DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 DS90CR285/DS90CR286 +3.3V Rising Edge Data Strobe LVDS 28-Bit Channel Link-66 MHz Check for Samples: DS90CR285, DS90CR286 FEATURES DESCRIPTION * * The DS90CR285 transmitter converts 28 bits of LVCMOS/LVTTL data into four LVDS (Low Voltage Differential Signaling) data streams. A phase-locked transmit clock is transmitted in parallel with the data streams over a fifth LVDS link. Every cycle of the transmit clock 28 bits of input data are sampled and transmitted. The DS90CR286 receiver converts the LVDS data streams back into 28 bits of LVCMOS/LVTTL data. At a transmit clock frequency of 66 MHz, 28 bits of TTL data are transmitted at a rate of 462 Mbps per LVDS data channel. Using a 66 MHz clock, the data throughput is 1.848 Gbit/s (231 Mbytes/s). 1 2 * * * * * * * * * * * * Single +3.3V Supply Chipset (Tx + Rx) Power Consumption <250 mW (typ) Power-Down Mode (<0.5 mW total) Up to 231 Megabytes/sec Bandwidth Up to 1.848 Gbps Data Throughput Narrow Bus Reduces Cable Size 290 mV Swing LVDS Devices for Low EMI +1V Common Mode Range (Around +1.2V) PLL Requires no External Components Both Devices are Offered in a Low Profile 56Lead TSSOP Package Rising Edge Data Strobe Compatible with TIA/EIA-644 LVDS Standard ESD Rating > 7 kV Operating Temperature: -40C to +85C The multiplexing of the data lines provides a substantial cable reduction. Long distance parallel single-ended buses typically require a ground wire per active signal (and have very limited noise rejection capability). Thus, for a 28-bit wide data and one clock, up to 58 conductors are required. With the Channel Link chipset as few as 11 conductors (4 data pairs, 1 clock pair and a minimum of one ground) are needed. This provides a 80% reduction in required cable width, which provides a system cost savings, reduces connector physical size and cost, and reduces shielding requirements due to the cables' smaller form factor. The 28 LVCMOS/LVTTL inputs can support a variety of signal combinations. For example, seven 4-bit nibbles or three 9-bit (byte + parity) and 1 control. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com Block Diagram Figure 1. DS90CR285 - 56-Lead TSSOP See Package Number DGG0056A Figure 2. DS90CR285 - 56-Lead TSSOP See Package Number DGG0056A Pin Diagrams for TSSOP Packages Figure 3. DS90CR285 See Package Number DGG (R-PDSO-G56) 2 Submit Documentation Feedback Figure 4. DS90CR286 See Package Number DGG (R-PDSO-G56) Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 Typical Application These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) -0.3V to +4V Supply Voltage (VCC) CMOS/TTL Input Voltage -0.3V to (VCC + 0.3V) CMOS/TTL Output Voltage -0.3V to (VCC + 0.3V) LVDS Receiver Input Voltage -0.3V to (VCC + 0.3V) LVDS Driver Output Voltage -0.3V to (VCC + 0.3V) LVDS Output Short Circuit Duration Continuous Junction Temperature +150C Storage Temperature -65C to +150C Lead Temperature (Soldering, 4 sec.) Solder Reflow Temperature +260C Maximum Package Power Dissipation @ +25C DS90CR285MTD 1.63 W DS90CR286MTD 1.61 W Package Derating: DS90CR285MTD 12.5 mW/C above +25C DS90CR286MTD 12.4 mW/C above +25C ESD Rating (HBM, 1.5 k, 100 pF) (1) (2) > 7 kV "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. "Electrical Characteristics" specify conditions for device operation. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. Recommended Operating Conditions Min Nom Max Units Supply Voltage (VCC) 3.0 3.3 3.6 V Operating Free Air Temperature (TA) -40 +25 +85 C Receiver Input Range 0 Supply Noise Voltage (VCC) 2.4 V 100 mVPP Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 3 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified Symbol Parameter Conditions Min Typ Max Unit s LVCMOS/LVTTL DC SPECIFICATIONS VIH High Level Input Voltage 2.0 VCC V VIL Low Level Input Voltage GND 0.8 V VOH High Level Output Voltage IOH = -0.4 mA VOL Low Level Output Voltage IOL = 2 mA 0.06 0.3 V VCL Input Clamp Voltage ICL = -18 mA -0.79 -1.5 V IIN Input Current VIN = VCC, GND, 2.5V or 0.4V 5.1 10 A IOS Output Short Circuit Current VOUT = 0V -60 -120 mA 290 450 mV 35 mV 1.375 V 35 mV -3.5 -5 mA 1 10 A +100 mV 2.7 3.3 V LVDS DRIVER DC SPECIFICATIONS VOD