DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 14-BIT 2.4-GSPS DIGITAL-TO-ANALOG CONVERTER FEATURES 1 * 14-Bit Resolution * 2.4-GSPS Maximum Update Rate Digital to Analog Converter * Dual Differential Input Ports - Even/Odd Demultiplexed Data - Maximum 1.2 GSPS Each Port, 2.4 GSPS Total - Dual 14-Bit Inputs + 1 Reference Bit - DDR Output Clock - DLL Optimized Clock Timing Synchronized to Reference Bit - LVDS and HyperTransportTM Voltage Level Compatible - Internal 100- Terminations for Data and Reference Bit Inputs * Selectable 2 Times Interpolation With Fs/2 Mixing * 2 * * * * * * Differential Scalable Current Outputs: 5 mA to 30 mA On-Chip 1.2-V Reference 3.3-V Analog Supply Operation Power Dissipation: 2 W 192-Ball CBGA (GEM) Package QML-V Qualified, SMD 5962-07247 Military Temperature Range (-55C to 125C Tcase ) APPLICATIONS * * * * * Cable Modem Termination System Direct Synthesis Cellular Base Transceiver Station Transmit Channels - CDMA: W-CDMA, CDMA2000, TD-SCDMA - 800 to 900-MHz Direct Synthesis Point-to-Point Microwave Radar Satellite Communications DESCRIPTION The DAC5670 is a 14-bit 2.4-GSPS digital-to-analog converter (DAC) with dual demultiplexed differential input ports. The DAC5670 is clocked at the DAC sample rate and the two input ports run at a maximum of 1.2 GSPS. An additional reference bit input sequence is used to adjust the output clock delay to the data source, optimizing the internal data latching clock relative to this reference bit with a delay lock loop (DLL). The DAC5670 also can accept data up to 1.2 GSPS on one input port the same clock configuration. In the single port mode, repeating the input sample (A_ONLY mode), 2 times interpolation by zero stuff (A_ONLY_ZS mode), or 2 times interpolation by repeating and inverting the input sample (A_ONLY_INV) are used to double the input sample rate up to 2.4 GSPS. The DAC5670 operates with a single 3-V to 3.6-V supply voltage. Power dissipation is 2 W at maximum operating conditions. The DAC5670 provides a nominal full-scale differential current-output of 20 mA, supporting both single-ended and differential applications. An on-chip 1.2-V temperature-compensated bandgap reference and control amplifier allows the user to adjust the full-scale output current from the nominal 20 mA to as low as 5 mA or as high as 30 mA. The output current can be directly fed to the load with no additional external output buffer required. The device has been specifically designed for a differential transformer coupled output with a 50- doubly-terminated load. The DAC5670 is available in a 192-ball CBGA package. The device is characterized for operation over the military temperature range ( -55C to 125C Tcase). 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2009, Texas Instruments Incorporated DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com AVAILABLE OPTIONS PACKAGE (1) TOP SIDE SYMBOL -55C to 125C Tcase 192-GEM 5962-0724701VXA DAC5670MGEM-V A_ONLY_ZS A_ONLY A_ONLY_INV For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. NORMAL (1) TEMPERATURE SLEEP Mode Controls CSBIAS CSBIAS_IN 100 DA_P[13:0] DA_N[13:0] Input Registers 100 DB_P[13:0] IOUT_P 14 bit 2.4Gsps DAC Demux and Format IOUT_N DB_N[13:0] RBIASOUT RBIASIN 100 DTCLK_P DTCLK_N Phase Detector Loop Filter REFIO_IN Bandgap Ref LOCK REFIO RESTART /2 /2 INV_CLK DLYCLK_P DACCLK_P LVDS_HTB DACCLK_N Variable Delay DLYCLK_N Figure 1. Functional Block Diagram DAC5670 2 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 Table 1. Terminal Assignments (Top View) 1 A 2 3 4 5 6 7 8 9 10 11 12 13 DB10_N DB10_P DB12_P DB12_N DLYCLK _N DLYCLK _P DTCLK_N DTCLK_P DA2_N DA2_P DA3_N DA3_P 14 B DB9_P GND GND DB11_P DB11_N DB13_N DB13_P DA0_P DA0_N DA1_P DA1_N GND GND DA4_P C DB9_N DB8_P AVDD AVDD AVDD GND GND GND GND AVDD DA7_N DA7_P DA5_P DA4_N D DB7_N DB8_N DB6_P DB6_N AVDD AVDD AVDD