REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add vendor CAGE 01295. Add case outline 2. Make change to 1.2.2, 1.3, FIGURE 1, TABLE I, and 6.4. In accordance with NOR 5962-R302-92. 92-12-02 M. A. FRYE B Add generic part number LT1007 as device type 02. Make changes to 1.2.1, FIGURE 1, and TABLE I. Redrawn. 95-05-04 M. A. FRYE C Drawing updated to reflect current requirements. - ro 05-04-25 R. MONNIN D Modify drawing to current requirement. -rrp 10-10-20 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY DONALD R. OSBORNE STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil CHECKED BY D. A. DiCENZO APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A N. A. HAUCK DRAWING APPROVAL DATE 87-08-21 REVISION LEVEL D MICROCIRCUIT, LINEAR, LOW-NOISE OPERATIONAL AMPLIFIER, MONOLITHIC SILICON SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-87578 1 OF 8 5962-E029-11 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87578 01 G A Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 02 LT1007A LT1007 Circuit function Low noise, high speed precision operational amplifier Low noise, high speed precision operational amplifier 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter G P 2 Descriptive designator MACY1-X8 GDIP1-T8 or CDIP2-T8 CQCC1-N20 Terminals Package style 8 8 20 Can Dual-in-line Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage ..................................................................... Input voltage ........................................................................ Differential input .................................................................. Junction temperature (TJ) ................................................... Lead temperature (soldering, 10 seconds) .......................... Storage temperature range ................................................. Thermal resistance, junction-to-case (JC) ......................... 22.0 V dc 22.0 V dc 25 mA +150C +300C -65C to +125C See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case G ............................................................................ 150C/W Case P ............................................................................. 110C/W Case 2 ............................................................................. 65C/W 1.4 Recommended operating conditions. Supply voltage ..................................................................... 15.0 V dc Ambient operating temperature range (TA) ......................... -55C to +125C STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87578 A REVISION LEVEL D SHEET 2 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator "C" shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator "C" shall be replaced with a "Q" or "QML" certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87578 A REVISION LEVEL D SHEET 3 TABLE I. Electrical performance characteristics. Test Conditions -55C TA +125C Symbol VS = 15 V Group A subgroups Device type 4 01 Limits 1/ unless otherwise specified Input offset voltage VOS Min 2/ VOS / Average input offset drift VOS / 02 60 160 3/ 4/ 1,2,3 All 1.0 V/Mo 4/ 1,2,3 01 0.6 V/C 02 1.0 01 30 time temp Input offset current 1 IOS 2,3 1 1 IIB 02 50 85 01 2,3 1 02 2,3 Power dissipation 1 PD -35 +35 -60 +60 -55 +55 -95 +95 01 120 2,3 1 VIN 4/ 1 02 VOUT 1,2,3 RL 2 k mW 140 170 All -11 +11 -10.3 +10.3 01 -12.5 +12.5 02 -12.0 +12.0 2,3 Maximum output voltage swing nA 150 2,3 Input voltage range nA 50 2,3 Input bias current V 60 2,3 Long term input offset voltage stability Max 25 2,3 4 Unit V V See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87578 A REVISION LEVEL D SHEET 4 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA +125C Group A subgroups VS = 15 V Device type unless otherwise specified Common mode rejection ratio CMRR Min 1 VCM = 11 V 2,3 VCM = 10.3 V Power supply rejection ratio Input noise voltage PSRR eN 1,2,3 VS = 4.5 V to 18 V 0.1 Hz to 10 Hz, Limits 1/ 4/ 01 117 02 110 01 112 02 104 01 104 02 100 Unit Max dB dB 7 All 0.13 VPP 7 All 4.5 nV / TA = +25C Input noise voltage density eND fO = 10 Hz, 4/ Hz TA = +25C Input noise current density IND fO = 10 Hz, 7 4/ All 4.0 pA / Hz TA = +25C Slew rate SR RL = 2 k, AVCL 1, 7 All 1.7 V/s 7 All 5.0 MHz TA = +25C Gain bandwidth products GBWP fO = 100 kHz, 4/ TA = +25C Open loop output resistance ZO Large signal voltage gain AVOL VO = 0 V, IO = 0 mA, 7 4/ 2000 TA = +25C 4,5,6 VOUT = 10 V, RL 1 k 01 2.0 02 1.5 V/V 1/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 2/ Input offset voltage measurements are performed by automatic test equipment approximately 0.5 second after application of power. 3/ Long term input offset stability refers to the average trend line of offset voltage vs. time over extended periods after the first 30 days of operations. Excluding the first hour of operation, changes in VOS during the first 30 days are typically 2.5 V. 4/ If not tested, shall be guaranteed to the limits specified in table I herein. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87578 A REVISION LEVEL D SHEET 5 Device types 01 and 02 Case outlines G and P Terminal number 2 Terminal symbol 1 VOS TRIM NC 2 -INPUT VOS TRIM 3 +INPUT NC 4 -VS NC 5 NC -INPUT 6 OUTPUT NC 7 +VS +INPUT 8 VOS TRIM NC 9 --- NC 10 --- -VS 11 --- NC 12 --- NC 13 --- NC 14 --- NC 15 --- OUTPUT 16 --- NC 17 --- +VS 18 --- NC 19 --- NC 20 --- VOS TRIM NC = No connection FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87578 A REVISION LEVEL D SHEET 6 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA = +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87578 A REVISION LEVEL D SHEET 7 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) Subgroups (in accordance with MIL-STD-883, method 5005, table I) --1*,2,3,4,5,6 1,2,3,4,5,6,7 1 * PDA applies to subgroup 1. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0547. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 432183990, or telephone (614) 692-0540. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime -VA. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87578 A REVISION LEVEL D SHEET 8 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 10-10-20 Approved sources of supply for SMD 5962-87578 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-8757801GA 60264 MTLT1007AQH 3/ LT1007AMH/883B 3/ LT1007AMLB 5962-8757801GC 3/ MTL1007AMH/883 5962-8757801PA 60264 MTLT1007AQD8 3/ MTL1007AMJ8/883 3/ LT1007AMJGB 3/ LT1007AMJ8/883B 3/ MTL1007AMD8/883 3/ MTL1007AMJ8/883 60264 MTLT1007AQLS 3/ LT1007AMFKB 5962-87578012C 3/ MTL1007AM2/883 5962-8757802GA 60264 MTLT1007QH 3/ LT1007MH 5962-8757802GC 3/ MTL1007MH/883 5962-8757802PA 60264 MTLT1007QD8 3/ MTL1007MJ8/883 3/ LT1007MJGB 3/ LT1007MJ8 3/ MTL1007MD8/883 3/ MTL1007MJ8/883 5962-8757801PC 5962-87578012A 5962-8757802PC 1 of 2 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-87578022A 60264 MTLT1007QLS 3/ LT1007MFKB 3/ MTL1007AM2/883 5962-87578022C 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number Vendor name and address 60264 Minco Technology Labs, Inc. 1805 Rutherford Lane Austin, TX 78754-5101 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 2 of 2