SG1577 Dual Synchronous DC/DC Controller Features Description Integrated Two Sets of MOSFET Drivers Wide Range Input Supply Voltage: 8~15 V Two Soft-Start / EN Functions The SG1577 is a high-efficiency, voltage-mode, dualchannel, synchronous DC/DC PWM controller for two independent outputs. The two channels are operated out of phase. The internal reference voltage is trimmed to 0.7 V 1.5%. It is connected to the error amplifier's positive terminal for voltage feedback regulation. The soft-start circuit ensures the output voltage can be gradually and smoothly increased from zero to its final regulated value. The soft-start pin can also be used for chip-enable function. When two soft-start pins are grounded, the chip is disabled and the total operation current can be reduced to under 0.55 mA. The fixedfrequency is programmable from 60 kHz to 320 kHz. The Over-Current Protection (OCP) level can be programmed by an external current sense resistor. It has two integrated sets of internal MOSFET drivers. SG1577 is available in the 20-pin SOP package. Two Independent PWM Controllers Constant Frequency Operation: Free-running Fixed Frequency Oscillator Programmable: 60 kHz to 320 kHz Programmable Output as Low as 0.7 V Internal Error Amplifier Reference Voltage: 0.7 V 1.5% Programmable Over-Current Protection (OCP) 30 V HIGH Voltage Pin for Bootstrap Voltage Output Over-Voltage Protection (OVP) SOP 20-Pin Applications CPU and GPU Vcore Power Supply Power Supply Requiring Two Independent Outputs Ordering Information Part Number Operating Temperature Range SG1577SY -40C to +85C (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 Package 20-Lead, Small Outline Package (SOP-20) Packing Method Tape & Reel www.fairchildsemi.com SG1577 -- Dual Synchronous DC/DC Controller November 2012 Figure 1. Typical Application SG1577 -- Dual Synchronous DC/DC Controller Application Diagram Internal Block Diagram Figure 2. (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 Functional Block Diagram www.fairchildsemi.com 2 F ZXYTT SG1577 TPM F: Fairchild Logo Z: Plant Code X: 1-Digit Year Code for SOP Y: 1-Digit Week Code for SOP TT: 2-Digit Die Run Code T: Package Type (S = SOP) P: Z=Lead Free + ROHS Compatible Y=Green Package M: Manufacture Flow Code Figure 3. Top Mark (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 SG1577 -- Dual Synchronous DC/DC Controller Marking Diagram www.fairchildsemi.com 3 Figure 4. SOP-20 Pin Configuration (Top View) Pin Definitions Name Pin # Type Description RT 1 Frequency Select Switching frequency programming pin. An external resistor connecting from this pin to GND can program the switching frequency. The switching frequency would be 60 kHz when RT is open and become 320 kHz when a 30 k RT resistor is connected. IN1 2 Feedback Inverting input of the error amplifier. It is normally connected to the switching power supply output through a resistor divider. COMP1 3 Compensation Output of the error amplifier and input to the PWM comparator. It is used for feedback loop compensation. SS1/ENB 4 Soft Start/Enable A 10 A internal current source charging an external capacitor for soft start. Pull down this pin and pin 17 can disable the chip. CLP1 5 Over Current Protection Over-current protection for high-side MOSFET. Connect a resistor from this pin to the high-side supply voltage to program the OCP level. BST1 6 Boost Supply Supply for high-side driver. Connect to the internal bootstrap circuit. DH1 7 High-Side Drive CLN1 8 Switch Node Channel 1, high-side MOSFET gate driver pin. Switch-node connection to inductor. For channel 1 high-side driver's reference ground. DL1 9 Low-Side Drive Low-side MOSFET gate driver pin. PGND 10 Driver Ground Driver circuit GND supply. Connect to low-side MOSFET GND. VCC 11 Power Supply Supply voltage input. DL2 12 Low-Side Drive CLN2 13 Switch Node DH2 14 High-Side Drive BST2 15 Boost Supply Supply for high-side driver. Connect to the internal bootstrap circuit. CLP2 16 Over-Current Protection Over-current protection for the high-side MOSFET. Connect a resistor from this pin