WIZFI250-EVB - Wiznet Technology

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 1/8

Home | Forum | WIZnet | Museum | Academy(kr)

Document Wiki

Warning: DOMDocument::loadHTML(): htmlParseStartTag: misplaced tag in Entity, line: 26 in

/home/hosting_users/wizwiki/www/wiki/lib/plugins/markdownextra/syntax.php on line 125 Warning:

DOMDocument::loadHTML(): Unexpected end tag : pre in Entity, line: 27 in

/home/hosting_users/wizwiki/www/wiki/lib/plugins/markdownextra/syntax.php on line 125

WizFi250 Quick Start Guide

WizFi250 Evaluation Board

The WizFi250 EVB is the evaluation board for testing WizFi250 and prototyping development. WizFi250 EVB is composed of a

WizFi250 evaluation board and a WizFi250 module.

Feature Identification

Button Description

WizFi250 Reset Through this button, user can restart WizFi250 module.

Function Through the function button, user can enter specific mode without AT Command.

♦ Factory Recovery : When doing Boot or Reset, press the button over 3.5 seconds

♦ AP Mode : When module is working, press it once.

♦ OTA Mode : When module is working, press it twice.

♦ Factory Default : When module is working, press it three times.

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 2/8

Arduino Board Reset With this button, user can restart Arduino board.

LED Description

UART RX/TX Indicate UART RX/TX Status

Power LED Indicate Power On/Off of WizFi250

Mode LED Indicate Data/Command Mode

♦ LOW(ON) : Data Mode

♦ HIGH(OFF) : Command Mode

Wi-Fi LED Indicate Wi-Fi Association

♦ LOW(ON) : Wi-Fi is associated

♦ HIGH(OFF) : Wi-Fi is not associated

Pin Description

BOOT Enter boot mode

♦ SHORT : Start in boot mode

♦ OPEN : Start in application mode

5V Power Alternative choice for 5V power supply

GPIO Pin Through this pin, user can use GPIO signal

Interface Description

UART1 Interface Alternative choice for Serial interface.

SPI Interface Through these pins, user can control SPI interface.

USB Interface This provides power supply & Serial interface

Default serial information:

♦ Baud rate : 115200

♦ Data rate : 8

♦ Stop bits : 1

♦ Parity : None

♦ Flow control : None

Interface Board PIN Map

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 3/8

Interface Board Dimension

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 4/8

2013/08/28 15:45 · kaizen

Start Serial to Wi-Fi

This chapter explains how to set WizFi250 in order to exchange data with peer system. This picture shows the environment for

using Serial to Wi-Fi as example. In this example, WizFi250 is set to the TCP server and peer system is set to the TCP client.

And then data is exchanged between WizFi250 and the peer system.

Using Function Button & Web Server Interface

This section explains how to set WizFi250 using web server in order to use serial to Wi-Fi application. (If you Use the function

button, you can launch web server easily.)

Procedure for setting serial to Wi-Fi is explained below.

1. Press the “Function Button” one time in order to run AP mode and launch the web server. If WizFi250 is changed to

AP mode successfully, Wi-Fi LED will be on and you can see WizFi250’s SSID by your PC

Default information of WizFi250 AP Mode

SSID WizFi250_AP_0008DCXXXXXX

Security WPA2 Mixed

Security Key 123456789

IP Address 192.168.12.1

Gateway Address 192.168.12.1

LED results of WIZFI250:

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 5/8

2. Connect to WizFi250’s SSID …by inputting default password (123456789) and WizFi250’s IP address or URL

(wizfi250.wiznet.com) in your web browser. After that input the user id and user password. ( Default ID : admin, Default

Password : admin )

3. If you select “S2W Setting & Scan Network” menu, …the web page will be shown as below.

If WizFi250 is set successfully, it shows the success message … as in the following picture on the right.

If you select <Next_Step> button, you can move to next page.

WizFi250 TCP/IP Settings guide

Modes AP or Station (connect to AP)

Protocol TCP/UDP (Server / Client)

Remote IP Connecting device's IP address

Remote Port Connecting device's Port

Local Port Module's Port

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 6/8

4. Select WizFi250's DHCP Mode.

It includes DHCP or stactic IP setting.

5. Firstly, input the password of …the AP you want to join and click “Join“ button to connect to that AP.

After setting up, you will see “Device Started Web server and access point stopped. See UART for further

information.” message in web browser. It means that WizFi250 will try to connect to the selected AP.

Important note: If you input the wrong password of AP, you need to redo all procedures.

6. WizFi250 will be associated … to the AP you select… and you can use TCP server in WizFi250.

This picture is the serial message when WizFi250 has set successfully.

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 7/8

Using Serial Command

This section explains how to connect to AP by using serial command.

The module start by default in command mode. If the user inputs the AT commands below, WizFi250 will be connected to AP

by DHCP and run as TCP server.

In this example, the settings of AP will be created as below:

( SSID : WizFiDemoAP, Security : WPA2, Key : 12345678 )

AT(SentATcommandwith0x0d(HexofEnterbutton))

[OK](responsemeaningsuccessfulexecution)

AT+WSET=0,WizFiDemoAP(ATcommandforsettingWiFiassociation)

[OK]

AT+WSEC=0,,12345678(ATcommandforsettingWiFisecurity)

[OK]

AT+WNET=1(ATcommandforsettingDHCP)

[OK]

AT+WJOIN(ATcommandexecutingAPassociation)

Joining:WizFiDemoAP

Successfullyjoined:WizFiDemoAP

[Link‐UpEvent]

IPAddr:192.168.3.104

Gateway:192.168.3.1

[OK]

AT+SCON=SO,TSN,,,5000,1(ATcommandforsettingTCPServer)

[OK]

[CONNECT0](WhenTCPconnectionisdone,itshowsthismessage)

Now, the green mode LED is on, and data can be exchanged from Serial I/F to connected client and back. This mode is called

data mode.

To exit this data mode or to enter into command mode again you need to send a single '+++' string without CR or LF (0x0D,

0x0A) - just the three 0x2B = '+' characters.

Exchanging data with a peer system

This section explains how to exchange data between WizFi250 and Peer System.

This example describes the structure of data flow.

201765 products:wizfi250:wizfi250qsg:start[DocumentWiki]

http://wizwiki.net/wiki/doku.php?id=products:wizfi250:wizfi250qsg:start 8/8

After TCP connection is done and if WizFi250 receives serial data, the serial data will be sent to peer system immediately and

Wizfi250 can receive data from peer system.

2013/08/28 16:43 · kaizen

products/wizfi250/wizfi250qsg/start.txt · Last modified: 2015/03/16 10:33 (external edit)