■ Smoothing of PWM drive output voltage
■ Efficient motor protection
■ Increase of motor service life
■ Reduction of audible motor noise
■ Reduction of parasitic losses
■ Improvement of system reliability
Output filters
FN 5010
Universal sine wave output filter
for motor drives
Tec
h
n
i
ca
l
spec
ifi
cat
i
ons
Nominal operating voltage: 3x 400VAC (FN 5010)
3x 690VAC (FN 5010HV)
Motor frequency: 0 to 70Hz
Switching frequency: 4 to 16kHz
Rated currents: 2.5 to 610A @ 40°C
Motor cable length: max. 400m shielded
max. 300m unshielded
Impedance (uk): 10% @ nominal voltage, 50Hz & rated current
Residual ripple voltage: <5%
High potential test voltage: P –> E 3000VAC for 3 sec
P –> P 2000VAC for 3 sec
Protection category: IP00 (filters up to 150A according to VBG4)
Overload capability: 2x rated current at switch on for 30 seconds,
1.5x rated current for 1 minute, once per hour
Temperature range (operation and storage): -25°C to +85°C (25/085/21)
Insulation class: T40/F (155°C)
Flammability corresponding to: UL94V-2 or better
Design corresponding to: EN61558-2-20 (VDE0570-2-20)
Typ
i
ca
l
e
l
ectr
i
ca
l
sc
h
emat
i
c
Features an
d
b
ene
fi
ts Typ
i
ca
l
app
li
cat
i
ons
■ Motor drive applications with long
motor cables
■ Pumps
■ Conveyors
■ HVAC applications
■ Elevators
■ General automation tasks
■ Applications with multiple motors
in parallel
■ Conversion of the PWM output signal
(symmetrical voltage components) of
motor drives into a smooth sine wave with
low residual ripple.
■ Elimination of premature motor damage
caused by high dv/dt, over voltages, motor
overheating and eddy current losses.
■ Significantly increased service life of
electric motors.
■ Reduction of the pulse load of motor drive
IGBT‘s and the parasitic losses on long
shielded motor cables.
■ Cost effective and space saving open frame
filter design.
■ Vacuum impregnation ensures less
humming noise and high durability.
Approva
l
s
By January 2006
@ 40°C power rating* inductance capacitance power loss** connections Total Cu. Al.
[A] [kW] [mH] [µF] [W] [kg] [kg] [kg]
F
il
ter se
l
ect
i
on ta
bl
e
FN 5010-2.5-99 2.5 1.1 22.4 1.5 50 -99 2.6 0.68
FN 5010-3.5-99 3.5 1.5 16 1.5 54 -99 2.6 1.05
FN 5010-4.5-99 4.5 2.2 11 1.5 66 -99 3 1.1
FN 5010-6.5-99 6.5 3 8.4 1.5 70 -99 5.4 2.1
FN 5010-8-99 8 4 7.2 1.5 73 -99 6.6 2.2
FN 5010-10-99 10 5.5 4.2 1.5 91 -99 6.6 2.6
FN 5010-13-99 13 7.5 4.2 1.5 124 -99 7.3 3.2
FN 5010-18-99 18 11 3.5 1.5 144 -99 11.5 3.6
FN 5010-24-99 24 15 2.4 1.5 191 -99 14 5
FN 5010-32-99 32 18.5 2 2 273 -99 16 6.8
FN 5010-42-99 42 22 1.58 7 252 -99 22 7.4
FN 5010-48-99 48 30 1.5 4 340 -99 28 8.8
FN 5010-60-99 60 30 1.1 4 290 -99 35 10.9
FN 5010-75-99 75 37 0.9 4 340 -99 42 11.5
FN 5010-90-99 90 45 0.8 5 360 -99 46 12.8
FN 5010-110-99 110 55 0.7 5 400 -99 58 13
FN 5010-150-99 150 75 0.5 7 716 -99 75 14.8
FN 5010-180-99 180 90 0.4 10 820 -99 88 1.4 10.9
FN 5010-210-99 210 110 0.4 10 1065 -99 115 2.1 11.2
FN 5010-270-99 270 132 0.3 12 1230 -99 150 2.1 14
FN 5010-325-99 325 160 0.3 12 1820 -99 194 5.2 21
FN 5010-410-99 410 200 0.2 18 1830 -99 206 5.2 23.8
FN 5010-480-99 480 250 0.185 20 2100 -99 255 6.5 28
FN 5010-510-99 510 315 0.17 20 2255 -99 290 6.5 32
FN 5010-610-99 610 355 0.14 25 2520 -99 330 7.7 37.5
FN 5010HV-2.5-99 2.5 1.5 61 1.5 60 -99 5.8 0.86
FN 5010HV-3.5-99 3.5 2.2 43.5 1.5 64 -99 6.6 1.55
FN 5010HV-4.5-99 4.5 3 33.5 1.5 63 -99 7.5 2.4
FN 5010HV-6.5-99 6.5 4 23.5 1.5 73 -99 11.2 3.95
FN 5010HV-8-99 8 5.5 19 1.5 83 -99 13.3 4.35
FN 5010HV-10-99 10 7.5 15.2 1.5 102 -99 15.8 5.7
FN 5010HV-13-99 13 11 11.7 1.5 124 -99 18.9 6
FN 5010HV-18-99 18 15 8.4 1.5 136 -99 27.2 9.5
FN 5010HV-24-99 24 18.5 6.3 2.2 189 -99 29.7 11
FN 5010HV-32-99 32 22 4.7 2.2 264 -99 46.5 15.7
FN 5010HV-42-99 42 30 3.6 4.7 254 -99 53.6 16.4
FN 5010HV-48-99 48 37 3.1 4.7 380 -99 66 16.9
FN 5010HV-60-99 60 45 2.5 4.7 528 -99 70.7 17.4
FN 5010HV-75-99 75 55 2 5.6 631 -99 78 19.6
FN 5010HV-90-99 90 75 1.75 5.6 793 -99 94.7 25.2
FN 5010HV-110-99 110 90 1.38 10 898 -99 112 27.8
FN 5010HV-150-99 150 110 1 10 1121 -99 152 29.6
FN 5010HV-180-99 180 160 0.85 12 1140 -99 181 2.3 17.8
FN 5010HV-210-99 210 200 0.73 18 1392 -99 200 3.4 19.6
FN 5010HV-270-99 270 250 0.56 18 1495 -99 210 3.4 26.6
FN 5010HV-325-99 325 315 0.47 22 1612 -99 232 4.9 35
FN 5010HV-410-99 410 355 0.37 28 1876 -99 277 6.3 47.6
FN 5010HV-480-99 480 400/450 0.32 36 2225 -99 289 8.4 49.7
FN 5010HV-510-99 510 450 0.3 36 2400 -99 303 8.4 51.4
FN 5010HV-610-99 610 500 0.25 44 2740 -99 335 13 53.9
* General purpose 4-pole (1500r/min) AC induction motor rated 400V/50Hz for FN 5010 filters, 690V/50Hz for FN 5010HV filters.
