ISL6406MR, ISL6406MV Data Sheet November 11, 2011 Enhanced Product (EP) Single Synchronous Buck Pulse-Width Modulation (PWM) Controller FN6613.1 Features * Specifications per DLA VID V62/08610 The ISL6406MREP and ISL6406MVEP are adjustable frequency, synchronous buck switching regulators optimized for generating lower voltages for distributed DC/DC architectures. Both devices feature an adjustable output voltage. Designed to drive N-Channel MOSFETs in a synchronous buck topology, the ISL6406MREP and ISL6406MVEP integrate the control, output adjustment and protection functions into a single package. * Full Mil-Temp Electrical Performance from -55C to +125C * Controlled Baseline with One Wafer Fabrication Site and One Assembly/Test Site * Full Homogeneous Lot Processing in Wafer Fab * No Combination of Wafer Fabrication Lots in Assembly * Full Traceability Through Assembly and Test by Date/Trace Code Assignment * Enhanced Process Change Notification The ISL6406MREP and ISL6406MVEP provide simple, single feedback loop, voltage-mode control with fast transient response. The output voltage can be precisely regulated to as low as 0.8V. The error amplifier features a 15MHz gain-bandwidth product and 6V/s slew rate which enables high converter bandwidth for fast transient performance. * Enhanced Obsolescence Management Protection from overcurrent conditions is provided by monitoring the rDS(ON) of the upper MOSFET to inhibit PWM operation appropriately. This approach simplifies the implementation and improves efficiency by eliminating the need for a current sense resistor. * Simple Single-Loop Control Design - Voltage-Mode PWM Control The wide programmable switching frequency range of 100kHz to 700kHz allows the use of small surface mount inductors and capacitors. The device also provides external frequency synchronization making it an ideal choice for DC/DC converter applications. * Eliminates Need for Up-Screening a COTS Component * Operates from 3.3V/5V Input * 0.8V to VIN Output Range - 0.8V Internal Reference - 2.1% Reference Accuracy Over-Temperature * Fast Transient Response - High-Bandwidth Error Amplifier * Lossless, Programmable Overcurrent Protection - Uses Upper MOSFET's rDS(on) * Programmable Switching Frequency 100kHz to 700kHz * External Frequency Synchronization * Internal Soft-Start Device Information The specifications for an Enhanced Product (EP) device are defined in a Vendor Item Drawing (VID), which is controlled by the Defense Logistics Agency (DLA). "Hot-links" to the applicable VID and other supporting application information are provided on our website. Applications * 3V/5V DC/DC Converter Modules * Distributed DC/DC 3.3V, 2.5V and 1.8V Power Architectures for DSP, Logic, and Memory * Power Supplies for Microprocessors - PCs - Embedded Controllers * Memory Supplies * Personal Computer Peripherals 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2007, 2011. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL6406MR, ISL6406MV Pinouts ISL6406MVEP (16 LD TSSOP) TOP VIEW LGATE GND UGATE BOOT ISL6406MREP (16 LD QFN) TOP VIEW 16 15 14 13 1 12 PHASE OCSET 2 11 VCC CT1 3 10 CPGND 4 15 BOOT LGATE 2 14 PHASE CPVOUT 3 CPVOUT CT2 16 UGATE GND 1 9 13 VCC OCSET 4 COMP CT1 5 12 CPGND CT2 6 11 COMP RT 7 10 VOUT 9 FB 7 SYNC/EN FB 8 VOUT 6 RT SYNC/EN 8 5 Ordering Information VENDOR PART NUMBER (Notes 1, 2) VENDOR ITEM DRAWING PART MARKING TEMP. RANGE (C) PACKAGE PKG. DWG. # ISL6406MREP V62/08610-01XB 6406MREP -55 to +125 16 Ld 5x5 QFN L16.5x5B ISL6406MREP-TK V62/08610-01XB 6406MREP -55 to +125 16 Ld 5x5 QFN L16.5x5B ISL6406MVEP V62/08610-01YB 6406 MVEP -55 to +125 16 Ld TSSOP M16.173 ISL6406MVEP-TK V62/08610-01YB 6406 MVEP -55 to +125 16 Ld TSSOP M16.173 NOTES: 1. "-TK" suffix IS for 1,000 piece quantity tape and reel. Please refer to TB347 for details on reel specifications. 2. Devices must be procured to the VENDOR PART NUMBER. 2 FN6613.1 November 11, 2011 ISL6406MR, ISL6406MV Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) L16.5x5B 16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220VHHB ISSUE C) MILLIMETERS SYMBOL MIN NOMINAL A 0.80 A1 - A2 - A3 b NOTES 0.90 1.00 - - 0.05 - - 1.00 9 0.20 REF 0.28 D 0.33 9 0.40 5, 8 5.00 BSC D1 D2 MAX - 4.75 BSC 2.95 3.10 9 3.25 7, 8 E 5.00 BSC - E1 4.75 BSC 9 E2 2.95 e 3.10 3.25 7, 8 0.80 BSC - k 0.25 - - - L 0.35 0.60 0.75 8 L1 - - 0.15 10 N 16 2 Nd 4 3 Ne 4 3 P - - 0.60 9 - - 12 9 Rev. 1 10/02 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on each D and E. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Features and dimensions A2, A3, D1, E1, P & are present when Anvil singulation method is used and not present for saw singulation. 10. Depending on the method of lead termination at the edge of the package, a maximum 0.15mm pull back (L1) maybe present. L minus L1 to be equal to or greater than 0.3mm. 3 FN6613.1 November 11, 2011 ISL6406MR, ISL6406MV Thin Shrink Small Outline Plastic Packages (TSSOP) M16.173 N 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE INDEX AREA E 0.25(0.010) M 2 INCHES E1 GAUGE PLANE -B1 B M L 0.05(0.002) -A- SYMBOL MIN MAX MIN MAX NOTES A - 0.043 - 1.10 - A1 3 A D -C- e c 0.10(0.004) C A M 0.05 0.15 - A2 0.033 0.037 0.85 0.95 - b 0.0075 0.012 0.19 0.30 9 c 0.0035 0.008 0.09 0.20 - B S 0.002 D 0.193 0.201 4.90 5.10 3 0.169 0.177 4.30 4.50 4 0.026 BSC E 0.246 L 0.020 N NOTES: 0.006 E1 e A2 A1 b 0.10(0.004) M 0.25 0.010 SEATING PLANE MILLIMETERS 0.65 BSC 0.256 6.25 0.028 0.50 16 0o - 0.70 6 16 8o 0o - 6.50 7 8o 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AB, Issue E. Rev. 1 2/02 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E1" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of "b" dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees) All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 4 FN6613.1 November 11, 2011