AVDD AVDD AVDD DA6_N DA6_P DA5_N DA8_N E DB7_P DB5_N AVDD AVDD GND GND GND GND GND GND AVDD AVDD DA9_N DA8_P F DB3_N DB5_P GND AVDD GND GND GND GND GND GND AVDD GND DA9_P DA10_N G DB3_P AVDD GND AVDD GND GND AVDD AVDD GND GND AVDD GND DA11_N DA10_P H DB4_N AVDD GND AVDD GND GND AVDD AVDD GND GND AVDD GND DA11_P DA12_N J DB4_P DB2_P GND AVDD GND GND GND GND GND GND AVDD GND DA13_P DA12_P K DB1_P DB2_N AVDD AVDD GND GND GND GND GND GND AVDD AVDD DA13_N Dacclk_P L DB1_N AVDD REFIO REFIO_I N AVDD AVDD AVDD AVDD AVDD AVDD GND Inv_clk AVDD Dacclk_N M DB0_P GND AVDD AVDD AVDD IOUT_N IOUT_P GND GND AVDD GND Restart GND GND N DB0_N GND GND AVDD GND GND GND GND GND A_only A_only_z GND CSCap _IN CSCap RBIAS_IN RBIAS _OUT GND GND LVDS _htb AVDD B C D E F G H J K L M N DB9_P DB9_N DB7_N DB7_P DB3_N DB3_P DB4_N DB4_P DB1_P DB1_N DB0_P DB0_N GND DB8_P DB8_N DB5_N DB5_P AVDD AVDD DB2_P DB2_N AVDD GND GND P Sleep A_only _inv M _Normal Table 2. Terminal Assignments (Bottom View) A 1 P 2 DB10_N 3 DB10_P GND AVDD DB6_P AVDD GND GND GND GND AVDD REFIO AVDD GND CSCap 4 DB12_P DB11_P AVDD DB6_N AVDD AVDD AVDD AVDD AVDD AVDD REFIO_I N AVDD AVDD RBIAS_IN 5 DB12_N DB11_N AVDD AVDD GND GND GND GND GND GND AVDD AVDD GND RBIAS_O UT 6 DLYCLK _N DB13_N GND AVDD GND GND GND GND GND GND AVDD IOUT_N GND 7 DLYCLK _P DB13_P GND AVDD GND GND AVDD AVDD GND GND AVDD IOUT_P GND 8 DTCLK_N DA0_P GND AVDD GND GND AVDD AVDD GND GND AVDD GND GND GND 9 DTCLK_P DA0_N GND AVDD GND GND GND GND GND GND AVDD GND GND LVDS_htb 10 DA2_N DA1_P AVDD AVDD GND GND GND GND GND GND AVDD AVDD A_only AVDD 11 DA2_P DA1_N DA7_N DA6_N AVDD AVDD AVDD AVDD AVDD AVDD GND GND Sleep 12 DA3_N GND DA7_P DA6_P AVDD GND GND GND GND AVDD Inv_clk Restart A_only_in v 13 DA3_P GND DA5_P DA5_N DA9_N DA9_P DA11_N DA11_P DA13_P DA13_N AVDD GND A_only_z DA4_P DA4_N DA8_N DA8_P DA10_N DA10_P DA12_N DA12_P Dacclk_P Dacclk_N GND GND 14 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP CSCap _IN GND M_Norma l 3 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com TERMINAL FUNCTIONS TERMINAL NAME BALL NO. Type DESCRIPTION DACCLK_P K14 I External clock, sample clock for the DAC DACCLK_N L14 I Complementary external clock, sample clock for the DAC DLYCLK_P A7 O DDR type data clock to data source DLYCLK_N A6 O DDR type data clock to data source complementary signal DTCLK_P A9 I Input data toggling reference bit DTCLK_N A8 I Input data toggling reference bit, complementary signal DA_P[13] J13 I Port A data bit 13 (MSB) DA_N[13] K13 I Port A data bit 13 complement (MSB) DA_P[12] J14 I Port A data bit 12 DA_N[12] H14 I Port A data bit 12 complement DA_P[11] H13 I Port A data bit 11 DA_N[11] G13 I Port A data bit 11 complement DA_P[10] G14 I Port A data bit 10 DA_N[10] F14 I Port A data bit 10 complement DA_P[9] F13 I Port A data bit 9 DA_N[9] E13 I Port A data bit 9 complement DA_P[8] E14 I Port A data bit 8 DA_N[8] D14 I Port A data bit 8 complement DA_P[7] C12 I Port A data bit 7 DA_N[7] C11 I Port A data bit 7 complement DA_P[6] D12 I Port A data bit 6 DA_N[6] D11 I Port A data bit 6 complement DA_P[5] C13 I Port A data bit 5 DA_N[5] D13 I Port A data bit 5 complement DA_P[4] B14 I Port A data bit 4 DA_N[4] C14 I Port A data bit 4 complement DA_P[3] A13 I Port A data bit 3 DA_N[3] A12 I Port A data bit 3 complement DA_P[2] A11 I Port A data bit 2 DA_N[2] A10 I Port A data bit 2 complement DA_P[1] B10 I Port A data bit 1 DA_N[1] B11 I Port A data bit 1 complement DA_P[0] B8 I Port A data bit 0 (LSB) DA_N[0] B9 I Port A data bit 0 complement (LSB) xxx xxx DB_P[13] B7 DB_N[13] B6 I Port B data bit 13 complement (MSB) DB_P[12] A4 I Port B data bit 12 DB_N[12] A5 I Port B data bit 12 complement DB_P[11] B4 I Port B data bit 11 DB_N[11] B5 I Port B data bit 11 complement DB_P[10] A3 I Port B data bit 10 DB_N[10] A2 I Port B data bit 10 complement DB_P[9] B1 I Port B data bit 9 DB_N[9] C1 