5CSEBA6U23I7N - Altera Corporation

Cyclone V Device Overview

2016.06.10

CV-51001 Subscribe Send Feedback

The Cyclone® V devices are designed to simultaneously accommodate the shrinking power consumption,

cost, and time-to-market requirements; and the increasing bandwidth requirements for high-volume and

cost-sensitive applications.

Enhanced with integrated transceivers and hard memory controllers, the Cyclone V devices are suitable

for applications in the industrial, wireless and wireline, military, and automotive markets.

Related Information

Cyclone V Device Handbook: Known Issues

Lists the planned updates to the Cyclone V Device Handbook chapters.

Key Advantages of Cyclone V Devices

Table 1: Key Advantages of the Cyclone V Device Family

Advantage Supporting Feature

Lower power consumption • Built on TSMC's 28 nm low-power (28LP) process technology and

includes an abundance of hard intellectual property (IP) blocks

• Up to 40% lower power consumption than the previous generation

device

Improved logic integration

and differentiation capabil‐

ities

• 8-input adaptive logic module (ALM)

• Up to 13.59 megabits (Mb) of embedded memory

• Variable-precision digital signal processing (DSP) blocks

Increased bandwidth

capacity • 3.125 gigabits per second (Gbps) and 6.144 Gbps transceivers

• Hard memory controllers

Hard processor system

(HPS) with integrated

ARM® Cortex™-A9

MPCore processor

• Tight integration of a dual-core ARM Cortex-A9 MPCore processor,

hard IP, and an FPGA in a single Cyclone V system-on-a-chip (SoC)

• Supports over 128 Gbps peak bandwidth with integrated data coherency

between the processor and the FPGA fabric

trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as

trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance

of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any

products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information,

product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device

specifications before relying on any published information and before placing orders for products or services.

ISO

9001:2008

Registered

www.altera.com

101 Innovation Drive, San Jose, CA 95134

Advantage Supporting Feature

Lowest system cost • Requires only two core voltages to operate

• Available in low-cost wirebond packaging

• Includes innovative features such as Configuration via Protocol (CvP)

and partial reconfiguration

Summary of Cyclone V Features

Table 2: Summary of Features for Cyclone V Devices

Feature Description

Technology • TSMC's 28-nm low-power (28LP) process technology

• 1.1 V core voltage

Packaging • Wirebond low-halogen packages

• Multiple device densities with compatible package footprints for seamless

migration between different device densities

• RoHS-compliant and leaded(1)options

High-performance

FPGA fabric Enhanced 8-input ALM with four registers

Internal memory

blocks • M10K—10-kilobits (Kb) memory blocks with soft error correction code (ECC)

• Memory logic array block (MLAB)—640-bit distributed LUTRAM where you can

use up to 25% of the ALMs as MLAB memory

Embedded Hard IP

blocks

Variable-precision

DSP • Native support for up to three signal processing precision

levels (three 9 x 9, two 18 x 18, or one 27 x 27 multiplier) in

the same variable-precision DSP block

• 64-bit accumulator and cascade

• Embedded internal coefficient memory

• Preadder/subtractor for improved efficiency

Memory controller DDR3, DDR2, and LPDDR2 with 16 and 32 bit ECC support

Embedded

transceiver I/O PCI Express® (PCIe®) Gen2 and Gen1 (x1, x2, or x4) hard IP

with multifunction support, endpoint, and root port

Clock networks • Up to 550 MHz global clock network

• Global, quadrant, and peripheral clock networks

• Clock networks that are not used can be powered down to reduce dynamic power

(1) Contact Altera for availability.

2Summary of Cyclone V Features CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Feature Description

Phase-locked loops

(PLLs) • Precision clock synthesis, clock delay compensation, and zero delay buffering

(ZDB)

• Integer mode and fractional mode

FPGA General-

purpose I/Os

(GPIOs)

• 875 megabits per second (Mbps) LVDS receiver and 840 Mbps LVDS transmitter

• 400 MHz/800 Mbps external memory interface

• On-chip termination (OCT)

• 3.3 V support with up to 16 mA drive strength

Low-power high-

speed serial interface • 614 Mbps to 6.144 Gbps integrated transceiver speed

• Transmit pre-emphasis and receiver equalization

• Dynamic partial reconfiguration of individual channels

HPS

( Cyclone V SE, SX,

and ST devices only)

• Single or dual-core ARM Cortex-A9 MPCore processor-up to 925 MHz maximum

frequency with support for symmetric and asymmetric multiprocessing

• Interface peripherals—10/100/1000 Ethernet media access control (EMAC),

USB 2.0 On-The-GO (OTG) controller, quad serial peripheral interface (QSPI)

flash controller, NAND flash controller, Secure Digital/MultiMediaCard (SD/

MMC) controller, UART, controller area network (CAN), serial peripheral

interface (SPI), I2C interface, and up to 85 HPS GPIO interfaces

• System peripherals—general-purpose timers, watchdog timers, direct memory

access (DMA) controller, FPGA configuration manager, and clock and reset

managers

• On-chip RAM and boot ROM

• HPS–FPGA bridges—include the FPGA-to-HPS, HPS-to-FPGA, and lightweight

HPS-to-FPGA bridges that allow the FPGA fabric to issue transactions to slaves in

the HPS, and vice versa

• FPGA-to-HPS SDRAM controller subsystem—provides a configurable interface to

the multiport front end (MPFE) of the HPS SDRAM controller

• ARM CoreSight™ JTAG debug access port, trace port, and on-chip trace storage

Configuration • Tamper protection—comprehensive design protection to protect your valuable IP

investments

• Enhanced advanced encryption standard (AES) design security features

• CvP

• Dynamic reconfiguration of the FPGA

• Active serial (AS) x1 and x4, passive serial (PS), JTAG, and fast passive parallel

(FPP) x8 and x16 configuration options

• Internal scrubbing (2)

• Partial reconfiguration (3)

(2) The SEU internal scrubbing feature is available for Cyclone V E, GX, SE, and SX devices with the "SC"

suffix in the part number. For device availability and ordering, contact your local Altera sales representa‐

tives.

CV-51001

2016.06.10 Summary of Cyclone V Features 3

Cyclone V Device Overview Altera Corporation

Send Feedback

Cyclone V Device Variants and Packages

Table 3: Device Variants for the Cyclone V Device Family

Variant Description

Cyclone V E Optimized for the lowest system cost and power requirement for a wide spectrum of

general logic and DSP applications

Cyclone V GX Optimized for the lowest cost and power requirement for 614 Mbps to 3.125 Gbps

transceiver applications

Cyclone V GT The FPGA industry’s lowest cost and lowest power requirement for 6.144 Gbps

transceiver applications

Cyclone V SE SoC with integrated ARM-based HPS

Cyclone V SX SoC with integrated ARM-based HPS and 3.125 Gbps transceivers

Cyclone V ST SoC with integrated ARM-based HPS and 6.144 Gbps transceivers

Cyclone V E

This section provides the available options, maximum resource counts, and package plan for the

Cyclone V E devices.

The information in this section is correct at the time of publication. For the latest information and to get

more details, refer to the Altera Product Selector.

Related Information

Altera Product Selector

Provides the latest information about Altera products.

(3) The partial reconfiguration feature is available for Cyclone V E, GX, SE, and SX devices with the "SC"

suffix in the part number. For device availability and ordering, contact your local Altera sales representa‐

tives.

4Cyclone V Device Variants and Packages CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Available Options

Figure 1: Sample Ordering Code and Available Options for Cyclone V E Devices

The SEU internal scrubbing feature is available for Cyclone V E, GX, SE, and SX devices with the "SC"

suffix in the part number. For device availability and ordering, contact your local Altera sales

representatives.

Family Signature

Embedded Hard IPs

Package Type

Package Code

Operating Temperature

FPGA Fabric Speed Grade

Optional Suffix

Indicates specific device

options or shipment method

E : Enhanced logic/memory

B : No hard PCIe or hard

memory controller

F : No hard PCIe and maximum

2 hard memory controllers

5C : Cyclone V

F : FineLine BGA (FBGA)

U : Ultra FineLine BGA (UBGA)

M : Micro FineLine BGA (MBGA)

FBGA Package Type

17 : 256 pins

23 : 484 pins

27 : 672 pins

31 : 896 pins

UBGA Package Type

15 : 324 pins

19 : 484 pins

MBGA Package Type

13 : 383 pins

15 : 484 pins

C : Commercial (TJ = 0° C to 85° C)

I : Industrial (TJ = -40° C to 100° C)

A : Automotive (TJ = -40° C to 125° C)

6 (fastest)

N : Lead-free packaging

Contact Altera for availability

of leaded options

ES : Engineering sample

5C E F A9 F 31 C7N

Member Code

Family Variant

A2 : 25K logic elements

A4 : 49K logic elements

A5 : 77K logic elements

A7 : 150K logic elements

A9 : 301K logic elements

SC : Internal scrubbing support

Maximum Resources

Table 4: Maximum Resource Counts for Cyclone V E Devices

Resource Member Code

A2 A4 A5 A7 A9

Logic Elements (LE) (K) 25 49 77 150 301

ALM 9,434 18,480 29,080 56,480 113,560

Memory

(Kb)

M10K 1,760 3,080 4,460 6,860 12,200

MLAB 196 303 424 836 1,717

Variable-precision DSP

Block 25 66 150 156 342

18 x 18 Multiplier 50 132 300 312 684

PLL 4 4 6 7 8

CV-51001

2016.06.10 Available Options 5

Cyclone V Device Overview Altera Corporation

Send Feedback

Resource Member Code

A2 A4 A5 A7 A9

GPIO 224 224 240 480 480

LVDS Transmitter 56 56 60 120 120

Receiver 56 56 60 120 120

Hard Memory Controller 1 1 2 2 2

Related Information

True LVDS Buffers in Devices, I/O Features in Cyclone V Devices

Provides the number of LVDS channels in each device package.

