REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Add vendor CAGE 01295. Add case outline 2. Make change to 1.2.2, 1.3,
FIGURE 1, TABLE I, and 6.4. In accordance with NOR 5962-R302-92.
92-12-02
M. A. FRYE
B
Add generic part number LT1007 as device type 02. Make changes to 1.2.1,
FIGURE 1, and TABLE I. Redrawn.
95-05-04
M. A. FRYE
C
Drawing updated to reflect current requirements. - ro
05-04-25
R. MONNIN
D
Modify drawing to current requirement. -rrp
10-10-20
C. SAFFLE
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS REV D D D D D D D D
OF SHE ETS SHEET 1 2 3 4 5 6 7 8
PMIC N/A PREPARED BY
DONALD R. OSBORNE
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
D. A. DiCENZO
APPRO V ED BY
N. A. HAUCK
MICROCIRCUI T, LINEAR, LOW-NOISE
OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
DRAWING APPROVAL DATE
87-08-21
AMSC N/A
REVISION LEVEL
D SIZE
A CAGE CODE
67268
5962-87578
SHEET 1 OF 8
DSCC FORM 2233
APR 97 5962-E029-11
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87578
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-87578
01
G
A
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Dev ice ty pe(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function
01 LT1007A Low noise, high speed precision operational amplifier
02 LT1007 Low noise, high speed precision operational amplifier
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Pa cka ge sty l e
G MACY1-X8 8 Can
P GDIP1-T8 or CDIP2-T8 8 Dual-in-line
2 CQCC1-N20 20 Square lead le ss chi p carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absol ute maximum rating s.
Supply voltage ..................................................................... ±22.0 V dc
Input voltage ........................................................................ ±22.0 V dc
Differential input .................................................................. ±25 mA
Junction temperature (TJ) ................................................... +150°C
Lead temperature (soldering, 10 seconds) .......................... +300°C
Storage temperature range ................................................. -65°C to +125°C
Thermal resistance, junction-to-case (θJC) ......................... See MIL-STD-1835
Thermal resistance, junction-to-ambient (θJA):
Case G ............................................................................ 150°C/W
Case P ............................................................................. 110°C/W
Case 2 ............................................................................. 65°C/W
1.4 Recom mended operating cond itio ns .
Supply voltage ..................................................................... ±15.0 V dc
Ambient operating temperature range (TA) ......................... -55°C to +125°C
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87578
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitati on or con trac t.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Mic rocircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of prece den ce. In the event of a conflict between the text of this drawing and the referenc es cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in ac cordance with MIL-PRF-38535. Thi s QML flow as documented in the Quality Management (QM) pl an
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifica tion s sha ll not affec t the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specifi ed
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performan ce ch aract eris tic s. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups spec ified in table II. The elec trical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certifi cation mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87578
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test Symbol Conditions
-55°C ≤ TA ≤ +125°C
±VS = ±15 V
Group A
subgroups
Device
type
Limits 1/ Unit
unless otherw ise speci fied
Min
Max
Input offset volt age VOS 2/ 4 01 25 µV
2,3 60
4 02 60
2,3 160
Long term input offset
voltage stability VOS /
time
3/ 4/ 1,2,3 All 1.0 µV/Mo
Average input offset drift V
OS
/ 4/ 1,2,3 01 0.6 µV/°C
temp 02 1.0
Input offs et current I
OS
1 01 30 nA
2,3 50
1 02 50
2,3 85
Input bias current I
IB
1 01 -35 +35 nA
2,3 -60 +60
1 02 -55 +55
2,3 -95 +95
Power dissipation PD 1 01 120 mW
2,3 150
1 02 140
2,3 170
Input voltage range VIN 4/ 1 All -11 +11 V
2,3 -10.3 +10.3
Maximum output voltage
swing
VOUT RL ≥ 2 kΩ 1,2,3 01 -12.5 +12.5 V
02 -12.0 +12.0
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87578
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test Symbol Conditions
-55°C ≤ TA ≤ +125°C
±VS = ±15 V
Group A
subgroups
Device
type
Limits 1/ Unit
unless otherw ise speci fied
Min
Max
Common mode rejection
ratio
CMRR VCM = ±11 V 1 01 117 dB
02 110
VCM = ±10.3 V 2,3 01 112
02 104
Power supply rejection
ratio
PSRR VS = ±4.5 V to ±18 V 1,2,3 01 104 dB
02 100
Input noise voltage eN 0.1 Hz to 10 Hz, 4/
TA = +25
°
C
7 All 0.13 µVPP
Input noise voltage density eND fO = 10 Hz, 4/
T
A
= +25°C
7 All 4.5 nV /
Hz
Input noise curre nt dens ity IND fO = 10 Hz, 4/
T
A
= +25°C
7 All 4.0 pA /
Hz
Slew rate SR RL = 2 kΩ, AVCL ≥ 1,
T
A
= +25°C
7 All 1.7 V/µs
Gain bandwidth products GBWP fO = 100 kHz, 4/
T
A
= +25°C
7 All 5.0 MHz
Open loop output
resistance ZO VO = 0 V, IO = 0 mA, 4/
T
A
= +25°C
7 2000 Ω
Large signal voltage gain A
VOL
V
OUT
= ±10 V, R
L
≥ 1 kΩ 4,5,6 01 2.0 V/µV
02 1.5
1/ The algebraic convention, whereby the m ost negative value is a minimum and the most positive is a maximum ,
is use d in this table. Negative curren t shall be defined as con v entiona l curr ent flow out of a device termina l.