to the high-side supply voltage to program the OCP level. SS2/ENB 17 Soft-Start/Enable A 10 A internal current source charging an external capacitor for soft start. Pull down this pin and pin 4 can disable the chip. COMP2 18 Compensation Output of the error amplifier and input to the PWM comparator. It is used for feedback-loop compensation. IN2 19 Feedback Inverting input of the error amplifier. It is normally connected to the switching power supply output through a resistor divider. GND 20 Control Ground (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 SG1577 -- Dual Synchronous DC/DC Controller Pin Configuration Low-side MOSFET gate driver pin. Switch-node connection to inductor. For channel 2, high-side driver's reference ground. Channel 2 high-side MOSFET gate driver pin. Control circuit GND supply. www.fairchildsemi.com 4 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. All voltage values, except differential voltages, are given with respect to the network ground terminal. Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. Symbol VCC BST1(or 2) - CLN1(or 2) Parameter Max. Unit Supply Voltage, VCC to GND 16 V BST1(2) to CLN1(2) 16 V 18 V 30 V 16 V VCC+0.3 V CLN1(or 2) -GND CLN1(2) to GND for 100 ns Transient BST1(or 2) - GND BST1(2) to GND for 100 ns Transient Min. -4 DH1(or 2) - CLN1(or 2) CLN1(or 2), DL1(or 2) PGND JA TJ TSTG ESD -0.3 PGND to GND 1 V Thermal Resistance, Junction-to-Air 90 C/W C Operating Junction Temperature -40 +125 Storage Temperature Range -65 +150 C Human Body Model, JESD22-A114 2.5 kV Charged Device Model, JESD22-C101 750 V SG1577 -- Dual Synchronous DC/DC Controller Absolute Maximum Ratings Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings. Symbol Parameter Min. Max. Unit VCC Supply Voltage +8 +15 V TA Operating Ambient Temperature -40 +85 C (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 www.fairchildsemi.com 5 VCC=12 V, TA =25C, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. RRT=OPEN 54 60 66 RRT=GND 288 320 352 20 kRRT -10 Unit Oscillator fosc Oscillator Frequency fosc,rt Total Accuracy DON_MAX Maximum Duty Cycle KHz 10 % 85 90 95 % 0.6895 0.7000 0.7105 V Error Amplifier VREF Internal Reference Voltage (1) VCC=8 V, VCC=15 V 0.03 mV/C Open-Loop Voltage Gain 77 dB VREF Temperature Coefficient AVOL BW TA=0~85 C Unity Gain Bandwidth 3.5 MHz PSRR Power Supply Rejection Ratio 50 dB ISOURCE Output Source Current IN1=IN2=0.6 V Output Sink Current IN1=IN2=0.8 V 500 A VH COMP Output Voltage IN1=IN2=0.6 V 5 V VL COMP Output Voltage IN1=IN2=0.8 V 100 mV Soft-Start Charge Current VCLPVCLN 8 10 12 A Soft-Start Discharge Current VCLPVCLN 0.8 1.0 1.2 A OC Sink Current VCC=12 V 90 120 150 A ISINK 60 80 100 A SG1577 -- Dual Synchronous DC/DC Controller Electrical Characteristics Soft Start ISOURCE ISINK Protections IOSCET Over-Temperature 150 C TOT_hys TOT Over-Temperature Hysteresis 20 C VOVP Over-Voltage Protection of IN VOVP/VIN 112 IDH High-Side Current Source VBST - VCLN=12 V,VDH VCLN=6 V 1.0 RDH High-Side Sink Resistor VBST - VCLN=12 V IDL Low-Side Current Source VCC=12 V,VDL=6 V 125 % Output 1.7 3.3 1.0 RDL Low-Side Sink Resistor VCC=12 V tDT Dead Time(2) VCC=12 V, DH and DL=1000 pF 10 3.3 A 4.0 3.1 4 40 70 ns 4.3 5.3 mA 0.55 1.00 mA 1.7 A Total Operating Current ICC_OP Operating Supply Current VCC=12 V, No Load ICC_SBY Standby Current (Disabled) SS1/ENB=SS2/ENB=0 V Notes: 1. Not test in production, 30 pcs sample. 2. When VDL falls less than 2 V relative to VDH rising to 2 V. (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 www.fairchildsemi.com 6 Unless otherwise noted, values are for VCC=12 V, TA=+25C, and according to Figure 1. Figure 5. V5p0 Power On with 1.6 A Load Figure 6. V3p3 Power On with 3 A Load Figure 7. V5p0 Power On with 15 A Load Figure 8. V3p3 Power On with 8 A Load Figure 9. V5p0 Power Off with 15 A Load Figure 10. V3p3 Power Off with 8 A Load (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 SG1577 -- Dual Synchronous DC/DC Controller Typical Performance Characteristics www.fairchildsemi.com 7 Unless otherwise noted, values are for VCC=12 V, TA=+25C, and according to Figure 1. Figure 11. 