Package Plan

Table 5: Package Plan for Cyclone V E Devices

Member

Code

M383

(13 mm)

M484

(15 mm)

U324

(15 mm)

F256

(17 mm)

U484

(19 mm)

F484

(23 mm)

F672

(27 mm)

F896

(31 mm)

GPIO GPIO GPIO GPIO GPIO GPIO GPIO GPIO

A2 223 — 176 128 224 224 — —

A4 223 — 176 128 224 224 — —

A5 175 — — — 224 240 — —

A7 — 240 — — 240 240 336 480

A9 — — — — 240 224 336 480

Cyclone V GX

This section provides the available options, maximum resource counts, and package plan for the

Cyclone V GX devices.

The information in this section is correct at the time of publication. For the latest information and to get

more details, refer to the Altera Product Selector.

Related Information

Altera Product Selector

Provides the latest information about Altera products.

6Package Plan CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Available Options

Figure 2: Sample Ordering Code and Available Options for Cyclone V GX Devices

The SEU internal scrubbing feature is available for Cyclone V E, GX, SE, and SX devices with the "SC"

suffix in the part number. For device availability and ordering, contact your local Altera sales

representatives.

Family Signature

Embedded Hard IPs

Transceiver Count

Transceiver

Speed Grade

Package Type

Package Code

Operating Temperature

FPGA Fabric

Speed Grade

Optional Suffix

Indicates specific device

options or shipment method

GX : 3-Gbps transceivers

B : No hard PCIe or hard

memory controller

F : Maximum 2 hard PCIe and

2 hard memory controllers

5C : Cyclone V

C3 :

36K logic elements

C4 : 50K logic elements

C5 : 77K logic elements

C7 : 150K logic elements

C9 : 301K logic elements

B : 3

F : 4

A : 5

C : 6

D : 9

E : 12

6 : 3.125 Gbps

7 : 2.5 Gbps

F : FineLine BGA (FBGA)

U : Ultra FineLine BGA (UBGA)

M : Micro FineLine BGA (MBGA)

FBGA Package Type

23 : 484 pins

27 : 672 pins

31 : 896 pins

35 : 1,152 pins

UBGA Package Type

15 : 324 pins

19 : 484 pins

MBGA Package Type

11 : 301 pins

13 : 383 pins

15 : 484 pins

C : Commercial (TJ = 0° C to 85° C)

I : Industrial (TJ = -40° C to 100° C)

A : Automotive (TJ = -40° C to 125° C)

6 (fastest)

N : Lead-free packaging

Contact Altera for availability

of leaded options

Engineering sample

5C GX FC9 E 6F 35 C7N

Member Code

Family Variant

SC : Internal scrubbing support

Maximum Resources

Table 6: Maximum Resource Counts for Cyclone V GX Devices

Resource Member Code

C3 C4 C5 C7 C9

Logic Elements (LE) (K) 36 50 77 150 301

ALM 13,460 18,860 29,080 56,480 113,560

Memory

(Kb)

M10K 1,350 2,500 4,460 6,860 12,200

MLAB 182 424 424 836 1,717

Variable-precision DSP

Block 57 70 150 156 342

18 x 18 Multiplier 114 140 300 312 684

CV-51001

2016.06.10 Available Options 7

Cyclone V Device Overview Altera Corporation

Send Feedback

Resource Member Code

C3 C4 C5 C7 C9

PLL 4 6 6 7 8

3 Gbps Transceiver 3 6 6 9 12

GPIO(4) 208 336 336 480 560

LVDS Transmitter 52 84 84 120 140

Receiver 52 84 84 120 140

PCIe Hard IP Block 1 2 2 2 2

Hard Memory

Controller 1 2 2 2 2

Related Information

True LVDS Buffers in Devices, I/O Features in Cyclone V Devices

Provides the number of LVDS channels in each device package.

Package Plan

Table 7: Package Plan for Cyclone V GX Devices

Member

Code

M301

(11 mm)

M383

(13 mm)

M484

(15 mm)

U324

(15 mm)

U484

(19 mm)

GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR

C3 — — — — — — 144 3 208 3

C4 129 4 175 6 — — — — 224 6

C5 129 4 175 6 — — — — 224 6

C7 — — — — 240 3 — — 240 6

C9 — — — — — — — — 240 5

Member

Code

F484

(23 mm)

F672

(27 mm)

F896

(31 mm)

F1152

(35 mm)

GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR

C3 208 3 — — — — — —

C4 240 6 336 6 — — — —

C5 240 6 336 6 — — — —

C7 240 6 336 9 480 9 — —

C9 224 6 336 9 480 12 560 12

(4) The number of GPIOs does not include transceiver I/Os. In the Quartus® Prime software, the number of

user I/Os includes transceiver I/Os.

8Package Plan CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Cyclone V GT

This section provides the available options, maximum resource counts, and package plan for the

Cyclone V GT devices.

The information in this section is correct at the time of publication. For the latest information and to get

more details, refer to the Altera Product Selector.

Related Information

Altera Product Selector

Provides the latest information about Altera products.

Available Options

Figure 3: Sample Ordering Code and Available Options for Cyclone V GT Devices

Family Signature

Embedded Hard IPs

Transceiver Count

Transceiver

Speed Grade

Package Type

Package Code

Operating Temperature

FPGA Fabric

Speed Grade

GT : 6-Gbps transceivers

F : Maximum 2 hard PCIe and

2 hard memory controllers

5C : Cyclone V

D5 : 77K logic elements

D7 : 150K logic elements

D9 : 301K logic elements

B : 3

F : 4

A : 5

C : 6

D : 9

E : 12

5 : 6.144 Gbps

F : FineLine BGA (FBGA)

U : Ultra FineLine BGA (UBGA)

M : Micro FineLine BGA (MBGA)

FBGA Package Type

23 : 484 pins

27 : 672 pins

31 : 896 pins

35 : 1,152 pins

UBGA Package Type

19 : 484 pins

MBGA Package Type

11 : 301 pins

13 : 383 pins

15 : 484 pins

C : Commercial (TJ = 0° C to 85° C)

I : Industrial (TJ = -40° C to 100° C)

A : Automotive (TJ = -40° C to 125° C)

5C GT F D9 E 5 F 35 C 7N

Member Code

Family Variant Optional Suffix

Indicates specific device

options or shipment method

N : Lead-free packaging

Contact Altera for availability

of leaded options

ES : Engineering sample

Maximum Resources

Table 8: Maximum Resource Counts for Cyclone V GT Devices

Resource Member Code

D5 D7 D9

Logic Elements (LE) (K) 77 150 301

ALM 29,080 56,480 113,560

CV-51001

2016.06.10 Cyclone V GT 9

Cyclone V Device Overview Altera Corporation

Send Feedback

Resource Member Code

D5 D7 D9

Memory (Kb) M10K 4,460 6,860 12,200

MLAB 424 836 1,717

Variable-precision DSP Block 150 156 342

18 x 18 Multiplier 300 312 684

PLL 6 7 8

6 Gbps Transceiver 6 9 12

GPIO(5) 336 480 560

LVDS Transmitter 84 120 140

Receiver 84 120 140

PCIe Hard IP Block 2 2 2

Hard Memory Controller 2 2 2

Related Information

True LVDS Buffers in Devices, I/O Features in Cyclone V Devices

Provides the number of LVDS channels in each device package.

Package Plan

Table 9: Package Plan for Cyclone V GT Devices

Transceiver counts shown are for transceiver ≤5 Gbps . 6 Gbps transceiver channel count support depends on the

package and channel usage. For more information about the 6 Gbps transceiver channel count, refer to the

Cyclone V Device Handbook Volume 2: Transceivers.

Member

Code

M301

(11 mm)

M383

(13 mm)

M484

(15 mm)

U484

(19 mm)

GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR

D5 129 4 175 6 — — 224 6

D7 — — — — 240 3 240 6

D9 — — — — — — 240 5

Member

Code

F484

(23 mm)

F672

(27 mm)

F896

(31 mm)

F1152

(35 mm)

GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR

D5 240 6 336 6 — — — —

D7 240 6 336 9 (6) 480 9 (6) — —

(5) The number of GPIOs does not include transceiver I/Os. In the Quartus Prime software, the number of user

I/Os includes transceiver I/Os.

10 Package Plan CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Member

Code

F484

(23 mm)

F672

(27 mm)

F896

(31 mm)

F1152

(35 mm)

GPIO XCVR GPIO XCVR GPIO XCVR GPIO XCVR

D9 224 6 336 9 (6) 480 12 (7) 560 12 (7)

Related Information

6.144-Gbps Support Capability in Cyclone V GT Devices, Cyclone V Device Handbook Volume 2:

Transceivers

Provides more information about 6 Gbps transceiver channel count.

Cyclone V SE

This section provides the available options, maximum resource counts, and package plan for the

Cyclone V SE devices.

The information in this section is correct at the time of publication. For the latest information and to get

more details, refer to the Altera Product Selector.

Related Information

Altera Product Selector

Provides the latest information about Altera products.

(6) If you require CPRI (at 6.144 Gbps) and PCIe Gen2 transmit jitter compliance, Altera recommends that you

use only up to three full-duplex transceiver channels for CPRI, and up to six full-duplex channels for PCIe

Gen2. The CMU channels are not considered full-duplex channels.

(7) If you require CPRI (at 6.144 Gbps) and PCIe Gen2 transmit jitter compliance, Altera recommends that you

use only up to three full-duplex transceiver channels for CPRI, and up to eight full-duplex channels for PCIe

Gen2. The CMU channels are not considered full-duplex channels.

CV-51001

2016.06.10 Cyclone V SE 11

Cyclone V Device Overview Altera Corporation

Send Feedback

Available Options

Figure 4: Sample Ordering Code and Available Options for Cyclone V SE Devices

The SEU internal scrubbing feature is available for Cyclone V E, GX, SE, and SX devices with the "SC"

suffix in the part number. For device availability and ordering, contact your local Altera sales

representatives.

Family Signature

Embedded Hard IPs

Package Type

Package Code

Operating Temperature

FPGA Fabric

Speed Grade

Optional Suffix

Indicates specific device

options or shipment method

SE : SoC with enhanced logic/memory

5C : Cyclone V

F : FineLine BGA (FBGA)

U : Ultra FineLine BGA (UBGA)

FBGA Package Type

31 : 896 pins

UBGA Package Type

19 : 484 pins

23 : 672 pins

C : Commercial (TJ = 0° C to 85° C)

I : Industrial (TJ = -40° C to 100° C)

A : Automotive (TJ = -40° C to 125° C)

6 (fastest)

Processor Cores

Omit for dual-core

S : Single-core

N : Lead-free packaging

Contact Altera for availability

of leaded options

ES : Engineering sample

5C SE M A6 F 31 C6 S N

Member Code

Family Variant

A2 : 25K logic elements

A4 : 40K logic elements

A5 : 85K logic elements

A6 : 110K logic elements

B : No hard PCIe or hard

memory controller

M : No hard PCIe and

1 hard memory controller

SC : Internal scrubbing support

12 Available Options CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Maximum Resources

Table 10: Maximum Resource Counts for Cyclone V SE Devices

Resource Member Code

A2 A4 A5 A6

Logic Elements (LE) (K) 25 40 85 110

ALM 9,434 15,094 32,075 41,509

Memory

(Kb)

M10K 1,400 2,700 3,970 5,570

MLAB 138 231 480 621

Variable-precision DSP

Block 36 84 87 112

18 x 18 Multiplier 72 168 174 224

FPGA PLL 5 5 6 6

HPS PLL 3 3 3 3

FPGA GPIO 145 145 288 288

HPS I/O 181 181 181 181

LVDS Transmitter 32 32 72 72

Receiver 37 37 72 72

FPGA Hard Memory

Controller 1 1 1 1

HPS Hard Memory

Controller 1 1 1 1

ARM Cortex-A9 MPCore

Processor Single- or

dual-core Single- or

dual-core Single- or dual-

core Single- or dual-core

Related Information

True LVDS Buffers in Devices, I/O Features in Cyclone V Devices

Provides the number of LVDS channels in each device package.

Package Plan

Table 11: Package Plan for Cyclone V SE Devices

The HPS I/O counts are the number of I/Os in the HPS and does not correlate with the number of HPS-specific

I/O pins in the FPGA. Each HPS-specific pin in the FPGA may be mapped to several HPS I/Os.

Member

Code

U484

(19 mm)

U672

(23 mm)

F896

(31 mm)

FPGA GPIO HPS I/O FPGA GPIO HPS I/O FPGA GPIO HPS I/O

A2 66 151 145 181 — —

CV-51001

2016.06.10 Maximum Resources 13

Cyclone V Device Overview Altera Corporation

Send Feedback

Member

Code

U484

(19 mm)

U672

(23 mm)

F896

(31 mm)

FPGA GPIO HPS I/O FPGA GPIO HPS I/O FPGA GPIO HPS I/O

A4 66 151 145 181 — —

A5 66 151 145 181 288 181

A6 66 151 145 181 288 181

Cyclone V SX

This section provides the available options, maximum resource counts, and package plan for the

Cyclone V SX devices.

The information in this section is correct at the time of publication. For the latest information and to get

more details, refer to the Altera Product Selector.

Related Information

Altera Product Selector

Provides the latest information about Altera products.

Available Options

Figure 5: Sample Ordering Code and Available Options for Cyclone V SX Devices

The SEU internal scrubbing feature is available for Cyclone V E, GX, SE, and SX devices with the "SC"

suffix in the part number. For device availability and ordering, contact your local Altera sales

representatives.

Family Signature

Embedded Hard IPs Transceiver Count

Transceiver

Speed Grade

Package Type

Package Code

Operating Temperature

FPGA Fabric

Speed Grade

Optional Suffix

Indicates specific device

options or shipment method

SX : SoC with 3-Gbps transceivers

F : Maximum 2 hard PCIe

controllers and 1 hard

memory controller

5C : Cyclone V

C2 : 25K logic elements

C4 : 40K logic elements

C5 : 85K logic elements

C6 : 110K logic elements

C : 6

D : 9

6 : 3.125 Gbps

F : FineLine BGA (FBGA)

U : Ultra FineLine BGA (UBGA)

FBGA Package Type

31 : 896 pins

UBGA Package Type

23 : 672 pins

C : Commercial (TJ = 0° C to 85° C)

I : Industrial (TJ = -40° C to 100° C)

A : Automotive (TJ = -40° C to 125° C)

6 (fastest)

N : Lead-free packaging

Contact Altera for availability

of leaded options

ES : Engineering sample

5C SX FC6 D 6F 31 C6N

Member Code

Family Variant

SC : Internal scrubbing support

14 Cyclone V SX CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Maximum Resources

Table 12: Maximum Resource Counts for Cyclone V SX Devices

Resource Member Code

C2 C4 C5 C6

Logic Elements (LE) (K) 25 40 85 110

ALM 9,434 15,094 32,075 41,509

Memory

(Kb)

M10K 1,400 2,700 3,970 5,570

MLAB 138 231 480 621

Variable-precision DSP Block 36 84 87 112

18 x 18 Multiplier 72 168 174 224

FPGA PLL 5 5 6 6

HPS PLL 3 3 3 3

3 Gbps Transceiver 6 6 9 9

FPGA GPIO (8) 145 145 288 288

HPS I/O 181 181 181 181

LVDS Transmitter 32 32 72 72

Receiver 37 37 72 72

PCIe Hard IP Block 2 2 2 (9) 2 (9)

FPGA Hard Memory

Controller 1 1 1 1

HPS Hard Memory

Controller 1 1 1 1

ARM Cortex-A9 MPCore

Processor Dual-core Dual-core Dual-core Dual-core

Related Information

True LVDS Buffers in Devices, I/O Features in Cyclone V Devices

Provides the number of LVDS channels in each device package.

(8) The number of GPIOs does not include transceiver I/Os. In the Quartus Prime software, the number of user

I/Os includes transceiver I/Os.

(9) 1 PCIe Hard IP Block in U672 package.

CV-51001

2016.06.10 Maximum Resources 15

Cyclone V Device Overview Altera Corporation

Send Feedback

Package Plan

Table 13: Package Plan for Cyclone V SX Devices

The HPS I/O counts are the number of I/Os in the HPS and does not correlate with the number of HPS-specific

I/O pins in the FPGA. Each HPS-specific pin in the FPGA may be mapped to several HPS I/Os.

Member

Code

U672

(23 mm)

F896

(31 mm)

FPGA GPIO HPS I/O XCVR FPGA GPIO HPS I/O XCVR

C2 145 181 6 — — —

C4 145 181 6 — — —

C5 145 181 6 288 181 9

C6 145 181 6 288 181 9

Cyclone V ST

This section provides the available options, maximum resource counts, and package plan for the

Cyclone V ST devices.

The information in this section is correct at the time of publication. For the latest information and to get

more details, refer to the Altera Product Selector.

Related Information

Altera Product Selector

Provides the latest information about Altera products.

Available Options

Figure 6: Sample Ordering Code and Available Options for Cyclone V ST Devices

Family Signature

Embedded Hard IPs

Transceiver Count

Transceiver

Speed Grade

Package Type

Package Code

Operating Temperature

FPGA Fabric

Speed Grade

Optional Suffix

Indicates specific device

options or shipment method

ST : SoC with 6.144-Gbps transceivers

F : 2 hard PCIe controllers

and 1 hard memory controller

5C : Cyclone V

D5 : 85K logic elements

D6 : 110K logic elements

D : 9

5 : 6.144 Gbps

F : FineLine BGA (FBGA)

31 : 896 pins

I : Industrial (TJ= -40° C to 100° C)

N : Lead-free packaging

Contact Altera for availability

of leaded options

ES : Engineering sample

5C ST FD6 D 5F 31 C6N

Member Code

Family Variant

16 Package Plan CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Maximum Resources

Table 14: Maximum Resource Counts for Cyclone V ST Devices

Resource Member Code

D5 D6

Logic Elements (LE) (K) 85 110

ALM 32,075 41,509

Memory (Kb) M10K 3,970 5,570

MLAB 480 621

Variable-precision DSP Block 87 112

18 x 18 Multiplier 174 224

FPGA PLL 6 6

HPS PLL 3 3

6.144 Gbps Transceiver 9 9

FPGA GPIO(10) 288 288

HPS I/O 181 181

LVDS Transmitter 72 72

Receiver 72 72

PCIe Hard IP Block 2 2

FPGA Hard Memory Controller 1 1

HPS Hard Memory Controller 1 1

ARM Cortex-A9 MPCore Processor Dual-core Dual-core

Related Information

True LVDS Buffers in Devices, I/O Features in Cyclone V Devices

Provides the number of LVDS channels in each device package.

(10) The number of GPIOs does not include transceiver I/Os. In the Quartus Prime software, the number of user

I/Os includes transceiver I/Os.

CV-51001

2016.06.10 Maximum Resources 17

Cyclone V Device Overview Altera Corporation

Send Feedback

Package Plan

Table 15: Package Plan for Cyclone V ST Devices

• The HPS I/O counts are the number of I/Os in the HPS and does not correlate with the number of HPS-

specific I/O pins in the FPGA. Each HPS-specific pin in the FPGA may be mapped to several HPS I/Os.

• Transceiver counts shown are for transceiver ≤5 Gbps . 6 Gbps transceiver channel count support depends on

the package and channel usage. For more information about the 6 Gbps transceiver channel count, refer to the

Cyclone V Device Handbook Volume 2: Transceivers.

Member Code

F896

(31 mm)

FPGA GPIO HPS I/O XCVR

D5 288 181 9 (11)

D6 288 181 9 (11)

Related Information

6.144-Gbps Support Capability in Cyclone V GT Devices, Cyclone V Device Handbook Volume 2:

Transceivers

Provides more information about 6 Gbps transceiver channel count.

(11) If you require CPRI (at 4.9152 Gbps) and PCIe Gen2 transmit jitter compliance, Altera recommends that you

use only up to seven full-duplex transceiver channels for CPRI, and up to six full-duplex channels for PCIe

Gen2. The CMU channels are not considered full-duplex channels.

18 Package Plan CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

I/O Vertical Migration for Cyclone V Devices

Figure 7: Vertical Migration Capability Across Cyclone V Device Packages and Densities

The arrows indicate the vertical migration paths. The devices included in each vertical migration path are

shaded. You can also migrate your design across device densities in the same package option if the devices

have the same dedicated pins, configuration pins, and power pins.

Variant Member

Code

Package

M301 M383 M484 F256 U324 U484 F484 U672 F672 F896 F1152

Cyclone V E

Cyclone V GX

Cyclone V GT

Cyclone V SE

Cyclone V SX

Cyclone V ST D5

You can achieve the vertical migration shaded in red if you use only up to 175 GPIOs for the M383

package, and 138 GPIOs for the U672 package. These migration paths are not shown in the Quartus

Prime software Pin Migration View.

Note: To verify the pin migration compatibility, use the Pin Migration View window in the Quartus

Prime software Pin Planner.

CV-51001

2016.06.10 I/O Vertical Migration for Cyclone V Devices 19

Cyclone V Device Overview Altera Corporation

Send Feedback

Adaptive Logic Module

Cyclone V devices use a 28 nm ALM as the basic building block of the logic fabric.

The ALM, as shown in following figure, uses an 8-input fracturable look-up table (LUT) with four

dedicated registers to help improve timing closure in register-rich designs and achieve an even higher

design packing capability than previous generations.

Figure 8: ALM for Cyclone V Devices

FPGA Device

Adaptive

LUT

Full

Adder

Reg

Full

Adder

Reg

You can configure up to 25% of the ALMs in the Cyclone V devices as distributed memory using MLABs.

Related Information

Embedded Memory Capacity in Cyclone V Devices on page 23

Lists the embedded memory capacity for each device.

Variable-Precision DSP Block

Cyclone V devices feature a variable-precision DSP block that supports these features:

• Configurable to support signal processing precisions ranging from 9 x 9, 18 x 18 and 27 x 27 bits

natively

• A 64-bit accumulator

• A hard preadder that is available in both 18- and 27-bit modes

• Cascaded output adders for efficient systolic finite impulse response (FIR) filters

• Internal coefficient register banks, 8 deep, for each multiplier in 18- or 27-bit mode

• Fully independent multiplier operation

20 Adaptive Logic Module CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

• A second accumulator feedback register to accommodate complex multiply-accumulate functions

• Fully independent Efficient support for single-precision floating point arithmetic

• The inferability of all modes by the Quartus Prime design software

Table 16: Variable-Precision DSP Block Configurations for Cyclone V Devices

Usage Example Multiplier Size (Bit) DSP Block Resource

Low precision fixed point

for video applications Three 9 x 9 1

Medium precision fixed

point in FIR filters Two 18 x 18 1

FIR filters and general DSP

usage Two 18 x 18 with accumulate 1

High precision fixed- or

floating-point implementa‐

tions

One 27 x 27 with accumulate 1

You can configure each DSP block during compilation as independent three 9 x 9, two 18 x 18, or one

27 x 27 multipliers. With a dedicated 64 bit cascade bus, you can cascade multiple variable-precision DSP

blocks to implement even higher precision DSP functions efficiently.

Table 17: Number of Multipliers in Cyclone V Devices

The table lists the variable-precision DSP resources by bit precision for each Cyclone V device.

Variant Member

Code

Variable-

precision

DSP Block

Independent Input and Output

Multiplications Operator 18 x 18

Multiplier

Adder

Mode

18 x 18

Multiplier Adder

Summed with

36 bit Input

9 x 9

Multiplier

18 x 18

Multiplier

27 x 27

Multiplier

Cyclone V E

A2 25 75 50 25 25 25

A4 66 198 132 66 66 66

A5 150 450 300 150 150 150

A7 156 468 312 156 156 156

A9 342 1,026 684 342 342 342

Cyclone V

C3 57 171 114 57 57 57

C4 70 210 140 70 70 70

C5 150 450 300 150 150 150

C7 156 468 312 156 156 156

C9 342 1,026 684 342 342 342

CV-51001

2016.06.10 Variable-Precision DSP Block 21

Cyclone V Device Overview Altera Corporation

Send Feedback

Variant Member

Code

Variable-

precision

DSP Block

Independent Input and Output

Multiplications Operator 18 x 18

Multiplier

Adder

Mode

18 x 18

Multiplier Adder

Summed with

36 bit Input

9 x 9

Multiplier

18 x 18

Multiplier

27 x 27

Multiplier

Cyclone V

D5 150 450 300 150 150 150

D7 156 468 312 156 156 156

D9 342 1,026 684 342 342 342

Cyclone V

A2 36 108 72 36 36 36

A4 84 252 168 84 84 84

A5 87 261 174 87 87 87

A6 112 336 224 112 112 112

Cyclone V

C2 36 108 72 36 36 36

C4 84 252 168 84 84 84

C5 87 261 174 87 87 87

C6 112 336 224 112 112 112

Cyclone V

D5 87 261 174 87 87 87

D6 112 336 224 112 112 112

Embedded Memory Blocks

The embedded memory blocks in the devices are flexible and designed to provide an optimal amount of

small- and large-sized memory arrays to fit your design requirements.

Types of Embedded Memory

The Cyclone V devices contain two types of memory blocks:

• 10 Kb M10K blocks—blocks of dedicated memory resources. The M10K blocks are ideal for larger

memory arrays while still providing a large number of independent ports.

• 640 bit memory logic array blocks (MLABs)—enhanced memory blocks that are configured from dual-

purpose logic array blocks (LABs). The MLABs are ideal for wide and shallow memory arrays. The

MLABs are optimized for implementation of shift registers for digital signal processing (DSP) applica‐

tions, wide shallow FIFO buffers, and filter delay lines. Each MLAB is made up of ten adaptive logic

modules (ALMs). In the Cyclone V devices, you can configure these ALMs as ten 32 x 2 blocks, giving

you one 32 x 20 simple dual-port SRAM block per MLAB.

22 Embedded Memory Blocks CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Embedded Memory Capacity in Cyclone V Devices

Table 18: Embedded Memory Capacity and Distribution in Cyclone V Devices

Variant Member

Code

M10K MLAB

Total RAM Bit (Kb)Block RAM Bit (Kb) Block RAM Bit (Kb)

Cyclone V E

A2 176 1,760 314 196 1,956

A4 308 3,080 485 303 3,383

A5 446 4,460 679 424 4,884

A7 686 6,860 1338 836 7,696

A9 1,220 12,200 2748 1,717 13,917

Cyclone V GX

C3 135 1,350 291 182 1,532

C4 250 2,500 678 424 2,924

C5 446 4,460 678 424 4,884

C7 686 6,860 1338 836 7,696

C9 1,220 12,200 2748 1,717 13,917

Cyclone V GT

D5 446 4,460 679 424 4,884

D7 686 6,860 1338 836 7,696

D9 1,220 12,200 2748 1,717 13,917

Cyclone V SE

A2 140 1,400 221 138 1,538

A4 270 2,700 370 231 2,460

A5 397 3,970 768 480 4,450

A6 557 5,570 994 621 5,761

Cyclone V SX

C2 140 1,400 221 138 1,538

C4 270 2,700 370 231 2,460

C5 397 3,970 768 480 4,450

C6 557 5,570 994 621 5,761

Cyclone V ST D5 397 3,970 768 480 4,450

D6 557 5,570 994 621 5,761

Embedded Memory Configurations

Table 19: Supported Embedded Memory Block Configurations for Cyclone V Devices

This table lists the maximum configurations supported for the embedded memory blocks. The information is

applicable only to the single-port RAM and ROM modes.

Memory Block Depth (bits) Programmable Width

MLAB 32 x16, x18, or x20

CV-51001

2016.06.10 Embedded Memory Capacity in Cyclone V Devices 23

Cyclone V Device Overview Altera Corporation

Send Feedback

Memory Block Depth (bits) Programmable Width

M10K

256 x40 or x32

512 x20 or x16

1K x10 or x8

2K x5 or x4

4K x2

8K x1

Clock Networks and PLL Clock Sources

550 MHz Cyclone V devices have 16 global clock networks capable of up to operation. The clock network

architecture is based on Altera's global, quadrant, and peripheral clock structure. This clock structure is

supported by dedicated clock input pins and fractional PLLs.

Note: To reduce power consumption, the Quartus Prime software identifies all unused sections of the

clock network and powers them down.

PLL Features

The PLLs in the Cyclone V devices support the following features:

• Frequency synthesis

• On-chip clock deskew

• Jitter attenuation

• Programmable output clock duty cycles

• PLL cascading

• Reference clock switchover

• Programmable bandwidth

• User-mode reconfiguration of PLLs

• Low power mode for each fractional PLL

• Dynamic phase shift

• Direct, source synchronous, zero delay buffer, external feedback, and LVDS compensation modes

Fractional PLL

In addition to integer PLLs, the Cyclone V devices use a fractional PLL architecture. The devices have up

to eight PLLs, each with nine output counters. You can use the output counters to reduce PLL usage in

two ways:

• Reduce the number of oscillators that are required on your board by using fractional PLLs

• Reduce the number of clock pins that are used in the device by synthesizing multiple clock frequencies

from a single reference clock source

If you use the fractional PLL mode, you can use the PLLs for precision fractional-N frequency synthesis—

removing the need for off-chip reference clock sources in your design.

The transceiver fractional PLLs that are not used by the transceiver I/Os can be used as general purpose

fractional PLLs by the FPGA fabric.

24 Clock Networks and PLL Clock Sources CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

FPGA General Purpose I/O

Cyclone V devices offer highly configurable GPIOs. The following list describes the features of the GPIOs:

• Programmable bus hold and weak pull-up

• LVDS output buffer with programmable differential output voltage (VOD ) and programmable pre-

emphasis

• On-chip parallel termination (RT OCT) for all I/O banks with OCT calibration to limit the termination

impedance variation

• On-chip dynamic termination that has the ability to swap between series and parallel termination,

depending on whether there is read or write on a common bus for signal integrity

• Easy timing closure support using the hard read FIFO in the input register path, and delay-locked loop

(DLL) delay chain with fine and coarse architecture

PCIe Gen1 and Gen2 Hard IP

Cyclone V GX, GT, SX, and ST devices contain PCIe hard IP that is designed for performance and

ease-of-use. The PCIe hard IP consists of the MAC, data link, and transaction layers.

The PCIe hard IP supports PCIe Gen2 and Gen1 end point and root port for up to x4 lane configuration.

The PCIe Gen2 x4 support is PCIe-compatible.

The PCIe endpoint support includes multifunction support for up to eight functions, as shown in the

following figure. The integrated multifunction support reduces the FPGA logic requirements by up to

20,000 LEs for PCIe designs that require multiple peripherals.

Figure 9: PCIe Multifunction for Cyclone V Devices

PCIe Link

External System FPGA Device

Host CPU

Memory

Controller

Root

Complex

Local

Peripheral 1

Local

Peripheral 2

PCIe RP

PCIe EP

CAN

GbE

ATA

Bridge

to PCIe

SPI

GPIO

I2C

USB

The Cyclone V PCIe hard IP operates independently from the core logic. This independent operation

allows the PCIe link to wake up and complete link training in less than 100 ms while the Cyclone V device

completes loading the programming file for the rest of the device.

In addition, the PCIe hard IP in the Cyclone V device provides improved end-to-end datapath protection

using ECC.

CV-51001

2016.06.10 FPGA General Purpose I/O 25

Cyclone V Device Overview Altera Corporation

Send Feedback

External Memory Interface

This section provides an overview of the external memory interface in Cyclone V devices.

Hard and Soft Memory Controllers

Cyclone V devices support up to two hard memory controllers for DDR3, DDR2, and LPDDR2 SDRAM

devices. Each controller supports 8 to 32 bit components of up to 4 gigabits (Gb) in density with two chip

selects and optional ECC. For the Cyclone V SoC devices, an additional hard memory controller in the

HPS supports DDR3, DDR2, and LPDDR2 SDRAM devices.

All Cyclone V devices support soft memory controllers for DDR3, DDR2, and LPDDR2 SDRAM devices

for maximum flexibility.

External Memory Performance

Table 20: External Memory Interface Performance in Cyclone V Devices

The maximum and minimum operating frequencies depend on the memory interface standards and the

supported delay-locked loop (DLL) frequency listed in the device datasheet.

Interface Voltage

(V)

Maximum Frequency (MHz) Minimum Frequency (MHz)

Hard Controller Soft Controller

DDR3 SDRAM 1.5 400 303 303

1.35 400 303 303

DDR2 SDRAM 1.8 400 300 167

LPDDR2

SDRAM 1.2 333 300 167

Related Information

External Memory Interface Spec Estimator

For the latest information and to estimate the external memory system performance specification, use

Altera's External Memory Interface Spec Estimator tool.

HPS External Memory Performance

Table 21: HPS External Memory Interface Performance

The hard processor system (HPS) is available in Cyclone V SoC devices only.

Interface Voltage (V) HPS Hard Controller (MHz)

DDR3 SDRAM 1.5 400

1.35 400

DDR2 SDRAM 1.8 400

LPDDR2 SDRAM 1.2 333

26 External Memory Interface CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Related Information

External Memory Interface Spec Estimator

For the latest information and to estimate the external memory system performance specification, use

Altera's External Memory Interface Spec Estimator tool.

Low-Power Serial Transceivers

Cyclone V devices deliver the industry’s lowest power 6.144 Gbps transceivers at an estimated 88 mW

maximum power consumption per channel. Cyclone V transceivers are designed to be compliant with a

wide range of protocols and data rates.

Transceiver Channels

The transceivers are positioned on the left outer edge of the device. The transceiver channels consist of the

physical medium attachment (PMA), physical coding sublayer (PCS), and clock networks.

Figure 10: Device Chip Overview for Cyclone V GX and GT Devices

The figure shows a Cyclone V FPGA with transceivers. Different Cyclone V devices may have a different

floorplans than the one shown here.

I/O, LVDS, and Memory Interface

Transceiver PMA Blocks

Fractional PLLs

Hard PCS Blocks

Fractional PLL

Fractional PLLs

PCIe Hard IP Blocks

Hard Memory Controller

Core Logic Fabric and MLABs

Variable-Precision DSP Blocks

M10K Internal Memory Blocks

Transceiver

PMA

Transceiver

PMA

Transceiver

PMA Hard

PCS

Hard

PCS

Hard

PCS

Clock Networks

Transceiver

Individual Channels

CV-51001

2016.06.10 Low-Power Serial Transceivers 27

Cyclone V Device Overview Altera Corporation

Send Feedback

PMA Features

To prevent core and I/O noise from coupling into the transceivers, the PMA block is isolated from the rest

of the chip—ensuring optimal signal integrity. For the transceivers, you can use the channel PLL of an

unused receiver PMA as an additional transmit PLL.

Table 22: PMA Features of the Transceivers in Cyclone V Devices

Features Capability

Backplane support Driving capability up to 6.144 Gbps

PLL-based clock recovery Superior jitter tolerance

Programmable deserialization

and word alignment Flexible deserialization width and configurable word alignment pattern

Equalization and pre-emphasis • Up to 14.37 dB of pre-emphasis and up to 4.7 dB of equalization

• No decision feedback equalizer (DFE)

Ring oscillator transmit PLLs 614 Mbps to 6.144 Gbps

Input reference clock range 20 MHz to 400 MHz

Transceiver dynamic reconfigu‐

ration Allows the reconfiguration of a single channel without affecting the

operation of other channels

PCS Features

The Cyclone V core logic connects to the PCS through an 8, 10, 16, 20, 32, or 40 bit interface, depending

on the transceiver data rate and protocol. Cyclone V devices contain PCS hard IP to support PCIe Gen1

and Gen2, Gbps Ethernet (GbE), Serial RapidIO® (SRIO), and Common Public Radio Interface (CPRI).

Most of the standard and proprietary protocols from 614 Mbps to 6.144 Gbps are supported.

Table 23: Transceiver PCS Features for Cyclone V Devices

PCS Support Data Rates

(Gbps)

Transmitter Data Path Feature Receiver Data Path Feature

3-Gbps and 6-Gbps

Basic 0.614 to 6.144 • Phase compensation FIFO

• Byte serializer

• 8B/10B encoder

• Transmitter bit-slip

• Word aligner

• Deskew FIFO

• Rate-match FIFO

• 8B/10B decoder

• Byte deserializer

• Byte ordering

• Receiver phase compensa‐

tion FIFO

28 PMA Features CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

PCS Support Data Rates

(Gbps)

Transmitter Data Path Feature Receiver Data Path Feature

PCIe Gen1

(x1, x2, x4) 2.5 and 5.0 • Dedicated PCIe PHY IP core

• PIPE 2.0 interface to the core

logic

• Dedicated PCIe PHY IP

core

• PIPE 2.0 interface to the

core logic

PCIe Gen2

( x1, x2, x4)(12)

GbE 1.25 • Custom PHY IP core with

preset feature

• GbE transmitter synchroniza‐

tion state machine

• Custom PHY IP core with

preset feature

• GbE receiver synchroniza‐

tion state machine

XAUI (13) 3.125 • Dedicated XAUI PHY IP core

• XAUI synchronization state

machine for bonding four

channels

• Dedicated XAUI PHY IP

core

• XAUI synchronization

state machine for

realigning four channels

HiGig 3.75

SRIO 1.3 and 2.1 1.25 to 3.125 • Custom PHY IP core with

preset feature

• SRIO version 2.1-compliant

x2 and x4 channel bonding

• Custom PHY IP core with

preset feature

• SRIO version

2.1-compliant x2 and x4

deskew state machine

SDI, SD/HD, and

3G-SDI 0.27(14), 1.485,

and 2.97 Custom PHY IP core with preset

feature Custom PHY IP core with

preset feature

JESD204A 0.3125(15) to

3.125

Serial ATA Gen1 and

Gen2 1.5 and 3.0 • Custom PHY IP core with

preset feature

• Electrical idle

• Custom PHY IP core with

preset feature

• Signal detect

• Wider spread of asynchro‐

nous SSC

(12) PCIe Gen2 is supported for Cyclone V GT and ST devices. The PCIe Gen2 x4 support is PCIe-compatible.

(13) XAUI is supported through the soft PCS.

(14) The 0.27-Gbps data rate is supported using oversampling user logic that you must implement in the FPGA

fabric.

(15) The 0.3125-Gbps data rate is supported using oversampling user logic that you must implement in the

FPGA fabric.

CV-51001

2016.06.10 PCS Features 29

Cyclone V Device Overview Altera Corporation

Send Feedback

PCS Support Data Rates

(Gbps)

Transmitter Data Path Feature Receiver Data Path Feature

CPRI 4.1(16) 0.6144 to 6.144 • Dedicated deterministic

latency PHY IP core

• Transmitter (TX) manual

bit-slip mode

• Dedicated deterministic

latency PHY IP core

• Receiver (RX) determin‐

istic latency state machine

OBSAI RP3 0.768 to

3.072

V-by-One HS Up to 3.75

Custom PHY IP core • Custom PHY IP core

• Wider spread of asynchro‐

nous SSC

DisplayPort 1.2(17) 1.62 and 2.7

SoC with HPS

Each SoC combines an FPGA fabric and an HPS in a single device. This combination delivers the

flexibility of programmable logic with the power and cost savings of hard IP in these ways:

• Reduces board space, system power, and bill of materials cost by eliminating a discrete embedded

processor

• Allows you to differentiate the end product in both hardware and software, and to support virtually

any interface standard

• Extends the product life and revenue through in-field hardware and software updates

HPS Features

The HPS consists of a dual-core ARM Cortex-A9 MPCore processor, a rich set of peripherals, and a

shared multiport SDRAM memory controller, as shown in the following figure.

(16) High-voltage output mode (1000-BASE-CX) is not supported.

(17) Pending characterization.

30 SoC with HPS CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Figure 11: HPS with Dual-Core ARM Cortex-A9 MPCore Processor

FPGA Fabric

HPS

HPS-to-FPGA Lightweight

HPS-to-FPGA

FPGA-to-HPS FPGA-to-HPS SDRAM

Configuration

Controller

FPGA

Manager

64 KB

On-Chip RAM

64 KB

Boot ROM

Level 3

Interconnect

Ethernet

MAC (2x)

USB

OTG (2x)

NAND Flash

Controller

SD/MMC

Controller

DMA

Controller STM

ETR

(Trace)

Debug

Access Port ARM Cortex-A9 MPCore

MPU Subsystem

CPU0

ARM Cortex-A9

with NEON/FPU,

32 KB Instruction Cache,

32 KB Data Cache, and

Memory Management

Unit

CPU1

ARM Cortex-A9

with NEON/FPU,

32 KB Instruction Cache,

32 KB Data Cache, and

Memory Management

Unit

SCUACP

Level 2 Cache (512 KB)

Multiport

DDR SDRAM

Controller

with

Optional ECC

Peripherals

(UART, Timer, I2C, Watchdog Timer, GPIO, SPI, Clock Manager, Reset Manager, Scan Manager, System Manager, and Quad

SPI Flash Controller)

System Peripherals and Debug Access Port

Each Ethernet MAC, USB OTG, NAND flash controller, and SD/MMC controller module has an

integrated DMA controller. For modules without an integrated DMA controller, an additional DMA

controller module provides up to eight channels of high-bandwidth data transfers. Peripherals that

communicate off-chip are multiplexed with other peripherals at the HPS pin level. This allows you to

choose which peripherals to interface with other devices on your PCB.

The debug access port provides interfaces to industry standard JTAG debug probes and supports ARM

CoreSight debug and core traces to facilitate software development.

CV-51001

2016.06.10 System Peripherals and Debug Access Port 31

Cyclone V Device Overview Altera Corporation

Send Feedback

HPS–FPGA AXI Bridges

The HPS–FPGA bridges, which support the Advanced Microcontroller Bus Architecture (AMBA®)

Advanced eXtensible Interface (AXI™) specifications, consist of the following bridges:

• FPGA-to-HPS AXI bridge—a high-performance bus supporting 32, 64, and 128 bit data widths that

allows the FPGA fabric to issue transactions to slaves in the HPS.

• HPS-to-FPGA AXI bridge—a high-performance bus supporting 32, 64, and 128 bit data widths that

allows the HPS to issue transactions to slaves in the FPGA fabric.

• Lightweight HPS-to-FPGA AXI bridge—a lower latency 32 bit width bus that allows the HPS to issue

transactions to slaves in the FPGA fabric. This bridge is primarily used for control and status register

(CSR) accesses to peripherals in the FPGA fabric.

The HPS–FPGA AXI bridges allow masters in the FPGA fabric to communicate with slaves in the HPS

logic, and vice versa. For example, the HPS-to-FPGA AXI bridge allows you to share memories instanti‐

ated in the FPGA fabric with one or both microprocessors in the HPS, while the FPGA-to-HPS AXI

bridge allows logic in the FPGA fabric to access the memory and peripherals in the HPS.

Each HPS–FPGA bridge also provides asynchronous clock crossing for data transferred between the

FPGA fabric and the HPS.

HPS SDRAM Controller Subsystem

The HPS SDRAM controller subsystem contains a multiport SDRAM controller and DDR PHY that are

shared between the FPGA fabric (through the FPGA-to-HPS SDRAM interface), the level 2 (L2) cache,

and the level 3 (L3) system interconnect. The FPGA-to-HPS SDRAM interface supports AMBA AXI and

Avalon® Memory-Mapped (Avalon-MM) interface standards, and provides up to six individual ports for

access by masters implemented in the FPGA fabric.

To maximize memory performance, the SDRAM controller subsystem supports command and data

reordering, deficit round-robin arbitration with aging, and high-priority bypass features. The SDRAM

controller subsystem supports DDR2, DDR3, or LPDDR2 devices up to 4 Gb in density operating at up to

400 MHz (800 Mbps data rate).

FPGA Configuration and Processor Booting

The FPGA fabric and HPS in the SoC are powered independently. You can reduce the clock frequencies

or gate the clocks to reduce dynamic power, or shut down the entire FPGA fabric to reduce total system

power.

You can configure the FPGA fabric and boot the HPS independently, in any order, providing you with

more design flexibility:

• You can boot the HPS independently. After the HPS is running, the HPS can fully or partially

reconfigure the FPGA fabric at any time under software control. The HPS can also configure other

FPGAs on the board through the FPGA configuration controller.

• You can power up both the HPS and the FPGA fabric together, configure the FPGA fabric first, and

then boot the HPS from memory accessible to the FPGA fabric.

Note: Although the FPGA fabric and HPS are on separate power domains, the HPS must remain

powered up during operation while the FPGA fabric can be powered up or down as required.

32 HPS–FPGA AXI Bridges CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Related Information

Cyclone V Device Family Pin Connection Guidelines

Provides detailed information about power supply pin connection guidelines and power regulator

sharing.

Hardware and Software Development

For hardware development, you can configure the HPS and connect your soft logic in the FPGA fabric to

the HPS interfaces using the Qsys system integration tool in the Quartus Prime software.

For software development, the ARM-based SoC devices inherit the rich software development ecosystem

available for the ARM Cortex-A9 MPCore processor. The software development process for Altera SoCs

follows the same steps as those for other SoC devices from other manufacturers. Support for Linux,

VxWorks®, and other operating systems is available for the SoCs. For more information on the operating

systems support availability, contact the Altera sales team.

You can begin device-specific firmware and software development on the Altera SoC Virtual Target. The

Virtual Target is a fast PC-based functional simulation of a target development system—a model of a

complete development board that runs on a PC. The Virtual Target enables the development of

device-specific production software that can run unmodified on actual hardware.

Related Information

Altera Worldwide Sales Support

Dynamic and Partial Reconfiguration

The Cyclone V devices support dynamic reconfiguration and partial reconfiguration.

Dynamic Reconfiguration

The dynamic reconfiguration feature allows you to dynamically change the transceiver data rates, PMA

settings, or protocols of a channel, without affecting data transfer on adjacent channels. This feature is

ideal for applications that require on-the-fly multiprotocol or multirate support. You can reconfigure the

PMA and PCS blocks with dynamic reconfiguration.

Partial Reconfiguration

Note: The partial reconfiguration feature is available for Cyclone V E, GX, SE, and SX devices with the

"SC" suffix in the part number. For device availability and ordering, contact your local Altera sales

representatives.

Partial reconfiguration allows you to reconfigure part of the device while other sections of the device

remain operational. This capability is important in systems with critical uptime requirements because it

allows you to make updates or adjust functionality without disrupting services.

Apart from lowering cost and power consumption, partial reconfiguration increases the effective logic

density of the device because placing device functions that do not operate simultaneously is not necessary.

Instead, you can store these functions in external memory and load them whenever the functions are

required. This capability reduces the size of the device because it allows multiple applications on a single

device—saving the board space and reducing the power consumption.

CV-51001

2016.06.10 Hardware and Software Development 33

Cyclone V Device Overview Altera Corporation

Send Feedback

Altera simplifies the time-intensive task of partial reconfiguration by building this capability on top of the

proven incremental compile and design flow in the Quartus Prime design software. With the Altera®

solution, you do not need to know all the intricate device architecture details to perform a partial reconfi‐

guration.

Partial reconfiguration is supported through the FPP x16 configuration interface. You can seamlessly use

partial reconfiguration in tandem with dynamic reconfiguration to enable simultaneous partial reconfigu‐

ration of both the device core and transceivers.

Enhanced Configuration and Configuration via Protocol

Cyclone V devices support 1.8 V, 2.5 V, 3.0 V, and 3.3 V programming voltages and several configuration

modes.

Table 24: Configuration Modes and Features Supported by Cyclone V Devices

Mode Data

Width Max

Clock

Rate

(MHz)

Max Data

Rate

(Mbps)

Decompres‐

sion Design

Security Partial

Reconfigu‐

ration(18)

Remote System

Update

AS through the

EPCS and EPCQ

serial configura‐

tion device

1 bit, 4

bits 100 — Yes Yes — Yes

PS through

CPLD or

external

microcontroller

1 bit 125 125 Yes Yes — —

FPP 8 bits 125 — Yes Yes — Parallel flash loader

16 bits 125 — Yes Yes Yes

CvP (PCIe) x1, x2,

and x4

lanes

— — Yes Yes Yes —

JTAG 1 bit 33 33 — — — —

Instead of using an external flash or ROM, you can configure the Cyclone V devices through PCIe using

CvP. The CvP mode offers the fastest configuration rate and flexibility with the easy-to-use PCIe hard IP

block interface. The Cyclone V CvP implementation conforms to the PCIe 100 ms power-up-to-active

time requirement.

Related Information

Configuration via Protocol (CvP) Implementation in Altera FPGAs User Guide

Provides more information about CvP.

(18) The partial reconfiguration feature is available for Cyclone V E, GX, SE, and SX devices with the "SC" suffix

in the part number. For device availability and ordering, contact your local Altera sales representatives.

34 Enhanced Configuration and Configuration via Protocol CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Power Management

Leveraging the FPGA architectural features, process technology advancements, and transceivers that are

designed for power efficiency, the Cyclone V devices consume less power than previous generation

Cyclone FPGAs:

• Total device core power consumption—less by up to 40%.

• Transceiver channel power consumption—less by up to 50%.

Additionally, Cyclone V devices contain several hard IP blocks that reduce logic resources and deliver

substantial power savings of up to 25% less power than equivalent soft implementations.

Document Revision History

Date Version Changes

June 2016 2016.06.10 Updated Cyclone V GT speed grade to –7 in Sample Ordering Code and

Available Options for Cyclone V GT Devices diagram.

December

2015 2015.12.21 • Added descriptions to package plan tables for Cyclone V GT and ST

devices.

• Changed instances of Quartus II to Quartus Prime.

CV-51001

2016.06.10 Power Management 35

Cyclone V Device Overview Altera Corporation

Send Feedback

Date Version Changes

June 2015 2015.06.12 • Replaced a note to partial reconfiguration feature. Note: The partial

reconfiguration feature is available for Cyclone V E, GX, SE, and SX

devices with the "SC" suffix in the part number. For device availability

and ordering, contact your local Altera sales representatives.

• Updated logic elements (LE) (K) for the following devices:

• Cyclone V E A7: Updated from 149.5 to 150

• Cyclone V GX C3: Updated from 35.5 to 36

• Cyclone V GX C7: Updated from 149.7 to 150

• Cyclone V GT D7: Updated from 149.5 to 150

• Updated MLAB (Kb) in Maximum Resource Counts for

Cyclone V GX Devices table as follows:

• Cyclone V GX C3: Updated from 291 to 182

• Cyclone V GX C4: Updated from 678 to 424

• Cyclone V GX C5: Updated from 678 to 424

• Cyclone V GX C7: Updated from 1,338 to 836

• Cyclone V GX C9: Updated from 2,748 to 1,717

• Updated MLAB RAM Bit (Kb) in Embedded Memory Capacity and

Distribution in Cyclone V Devices table as follows:

• Cyclone V GX C3: Updated from 181 to 182

• Cyclone V GX C4: Updated from 295 to 424

• Updated Total RAM Bit (Kb) in Embedded Memory Capacity and

Distribution in Cyclone V Devices table as follows:

• Cyclone V GX C3: Updated from 1,531 to 1,532

• Cyclone V GX C4: Updated from 2,795 to 2,924

• Updated MLAB Block count in Embedded Memory Capacity and

Distribution in Cyclone V Devices table as follows:

• Cyclone V GX C4: Updated from 472 to 678

• Cyclone V GX C5: Updated from 679 to 678

March 2015 2015.03.31 • Added internal scrubbing feature under configuration in Summary of

Features for Cyclone V Devices table.

• Added optional suffix "SC: Internal scrubbing support" to the

following diagrams:

• Sample Ordering Code and Available Options for Cyclone V E

Devices

• Sample Ordering Code and Available Options for Cyclone V GX

Devices

• Sample Ordering Code and Available Options for Cyclone V SE

Devices

• Sample Ordering Code and Available Options for Cyclone V SX

Devices

36 Document Revision History CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Date Version Changes

January 2015 2015.01.23 • Updated Sample Ordering Code and Available Options for Cyclone V

ST Devices figure because Cyclone V ST devices are only available in I

temperature grade and –7 speed grade.

• Operating Temperature: Removed C and A temperature grades

• FPGA Fabric Speed Grade: Removed –6 and –8 speed grades

• Updated the transceiver specification for Cyclone V ST from 5 Gbps

to 6.144 Gbps:

• Device Variants for the Cyclone V Device Family table

• Sample Ordering Code and Available Options for Cyclone V ST

Devices figure

• Maximum Resource Counts for Cyclone V ST Devices

• Updated Maximum Resource Counts for Cyclone V GX Devices table

for Cyclone V GX G3 devices.

• Logic elements (LE) (K): Updated from 35.7 to 35.5

• Variable-precision DSP block: Updated from 51 to 57

• 18 x 18 multiplier: Updated from 102 to 114

• Updated Number of Multipliers in Cyclone V Devices table for

Cyclone V GX G3 devices.

• Variableprecision DSP Block: Updated from 51 to 57

• 9 x 9 Multiplier: Updated from 153 to 171

• 18 x 18 Multiplier: Updated from 102 to 114

• 27 x 27 Multiplier: Updated from 51 to 57

• 18 x 18 Multiplier Adder Mode: Updated from 51 to 57

• 18 x 18 Multiplier Adder Summed with 36 bit Input: Updated

from 51 to 57

• Updated Embedded Memory Capacity and Distribution in Cyclone V

Devices table for Cyclone V GX G3 devices.

• M10K block: Updated from 119 to 135

• M10K RAM bit (Kb): Updated from 1,190 to 1,350

• MLAB block: Updated from 255 to 291

• MLAB RAM bit (Kb): Updated from 159 to 181

• Total RAM bit (Kb): Updated from 1,349 to 1,531

October 2014 2014.10.06 Added a footnote to the "Transceiver PCS Features for Cyclone V

Devices" table to show that PCIe Gen2 is supported for Cyclone V GT

and ST devices.

July 2014 2014.07.07 Updated the I/O vertical migration figure to clarify the migration

capability of Cyclone V SE and SX devices.

CV-51001

2016.06.10 Document Revision History 37

Cyclone V Device Overview Altera Corporation

Send Feedback

Date Version Changes

December

2013 2013.12.26 • Corrected single or dual-core ARM Cortex-A9 MPCore processor-up

to 925 MHz from 800 MHz.

• Removed "Preliminary" texts from Ordering Code figures, Maximum

Resources, Package Plan and I/O Vertical Migration tables.

• Removed the note "The number of GPIOs does not include

transceiver I/Os. In the Quartus II software, the number of user I/Os

includes transceiver I/Os." for GPIOs in the Maximum Resource

Counts table for Cyclone V E and SE.

• Added link to Altera Product Selector for each device variant.

• Updated Embedded Hard IPs for Cyclone V GT devices to indicate

Maximum 2 hard PCIe and 2 hard memory controllers.

• Added leaded package options.

• Removed the note "The number of PLLs includes general-purpose

fractional PLLs and transceiver fractional PLLs." for all PLLs in the

Maximum Resource Counts table.

• Corrected max LVDS counts for transmitter and receiver for Cyclone

V E A5 device from 84 to 60.

• Corrected max LVDS counts for transmitter and receiver for Cyclone

V E A9 device from 140 to 120.

• Corrected variable-precision DSP block, 27 x 27 multiplier, 18 x 18

multiplier adder mode and 18 x 18 multiplier adder summed with 36

bit input for Cyclone V SE devices from 58 to 84.

• Corrected 18 x 18 multiplier for Cyclone V SE devices from 116 to

168.

• Corrected 9 x 9 multiplier for Cyclone V SE devices from 174 to 252.

• Corrected LVDS transmitter for Cyclone V SE A2 and A4 as well as

SX C2 and C4 devices from 31 to 32.

• Corrected LVDS receiver for Cyclone V SE A2 and A4 as well as SX

C2 and C4 devices from 35 to 37.

• Corrected transceiver speed grade for Cyclone V ST devices ordering

code from 4 to 5.

• Updated the DDR3 SDRAM for the maximum frequency's soft

controller and the minimum frequency from 300 to 303 for voltage

1.35V.