2/ Input offset voltage m easurements are performed by automatic test equipment approximately 0.5 second after
application of power.
3/ Long term input offset stability refers to the average trend line of offset voltage vs. time over extended periods after
the first 30 days of operations. Excluding the first hour of operation, changes in VOS during the first 30 days are
typically 2.5 µV.
4/ If not tested, s hall be guaranteed to the limits specified in table I herein.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87578
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 6
DSCC FORM 2234
APR 97
Device types 01 and 02
Case outlines G and P 2
Terminal
number
Terminal symbo l
1 VOS TRIM NC
2 -INPUT VOS TRIM
3 +INPUT NC
4 -VS NC
5 NC -INPUT
6 OUTPUT NC
7 +VS +INPUT
8 VOS TRIM NC
9 --- NC
10 --- -VS
11 --- NC
12 --- NC
13 --- NC
14 --- NC
15 --- OUTPUT
16 --- NC
17 --- +VS
18 --- NC
19 --- NC
20 --- VOS TRIM
NC = No connection
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87578
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 7
DSCC FORM 2234
APR 97
3.6 Certif i cate of compli an ce. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved sour ce of supply in M IL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requireme nts of M IL-PRF-38535, appendix A and the requirements herein.
3.7 Certif i cate of conform anc e . A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcir cui ts d eliv ered to this draw ing.
3.8 Notific ation of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verific ation and review. DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the
option to review the manufacturer's facility and appli cable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
4. VERIFICATION
4.1 Sampling an d inspection . Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon reques t. The test circuit shall specify
the inputs, outputs, bi ases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Gro up A inspe ctio n.
a. Tests shall be as specified in table II herein.
b. Subgroups 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
4.3.2 Groups C and D inspections.
a. End-point electrical para meter s shall be as specified in table I I herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2) TA = +125°C, m inimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87578
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
D SHEET 8
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004)
---
Final electrical test parameters
(method 5004)
1*,2,3,4,5,6
Group A test requirements
(method 5005)
1,2,3,4,5,6,7
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in a ccor dance with M IL-PRF-38535, appendix A.
6. NOTES
6.1 Inten ded use. Microcirc uits conforming to this drawing are intended for use for Government microcircuit applications
(original equ ipm ent), des ign applicat ion s, and logi sti cs purpo ses.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be c oordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of user s. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this
list will be used for coordination and distribution of changes to the drawings. Users of drawings covering mic roelectronics
devices (FSC 5962) sho uld co ntact DLA Land and Maritime -VA, telephone (614) 692-0547.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 43218-
3990, or telephone (614) 692-0540.
6.6 Approv ed sour ce s of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in M IL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by
DLA Land and Maritime -VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 10-10-20
Approved sources of supply for SMD 5962-87578 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawi ng
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8757801GA 60264 MTLT1007AQH
3/ LT1007AMH/883B
3/ LT1007AMLB
5962-8757801GC 3/ MTL1007AMH/883
5962-8757801PA 60264 MTLT1007AQD8
3/ MTL1007AMJ8/883
3/ LT1007AMJGB
3/ LT1007AMJ8/883B
5962-8757801PC 3/ MTL1007AMD8/883
3/ MTL1007AMJ8/883
5962-87578012A 60264 MTLT1007AQLS
3/ LT1007AMFKB
5962-87578012C 3/ MTL1007AM2/883
5962-8757802GA 60264 MTLT1007QH
3/ LT1007MH
5962-8757802GC 3/ MTL1007MH/883
5962-8757802PA 60264 MTLT1007QD8
3/ MTL1007MJ8/883
3/ LT1007MJGB
3/ LT1007MJ8
5962-8757802PC 3/ MTL1007MD8/883
3/ MTL1007MJ8/883
1 of 2
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued
Standard
microcircuit drawi ng
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-87578022A 60264 MTLT1007QLS
3/ LT1007MFKB
5962-87578022C 3/ MTL1007AM2/883
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufac turer lis ted f o r that part. If the
desired lead finish is not listed contact the vendor
to determine its availa bil it y .
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the perf orma nce requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE Vendor name
number and address
60264 Minco Technology Labs, Inc.
1805 Rutherford Lane
Austin, TX 78754-5101
The information contained herein is disseminated for conveni ence only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
2 of 2