3p3 and V5p0 Phase Shift with Light Load Figure 12. V3p3 and V5p0 Phase Shift with Heavy Load Figure 13. Dead Time with Light Load (Rise Edge) Figure 14. Dead Time with Light Load (Fall Edge) Figure 15. Dead Time with Heavy Load (Rise Edge) Figure 16. Dead Time with Heavy Load (Fall Edge) (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 SG1577 -- Dual Synchronous DC/DC Controller Typical Performance Characteristics (Continued) www.fairchildsemi.com 8 Unless otherwise noted, values are for VCC=12 V, TA=+25C, and according to Figure 1. Figure 17. Load Transient Response (Step-Up) 20k /22 nF in Compensation Loop Figure 18. Load Transient Response (Step-Down) 20 k/22 nF in Compensation Loop Figure 19. Over-Current Protection (OCP) Figure 20. Over-Current Protection (Hiccup Mode) SG1577 -- Dual Synchronous DC/DC Controller Typical Performance Characteristics (Continued) 150 Iocset 1 Iocset 2 140 Iocset (uA) 130 120 110 100 90 -40 -25 -10 5 20 35 50 65 80 95 Temperature (oC) Figure 21. Over-Voltage Protection (OVP) (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 Figure 22. IOCSET vs. Temperature www.fairchildsemi.com 9 The SG1577 is a dual-channel voltage-mode PWM controller. It has two sets of synchronous MOSFET driving circuits. The two channels are running 180degrees out of phase. The following descriptions highlight the advantages of the SG1577 design. Prevent CLN Noise in SG1577 To prevent noise/spike on CLN from affecting OCP judgment, SG1577 internal has a 500 ns blanking time to filter out this noise/spike on CLN at each turn-on cycle and counts for eight cycles of CLP>CLN, then OCP is asserted. Soft-Start An internal startup current (10 A) flows out of SS/EN pin to charge an external capacitor. During the startup sequence, SG1577 isn't enabled until the SS/ENB pin is higher than 1.2 V. From 1.2 V to (1.2 + 1.6 x DON / DON_MAX) V, PWM duty cycle gradually increases following SS/ENB pin voltage to bring output rising. After (1.2 + 1.6 x DON / DON_MAX) V, the soft-start period ends and SS/ENB pin continually goes up to 4.8 V. When input power is abnormal, the external capacitor on SS pin is shorted to ground and the chip is disabled. TSOFTSTART = CSS/ENB x 1.6 x DON / DON_MAX / ISOURCE VOFFSET of OCP Comparator 240 220 200 V OFFSET (mV) 180 160 140 120 100 80 60 40 20 0 (1) 4 6 8 10 12 14 16 VCC (V) Over-Current Protection (OCP) Figure 23. VOFFSET1/2 vs. VCC Over-current protection is implemented by sensing the voltage drop across the drain and the source of external high-side MOSFET. Over-current protection is triggered when the voltage drop on external high-side MOSFET's RDS(ON) is greater than the programmable current limit voltage threshold. 120 A flowing through an external resistor between input voltage and the CLP pin sets the threshold of current limit voltage. When over-current condition is true, the system is protected against the cycle-by-cycle current limit. A counter counts a series of over-current peak values to eight cycles; the soft-start capacitor is discharged by a 1 A current until the voltage on SS pin reaches 1.2 V. During the discharge period, the high-side driver is turned off and the low-side driver is turned on. Once the voltage on SS/ENB pin is under 1.2 V, the normal soft-start sequence is initiated and the 10 A current charges the soft-start capacitor again. IL(OCP)= [(RSENSE x IOCSET + VOFFSET) / RDS(ON) (VIN - VOUT) x VOUT / (fOSC x LOUT x VIN x 2) ] SG1577 -- Dual Synchronous DC/DC Controller Functional Description Error Amplifier The IN1 and IN2 pins are connected to the corresponding internal error amplifier's inverting input and the outputs of the error amplifiers are connected to the corresponding COMP1 and COMP2 pins. The COMP1 and COMP2 pins are available for control-loop compensation externally. Non-inverting inputs are internally tied to a fixed 0.7 V 1.5% reference voltage. Oscillator Operation The SG1577 has a frequency-programmable oscillator. The oscillator is running at 60 kHz when the RT pin is floating. The oscillator frequency can be adjusted from 60 kHz up to 320 kHz by an external resistor RRT between RT pin and the ground. The oscillator generates a sawtooth wave that has 90% rising duty. Sawtooth wave voltage threshold is from 1.2 V to 2.8 V. The frequency of oscillator can be programmed by the following equation: (2) where, VOFFSET (=10 mV) is the offset voltage contributed by the internal OCP comparator. fOSC, RT(kHz) = 60kHz + 8522 / RRT(k) Design Notes VCC noise/spike affects the offset voltage of the OCP comparator Figure 23 shows the VOFFSET1/2 vs. VCC variation curve, which is a simulation result by IC internal circuitry. Calculate the OCP variation between VCC=12 V and VCC=4 V. For Ch1 or Ch2, VOFFSET / RDS(ON) = 172 mV / 9 m = 19 A is affected. VCC>10 V is the recommended range; lower, and the comparator's offset voltage is large. (3) Output Driver The high-side gate drivers need an external bootstrapping circuit to provide the required boost voltage. The highest gate driver's output (15 V is the allowed) on high-side and low-side MOSFETs forces external MOSFETs to have the lowest RDS(ON), which results in higher efficiency. Over-Temperature Protection (OTP) The device is over-temperature protected. When chip temperature is over 150C, the chip enters tri-state (high-side driver is turned off). The hysteresis is 20C. (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 www.fairchildsemi.com 10 2. Compensation Frequency Equations The compensation network consists of the error amplifier and the impedance networks ZC and Zf, as Figure 24 shows. SG1577 is a voltage-mode controller; the control loop is a single voltage feedback path, including an error amplifier and PWM comparator, as shown in Figure 24. To achieve fast transient response and accurate output regulation, an adequate compensator design is necessary. A stable control loop has a 0 dB gain crossing with -20 dB/decade slope and a phase margin greater than 45. Figure 25. Compensation Loop fP1 = 0 Figure 24. Closed Loop 1 2 x L O x C O 1 2 x R2 x C2 fP2 = 1 2 x R 2 x (C1 // C2 ) (6) Figure 26 shows the DC-DC converter gain vs. frequency. The compensation gain uses external impedance networks ZC and Zf to provide a stable, high-bandwidth loop. 1. Modulator Frequency Equations The modulator transfer function is the small-signal transfer function of VOUT/VE/A. This transfer function is dominated by a DC gain and the output filter (LO and CO) with a double-pole frequency at fLC and a zero at FESR. The DC gain of the modulator is the input voltage (VIN) divided by the peak-to-peak oscillator voltage VRAMP(=1.6 V). The first step is to calculate the complex conjugate poles contributed by the LC output filter. The output LC filter introduces a double pole, -40 dB / decade gain slope above its corner resonant frequency, and a total phase lag of 180. The resonant frequency of the LC filter expressed as: fP(LC) = fZ1 = SG1577 -- Dual Synchronous DC/DC Controller Type II Compensation Design (for Output Capacitors with High ESR) High crossover frequency is desirable for fast transient response, but often jeopardizes the system stability. To cancel one of the LC filter poles, place the zero before the LC filter resonant frequency. Place the zero at 75% of the LC filter resonant frequency. Crossover frequency should be higher than the ESR zero, but less than 1/5 of the switching frequency. The second pole should be placed at half the switching frequency. (4) The next step of compensation design is to calculate the ESR zero. The ESR zero is contributed by the ESR associated with the output capacitance. Note that this requires that the output capacitor should have enough ESR to satisfy stability requirements. The ESR zero of the output capacitor is expressed as: fZ(ESR ) = 1 2 x C O x ESR (5) Figure 26. Bode Plot (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 www.fairchildsemi.com 11 components close to their pins with a local, clear GND connection or directly to the ground plane. Layout is important in high-frequency switching converter design. If designed