54AC280 54AC280 9-Bit Parity Generator/Checker Literature Number: SNOS144 54AC280 9-Bit Parity Generator/Checker General Description Features The 'AC280 is a high-speed parity generator/checker that accepts nine bits of input data and detects whether an even or an odd number of these inputs is HIGH. If an even number of inputs is HIGH, the Sum Even output is HIGH. If an odd number is HIGH, the Sum Even output is LOW. The Sum Odd output is the complement of the Sum Even output. n ICC reduced by 50% n 9-bit width for memory applications n Standard Microcircuit Drawing (SMD) 5962-92201 Logic Symbols Connection Diagrams Pin Assignment for DIP and Flatpak DS100359-1 IEEE/IEC DS100359-2 Pin Assignment for LCC DS100359-4 Pin Names Description DS100359-3 I0-I8 Data Inputs O Odd Parity Output E Even Parity Output Truth Table Number of HIGH Inputs Outputs Even Odd I0-I8 0, 2, 4, 6, 8 H L 1, 3, 5, 7, 9 L H H = HIGH Voltage Level L = LOW Voltage Level FACTTM is a trademark of Fairchild Semiconductor Corporation. (c) 1998 National Semiconductor Corporation DS100359 www.national.com 54AC280 9-Bit Parity Generator/Checker September 1998 Logic Diagram DS100359-5 Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. www.national.com 2 Absolute Maximum Ratings (Note 1) CDIP If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) DC Input Diode Current (IIK) VI = -0.5V VI = VCC + 0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO = -0.5V VO = VCC + 0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current per Output Pin (ICC or IGND) Storage Temperature (TSTG) Junction Temperature (TJ) 175C Recommended Operating Conditions -0.5V to +7.0V Supply Voltage (VCC) 'AC Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) 54AC Minimum Input Edge Rate (V/t) 'AC Devices VIN from 30% to 70% of VCC VCC @ 3.3V, 4.5V, 5.5V -20 mA +20 mA -0.5V to VCC + 0.5V -20 mA +20 mA -0.5V to VCC + 0.5V 50 mA 2.0V to 6.0V 0V to VCC 0V to VCC -55C to +125C 125 mV/ns Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, output/input loading variables. National does not recommend operation of FACT circuits outside databook specifications. 50 mA -65C to +150C DC Characteristics for 'AC Family Devices Symbol Parameter 54AC TA = VCC (V) Units Conditions -55C to +125C Guaranteed Limits VIH VIL VOH Minimum High Level 3.0 2.1 Input Voltage 4.5 3.15 5.5 3.85 Maximum Low Level 3.0 0.9 Input Voltage 4.5 1.35 5.5 1.65 Minimum High Level 3.0 2.9 Output Voltage 4.5 4.4 5.5 5.4 VOUT = 0.1V V or VCC - 0.1V V or VCC - 0.1V VOUT = 0.1V IOUT = -50 A V (Note 2) VIN = VIL or VIH VOL 3.0 2.4 4.5 3.7 5.5 4.7 Maximum Low Level 3.0 0.1 Output Voltage 4.5 0.1 5.5 0.1 IOH = -12 mA V IOH = -24 mA IOH = -24 mA IOUT = 50 A V (Note 2) VIN = VIL or VIH IIN Maximum Input 3.0 0.50 4.5 0.50 5.5 0.50 5.5 1.0 IOL = 12 mA V IOL = 24 mA A IOL = 24 mA VI = VCC, GND Leakage Current IOLD IOHD Minimum Dynamic Output Current (Note 3) 5.5 50 mA VOLD = 1.65V Max 5.5 -50 mA VOHD = 3.85V Min 3 www.national.com DC Characteristics for 'AC Family Devices (Continued) Symbol 54AC TA = Parameter VCC (V) Units Conditions -55C to +125C Guaranteed Limits ICC Maximum Quiescent 5.5 80.0 A Supply Current VIN = VCC or GND Note 2: All outputs loaded; thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit @ 5.5V VCC. AC Electrical Characteristics VCC 54AC TA = -55C Parameter (V) (Note 5) to +125C CL = 50 pF tPLH Propagation Delay 3.3 1.0 20.0 tPHL In to E 5.0 1.0 14.5 tPLH Propagation Delay 3.3 1.0 20.0 tPHL In to O 5.0 1.0 14.5 Symbol Min Max Note 5: Voltage range 3.3 is 3.3V 0.3V. Voltage range 5.0 is 5.0V 0.5V. Capacitance Typ Units CIN Symbol Input Capacitance 4.5 pF CPD Power Dissipation Capacitance 75.0 pF www.national.com Parameter 4 Units Conditions VCC = OPEN VCC = 5.0V ns ns Physical Dimensions inches (millimeters) unless otherwise noted 20 Terminal Ceramic Leadless Chip Carrier NS Package Number E20A 14 Lead Ceramic Dual-In-Line Package NS Package Number J14A 5 www.national.com 54AC280 9-Bit Parity Generator/Checker Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14 Lead Ceramic Flatpak (F) NS Package Number W14B LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated