NEW
2014.3 1
75 Ω Small Coaxial Connectors (SMT Low Profi le)
H.FL75 Series 75 ø, up to 3 GHz
■Features
1. Miniature, 75
Ω
coaxial RF connector
A mated receptacle and right-angled plug
delivers a low mated height of only 3 mm from
the printed circuit board (see Fig. q).
2. High impedance matching
High impedance matching is used to produce its
high frequency response from DC to 3 GHz,
which is suitable for 3G-SDI broadcasting
equipment.
3.
Terminated with 75 Ω, ultra-fine coaxial cable
The use of Ø1.5 mm, ultra-fine coaxial (fluorinated
resin insulated) cables make this connector
perfect for applications that require wiring in tight
spaces.
4.
Suitable for use with 3G-SDI equipment
Used together with BNC (75) Series connectors,
it’s possible to maintain 75 ø system lines from
the interface connections to the internal wiring
systems.
5. Supports automatic mounting
The receptacles are packaged on reels which
supports automatic pick-and-place mounting.
Capped receptacles are available and are
suitable for use with virtually all types of
mounting machines.
6. Easy mating with protected design
The design structure emits a clear tactile click
when mating is completed. Even though small
in size, the receptacle’s design adds extra
protection to the mating area.
7. Simple un-mating process
An extraction tool is available which simplifies
the un-mating process.
6.5
H.FL-R-SMT
3
H.FL75-LP（G）-084
Interface: BNC (75) Series
Internal wiring: H.FL75 Series
Figure 1 Connector mating external view
Figureq
2
H.FL75 Series●75 Ω Small Coaxial Connectors (SMT Low Profile)
■Product Specifi cations
Ratings
Nominal characteristic impedance: 75 ø
Operating temperature range: -40ç to +90ç (RH 90% max.)
Voltage: AC 60 V rms
Storage temperature range: -30ç to +70ç (RH 90% max.)
Frequency range: DC to 3 GHz
Items Specifi cations Conditions
1. Contact resistance Center:Maximum of 20 mø
Outer: Maximum of 10 mø Measured with 10 mA max.
2. Insulation resistance Minimum of 500 Mø Measured with 250 VDC
3. Withstanding voltage No fl ashover or insulation breakdown AC 300 V / 1 minute.
4. V.S.W.R. (*) Maximum of 1.25 DC to 1.5 GHz
Maximum of 1.5 1.5 to 3 GHz
5. Holding power of
female contact Minimum of 0.15 N Measured withØ0.475 pin gauge.
6. Total mating/
unmating force Maximum of 30 N Measured with applicable connector.
7. Durability (mating/
unmating with
corresponding plug)
Contact resistance
Center: Maximum of 25 mø
Outer: Maximum of 15 mø
50 mating cycles.
8. Vibration resistance No electrical discontinuity for 1 µs or more.
No damaged, cracks or loose parts.
Frequency of 10 to 100 Hz, single amplitude of 1.5
mm, acceleration of 59 m/s2, for 5 cycles in each
of the 3 axes direction.
9. Shock resistance No electrical discontinuity for 1 µs or more.
No damaged, cracked or loose parts.
Acceleration of 735 m/s2, for a duration of 11 ms,
sine half-wave waveform, 3 cycles in each of the 6
axes direction.
10. Humidity resistance
(Steady state)
No damaged, cracked or loose parts
Insulation resistance: 10 Mø min. (high humidity)
Insulation resistance: 500 Mø min. (dry)
96 hours at temperature of 40ç and humidity of
95％.
11. Temperature cycle
No damaged, cracked or loose parts.
Contact resistance
Center: Maximum of 25 mø
Outer: Maximum of 15 mø
Temperature: -40ç → +5 to +35ç → +90ç →
+5 to +35ç
Time: 30 → 5 max. → 30 → 5 max. (minutes)
5 Cycles
12. Salt spray No excessive corrosion 5％ salt water solution for 48 consecutive hours
*V.S.W.R. Measurement System
The above V.S.W.R. specifi cation values were measured using the measurement system shown below.
■Materials
Part Material Finish Remarks
Shell Phosphor bronze Silver plated —
Male center contact Brass Gold plated —
Female center contact Phosphor bronze Gold plated —
Insulator Plug PBT Resin Black UL94V-0
Receptacle LCP Black UL94V-0
Note 1:
Cable type connectors were measured with BNC (75) conversion adapters
attached to both ends of the harness product of a suitable 10 cm cable.
Note 2:
Board type connectors were mounted to a 75 ø glass epoxy board
and measurements were conducted with N (75) connectors attached.
Network Analyzer
Test Set
Test Port
TerminationD.U.T
Test Port Cable
■Plug
75
6.5
[Plugs are only sold as cabled assemblies]
3
H.FL75 Series●75 Ω Small Coaxial Connectors (SMT Low Profile)
Maximum of 1.5
(Note 3)
Ø0.5
GND
GND
GND
SIG
Ø2.4
1.7
3-0.8
0.6
4.5
5
4
4.5
■Standard Tolerances for (L)
L (mm) Standard Tolerance
(mm)
35 ≦L≦200 ±4
200 ＜L≦500 ±8
500 ＜L≦1000 ±12
1000 ＜L ±1.5％ of L
Note: 35 mm is the shortest length (L) that can be made.
■ Product Number Structure of
Cable Assemblies
Refer to this page when determining product specifications
by model types. Please place orders with part numbers
listed in this catalog. The characteristics and specifications
of the product described in this catalog are reference
values. Please make sure to check the latest delivery
specifications at the time of product use.
H.FL75 -「」LPG -「」-A- (L)
❶❷ ❸ ❹
❶Series name H.FL75
❷ Assembly type None: Single-ended,
2: Double-ended
❸Cable type 084N: for Ø1.5 mm cable
❹ Cable color 1: White, 2: Black, 4: Blue
❺Total length L (mm) L length in mm
■How to Specify Plug Cable Assembly
The dimensions of a cable assembly of the H.FL75 series should be specified as follows:
[Single-Ended Cable Assembly] [Double-Ended Cable Assembly]
L（mm）L（mm）
Note 1:
Receptacles that are specifi ed by (01) are sold in 100 piece packs.
Please order in full pack quantities.
Note 2: Receptacles that are specifi ed by (10) are sold in full reel
quantities, each reel contains 2,500 pieces.
Please order in full reel quantities.
Note 3: This area may be covered by insulating material.
Note 4: The H.FL-R-SMT (C) (10) comes equipped with a cap that
allows it to be mounted by almost any pick and place machine.
Remove cap after the refl ow process.
Part No. HRS No. Packaging Remarks
H.FL-R-SMT(01)CL331-0521-6-01 100 pieces per pack −
H.FL-R-SMT(10)CL331-0521-6-10 2,500 pieces per reel −
H.FL-R-SMT(C)(10)CL331-0522-9-10 2,500 pieces per reel With caps
■Receptacle
Cap
With cap
installed
3-1.2±0.05
2±0.05
2.8±0.05
3±0.05
1.5±0.05 1±0.05
1.2±0.05
3.1±0.05
3.1±0.05
GND
GND GND
SIG
Recommended PCB
layout dimensions
4
H.FL75 Series●75 Ω Small Coaxial Connectors (SMT Low Profile)
Part No. HRS No. RoHS
BNC(75)J-H.FLJ-BPA(40)CL311-0302-8-40 ○
Part No. HRS No. RoHS
H.FL-LP-N CL331-0551-7 ○
■Conversion Adapter
●BNC (75) Conversion Adapter (Mating portion - H.FL75 side: jack - BNC (75) side: jack)
BPlug Extraction Tool
This is the recommended tool for un-mating the plug when in the mated condition.
BEmbossed Carrier Tape Dimensions (JIS-C-0806 compliant)
The diagram below shows the embossed carrier tape dimensions used to package the H.FL-R-SMT(10).
24
8
Ø1.5
Unreeling direction
Center contact
5.5 1.75
12
（2.4）
14
Ø330
2
Ø21
Ø13
ReelDimensions
8.2
＋
0.1
0
φ2.4
12.5
21.3
φ13
φ
9.6
＋
0.1
0
Ø15
3.3
6
40
100
3
5
H.FL75 Series●75 Ω Small Coaxial Connectors (SMT Low Profile)
BUsage Precautions
1.Plugs
(1) Mating / un-mating
qTo disconnect the connector, insert the extraction tool (H.FL-LP-N) under
the connector fl ange. Pull in a perpendicular direction, or in the direction
of the connectors mating axis.
Do not un-mate the plug by pulling on the cable, this can damage the
connector and alter its performance.
wTo mate the connector, align the mating axes between the receptacle
and cable assembly, and insert the cable assembly downward and
perpendicular into the receptacle.
Do not insert the cable assembly at a slanted angle.
(2) Allowable load to a cable when
mated.
After the connector has been mated, prevent excessive force being
placed onto the cable. Please reference the tolerances listed below.
Maximum
of 5 N
H.FL-LP*
H.FL-R-SMT
Maximum
of 3 N
Maximum
of 3 N
(3) Precautions
Do not use excessive prying forces to mate or un-mate these connectors, failure
to follow this precaution can lead to the connector becoming damaged.
2. Receptacles
(1) Recommended refl ow
temperature profi le[reference]
Refl ow temperature profi le (reference)
q
The temperatures indicated are the surface temperatures of the
printed circuit board near the terminal contact points.
w
Refl ow soldering should be performed at a peak temperature of
250ç or less at the surface of the printed circuit board.
e
Temperature profi les may vary due to external mounting conditions;
conditions such as solder paste types, manufacturer, PCB size and
any other soldering materials may alter the performance of such
materials.
(2) Recommended manual
soldering [reference]
Soldering iron temperature: 350ç, soldering time: Maximum of 5
seconds.
(3)
Recommended metal mask thickness
0.1 to 0.15 mm
(4) Refl ow cycles Maximum of 2 cycles
3.Operating Environment and Storage Conditions
(1) Operating environment This product was designed on the assumption that it will be used in a
normal environment.
Please be advised that using these connectors in certain environments
may lead to discoloration or other types of degradation.
・
Exposed to a excessive amounts of fi ne particles and dust
・
Regions and places having a high density of sulfur dioxide, hydrogen
sulfi de, nitrogen dioxide or other corrosive gasses. (e.g., exhaust gas
from automobiles or factories)
・Environments that experience large changes in temperatures, such as
locations near a heater.
(2) Storage conditions
Store the product in Hirose Electric's packaging or similar packaging conditions.
Temperature: -10 to +40ç, humidity: 85% or less (recommended storage
conditions)
We recommend that this product be consumed within six months from delivery.
For products that have been stored and the storage period has expired, they
need to be tested for solderability before use.
80
100
120
140
160
180
200
220
240
［ç］
260
230ç
220ç
Maximum of 120 seconds
Time
Maximum of 50 seconds
Peak temperature
250ç, 10 seconds
Maximum of 60 seconds
Temperature
6
H.FL75 Series●75 Ω Small Coaxial Connectors (SMT Low Profile)
BHigh Frequency Characteristics of related 75
Ω
Hirose products
●BNC (75) Series
100
100
100
100
BNC(75)-BPJ-1.5CV-※BNC(75)-BPJ-1.5CV-※
BNC(75)-BPJ-1.5CV-※PL71-LP-1.5C(40)
BNC(75)-BPJ-1.5CV-※PL71-LP-1.5CV
BNC(75)J-H.FLJ-BPA(40)
H.FL75-2LPG-084N※-L
Frequency［GHz］
Frequency［GHz］
Frequency［GHz］
Frequency［GHz］
V.S.W.R.V.S.W.R.
V.S.W.R.V.S.W.R.
0 0.5 1 1.5 2 2.5 3
0 0.5 1 1.5 2 2.5 3
0 0.5 1 1.5 2 2.5 3
0 0.5 1 1.5 2 2.5 3
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 3/2014. Contents are subject to change without notice for the purpose of improvements.
6-3,Nakagawa Chuoh-2-Chome,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
TEL: +81-45-620-3526 Fax: +81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
®
●PL71 Series
●PL75 Series
●H.FL75 Series