Differential Output Voltage RL = 100 VOD Change in VOD between Complimentary Output States VOS Offset Voltage (1) VOS Change in VOS between Complimentary Output States IOS Output Short Circuit Current VOUT = 0V, RL = 100 IOZ Output TRI-STATE Current PWR DWN = 0V, 250 1.125 1.25 VOUT = 0V or VCC LVDS RECEIVER DC SPECIFICATIONS VTH Differential Input High Threshold VTL Differential Input Low Threshold IIN Input Current VCM = +1.2V -100 mV VIN = +2.4V, VCC = 3.6V 10 A VIN = 0V, VCC = 3.6V 10 A TRANSMITTER SUPPLY CURRENT ICCTW ICCTZ Transmitter Supply Current Worst Case (with Loads) Transmitter Supply Current Power Down RL = 100, CL = 5 pF, Worst Case Pattern (Figure 5 Figure 6) , TA = -10C to +70C f = 32.5 MHz 31 45 mA f = 37.5 MHz 32 50 mA f = 66 MHz 37 55 mA RL = 100, CL = 5 pF, Worst Case Pattern (Figure 5 Figure 6) , TA = -40C to +85C f = 40 MHz 38 51 mA f = 66 MHz 42 55 mA PWR DWN = Low Driver Outputs in TRI-STATE under Powerdown Mode 10 55 A CL = 8 pF, Worst Case Pattern (Figure 5 Figure 7) , TA = -10C to +70C f = 32.5 MHz 49 65 mA f = 37.5 MHz 53 70 mA f = 66 MHz 78 105 mA CL = 8 pF, Worst Case Pattern (Figure 5 Figure 7) , TA = -40C to +85C f = 40 MHz 55 82 mA f = 66 MHz 78 105 mA 10 55 A RECEIVER SUPPLY CURRENT ICCRW ICCRZ (1) 4 Receiver Supply Current Worst Case Receiver Supply Current Power Down PWR DWN = Low Receiver Outputs Stay Low during Powerdown Mode VOS previously referred as VCM. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 Transmitter Switching Characteristics Over recommended operating supply and -40C to +85C ranges unless otherwise specified Symbol Parameter Min Typ Max Units LLHT LVDS Low-to-High Transition Time (Figure 6) 0.5 1.5 ns LHLT LVDS High-to-Low Transition Time (Figure 6) 0.5 1.5 ns TCIT TxCLK IN Transition Time (Figure 8) 5 ns TCCS TxOUT Channel-to-Channel Skew (Figure 9) TPPos0 Transmitter Output Pulse Position for Bit0 (1) (Figure 20) TPPos1 Transmitter Output Pulse Position for Bit1 TPPos2 Transmitter Output Pulse Position for Bit2 6.5 TPPos3 Transmitter Output Pulse Position for Bit3 10.2 TPPos4 Transmitter Output Pulse Position for Bit4 13.7 TPPos5 Transmitter Output Pulse Position for Bit5 TPPos6 Transmitter Output Pulse Position for Bit6 TPPos0 Transmitter Output Pulse Position for Bit0 (2) (Figure 20) TPPos1 TPPos2 250 f = 40 MHz ps -0.4 0 0.4 ns 3.1 3.3 4.0 ns 6.8 7.6 ns 10.4 11.0 ns 13.9 14.6 ns 17.3 17.6 18.2 ns 21.0 21.2 21.8 ns -0.4 0 0.3 ns Transmitter Output Pulse Position for Bit1 1.8 2.2 2.5 ns Transmitter Output Pulse Position for Bit2 4.0 4.4 4.7 ns TPPos3 Transmitter Output Pulse Position for Bit3 6.2 6.6 6.9 ns TPPos4 Transmitter Output Pulse Position for Bit4 8.4 8.8 9.1 ns TPPos5 Transmitter Output Pulse Position for Bit5 10.6 11.0 11.3 ns TPPos6 Transmitter Output Pulse Position for Bit6 12.8 13.2 13.5 ns TCIP TxCLK IN Period (Figure 10 ) 15 T 50 ns TCIH TxCLK IN High Time (Figure 10) 0.35T 0.5T 0.65T ns TCIL TxCLK IN Low Time (Figure 10) 0.35T 0.5T 0.65T ns TSTC TxIN Setup to TxCLK IN (Figure 10) 2.5 THTC TxIN Hold to TxCLK IN (Figure 10) 0 TCCD TxCLK IN to TxCLK OUT Delay @ 25C,VCC=3.3V (Figure 12) 3 TPLLS TPDD (1) (2) f = 66 MHz ns ns 3.7 5.5 ns Transmitter Phase Lock Loop Set (Figure 14) 10 ms Transmitter Powerdown Delay (Figure 18) 100 ns The min. and max. are based on the actual bit position of each of the 7 bits within the LVDS data stream across PVT. The min. and max. limits are based on the worst bit by applying a -400ps/+300ps shift from ideal position. Receiver Switching Characteristics Over recommended operating supply and -40C to +85C ranges unless otherwise specified Symbol Parameter CLHT CMOS/TTL Low-to-High Transition Time (Figure 7) CHLT CMOS/TTL High-to-Low Transition Time (Figure 7) RSPos0 Receiver Input Strobe Position for Bit 0 RSPos1 Receiver Input Strobe Position for Bit 1 RSPos2 Receiver Input Strobe Position for Bit 2 RSPos3 Receiver Input Strobe Position for Bit 3 RSPos4 Receiver Input Strobe Position for Bit 4 RSPos5 RSPos6 (1) Min Typ Max Units 2.2 5.0 ns 2.2 5.0 ns 1.0 1.4 2.15 ns 4.5 5.0 5.8 ns 8.1 8.5 9.15 ns 11.6 11.9 12.6 ns 15.1 15.6 16.3 ns Receiver Input Strobe Position for Bit 5 18.8 19.2 19.9 ns Receiver Input Strobe Position for Bit 6 22.5 22.9 23.6 ns (1) (Figure 21) f = 40 MHz The min. and max. are based on the actual bit position of each of the 7 bits within the LVDS data stream across PVT. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 5 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com Receiver Switching Characteristics (continued) Over recommended operating supply and -40C to +85C ranges unless otherwise specified Symbol Parameter (2) Max Units Receiver Input Strobe Position for Bit 0 0.7 1.1 1.4 ns RSPos1 Receiver Input Strobe Position for Bit 1 2.9 3.3 3.6 ns RSPos2 Receiver Input Strobe Position for Bit 2 5.1 5.5 5.8 ns RSPos3 Receiver Input Strobe Position for Bit 3 7.3 7.7 8.0 ns RSPos4 Receiver Input Strobe Position for Bit 4 9.5 9.9 10.2 ns RSPos5 Receiver Input Strobe Position for Bit 5 11.7 12.1 12.4 ns RSPos6 Receiver Input Strobe Position for Bit 6 13.9 14.3 14.6 ns RxIN Skew Margin (3) (Figure 22) RCOP RxCLK OUT Period (Figure 11) RCOH RxCLK OUT High Time (Figure 11) RCOL RSRC RxCLK OUT Low Time (Figure 11) RxOUT Setup to RxCLK OUT (Figure 11) RHRC RxOUT Hold to RxCLK OUT (Figure 11) RCCD RxCLK IN to RxCLK OUT Delay (Figure 13) f = 66 MHz Typ RSPos0 RSKM (Figure 21) Min f = 40 MHz 490 f = 66 MHz 400 ps ps 15 T 50 ns f = 40 MHz 6.0 10.0 ns f = 66 MHz 4.0 6.1 ns f = 40 MHz 10.0 13.0 ns f = 66 MHz 6.0 7.8 ns f = 40 MHz 6.5 14.0 ns f = 66 MHz 2.5 8.0 ns f = 40 MHz 6.0 8.0 ns f = 66 MHz 2.5 4.0 f = 40 MHz 4.0 6.7 8.0 ns f = 66 MHz 5.0 6.6 9.0 ns ns RPLLS Receiver Phase Lock Loop Set (Figure 15) 10 ms RPDD Receiver Powerdown Delay (Figure 19) 1 s (2) (3) The min. and max. limits are based on the worst bit by applying a -400ps/+300ps shift from ideal position. Receiver Skew Margin is defined as the valid data sampling region at the receiver inputs. This margin takes into account the transmitter pulse positions (min and max) and the receiver input setup and hold time (internal data sampling window). This margin allows LVDS interconnect skew, inter-symbol interference (both dependent on type/length of cable), and clock jitter less than 250 ps). AC TIMING DIAGRAMS Figure 5. "Worst Case" Test Pattern 6 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 Figure 6. DS90CR285 (Transmitter) LVDS Output Load and Transition Times Figure 7. DS90CR286 (Receiver) CMOS/TTL Output Load and Transition Times Figure 8. DS90CR285 (Transmitter) Input Clock Transition Time (1) Measurements at VDIFF = 0V (2) TCCS measured between earliest and latest LVDS edges. (3) TxCLK Differential LowHigh Edge Figure 9. DS90CR285 (Transmitter) Channel-to-Channel Skew Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 7 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com Figure 10. DS90CR285 (Transmitter) Setup/Hold and High/Low Times Figure 11. DS90CR286 (Receiver) Setup/Hold and High/Low Times Figure 12. DS90CR285 (Transmitter) Clock In to Clock Out Delay Figure 13. DS90CR286 (Receiver) Clock In to Clock Out Delay 8 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 Figure 14. DS90CR285 (Transmitter) Phase Lock Loop Set Time Figure 15. DS90CR286 (Receiver) Phase Lock Loop Set Time Figure 16. Seven Bits of LVDS in Once Clock Cycle Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 9 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com Figure 17. 28 ParalIeI TTL Data Inputs Mapped to LVDS Outputs Figure 18. Transmitter Powerdown DeIay Figure 19. Receiver Powerdown Delay 10 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 Figure 20. Transmitter LVDS Output Pulse Position Measurement Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 11 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com Figure 21. Receiver LVDS Input Strobe Position 12 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 C--Setup and Hold Time (Internal data sampling window) defined by Rspos (receiver input strobe position) min and max Tppos--Transmitter output pulse position (min and max) RSKM Cable Skew (type, length) + Source Clock Jitter (cycle to cycle) + ISI (Inter-symbol interference) Cable Skew--typically 10 ps-40 ps per foot, media dependent (1) Cycle-to-cycle jitter is less than 250 ps (2) ISI is dependent on interconnect length; may be zero Figure 22. Receiver LVDS Input Skew Margin Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 