• Added links to Altera's External Memory Spec Estimator tool to the

topics listing the external memory interface performance.

• Corrected XAUI is supported through the soft PCS in the PCS

features for Cyclone V.

• Added decompression support for the CvP configuration mode.

38 Document Revision History CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Date Version Changes

May 2013 2013.05.06 • Added link to the known document issues in the Knowledge Base.

• Moved all links to the Related Information section of respective topics

for easy reference.

• Corrected the title to the PCIe hard IP topic. Cyclone V devices

support only PCIe Gen1 and Gen2.

• Updated Supporting Feature in Table 1 of Increased bandwidth

capacity to '6.144 Gbps'.

• Updated Description in Table 2 of Low-power high-speed serial

interface to '6.144 Gbps'.

• Updated Description in Table 3 of Cyclone V GT to '6.144 Gbps'.

• Updated the M386 package to M383 for Figure 1, Figure 2 and Figure

• Updated Figure 2 and Figure 3 for Transceiver Count by adding 'F :

4'.

• Updated LVDS in the Maximum Resource Counts tables to include

Transmitter and Receiver values.

• Updated the package plan with M383 for the Cyclone V E device.

• Removed the M301 and M383 packages from the Cyclone V GX C4

device.

• Updated the GPIO count to '129' for the M301 package of the

Cyclone V GX C5 device.

• Updated 5 Gbps to '6.144 Gbps' for Cyclone V GT device.

• Updated HPS I/O for U484 (19 mm) in Table 11 with '151' for A2,

A4, A5 and A6.

• Updated Memory (Kb) for Maximum Resource Counts for Cyclone V

SE A4 and A6, SX C4 and C6, ST D6 devices.

• Updated FPGA PLL for Maximum Resource Counts for Cyclone V

SE A2, SX C2, devices.

• Removed '36 x 36' from the Variable-Precision DSP Block.

• Updated Variable-precision DSP Blocks and 18 x 18 Multiplier for

Maximum Resource Counts for Cyclone V SX C4 device.

• Updated the HPS I/O counts for Cyclone V SE, SX, and ST devices.

• Updated Figure 7 which shows the I/O vertical migration table.

• Updated Table 17 for Cyclone V SX C4 device.

• Updated Embedded Memory Capacity and Distribution table for

Cyclone V SE A4 and A6, SX C4 and C6, ST D6 devices.

• Removed 'Counter reconfiguration' from the PLL Features.

• Updated Low-Power Serial Transceivers by replacing 5 Gbps with

6.144 Gbps.

• Removed 'Distributed Memory' symbol.

• Updated the Capability in Table 22 of Backplane support to

'6.144 Gbps'.

CV-51001

2016.06.10 Document Revision History 39

Cyclone V Device Overview Altera Corporation

Send Feedback

Date Version Changes

• Updated Capability in Table 22 of Ring oscillator transmit PLLs with

6.144 Gbps.

• Updated the PCS Support in Table 23 from 5 Gbps to '6 Gbps'.

• Updated the Data Rates (Gbps) in Table 23 of 3 Gbps and 6 Gbps

Basic to '6.144 Gbps'.

• Updated the Data Rates (Gbps) in Table 23 of CPRI 4.1 to

'6.144 Gbps'.

• Clarified that partial reconfiguration is an advanced feature. Contact

Altera for support of the feature.

December

2012 2012.12.28 • Updated the pin counts for the MBGA packages.

• Updated the GPIO and transceiver counts for the MBGA packages.

• Updated the GPIO counts for the U484 package of the Cyclone V E

A9, GX C9, and GT D9 devices.

• Updated the vertical migration table for vertical migration of the

U484 packages.

• Updated the MLAB supported programmable widths at 32 bits depth.

November

2012 2012.11.19 • Added new MBGA packages and additional U484 packages for

Cyclone V E, GX, and GT.

• Added ordering code for five-transceiver devices for Cyclone V GT

and ST.

• Updated the vertical migration table to add MBGA packages.

• Added performance information for HPS memory controller.

• Removed DDR3U support.

• Updated Cyclone V ST speed grade information.

• Added information on maximum transceiver channel usage restric‐

tions for PCI Gen2 and CPRI at 4.9152 Gbps transmit jitter

compliance.

• Added note on the differences between GPIO reported in Overview

with User I/O numbers shown in the Quartus II software.

• Updated template.

July 2012 2.1 Added support for PCIe Gen2 x4 lane configuration (PCIe-compatible)

40 Document Revision History CV-51001

2016.06.10

Altera Corporation Cyclone V Device Overview

Send Feedback

Date Version Changes

June 2012 2.0 • Restructured the document.

• Added the “Embedded Memory Capacity” and “Embedded Memory

Configurations” sections.

• Added Table 1, Table 3, Table 16, Table 19, and Table 20.

• Updated Table 2, Table 4, Table 5, Table 6, Table 7, Table 8, Table 9,

Table 10, Table 11, Table 12, Table 13, Table 14, Table 17, and Table

18.

• Updated Figure 1, Figure 2, Figure 3, Figure 4, Figure 5, Figure 6, and

Figure 10.

• Updated the “FPGA Configuration and Processor Booting” and

“Hardware and Software Development” sections.

• Text edits throughout the document.

February 2012 1.2 • Updated Table 1–2, Table 1–3, and Table 1–6.

• Updated “Cyclone V Family Plan” on page 1–4 and “Clock Networks

and PLL Clock Sources” on page 1–15.

• Updated Figure 1–1 and Figure 1–6.

November

2011 1.1 • Updated Table 1–1, Table 1–2, Table 1–3, Table 1–4, Table 1–5, and

Table 1–6.

• Updated Figure 1–4, Figure 1–5, Figure 1–6, Figure 1–7, and Figure

1–8.

• Updated “System Peripherals” on page 1–18, “HPS–FPGA AXI

Bridges” on page 1–19, “HPS SDRAM Controller Subsystem” on page

1–19, “FPGA Configuration and Processor Booting” on page 1–19,

and “Hardware and Software Development” on page 1–20.

• Minor text edits.

October 2011 1.0 Initial release.

CV-51001

2016.06.10 Document Revision History 41

Cyclone V Device Overview Altera Corporation

Send Feedback

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Altera:

5CSEBA5U19A7N 5CSEBA5U19C6N 5CSEBA5U19C7N 5CSEBA5U19C7SN 5CSEBA5U19C8N

5CSEBA5U19C8SN 5CSEBA5U19I7N 5CSEBA5U19I7SN 5CSEBA5U23A7N 5CSEBA5U23C6N 5CSEBA5U23C7N

5CSEBA5U23C7SN 5CSEBA5U23C8N 5CSEBA5U23C8SN 5CSEBA5U23I7N 5CSEBA5U23I7SN

5CSEBA6U19A7N 5CSEBA6U19C6N 5CSEBA6U19C7N 5CSEBA6U19C7SN 5CSEBA6U19C8N

5CSEBA6U19C8SN 5CSEBA6U19I7N 5CSEBA6U19I7SN 5CSEBA6U23A7N 5CSEBA6U23C6N 5CSEBA6U23C7N

5CSEBA6U23C7SN 5CSEBA6U23C8N 5CSEBA6U23C8SN 5CSEBA6U23I7N 5CSEBA6U23I7SN

5CSEMA5F31A7N 5CSEMA5F31C6N 5CSEMA5F31C7N 5CSEMA5F31C8N 5CSEMA5F31I7N 5CSEMA5U23A7N

5CSEMA5U23C6N 5CSEMA5U23C7N 5CSEMA5U23C8N 5CSEMA5U23I7N 5CSEMA6F31A7N 5CSEMA6F31C6N

5CSEMA6F31C7N 5CSEMA6F31C8N 5CSEMA6F31I7N 5CSEMA6U23A7N 5CSEMA6U23C6N

5CSEMA6U23C7N 5CSEMA6U23C8N 5CSEMA6U23I7N 5CSTFD5D5F31I7N 5CSTFD6D5F31I7N

5CSXFC5C6U23A7N 5CSXFC5C6U23C6N 5CSXFC5C6U23C7N 5CSXFC5C6U23C8N 5CSXFC5C6U23I7N

5CSXFC5D6F31C6N 5CSXFC5D6F31C7N 5CSXFC5D6F31C8N 5CSXFC5D6F31I7N 5CSXFC6C6U23A7N

5CSXFC6C6U23C6N 5CSXFC6C6U23C7N 5CSXFC6C6U23C8N 5CSXFC6C6U23I7N 5CSXFC6D6F31C6N

5CSXFC6D6F31C7N 5CSXFC6D6F31C8N 5CSXFC6D6F31I7N 5CGXBC4C6F23C7N 5CEFA5F23C8N

5CEFA7F31I7N 5CGXFC9E7F31C8N 5CGTFD9E5F35I7N 5CGXFC5C6U19A7N 5CGXFC7D6F31C6N

5CGTFD5C5F23I7 5CEBA9F23C8N 5CGTFD9E5F31C7N 5CEFA7U19I7 5CEFA7F31C7N 5CEFA2F23C6N

5CEFA7M15C7N 5CEFA5M13C6N 5CGXFC3B7U19C8N 5CGXFC7B6M15I7N 5CGXFC7C6F23I7N

5CGXBC9C7F23C8N 5CGXFC9C6F23I7N 5CEBA2F17C8N 5CEBA9F31C7N 5CGTFD7D5F27I7N

5CGXFC4F7M11C8N 5CGXFC9D6F27I7N 5CGXBC4C7F23C8N 5CGXFC3B6U15A7N 5CEFA9F23C7N