I Port B data bit 9 complement 4 Port B data bit 13 (MSB) Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 TERMINAL FUNCTIONS (continued) TERMINAL NAME BALL NO. Type DESCRIPTION DB_P[8] C2 I Port B data bit 8 DB_N[8] D2 I Port B data bit 8 complement DB_P[7] E1 I Port B data bit 7 DB_N[7] D1 I Port B data bit 7 complement DB_P[6] D3 I Port B data bit 6 DB_N[6] D4 I Port B data bit 6 complement DB_P[5] F2 I Port B data bit 5 DB_N[5] E2 I Port B data bit 5 complement DB_P[4] J1 I Port B data bit 4 DB_N[4] H1 I Port B data bit 4 complement DB_P[3] G1 I Port B data bit 3 DB_N[3] F1 I Port B data bit 3 complement DB_P[2] J2 I Port B data bit 2 DB_N[2] K2 I Port B data bit 2 complement DB_P[1] K1 I Port B data bit 1 DB_N[1] L1 I Port B data bit 1 complement DB_P[0] M1 I Port B data bit 0 (LSB) DB_N[0] N1 I Port B data bit 0 complement (LSB) IOUT_P M7 O DAC current output. Full scale when all input bits are set 1. IOUT_N M6 O DAC complementary current output. Full scale when all input bits are 0. RBIASOUT P5 O Rbias resistor current output RBIASIN P4 I Rbias resistor sense input CSCAP P3 O Current source bias voltage CSCAP_IN P2 I Current source bias voltage sense input REFIO L3 O Bandgap reference output REFIO_IN L4 I Bandgap reference sense input RESTART M12 I Resets DLL when high. Low for normal DLL operation. LVDS_HTB P9 I DLYCLK_P/N control, lvds mode when high, ht mode when low INV_CLK L12 I Inverts the DLL target clocking relationship when high. Low for normal DLL operation. SLEEP P11 I Active-high sleep NORMAL P13 I High for {a0,b0,a1,b1,a2,b2, ...} normal mode A_ONLY N10 I High for {a0,a0,a1,a1,a2,a2, ...} A_only mode A_ONLY_INV P12 I High for {a0,-a0, a1,-a1,a2,-a2, ...} A_only_inv mode A_ONLY_ZS N13 I High for {a0,0,a1,0,a2,0, ...} A_only_zs mode xxx xxx xxx xxx Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 5 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN Supply voltage AVDD to GND DA_P[13..0], DA_N[13..0], DB_P[13..0], DB_N[13..0] Measured with respect to GND NORMAL, A_ONLY, A_ONLY_INV, A_ONLY_ZS MAX UNIT 5.0 V -0.3 AVDD + 0.3 V Measured with respect to GND -0.3 AVDD + 0.3 V DTCLK_P, DTCLK_N, DACCLK_P, DACCLK_N Measured with respect to GND -0.3 AVDD + 0.3 V LVDS_HTB, INV_CLK, RESTART Measured with respect to GND -0.3 AVDD + 0.3 V IOUT_P, IOUT_N Measured with respect to GND AVDD - 0.5 AVDD + 1.5 V CSCAP_IN, REFIO_IN, RBIAS_IN Measured with respect to GND -0.3 AVDD + 0.3 V 20 mA -65 150 C Maximum Junction Temperature 150 C Lead temperature 1,6 mm (1/16 in) from the case for 10 s 260 C Peak input current (any input) Storage temperature range (1) 6 Stresses above those listed under "absolute maximum ratings" may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 DC Electrical Characteristics TC,MIN = -55C to TC,MAX = 125C, typical values at 25C, AVDD = 3 V to 3.6 V, IoutFS = 20 mA (unless otherwise noted) PARAMETER TEST CONDITIONS MIN Resolution TYP (1) MAX 14 UNIT Bits DC Accuracy INL Integral nonlinearity DNL Differential nonlinearity TC,MIN to TC,MAX , fDAC = 640 KHz, fOUT = 10 KHz Monotonocity -7.5 1.5 7.5 -0.98 0.8 1.75 14 LSB Bits Analog Output Offset error Mid code offset -0.45 0.09 0.45 %FSR Gain error With external reference -6.0 1.6 6.0 %FSR Gain error With internal reference -6.0 1.6 6.0 %FSR 30 mA Full-scale output current Output compliance range IO(FS) = 20 mA, AVDD = 3.15 V to 3.45 V AVDD - 0.5 Output resistance Output capacitance IOUT_P and IOUT_N single ended AVDD + 0.5 V 300 (2) k 13.7 (2) pF Reference Output Reference voltage 1.14 Reference output current 1.2 1.26 V 100 nA Reference Input VREFIO Input voltage range 1.14 1.2 1.26 (2) Input resistance 1 Small-signal bandwidth 1.4 V M MHz 3.2 (2) Input capacitance pF Temperature Coefficients Offset drift 75 ppm of FSR/C Gain drift With external reference 75 ppm of FSR/C Gain drift With internal reference 75 ppm of FSR/C 35 ppm/C Reference voltage drift Power Supply AVDD Analog supply voltage IAVDD Analog supply current IAVDD 3.3 3.6 V fDAC = 2.4 GHz, NORMAL input mode 560 650 mA Sleep mode, AVDD supply current Sleep mode (SLEEP pin high) 150 180 mA P Power dissipation fDAC = 2.4 GHz, NORMAL input mode 1800 2350 mW PSRR Power-supply rejection ratio AVDD = 3.15V to 3.45V 0.4 1.3 (1) (2) 3 %FSR/V Typicals are characterization values at 25C and AVDD = 3.3V. These parameters are characterized but not production tested. Specified by design Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 7 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com AC Electrical Characteristics TC,MIN = -55C to TC,MAX = 125C, typical values at 25C, AVDD = 3 V to 3.6 V, IoutFS = 20 mA (unless otherwise noted) PARAMETER TEST CONDITIONS TYP (1) MIN MAX UNIT Analog Output fDAC Maximum output update rate ts(DAC) Output setting time to 0.1% tpd Output propagation delay tr(IOUT) Output rise time, 10% to 90% 280 ps tf(IOUT) Output fall time, 90% to 10% 280 ps 2.4 Mid-scale transition GSPS 3.5 ns 7 DACCLK + 1.5 ns AC Performance fDAC = 2.4 GSPS, fOUT = 100 MHz, Dual-port mode, 0 dBFS 46 fDAC = 2.4 GSPS, fOUT = 200 MHz, Dual-port mode, 0 dBFS SFDR Spurious-free dynamic range 51 fDAC = 2.4 GSPS, fOUT = 300 MHz, Dual-port mode, 0 dBFS 31 36 fDAC = 2.4 GSPS, fOUT = 500 MHz, Dual-port mode, 0 dBFS 35 43 fDAC = 2.4 GSPS, fOUT = 500 MHz, Dual-port mode, -6 dBFS fDAC = 2.4 GSPS, fOUT = 100 MHz, Dual-port mode, 0 dBFS Signal-to-noise ratio 58 60 56 62 fDAC = 2.4 GSPS, fOUT = 500 MHz, Dual-port mode, 0 dBFS 51 58 fDAC = 2.4 GSPS, fOUT = 500 MHz, Dual-port mode, -6 dBFS IMD3 IMD (1) 8 Total harmonic distortion Third-order two-tone intermodulation dBc 52 45 fDAC = 2.4 GSPS, fOUT = 200 MHz, Dual-port mode, 0 dBFS THD 60 fDAC = 2.4 GSPS, fOUT = 300 MHz, Dual-port mode, 0 dBFS fDAC = 2.4 GSPS, fOUT = 100 MHz, Dual-port mode, 0 dBFS dBc 47 fDAC = 2.4 GSPS, fOUT = 200 MHz, Dual-port mode, 0 dBFS SNR 55 52 50 fDAC = 2.4 GSPS, fOUT = 300 MHz, Dual-port mode, 0 dBFS 31 36 fDAC = 2.4 GSPS, fOUT = 500 MHz, Dual-port mode, 0 dBFS 35 46 dBc fDAC = 2.4 GSPS, fOUT = 500 MHz, Dual-port mode, -6 dBFS 44 fDAC = 2.4 GSPS, fOUT = 99 MHz and 102 MHz, Each tone at -6 dBFS, Dual-port mode. 70 dBc fDAC = 2.4 GSPS, fOUT = 200 MHz and 202 MHz, Each tone at -6 dBFS, Dual-port mode. 68 dBc fDAC = 2.4 GSPS, fOUT = 253 Mhz and 257 MHz, Each tone at -6 dBFS, Dual-port mode. 47 57 dBc fDAC = 2.4 GSPS, fOUT = 299 Mhz and 302 MHz, Each tone at -6 dBFS, Dual-port mode. 35 55 dBc 47 62.5 dBc fDAC = 2.4 GSPS, fOUT = 298 MHz, 299 MHz, Four-tone intermodulation 300 MHz, and 301 MHz, Each tone at -12 dBFS, Dual-port mode. Typicals are characterization values at 25C and AVDD = 3.3V. These parameters are characterized but not production tested Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 Digital Electrical Characteristics TC,MIN = -55C to TC,MAX = 125C, typical values at 25C, AVDD = 3 V to 3.6 V, IoutFS = 20 mA (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT CMOS Interface (SLEEP, RESTART, INV_CLK, NORMAL, A_ONLY, A_ONLY_INV, A_ONLY_ZS) VIH High-level input voltage 2 VIL Low-level input voltage 0 IIH High-level input current IIL Low-level input current -10 Input capacitance 3 V 0 0.8 V 0.2 10 A -0.2 A (2) pF 2.5 Differential Data Interface (DA_P[13:0], DA_N[13:0], DB_P[13:0], DB_N[13:0], DTCLK_P, DTCLK_N) VITH Differential input threshold -100 ZT Internal termination impedance 80 VICOM Input common mode 0.6 Ci Input capacitance 100 100 mV 125 1.4 V 2.6 (2) pF Clock Inputs (DACCLK_P, DACCLK_N) |DACCLK_P DACCLK_N| VCLKCM (1) (2) Clock differential input voltage 200 1000 mV Clock duty cycle 40 60 % Clock common mode 1.0 1.4 V Typicals are characterization values at 25C and AVDD = 3.3V. These parameters are characterized but not production tested Specified by design Thermal Information Parameter TEST CONDITIONS TYPICAL UNIT RJA Junction-to-free-air thermal resistance Non-thermally enhanced JEDEC standard PCB, per JESD-51, 51-3 41.3 C/W RJC Junction-to-case thermal resistance MIL-STD-883 test method 1012 3.8 C/W Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 9 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com Estimated Life (Years) 100 Electromigration Fail Mode 10 1 100 110 120 130 140 150 160 Continuous TJ (C) A. See data sheet for absolute maximum and minimum recommended operating conditions. B. Silicon operating life design goal is 10 years at 105C junction temperture (does not include package interconnect life). Figure 2. DAC5670MGEM-V - 192/GEM Package Operating LIfe Derating Chart 10 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 TYPICAL CHARACTERISTICS Single-Tone Spectrum Power vs Frequency Figure 3. Two-Tone IMD (Power) vs Frequency Figure 4. Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 11 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (continued) W-CDMA TM1 Single Carrier Power vs Frequency Figure 5. W-CDMA TM1 Single Carrier Power vs Frequency Figure 6. 12 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 TYPICAL CHARACTERISTICS (continued) W-CDMA TM1 Dual Carrier Power vs Frequency Figure 7. W-CDMA TM1 Three Carrier Power vs Frequency Figure 8. Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 13 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (continued) W-CDMA TM1 Four Carrier Power vs Frequency Figure 9. 14 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 APPLICATION INFORMATION Detailed Description Figure 10 shows a simplified block diagram of the current steering DAC5670. The DAC5670 consists of a segmented array of NPN-transistor current sinks, capable of delivering a full-scale output current up to 30mA. Differential current switches direct the current of each current sink to either one of the complementary output nodes IOUT_P or IOUT_N. The complementary current output enables differential operation, canceling out common-mode noise sources (digital feed-through, on-chip and PCB noise), dc offsets, and even-order distortion components, and doubling signal output power. The full-scale output current is set using an external resistor (RBIAS) in combination with an on-chip bandgap voltage reference source (1.2V) and control amplifier. The current (IBIAS) through resistor RBIAS is mirrored internally to provide a full-scale output current equal to 32 times IBIAS. The full-scale current is adjustable from 30mA down to 5mA by using the appropriate bias resistor value. Figure 10. Current Steering DAC5670 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 15 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com Digital Inputs The DAC5670 differential digital inputs are compatible with LVDS and HyperTransport voltage levels. Figure 11. Digital Input Voltage Options The DAC5670 uses low voltage differential signaling (LVDS and Hyper-Transport) for the bus input interface. The LVDS and Hyper-Transport input modes feature a low differential voltage swing. The differential characteristic of LVDS and Hyper-Transport modes allow for high-speed data transmission with low electromagnetic interference (EMI) levels. Figure 12 shows the equivalent complementary digital input interface for the DAC5670, valid for pins DA_P[13:0], DA_N[13:0], DB_P[13:0], and DB_N[13:0]. Figure 12. 16 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 Figure 13 shows a schematic of the equivalent CMOS/TTL-compatible digital inputs of the DAC5670, valid for the following pins: RESTART, LVDS_HTB, INV_CLK, SLEEP, NORMAL, A_ONLY, A_ONLY_INV, and A_ONLY_ZS. Figure 13. The DAC5670 is clocked at the DAC sample rate. Each input port runs at a maximum of 1.2 GSPS. The DAC5670 provides an output clock at one-half the input port data rate (DACCLK/4), monitors an additional reference bit input sequence, and adjusts the output clock delay to optimize the data latch relative to the reference bit with a DLL. The DLL delay automatically adjusts for drift over temperature and time. Data Source DAC5670 DA_P[13:0] DA_N[13:0] Input Registers DB_P[13:0] DB_N[13:0] DTCLK_P DTCLK_N Delay Locked Loop (DLL) /2 /2 DLYCLK_P DLYCLK_N DACCLK_P DACCLK_N Figure 14. DLL Input Loop Simplified Block Diagram Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 17 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com DACCLK_P/N This internal DACCLK/2 is used to clock the input data DA and DB into the DAC5670 DACCLK/2 internal to DAC5670 DLYCLK is DACCLK/4 delayed by the DAC5670 DLL to be used as the DDR clock for the data source digital chip DLYCLK_P/N source digital chip's clock to data output time DTCLK_P/N DTCLK is a toggling bit, aligned with DA and DB data from digita l chip, used by the DAC5670 DLL feedback path DA_P/N[13:0] a0 a1 a2 a3 DB_P/N[13:0] b0 b1 b2 b3 internal data to the DAC core in NORMAL mode a0 b0 a1 b1 TBD pipeline delay Figure 15. DLL Input Loop Functional Timing Input Format The DAC5670 has four input modes selected by the four mutually exclusive configuration pins: NORMAL, A_ONLY, A_ONLY_INV, and A_ONLY_ZS. Table 3 lists the input modes, the input sample rates, the maximum DAC sample rate (CLK input) and resulting DAC output sequence for each configuration. For all configurations, the DLYCLK_P/N outputs and DTCLK_P/N inputs are DACCLK_P/N frequency divided by four. Table 3. DAC5670 Input Formats DLYCLK_P/N AND DTCLK_P/N FREQ (MHz) NORMAL A_ONLY A_ONLY_INV A_ONLY_ZS FinA/Fdac FinB/Fdac fDAC MAX (MHz) 1 0 0 0 1/2 1/2 2400 Fdac/4 A0, B0, A1, B1, A2, B2, . . . 0 1 0 0 1/2 Off 2400 Fdac/4 A0, A0, A1, A1, A2, A2, . . . 0 0 1 0 1/2 Off 2400 Fdac/4 A0, -A0, A1, -A1, A2, -A2, . . 0 0 0 1 1/2 Off 2400 Fdac/4 A0, 0, A1, 0, A2, 0, . . . 18 Submit Documentation Feedback DAC OUTPUT SEQUENCE Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 Clock Input The DAC5670 features differential, LVPECL compatible clock inputs (DACCLK_P, DACCLK_N). Figure 16shows the equivalent schematic of the clock input buffer. The internal biasing resistors set the input common-mode voltage to AVDD/2, while the input resistance is typically 1 k. A variety of clock sources can be ac-coupled to the device, including a sine wave source (see Figure 17). Figure 16. Clock Equivalent Input Figure 17. Driving the DAC5670 with a Single-Ended Clock Source Using a Transformer To obtain best ac performance the DAC5670 clock input should be driven with a differential LVPECL or sine wave source as shown in Figure 18and Figure 19. Here, the potential of VTT should be set to the termination voltage required by the driver along with the proper termination resistors (RT). The DAC5670 clock input can also be driven single-ended for slower clock rates using TTL/CMOS levels; this is shown in Figure 20. Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 19 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com Figure 18. Driving the DAC5670 with a Single-Ended ECL/PECL Clock Source Figure 19. Driving the DAC5670 with a Differential ECL/PECL Clock Source Figure 20. Driving the DAC5670 with a Single-Ended TTL/CMOS Clock Source 20 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 DAC Transfer Function The DAC5670 has a current sink output. The current flow through IOUT_P and IOUT_N is controlled by Dx_P[13:0] and Dx_N[13:0]. For ease of use, we denote D[13:0] as the logical bit equivalent of Dx_P[13:0] and its complement Dx_N[13:0]. The DAC5670 supports straight binary coding with D13 being the MSB and D0 the LSB. Full-scale current flows through IOUTP when all D[13:0] inputs are set high and through IOUTN when all D[13:0] inputs are set low. The relationship between IOUT_P and IOUT_N can be expressed as Equation 1: IOUT_N = IO(FS) - IOUT_P (1) IO(FS) is the full-scale output current sink (5 mA to 30 mA). Since the output stage is a current sink, the current can only flow from AVDD through the load resistors RL into the IOUT_N and IOUT_P pins. The output current flow in each pin driving a resistive load can be expressed as shown in Figure 21, as well as in Equation 2 and Equation 3. Figure 21. Relationship between D[13:0], IOUT_N and IOUT_P IOUT_N = (IOUT(FS) x (16383 - CODE)) / 16384 (2) IOUT_P = (IOUT(FS) x CODE) / 16384 (3) where CODE is the decimal representation of the DAC input word. This would translate into single-ended voltages at IOUT_N and IOUT_P, as shown in Equation 4 and Equation 5: VOUTN = AVDD - IOUT_N x RL (4) VOUTP = AVDD - IOUT_P x RL (5) For example, assuming that D[13:0] = 1 and that RL is 50 , the differential voltage between pins IOUT_N and IOUT_P can be expressed as shown in Equation 6 through Equation 8 where IO(FS) = 20 mA: VOUTN = 3.3 V - 0 mA x 50 = 3.3 V (6) VOUTP = 3.3 V - 20 mA x 50 = 2.3 V (7) VDIFF = VOUTN - VOUTP = 1 V (8) If D[13:0] = 0, then IOUT_P = 0 mA and IOUT_N = 20 mA and the differential voltage VDIFF = -1 V. The output currents and voltages in IOUT_N and IOUT_P are complementary. The voltage, when measured differentially, will be doubled compared to measuring each output individually. Care must be taken not to exceed the compliance voltages at the IOUT_N and IOUT_P pins in order to keep signal distortion low. Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 21 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com Reference Operation Bandgap Reference 1.2 V Reference REFIO REFIO_IN External REFIO Filter Capacitor + RBIASOUT RBIASIN External RBIAS Resistor Figure 22. Reference Circuit The DAC5670 comprises a bandgap reference and control amplifier for biasing the full-scale output current. The full-scale output current is set by applying an external resistor RBIAS to pins RBIASOUT and RBIASIN. The bias current IBIAS through resistor RBIAS is defined by the on-chip bandgap reference voltage and control amplifier. The full-scale output current equals 32 times this bias current. The full-scale output current IOUTFS can thus be expressed as: IOUTFS = 32 x IBIAS = 32 x VREFIO/RBIAS (9) Where: VREFIO Voltage at terminals REFIO and REFIO_IN The bandgap reference voltage delivers an accurate voltage of 1.2 V. An external REFIO filter capacitor of 0.1 F should be connected externally to the terminals REFIO and REFIO_IN for compensation. The full-scale output current can be adjusted from 30 mA down to 5 mA by varying external resistor RBIAS . 22 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 Analog Current Outputs Figure 23 is a simplified schematic of the current sink array output with corresponding switches. Differential NPN switches direct the current of each individual NPN current sink to either the positive output node IOUT_P or its complementary negative output node IOUT_N. The input data presented at the DA_P[13:0], DA_N[13:0], DB_P[13:0] and DB_N[13:0] is decoded to control the sw_p(N) and sw_n(N) current switches. AVDD (3.3 V) RLOAD RLOAD IOUT_N sw_p(0) IOUT_P sw_n(0) sw_p(1) sw_n(1) sw_p(N) sw_n(N) Current Sink Array CSBIAS CSBIAS_IN External CSBIAS Filter Capacitor Figure 23. Current Sink Array The external output resistors RLOAD are connected to the positive supply, AVDD. The DAC5670 can easily be configured to drive a doubly-terminated 50 cable using a properly selected transformer. Figure 24 and Figure 25 show the 1:1 and 4:1 impedance ratio configuration, respectively. These configurations provide maximum rejection of common-mode noise sources and even-order distortion components, thereby doubling the power of the DAC to the output. The center tap on the primary side of the transformer is terminated to AVDD, enabling a dc current flow for both IOUT_N and IOUT_P. Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 23 DAC5670-SP SGLS386 - JANUARY 2009............................................................................................................................................................................................... www.ti.com Figure 24. Figure 25. Sleep Mode When the SLEEP pin is asserted (high), the DAC5670 enters a lower-power mode. 24 Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP DAC5670-SP www.ti.com............................................................................................................................................................................................... SGLS386 - JANUARY 2009 Definitions of Specifications and Terminology Differential Nonlinearity (DNL): Defined as the variation in analog output associated with an ideal 1 LSB change in the digital input code. Gain Drift: Defined as the maximum change in gain, in terms of ppm of full-scale range (FSR) per C, from the value at 25C to values over the full operating temperature range. Gain Error: Defined as the percentage error in the ratio between the measured full-scale output current and the value of the ideal full-scale output (32 x VREFIO/RBIAS). A VREFIO of 1.2V is used to measure the gain error with an external reference voltage applied. With an internal reference, this error includes the deviation of VREFIO (internal bandgap reference voltage) from the typical value of 1.2V. Integral Nonlinearity (INL): Defined as the maximum deviation of the actual analog output from the ideal output, determined by a straight line drawn from zero scale to full scale. Intermodulation Distortion (IMD3, IMD): The two-tone IMD3 or four-tone IMD is defined as the ratio (in dBc) of the worst 3rd-order (or higher) intermodulation distortion product to either fundamental output tone. Offset Drift: Defined as the maximum change in DC offset, in terms of ppm of full-scale range (FSR) per C, from the value at 25C to values over the full operating temperature range. Offset Error: Defined as the percentage error in the ratio of the differential output current (IOUT_P - IOUT_N) to half of the full-scale output current for input code 8192. Output Compliance Range: Defined as the minimum and maximum allowable voltage at the output of the current-output DAC. Exceeding this limit may result in reduced reliability of the device or adversely affecting distortion performance. Power Supply Rejection Ratio (PSSR): Defined as the percentage error in the ratio of the delta IOUT and delta supply voltage normalized with respect to the ideal IOUT current. Reference Voltage Drift: Defined as the maximum change of the reference voltage in ppm per degree Celsius from value at ambient (25C) to values over the full operating temperature range. Spurious Free Dynamic Range (SFDR): Defined as the difference (in dBc) between the peak amplitude of the output signal and the peak spurious signal. Signal to Noise Ratio (SNR): Defined as the ratio of the RMS value of the fundamental output signal to the RMS sum of all other spectral components below the Nyquist frequency, including noise, but excluding the first six harmonics and dc. Total Harmonic Distortion (THD): Defined as the ratio of the rms sum of the first six harmonic components to the rms value of the fundamental output signal. Submit Documentation Feedback Copyright (c) 2009, Texas Instruments Incorporated Product Folder Link(s): DAC5670-SP 25 PACKAGE OPTION ADDENDUM www.ti.com 22-Apr-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing 5962-0724701VXA ACTIVE CBGA GEM Pins Package Eco Plan (2) Qty 192 1 TBD Lead/Ball Finish Call TI MSL Peak Temp (3) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP(R) Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2009, Texas Instruments Incorporated