. Resisitance to solvent
LA Type Please avoid the ultrasonic cleaning of this product.
CAL45 Type
LHL□□□
FBA/FBR No significant abnormality in appearance Impedance change : Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
FB : Solvent temperature : 20～25℃
Duration : 30±5 sec.
Solvent type : Acetone, trichloroethylene
Recovery : 3hrs of recovery under the standard condition after the test.
23. Thermal shock
LA Type △L/L : Within ±10%　Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP：only △L/L)
FBA/FBR Appearance : No abnormality Impedance change : Within ±20%
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Conditions for 1cycle
Step Temperature (℃) Duration (min.)
1ー25＋0
ー330±3
2 Room temperature Within 3
3＋85＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 5 cycles
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs.
LHL□□□・FB : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1 Minimum operating temperature＋0
ー330±3
2 Room temperature Within 3
3 Minimum operating temperature＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 10 cycles 〔LHL□□□〕
: 5 cycles (FBA, FBR)
Recovery : 4 to 24hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR)
FL : Accoding to JIS C0025
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1ー25＋0
ー330±3
2 Room temperature Within 3
3＋85＋2
ー030±3
4 Room temperature Within 3
Number of cycles : 10 cycles
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
24. Damp heat
LA Type △L/L : Within ±10%　Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR Appearance：No abnormality Impedance change：Within ±20%
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
FB : Temperature : 60±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
11
le0104fi01_reli-RP6
le0104fi01_reli_e-01
■ RELIABILITY DATA
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
25. Loading under damp heat
LA Type △L/L : Within ±10%　Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Imductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000±24 hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 60±3℃
Humidity : 90～95%RH
Duration : 500 (＋12, ー0) hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
LA Type △L/L : Within ±10%　Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR
FL05□ Type
FL06BT Type
【Test Method and Remarks】
LA, CA : Temperature : 85±2℃
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
LA Type △L/L : Within ±10%　Q : 30min
CAL45 Type △L/L : Within ±10%
LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LA, CA : Temperature : ー25±2℃
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ : Temperature : ー40±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : ー40±3℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
LA Type
CAL45 Type
LHL□□□Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
FL05□ Type Refer to individual specification
FL06BT Type Appearance : No abnormality Impedance change : Within ±20%
【Test Method and Remarks】
LHL□□□ : Temperature : 105±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
FL : Temperature : 85±3℃
Duration : 500 (＋12, ー0) hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
11
le0104fi01_reli-RP7 le0104fi01_reli_e-01
■ PRECAUTIONS
＊ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems,
measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high
reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where
product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions ◆Design
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
Technical
consider-
ations
◆Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of
the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
consider-
ations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc
sufficiently.
Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical
consider-
ations
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of
the products.
5. Cleaning
Precautions
◆Cleaning conditions
1. CAL type, LH type, LA Type
Please do not do cleaning by a supersonic wave.
Technical
consider-
ations
◆Cleaning conditions
1. CAL type, LH type, LA Type
If washing by supersonic waves, supersonic waves may deform products.
6. Handling
Precautions
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item).
Technical
consider-
ations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should
be controlled.
Recommended conditions
・Ambient temperature 0～40℃
・Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
consider-
ations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of
taping/packaging materials may take place.
CAL Type, LH Type, FB Type, FL Type, LA Type