improperly, PCB can radiate excessive noise and contribute to converter instability. Place the PWM power stage components first. Mount all the power components and connections in the top layer with wide copper areas. The MOSFETs of buck, inductor, and output capacitor should be as close to each other as possible to reduce the radiation of EMI due to the high-frequency current loop. If the output capacitors are placed in parallel to reduce the ESR of capacitor, equal sharing ripple current should be considered. Place the input capacitor near the drain of high-side MOSFET. In multi-layer PCB, use one layer as power ground and have a separate control signal ground as the reference for all signals. To avoid the signal ground being affected by noise and have best load regulation, it should be connected to the ground terminal of output. A two-layer printed circuit board is recommended. 2 Use the bottom layer of the PCB as a ground plane and make all critical component ground connections through vias to this layer. 3 Keep the metal running from the CLNx terminal to the output inductor short. 4 Use copper-filled polygons on the top (and bottom, if two-layer PCB) circuit layers for the CLN node. 5 6 8 The resistor on the RT pin should be near this pin and the GND return should be short and kept away from the noisy MOSFET's GND (which is short together with IC's PGND pin to GND plane on back side of PCB). 9 Place the compensation components close to the INx and COMPx pins. 11 Minimize the length of the connections between the input capacitors, CIN, and the power switchers (MOSFETs) by placing them nearby. 12 Position both the ceramic and bulk input capacitors as close to the upper MOSFET drain as possible and make the GND returns (from the source of lower MOSFET to VIN capacitor GND) short. 13 Position the output inductor and output capacitors between the upper MOSFET and lower MOSFET and the load. 14 AGND should be on the clearer plane and kept away from the noisy MOSFET GND. The small-signal wiring traces from the DLx and DHx pins to the MOSFET gates should be kept short and wide enough to easily handle the several amps of drive current. 15 PGND should be short, together with MOSFET GND, then through vias to GND plane on the bottom of PCB. The critical, small-signal components include any bypass capacitors (SMD-type of capacitors applied at VCC and SSx/ENB pins), feedback components (resistor divider), and compensation components (between INx and COMPx pins). Position those (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 Place the bootstrap capacitor near the BSTx and CLNx pins. 10 The feedback resistors for both regulators should be located as close as possible to the relevant INx pin with vias tied straight to the ground plane as required. Follow the below guidelines for best performance: 1 7 SG1577 -- Dual Synchronous DC/DC Controller Layout Considerations 16 Prevent spike happen on CLN pin a proper snubber circuit for CLN and GND is recommend. www.fairchildsemi.com 12 12.800.20 A 11.930 11.430 11.430 20 11 B 7.500.10 10.922 10.325 8.422 1 PIN ONE INDICATOR 10 0.51 0.35 0.25 1.27 M 0.50 TYP 1.25 TYP 1.27 TYP C B A LAND PATTERN RECOMMENDATION SEE DETAIL A 2.65 MAX 0.33 0.20 C SG1577 -- Dual Synchronous DC/DC Controller Physical Dimensions 0.10 C 0.200.10 SEATING PLANE PIN#1 IDENTIFICATION OPTIONS 0.75 0.25 X 45 20 20 20 (R0.10) GAGE PLANE (R0.10) 0.25 8 0 SEATING PLANE 0.40~1.27 (1.40) DETAIL A PIN #1 INDICATOR SCALE: 2:1 1 NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE CONFORMS TO JEDEC MS-013. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE MOLD FLASH OR BURRS. D) LANDPATTERN RECOMMENDATION IS FSC DESIGN E) FILENAME AND REVISION: M20BREV4 PIN #1 INDICATOR OPTION 1 HALF MOON & PIN 1 1 OPTION 2 HALF MOON ONLY PIN #1 INDICATOR 1 OPTION 3 PIN 1 ONLY Figure 27. 20-Lead, Small Outline Package (SOP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 www.fairchildsemi.com 13 SG1577 -- Dual Synchronous DC/DC Controller (c) 2009 Fairchild Semiconductor Corporation SG1577 * Rev. 1.0.6 www.fairchildsemi.com 14