13 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com DS90CR285 DGG (TSSOP) Package Pin Description -- Channel Link Transmitter Pin Name I/O No. Description TxIN I 28 TTL level input. TxOUT+ O 4 Positive LVDS differential data output. TxOUT- O 4 Negative LVDS differential data output. TxCLK IN I 1 TTL IeveI clock input. The rising edge acts as data strobe. Pin name TxCLK IN. TxCLK OUT+ O 1 Positive LVDS differential clock output. TxCLK OUT- O 1 Negative LVDS differential clock output. PWR DWN I 1 TTL level input. Assertion (low input) TRI-STATES the outputs, ensuring low current at power down. VCC I 4 Power supply pins for TTL inputs. GND I 5 Ground pins for TTL inputs. PLL VCC I 1 Power supply pin for PLL. PLL GND I 2 Ground pins for PLL. LVDS VCC I 1 Power supply pin for LVDS outputs. LVDS GND I 3 Ground pins for LVDS outputs. DS90CR286 DGG (TSSOP) Package Pin Description -- Channel Link Receiver Pin Name RxIN+ I/O No. I 4 Positive LVDS differential data inputs. Description RxIN- I 4 Negative LVDS differential data inputs. RxOUT O 28 TTL level data outputs. RxCLK IN+ I 1 Positive LVDS differential clock input. RxCLK IN- I 1 Negative LVDS differential clock input. RxCLK OUT O 1 TTL level clock output. The rising edge acts as data strobe. Pin name RxCLK OUT. PWR DWN I 1 TTL level input.When asserted (low input) the receiver outputs are low. VCC I 4 Power supply pins for TTL outputs. GND I 5 Ground pins for TTL outputs. PLL VCC I 1 Power supply for PLL. PLL GND I 2 Ground pin for PLL. LVDS VCC I 1 Power supply pin for LVDS inputs. LVDS GND I 3 Ground pins for LVDS inputs. 14 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 APPLICATIONS INFORMATION The Channel Link devices are intended to be used in a wide variety of data transmission applications. Depending upon the application the interconnecting media may vary. For example, for lower data rate (clock rate) and shorter cable lengths (< 2m), the media electrical performance is less critical. For higher speed/long distance applications the media's performance becomes more critical. Certain cable constructions provide tighter skew (matched electrical length between the conductors and pairs). Twin-coax for example, has been demonstrated at distances as great as 5 meters and with the maximum data transfer of 1.848 Gbit/s. Additional applications information can be found in the following Interface Application Notes: AN = #### Topic AN-1041 (SNLA218) Introduction to Channel Link AN-1108 (SNLA008) Channel Link PCB and Interconnect Design-In Guidelines AN-806 (SNLA026) Transmission Line Theory AN-905 (SNSNLA035L A008) Transmission Line Calculations and Differential Impedance AN-916 (SNLA219) Cable Information CABLES A cable interface between the transmitter and receiver needs to support the differential LVDS pairs. The 21-bit CHANNEL LINK chipset (DS90CR215/216) requires four pairs of signal wires and the 28-bit CHANNEL LINK chipset (DS90CR285/286) requires five pairs of signal wires. The ideal cable/connector interface would have a constant 100 differential impedance throughout the path. It is also recommended that cable skew remain below 150 ps (@ 66 MHz clock rate) to maintain a sufficient data sampling window at the receiver. In addition to the four or five cable pairs that carry data and clock, it is recommended to provide at least one additional conductor (or pair) which connects ground between the transmitter and receiver. This low impedance ground provides a common mode return path for the two devices. Some of the more commonly used cable types for point-to-point applications include flat ribbon, flex, twisted pair and Twin-Coax. All are available in a variety of configurations and options. Flat ribbon cable, flex and twisted pair generally perform well in short point-to-point applications while Twin-Coax is good for short and long applications. When using ribbon cable, it is recommended to place a ground line between each differential pair to act as a barrier to noise coupling between adjacent pairs. For Twin-Coax cable applications, it is recommended to utilize a shield on each cable pair. All extended point-to-point applications should also employ an overall shield surrounding all cable