** Exact value depends upon the motor cable type and length, switching frequency, motor frequency and further stray parameters within the system.
Filter Rated current Typical motor Nominal Nominal Typical Input/Output Weight
> Components >
FN 5010
Typ
i
ca
l
bl
oc
k
sc
h
emat
i
c
Mec
h
an
i
ca
l
d
ata
2.5 to 42A types 48 to 150A types
180 to 610A types
> Components >
FN 5010
FN 5010 A B B1 C D E F G
D
i
mens
i
ons
2.5 and 3.5A 125 65 110 180 100 45 5 x 8 2.5mm²
4.5A 125 75 110 180 100 55 5 x 8 2.5mm²
6.5 155 80 118 205 130 55 8 x 12 4mm²
8 and 10A 155 95 118 205 130 70 8 x 12 4mm²
13A 190 100 125 230 170 58 8 x 12 4mm²
18A 190 120 125 230 170 78 8 x 12 10mm²
24A 210 125 135 260 175 85 8 x 12 10mm²
32A 210 135 135 260 175 95 8 x 12 10mm²
42A 230 140 150 285 180 122 8 x 12 10mm²
48A 240 210 <B 290 190 125 8 x 12 10mm²
60A 240 220 <B 290 190 135 8 x 12 16mm²
75A 300 210 <B 345 240 134 11 x 15 35mm²
90A 300 215 <B 345 240 139 11 x 15 35mm²
110A 300 237 <B 345 240 161 11 x 15 50mm²
150A 420 217 <B 470 370 142 11 x 15 50mm²
180A 420 235 <B 470 370 157 11 x 15 Ø11
210A 420 260 <B 470 370 182 11 x 15 Ø11
270A 420 295 <B 470 370 217 11 x 15 Ø11
325 and 410A 480 310 <B 580 430 234 13 x 18 Ø11
480A 500 340 <B 670 430 238 13 x 18 Ø11
510A 500 370 <B 670 430 248 13 x 18 Ø11
610A 500 370 <B 670 430 268 13 x 18 Ø11
All dimensions in mm; 1 inch = 25.4mm
Tolerances according: ISO2768 / EN22768
FN 5010HV A B B1 C D E F G
D
i
mens
i
ons
2.5 to 4.5A 155 95 118 205 130 70 8 x 12 2.5mm²
6.5A 190 110 125 230 170 68 8 x 12 4mm²
8A 190 120 125 230 170 78 8 x 12 4mm²
10A 210 125 135 260 175 85 8 x 12 4mm²
13A 210 135 135 260 175 95 8 x 12 4mm²
18 and 24A 230 160 <B 290 180 122 8 x 12 10mm²
32A 300 215 <B 345 240 135 11 x 15 10mm²
42A 300 232 <B 345 240 152 11 x 15 10mm²
48A 360 235 <B 420 310 136 11 x 15 10mm²
60A 360 241 <B 420 310 142 11 x 15 16mm²
75A 360 261 <B 420 310 157 11 x 15 35mm²
90A 420 228 <B 470 370 153 11 x 15 35mm²
110A 420 248 <B 470 370 173 11 x 15 50mm²
150A 420 288 <B 470 370 213 11 x 15 50mm²
180A 480 350 <B 470 430 258 13 x 18 Ø11
210 and 270A 480 340 <B 580 430 248 13 x 18 Ø11
325A 480 350 <B 580 430 258 13 x 18 Ø11
410A 480 350 <B 690 430 258 13 x 18 Ø11
480A 480 360 <B 690 430 268 13 x 18 Ø11
510A 480 370 <B 690 430 278 13 x 18 Ø11
610A 480 360 <B 790 430 268 13 x 18 Ø11
All dimensions in mm; 1 inch = 25.4mm
Tolerances according: ISO2768 / EN22768
> Components >
FN 5010
Your local partner: To find your local partner within Schaffner’s global network, please go to www.schaffner.com February 2006