pairs regardless of the cable type. This overall shield results in improved transmission parameters such as faster attainable speeds, longer distances between transmitter and receiver and reduced problems associated with EMS or EMI. The high-speed transport of LVDS signals has been demonstrated on several types of cables with excellent results. However, the best overall performance has been seen when using Twin-Coax cable. Twin-Coax has very low cable skew and EMI due to its construction and double shielding. All of the design considerations discussed here and listed in the supplemental application notes provide the subsystem communications designer with many useful guidelines. It is recommended that the designer assess the tradeoffs of each application thoroughly to arrive at a reliable and economical cable solution. BOARD LAYOUT To obtain the maximum benefit from the noise and EMI reductions of LVDS, attention should be paid to the layout of differential lines. Lines of a differential pair should always be adjacent to eliminate noise interference from other signals and take full advantage of the noise canceling of the differential signals. The board designer should also try to maintain equal length on signal traces for a given differential pair. As with any high speed design, the impedance discontinuities should be limited (reduce the numbers of vias and no 90 degree angles on traces). Any discontinuities which do occur on one signal line should be mirrored in the other line of the differential pair. Care should be taken to ensure that the differential trace impedance match the differential Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 15 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com impedance of the selected physical media (this impedance should also match the value of the termination resistor that is connected across the differential pair at the receiver's input). Finally, the location of the CHANNEL LINK TxOUT/RxIN pins should be as close as possible to the board edge so as to eliminate excessive pcb runs. All of these considerations will limit reflections and crosstalk which adversely effect high frequency performance and EMI. UNUSED INPUTS All unused inputs at the TxIN inputs of the transmitter must be tied to ground. All unused outputs at the RxOUT outputs of the receiver must then be left floating. INPUTS The TxIN and control inputs are compatible with LVCMOS and LVTTL levels. These pins are not 5V tolerant. TERMINATION Use of current mode drivers requires a terminating resistor across the receiver inputs. The CHANNEL LINK chipset will normally require a single 100 resistor between the true and complement lines on each differential pair of the receiver input. The actual value of the termination resistor should be selected to match the differential mode characteristic impedance (90 to 120 typical) of the cable. Figure 23 shows an example. No additional pull-up or pull-down resistors are necessary as with some other differential technologies such as PECL. Surface mount resistors are recommended to avoid the additional inductance that accompanies leaded resistors. These resistors should be placed as close as possible to the receiver input pins to reduce stubs and effectively terminate the differential lines. DECOUPLING CAPACITORS Bypassing capacitors are needed to reduce the impact of switching noise which could limit performance. For a conservative approach three parallel-connected decoupling capacitors (Multi-Layered Ceramic type in surface mount form factor) between each VCC and the ground plane(s) are recommended. The three capacitor values are 0.1 F, 0.01F and 0.001 F. An example is shown in Figure 24. The designer should employ wide traces for power and ground and ensure each capacitor has its own via to the ground plane. If board space is limiting the number of bypass capacitors, the PLL VCC should receive the most filtering/bypassing. Next would be the LVDS VCC pins and finally the logic VCC pins. Figure 23. LVDS Serialized Link Termination 16 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 Figure 24. CHANNEL LINK Decoupling Configuration CLOCK JITTER The CHANNEL LINK devices employ a PLL to generate and recover the clock transmitted across the LVDS interface. The width of each bit in the serialized LVDS data stream is one-seventh the clock period. For example, a 66 MHz clock has a period of 15 ns which results in a data bit width of 2.16 ns. Differential skew (t within one differential pair), interconnect skew (t of one differential pair to another) and clock jitter will all reduce the available window for sampling the LVDS serial data streams. Care must be taken to ensure that the clock input to the transmitter be a clean low noise signal. Individual bypassing of each VCC to ground will minimize the noise passed on to the PLL, thus creating a low jitter LVDS clock. These measures provide more margin for channelto-channel skew and interconnect skew as a part of the overall jitter/skew budget. COMMON MODE vs. DIFFERENTIAL MODE NOISE MARGIN The typical signal swing for LVDS is 300 mV centered at +1.2V. The CHANNEL LINK receiver supports a 100 mV threshold therefore providing approximately 200 mV of differential noise margin. Common mode protection is of more importance to the system's operation due to the differential data transmission. LVDS supports an input voltage range of Ground to +2.4V. This allows for a 1.0V shifting of the center point due to ground potential differences and common mode noise. POWER SEQUENCING AND POWERDOWN MODE Outputs of the CNANNEL LINK transmitter remain in TRI-STATE until the power supply reaches 2V. Clock and data outputs will begin to toggle 10 ms after VCC has reached 3V and the Powerdown pin is above 1.5V. Either device may be placed into a powerdown mode at any time by asserting the Powerdown pin (active low). Total power dissipation for each device will decrease to 5 W (typical). The CHANNEL LINK chipset is designed to protect itself from accidental loss of power to either the transmitter or receiver. If power to the transmit board is lost, the receiver clocks (input and output) stop. The data outputs (RxOUT) retain the states they were in when the clocks stopped. When the receiver board loses power, the receiver inputs are shorted to V CC through an internal diode. Current is limited (5 mA per input) by the fixed current mode drivers, thus avoiding the potential for latchup when powering the device. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 17 DS90CR285, DS90CR286 SNLS130C - MARCH 1999 - REVISED MARCH 2013 www.ti.com Figure 25. Single-Ended and Differential Waveforms 18 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 DS90CR285, DS90CR286 www.ti.com SNLS130C - MARCH 1999 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision B (March 2013) to Revision C * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 18 Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS90CR285 DS90CR286 Submit Documentation Feedback 19 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) DS90CR285MTD NRND TSSOP DGG 56 34 TBD Call TI Call TI -40 to 85 DS90CR285MTD >B DS90CR285MTD/NOPB ACTIVE TSSOP DGG 56 34 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 85 DS90CR285MTD >B DS90CR285MTDX NRND TSSOP DGG 56 1000 TBD Call TI Call TI -40 to 85 DS90CR285MTD >B DS90CR285MTDX/NOPB ACTIVE TSSOP DGG 56 1000 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR -40 to 85 DS90CR285MTD >B DS90CR286MTD NRND TSSOP DGG 56 34 TBD Call TI Call TI DS90CR286MTD >B DS90CR286MTD/NOPB NRND TSSOP DGG 56 34 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR DS90CR286MTD >B DS90CR286MTDX/NOPB NRND TSSOP DGG 56 1000 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR DS90CR286MTD >B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 26-Mar-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device DS90CR285MTDX Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TSSOP DGG 56 1000 330.0 24.4 8.6 14.5 1.8 12.0 24.0 Q1 DS90CR285MTDX/NOPB TSSOP DGG 56 1000 330.0 24.4 8.6 14.5 1.8 12.0 24.0 Q1 DS90CR286MTDX/NOPB TSSOP DGG 56 1000 330.0 24.4 8.6 14.5 1.8 12.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 26-Mar-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS90CR285MTDX TSSOP DGG 56 1000 367.0 367.0 45.0 DS90CR285MTDX/NOPB TSSOP DGG 56 1000 367.0 367.0 45.0 DS90CR286MTDX/NOPB TSSOP DGG 56 1000 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated