LMC6681,LMC6682,LMC6684 LMC6681 Single/LMC6682 Dual/LMC6684 Quad Low Voltage, Rail-To-Rail Input and Output CMOS Amplifier with Powerdown Literature Number: SNOS722 LMC6681 Single/LMC6682 Dual/LMC6684 Quad Low Voltage, Rail-To-Rail Input and Output CMOS Amplifier with Powerdown General Description Features The LMC6681/2/4 is a high performance operational amplifier which can operate over a wide range of supply voltages, with guaranteed specifications at 1.8V, 2.2V, 3V, 5V, and 10V. The LMC6681/2/4 provides an input common-mode voltage range that exceeds both supplies. The rail-to-rail output swing of the amplifier assures maximum dynamic signal range. This rail-to-rail performance of the amplifier, combined with its high open-loop voltage gain makes it unique among CMOS rail-to-rail amplifiers. The LMC6681/2/4 is an excellent choice for circuits where the common-mode voltage range is a concern. The LMC6681/2/4 has a powerdown mode which can be controlled externally. In this powerdown mode, the supply current decreases from 700 A per amplifier to less than 1 A per amplifier. The LMC6684 has two powerdown options. Each of the powerdown pins disables two amplifiers. The LMC6681/2/4 has been designed specifically to improve system performance in low voltage applications. The amplifier's 80 fA input current, 0.5 mV offset voltage, and 82 dB CMRR maintain accuracy in battery-powered systems. (Typical unless otherwise noted) n Guaranteed Specs at 1.8V, 2.2V, 3V, 5V, 10V n Rail-to-Rail Input Common-Mode Voltage Range n Rail-to-Rail Output Swing (within 10 mV of supply rail, @ VS = 3V and RL = 10 k) n Powerdown Mode IS OFF 1.5 A/Amplifier (Guaranteed at VS = 1.8V, 2.2V, 3V, and 5V) n Ultra Low Input Current 80 fA n High Voltage Gain (VS = 3V, RL = 10 k): 120 dB n Unity Gain Bandwidth 1.2 MHz Applications n n n n n n Battery Operated Circuits Sensor Amplifiers Portable Communication Devices Medical Instrumentation Battery Monitoring Circuits Level Detectors, Sample-and-Hold Circuits Connection Diagrams 8-Pin DIP/SO 14-Pin DIP/SO DS012042-1 Top View DS012042-2 Top View 16-Pin DIP/SO DS012042-3 Top View (c) 1999 National Semiconductor Corporation DS012042 www.national.com LMC6681 Single/LMC6682 Dual/LMC6684 Quad Low Voltage, Rail-To-Rail Input and Output CMOS Amplifier with Powerdown May 1995 Ordering Information Package Temperature Range NSC Transport Industrial, -40C to +85C Drawing Media Rails 8-Pin Molded DIP LMC6681AIN, LMC6681BIN N08E 8-Pin Small Outline LMC6681AIM, LMC6681BIM M08A Rails LMC6681AIMX, LMC6681B1MX M08A Tape and Reel Rails 14-Pin Molded DIP LMC6682AIN, LMC6682BIN N14A 14-Pin Small Outline LMC6682AIM, LMC6682BIM M14A Rails LMC6682AIMX, LMC6682BIMX M14A Tape and Reel Rails 16-Pin Molded DIP LMC6684AIN, LMC6684BIN N16A 16-Pin Small Outline LMC6684AIM, LMC6684BIM M16A Rails LMC6684AIMX, LMC6684BIMX M16A Tape and Reel www.national.com 2 Absolute Maximum Ratings (Note 1) Operating Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Junction Temperature Range LMC6681AI, LMC6681BI LMC6682AI, LMC6682BI LMC6684AI, LMC6684BI Thermal Resistance (JA) N Package, 8-pin Molded DIP M Package, 8-pin Surface Mount N Package, 14-pin Molded DIP M Package, 14-pin Surface Mount N Package, 16-pin Molded DIP M Package, 16-pin Surface Mount ESD Tolerance (Note 2) Differential Input Voltage Voltage at Input/Output Pin Supply Voltage (V+ - V-) Current at Input Pin (Note 11) Current at Output Pin (Note 3) Current at Power Supply Pin Lead Temp. (soldering, 10 sec.) Storage Temperature Range Junction Temperature (Note 4) 2 kV Supply Voltage (V+) +0.3V, (V-) -0.3V 12V 5 mA 30 mA 35 mA 260C -65C to +150C 150C 1.8V VS 10V -40C TJ +85C -40C TJ +85C -40C TJ +85C 108C/W 172C/W 88C/W 126C/W 83C/W 114C/W 3V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 3.0V, V- = 0V, VCM = VO = V+/2, VPD = 0.6V and RL > 1 M. Boldface limits apply at the temperature extremes (Note 16). Symbol VOS TCVOS Parameter Typ (Note 5) Conditions Input Offset Voltage 0.5 Input Offset Voltage LMC6681AI LMC6681BI LMC6682AI LMC6682BI LMC6684AI LMC6684BI Limit Limit (Note 6) (Note 6) Units 1 3 mV 2.5 4.5 max 1.5 V/C Average Drift IB Input Current (Note 12) 0.08 20 20 pA max IOS Input Offset Current (Note 12) 0.04 10 10 pA max RIN Input Resistance CIN Input Capacitance CMRR Common Mode PSRR 3 82 70 Power Supply 1.5V VS 2.5V 82 Rejection Ratio VO = V+/2 = VCM Input Common Mode CMRR > 50 dB 3.23 Voltage Range -0.3 AV VO pF (Note 13) Rejection Ratio VCM Tera >1 Large Signal Voltage Gain Output Swing RL = 600 (Notes 7, 12) RL = 10 k (Notes 7, 12) RL = 600 to V+/2 62 min 65 dB 65 62 min 3.18 3.18 V 3.00 3.00 min -0.18 -0.18 V 0.00 0.00 max 10 10 V/mV 12 12 V/mV 2.87 2.70 2.70 V 2.58 2.58 min 0.05 2.99 0.01 3 65 70 70 2.95 RL = 10 k to V+/2 dB 1000 0.15 RL = 2 k to V+/2 65 0.3 0.3 V 0.42 0.42 max 2.85 2.85 V 2.79 2.79 min 0.15 0.15 V 0.21 0.21 max 2.94 2.94 V 2.91 2.91 min 0.04 0.04 V 0.05 0.05 max www.national.com 3V DC Electrical Characteristics (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 3.0V, V- = 0V, VCM = VO = V+/2, VPD = 0.6V and RL > 1 M. Boldface limits apply at the temperature extremes (Note 16). Symbol ISC Parameter Output Short Typ (Note 5) Conditions Sourcing, VO = 0V 20 Circuit Current Sinking, VO = 3V IS ON Supply Current when Powered ON IS OFF Supply Current when Powered OFF www.national.com 12 Single, LMC6681 VCM = 1.5V 0.7 Dual, LMC6682 VCM = 1.5V 1.4 Quad, LMC6684 VCM = 1.5V 2.8 Single, LMC6681 VPD = 2.3V 0.5 Dual, LMC6682 VPD = 2.3V 0.5 Quad, LMC6684 VPD = 2.3V 1.0 4 LMC6681AI LMC6681BI LMC6682AI LMC6682BI LMC6684AI LMC6684BI Limit Limit (Note 6) (Note 6) 9.0 9.0 mA 6.7 6.7 min 6.0 6.0 mA 4.5 4.5 min Units 1.13 1.13 mA 1.36 1.36 max 2.26 2.26 mA 2.75 2.75 max 4.52 4.52 mA 5.42 5.42 max 1.5 1.5 A 2.1 2.1 max 1.5 1.5 A 2.1 2.1 max 3.0. 3.0 A 4.2 4.2 max 1.8V and 2.2V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 1.8V and 2.2V, V- = 0V, VCM = VO = V+/2, VPD = 0.4V ( @ 2.2V), VPD = 0.3V (@ 1.8V) and RL > 1 M. Boldface limits apply at the temperature extremes (Note 16). Symbol VOS TCVOS Parameter Input Offset Voltage Conditions V+ = 1.8V, VCM = 1.5V V+ = 2.2V, VCM = 1.5V LMC6681AI LMC6681BI Typ LMC6682AI LMC6682BI (Note 5) LMC6684AI LMC6684BI Limit Limit Units (Note 6) (Note 6) 0.5 3 10 0.5 2 6 mV 3.8 7.8 max mV max V+ = 2.2V 1.5 0.08 20 20 pA max 0.04 10 10 pA max 82 60 60 dB min Rejection Ratio V+ = 2.2V (Note 12) V+ = 2.2V (Note 12) V+ = 2.2V (Note 13) V+ = 1.8V (Note 13) 82 50 50 dB min Power Supply 1.1V VS 5V, 82 70 65 dB Rejection Ratio VO = V+/2 = VCM V+ = 2.2V CMRR > 40 dB 65 62 min 2.38 2.2 2.2 V min -0.15 0.0 0.0 V max V+ = 1.8V CMRR > 40 dB 1.98 1.8 1.8 V min -0.10 0.0 0.0 V max Input Offset Voltage V/C Average Drift IB Input Current IOS Input Offset Current CMRR Common Mode PSRR VCM Input Common Mode Voltage Range VO Output Swing V+ = 2.2V RL = 2 k to V+/2 2.15 0.05 V+ = 1.8V RL = 2 k to V+/2 1.75 0.05 IS ON Supply Current when Powered ON IS OFF Supply Current when Powered OFF Single, LMC6681 VCM = 1.5V 0.7 Dual, LMC6682 VCM = 1.5V 1.4 Quad, LMC6684 VCM = 1.5V 2.8 Single, LMC6681 VPD = 1.5V 0.5 Dual, LMC6682 VPD = 1.5V 0.5 Quad, LMC6684 VPD = 1.5V 1.0 5 2.0 2.0 V 1.88 1.88 min 0.2 0.2 V 0.32 0.32 max 1.6 1.6 V 1.44 1.44 min 0.2 0.2 V 0.32 0.32 max 1.1 1.1 mA 1.32 1.32 max 2.2 2.2 mA 2.7 2.7 max 4.4 4.4 mA 5.3 5.3 max 1.5 1.5 A 2.7 2.7 max 1.5 1.5 A 2.7 2.7 max 3.0 3.0 A 5.4 5.4 max www.national.com 5V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 5.0V, V- = 0V, VCM = VO = V+/2, VPD = 0.9V and RL > 1 M. Boldface limits apply at the temperature extremes (Note 16). Symbol VOS TCVOS Parameter Input Offset Voltage Typ (Note 5) Conditions VCM = 1.5V 0.5 Input Offset Voltage LMC6681AI LMC6681BI LMC6682AI LMC6682BI LMC6684AI LMC6684BI Limit Limit (Note 6) (Note 6) Units 1 3 mV 2.5 4.5 max 1.5 V/C Average Drift IB Input Current (Note 12) 0.08 20 20 pA max IOS Input Offset Current (Note 12) 0.04 10 10 pA max RIN Input Resistance CIN Input Capacitance CMRR Common Mode 3 VCM 82 70 Power Supply Rejection 1.5V VS 2.5V 82 Ratio VO = V+/2 = VCM 65 Input Common Mode CMRR > 50 dB 5.3 Voltage Range -0.3 VO Output Swing RL = 2 k to V+/2 4.9 0.05 IS ON Supply Current when Powered ON IS OFF Supply Current when Powered OFF www.national.com pF (Note 13) Rejection Ratio PSRR Tera >1 Single, LMC6681 VCM = 1.5V 0.8 Dual, LMC6682 VCM = 1.5V 1.5 Quad, LMC6684 VCM = 1.5V 3.0 Single, LMC6681 VPD = 4.3V 0.5 Dual, LMC6682 VPD = 4.3V 0.5 Quad, LMC6684 VPD = 4.3V 1.0 6 65 dB 65 62 min 70 65 dB 62 min 5.18 5.18 V 5.00 5.00 min -0.18 -0.18 V 0.00 0.00 max 4.85 4.85 V 4.58 4.58 min 0.2 0.2 V 0.28 0.28 max 1.24 1.24 mA 1.49 1.49 max 2.48 2.48 mA 3.00 3.00 max 4.96 4.96 mA 6.00 6.00 max 1.5 1.5 A 2.1 2.1 max 1.5 1.5 A 2.1 2.1 max 3.0 3.0 A 4.2 4.2 max 10V DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 10.0V, V- = 0V, VCM = VO = V+/2, VPD = 1.2V and RL > 1 M. Boldface limits apply at the temperature extremes (Note 16). Symbol VOS TCVOS Parameter Input Offset Voltage Typ (Note 5) Conditions VCM = 1.5V 0.5 Input Offset Voltage LMC6681AI LMC6681BI LMC6682AI LMC6682BI LMC6684AI LMC6684BI Limit Limit (Note 6) (Note 6) 1.5 3.5 mV 3.0 5.0 max 1.5 Units V/C Average Drift IB Input Current (Note 12) 0.08 20 20 pA max IOS Input Offset Current (Note 12) 0.04 10 10 pA max RIN Input Resistance CIN Input Capacitance CMRR Common Mode PSRR 3 82 65 Positive Power Supply 1.1V VS 5V 82 Rejection Ratio VO = V+/2 65 Input Common Mode CMRR > 50 dB 10.30 Voltage Range -0.30 VO Output Swing RL = 2 k to V+/2 9.93 0.08 AV ISC dB 62 62 min 70 65 dB 62 min 10.18 10.18 V 10.00 10.00 min -0.18 -0.18 V 0.00 0.00 max 9.7 9.7 V 9.58 9.58 min 0.3 0.3 V 0.42 0.42 max Large Signal RL = 2 k to V+/2 Sourcing 89 25 25 V/mV (Note 12) Sinking 224 25 25 V/mV Output Short Circuit Sourcing, VO = 0V Current (Note 14) 65 70 (Note 14) Supply Current when Powered ON IS OFF 65 Voltage Gain Sinking, VO = 10V IS ON pF (Note 13) Rejection Ratio VCM Tera >1 Supply Current when Powered OFF Single, LMC6681 VCM = 1.5V 0.9 Dual, LMC6682 VCM = 1.5V 1.6 Quad, LMC6684 VCM = 1.5V 3.2 Single, LMC6681 VPD = 9.3V 0.5 Dual, LMC6682 VPD = 9.3V 0.5 Quad, LMC6684 VPD = 9.3V 1.0 7 30 30 mA 22 22 min 30 30 mA 22 22 min 1.50 1.50 mA 1.8 1.8 max 3.00 3.00 mA 3.6 3.6 max 6.00 6.00 mA 7.2 7.2 max 5 5 A 7 7 max 5 5 A 7 7 max 10 10 A 14 14 max www.national.com Powerdown DC Threshold Characteristics Boldface limits apply at the temperature extremes (Note 16). LMC6681AI, LMC6681BI Symbol Parameter LMC6682AI, LMC6682BI Conditions Min VPD, IL Powerdown Voltage Input Low (Device Powered ON; Amplifier meets all specs in the datasheet tables) V+ = 2.2V V- = 0V V+ = 3V VPD, IH Powerdown Voltage Input High (Device Powered OFF; Refer to DC Electrical Characteristics for IS www.national.com OFF specs) V- = 0V V+ = 3V V- = 0V Max 0.4 V 0.6 V 0.45 0.9 V 0.75 1.2 V 1.05 1.5 V 1.65 2.3 V 2.45 V+ = 5V V- = 0V V+ = 10V 4.45 V- = 0V 9.45 8 Typ 0.25 V- = 0V V+ = 5V V- = 0V V+ = 10V V- = 0V V+ = 2.2V Units LMC6684AI, LMC6684BI 4.3 9.3 V V AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25C, V+ = 3V, V- = 0V, VCM = VO = V+/2, VPD = 0.6V and RL > 1 M. Boldface limits apply at the temperature extremes (Note 16). Symbol tON Parameter Time Delay for Typ (Note 5) Conditions LMC6681AI LMC6681BI LMC6682AI LMC6682BI LMC6684AI LMC6684BI Limit Limit Units (Note 6) (Note 6) (Note 15) 50 200 200 s (Note 15) 0.5 2 2 s (Note 8) 1.2 Device to Power ON tOFF Time Delay for Device to Power OFF SR Slew Rate V+ = 10V, (Note 10) 1.2 0.7 0.7 0.55 0.55 0.7 0.7 0.55 0.55 V/s min GBW Gain-Bandwidth Product 1.2 MHz m Phase Margin 50 Deg Gm Gain Margin 12 dB 130 dB Input-Referred V+ = 10V (Note 9) f = 1 kHz Voltage Noise VCM = 0.5V Input-Referred f = 1 kHz 0.5 f = 1 kHz, AV = +1 RL = 10 k, VO = 2 VPP 0.01 Amp-to-Amp Isolation en in 32 Current Noise T.H.D. Total Harmonic Distortion % Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the electrical characteristics. Note 2: Human body model, 1.5 k in series with 100 pF. Note 3: Applies to both single-supply and split-supply operation. Continous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Output current in excess of 30 mA over long term may adversely affect reliability. Note 4: The maximum power dissipation is a function of TJ (max), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max) - TA)/JA. All numbers apply for packages soldered directly into a PC board. Note 5: Typical Values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: V+ = 3V, VCM = 0.5V. For sourcing and sinking, 0.5V VO 2.5V. Note 8: V+ = 3V. Connected as Voltage Follower with 2V step input, and the output is measured from 15%-85%. Number specified is the slower of the positive or negative slew rates. Note 9: Input referred, V+ = 10V, and RL = 100 k connected to 5V. Each amp excited in turn with 1 kHz to produce VO = 2 VPP. Note 10: V+ = 10V. Connected as voltage follower with 8V step Input, and output is measured from 15%-85%. Number specified is the slower of the positive or negative slew rates. Note 11: Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings. Note 12: Guaranteed limits are dictated by tester limitations and not device performance. Actual performance is reflected in the typical value. Note 13: CMRR+ and CMRR- are tested, and the number indicated is the lower of the two values. For CMRR+, V+/2 < VCM < V+ for 1.8V, 2.2V, 3V, 5V, and 10V. For CMRR-, 0 < VCM < V+/2 for 3V, 5V and 10V. For 1.8V and 2.2V, 0.25 < VCM < V+ - 0.3. Note 14: V+ = 10V, VCM = 0.5V. For Sourcing tests, 1V VO 5V. For Sinking tests, 5V VO 9V. Note 15: The propogation delays are measured using an input waveform of f = 5 Hz, and magnitude of 2.4V. Refer to Section 6.3 and Figures 14, 15 for a detailed explanation. Note 16: The VPD (threshold low and threshold high) limits are guaranteed at room temperature and at temperature extremes. Room temperature limits are production tested. Limits at temperature extremes are guaranteed via correlation using temperature regression analysis methods. Refer to Section 6.2 for an overview of the threshold voltages. 9 www.national.com Typical Performance Characteristics Supply Current per Amplifier vs Supply Voltage VS+ = 3V, Single Supply, TA = 25C unless otherwise specified Sourcing Current vs Output Voltage DS012042-40 Sinking Current vs Output Voltage DS012042-41 VOS vs VCM VOS vs VCM Input Voltage Noise vs Common-Mode Voltage DS012042-42 DS012042-44 DS012042-45 DS012042-43 Frequency Response vs Temperature Frequency Response vs RL DS012042-46 www.national.com Input Voltage Noise vs Frequency DS012042-47 10 DS012042-48 Typical Performance Characteristics VS+ = 3V, Single Supply, TA = 25C unless otherwise specified (Continued) CMRR vs Frequency Positive PSRR vs Frequency Negative PSRR vs Frequency DS012042-49 Crosstalk Rejection vs Frequency DS012042-50 Slew Rate vs Supply Voltage DS012042-51 Non-Inverting Large Signal Pulse Response DS012042-54 DS012042-52 Inverting Large Signal Pulse Response DS012042-53 Non-Inverting Small Signal Pulse Response DS012042-55 Inverting Small Signal Pulse Response DS012042-56 11 DS012042-57 www.national.com Typical Performance Characteristics VS+ = 3V, Single Supply, TA = 25C unless otherwise specified (Continued) Stability vs Capacitive Load Stability vs Capacitive Load Stability vs Capacitive Load DS012042-58 DS012042-59 tON Delay till Active-On after tPD OFF in Powerdown Mode, VS = 3V DS012042-39 www.national.com 12 DS012042-60 Application Information 2.0 Rail-to-Rail Output 1.0 Input Common-Mode Voltage Range The approximated output resistance of the LMC6681/2/4 is 50 sourcing, and 50 sinking at VS = 3V. The maximum output swing can be estimated as a function of load using the calculated output resistance. The LMC6681/2/4 has a rail-to-rail input common-mode voltage range. Figure 1 shows an input voltage exceeding both supplies with no resulting phase inversion on the output. 3.0 Low Voltage Operation The LMC6682 operates at supply voltages of 2.2V and 1.8V. These voltages represent the End of Discharge voltages of several popular batteries. The amplifier can operate from 1 Lead-Acid or Lithium Ion battery, or 2NiMH, NiCd, or Carbon-Zinc batteries. Nominal and End of Discharge of Voltage of several batteries are listed below. Battery Type Nominal Voltage End of Discharge Voltage NiMH 1.2V NiCd 1.2V 1V 2V 1.8V Lead-Acid DS012042-5 FIGURE 1. An Input Signal Exceeds the LMC6681/2/4 Power Supply Voltages with No Output Phase Inversion 1V Silver Oxide 1.6V 1.3V Carbon-Zinc 1.5V 1.1V 2.6V-3.6V 1.7V-2.4V Lithium At VS = 2.2V, the LMC6681/2/4 has a rail-to-rail input common-mode voltage range. Figure 4 shows an input voltage extending to both supplies and the resulting output. The absolute maximum input voltage at V+ = 3V is 300 mV beyond either supply rail at room temperature. Voltages greatly exceeding this absolute maximum rating, as in Figure 2, can cause excessive current to flow in or out of the input pins, possibly affecting reliability. The input current can be externally limited to 5 mA, with an input resistor, as shown in Figure 3. DS012042-8 FIGURE 4. The Input Common-Mode Voltage Range Extends to Both Supplies at VS = 2.2V The amplifier is operational at VS = 1.8V, with guaranteed input common-mode voltage range, output swing, and CMRR specs. Figure 5 shows the response of the LMC6681/2/4 at VS = 1.8V. DS012042-6 FIGURE 2. A 7.5V Input Signal Greatly Exceeds the 3V Supply in Figure 3, Causing No Phase Inversion Due to RI DS012042-7 FIGURE 3. Input Current Protection for Voltages Exceeding the Supply Voltage DS012042-9 FIGURE 5. Response of the LMC6681/2/4 at VS = 1.8V 13 www.national.com 3.0 Low Voltage Operation (Continued) Figure 6 shows an input voltage exceeding both supplies with no resulting phase inversion on the output. DS012042-11 FIGURE 7. Resistive Isolation of a 350 pF Capacitive Load Figure 8 displays the pulse response of the LMC6681 circuit in Figure 7. DS012042-10 FIGURE 6. An Input Voltage Signal Exceeds LMC6681/2/4 Power Supply Voltages of VS = 1.8V with No Output Phase Inversion 4.0 Capacitive Load Tolerance The LMC6681/2/4 can typically drive a 100 pF load with VS = 10V at unity gain without oscillating. The unity gain follower is the most sensitive configuration to capacitive load. Direct capacitive loading reduces the phase margin of op-amps. The combination of the op-amp's output impedance and the capacitive load induces phase lag. This results in either an underdamped pulse response or oscillation. Capacitive load compensation can be accomplished using resistive isolation as shown in Figure 7. If there is a resistive component of the load in parallel to the capacitive component, the isolation resistor and the resistive load create a voltage divider at the output. This introduces a DC error at the output. DS012042-12 FIGURE 8. Pulse Response of the LMC6681 Circuit in Figure 7 Another circuit, shown in Figure 9, is also used to indirectly drive capacitive loads. This circuit is an improvement to the circuit shown Figure 7 because it provides DC accuracy as well as AC stability. R1 and C1 serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifiers inverting input, thereby preserving phase margin in the overall feedback loop. The values of R1 and C1 should be experimentally determined by the system designer for the desired pulse response. Increased capacitive drive is possible by increasing the value of the capacitor in the feedback loop. DS012042-13 FIGURE 9. The LMC6682 Compensated to Ensure DC Accuracy and AC Stability www.national.com 14 4.0 Capacitive Load Tolerance (Continued) The pulse response of the circuit shown in Figure 9 is shown in Figure 10. DS012042-14 FIGURE 10. Pulse Response of the LMC6682 Circuit Shown in Figure 9 Application Hints 5.0 Printed-Circuit-Board Layout for High-Impedance Work would cause only 0.05 pA of leakage current. See Figure 12 for typical connections of guard rings for standard op-amp configurations. It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires special layout of the PC board. When one wishes to take advantage of the ultra-low input current of the LMC6681/2/4, typically less than 80 fA, it is essential to have an excellent layout. Fortunately, the techniques of obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC6681/2/4's inputs and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc. connected to the op-amp's inputs, as in Figure 11. To have a significant effect, guard rings should be placed in both the top and bottom of the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012, which is normally considered a very large resistance, could leak 5 pA if the trace were a 5V bus adjacent to the pad of the input. This would cause a 60 times degradation from the LMC6681/2/ 4's actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a resistance of 1011 DS012042-18 FIGURE 11. Example of Guard Ring in PC Board Layout 15 www.national.com 5.0 Printed-Circuit-Board Layout for High-Impedance Work (Continued) DS012042-22 (Input pins are lifted out of PC board and soldered directly to components. All other pins are connected to PC board.) FIGURE 13. Air Wiring DS012042-19 Inverting Amplifier 6.0 Powerdown 6.1 PINOUT FOR THE LMC6681/LMC6682/LMC6684 For the LMC6681/2/4, the input, output, and power pins are the same as those used in the standard configuration. One of the other pins, pin 5 in the case of the LMC6681, is used to enable the powerdown mode. The connection diagrams for the LMC6681/2/4 are on the front page of the datasheet. The LMC6684 has 2 powerdown options. Each of the powerdown pins disables two amplifiers. If both the powerdown pins are pulled high, all four amplifiers will be disabled. Referring to the connection diagrams on the front page of the datasheet, Pin 5 disables amplifiers B and C and Pin 13 disables amplifiers A and D. DS012042-20 Non-Inverting Amplifier 6.2 EXPLANATION OF DATASHEET PARAMETERS The LMC6681/2/4 is ON (meets all the datasheet specs) when the voltage applied to the powerdown pin, VPD is a logic low. The device is OFF when VPD is a logic high. These logic levels are indicated in the test conditions in the datasheet tables. Summarizing these numbers: DS012042-21 Follower FIGURE 12. Typical Connections of Guard Rings The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 13. www.national.com Supply Logic High [V] Logic Low [V] Voltage at room over temp at room over temp 2.2V VPD 1.5 VPD 1.65 VPD 0.4 VPD 0.25 3V VPD 2.3 VPD 2.45 VPD 0.6 VPD 0.45 5V VPD 4.3 VPD 4.45 VPD 0.9 VPD 0.75 10V VPD 9.3 VPD 9.45 VPD 1.2 VPD 1.05 In applications where the powerdown pin is not connected externally, it is pulled to a logic low internally through a current source. The tON and tOFF specs will essentially be the same for a VPD in the specified range. This means that the LMC6681/2/4 will typically be fully operational 50 s after a logic low has been applied to the powerdown pin. Please note that the frequency of VPD in the test circuit below is 5 Hz. 16 6.0 Powerdown powerdown pin is pulled high, the amplifier shuts down, and draws less than 1 A/Amplifier. In this powerdown mode, the output pin has high impedance, and the output of the circuit is pulled to 0V. tON is specified as the time between the 50% points of the trailing edges of the input waveform at the powerdown pin, and the waveform at the output pin. Similarly, the tOFF is specified as the time between the 50% points of the leading edges of the input waveform at the powerdown pin, and the waveform at the output pin. (Continued) 6.3 TEST CIRCUIT TO MEASURE tON AND tOFF The circuit used to measure the tON, and tOFF during the powerdown operation is a voltage follower with a load of 2 k as shown in Figure 14. When the input to the powerdown pin is low, the LMC6681/ 2/4 is on. Since the amplifier is connected in the voltage follower configuation, the output of the circuit is -1V. When the DS012042-16 FIGURE 14. Test Circuit for tON and tOFF Measurements DS012042-17 DS012042-29 (a) tOFF Measurement (b) tON Measurement FIGURE 15. 6.4 tON and tOFF The tON (time delay for device to power on) the tOFF (time delay for device to power off) specs are guaranteed at a supply voltage of 3V. The tON and tOFF spec are independent of the VPD applied in the specified range. Refer to the Powerdown DC Threshold Characteristics table for the values for a logic low and a logic high. The guaranteed spec for tON is 200 s. This does not mean that the signal to the VPD pin can be as high as 5 kHz (1/200 s). Note that the VPD frequency for the tON and tOFF measurements is 5 Hz. The LMC6681/2/4 is ideal for DC type applications where the powerdown pin is controlled by low frequency signals. When the LMC6681/2/4 is powered off, internal bias currents are shutoff. There is a inherent latency in the circuit, and the device has to power off for a certain period of time for the tON spec to apply. Refer to the figure below. tPD OFF refers to the time interval for which the device is in the powerdown mode. Consider the case when the device has been powered off for 5 ms, and then the powerdown pin is pulled to a logic low. From Figure 16, at room temperature, the device powers on after 500 s. DS012042-39 FIGURE 16. tON Delay Till Active-On after tPDOFF in Powerdown Mode, VS = 3V 17 www.national.com 7.0 Compensating for Input Capacitance Applications Transducer Interface Circuits It is quite common to use large values of feedback resistance with amplifiers that have ultra-low input current, like the LMC6681/2/4. Large feedback resistors can react with small values of input capacitance due to transducers, photodiodes, and circuits board parasitics to reduce phase margins. A. PIEZOELECTRIC TRANSDUCERS DS012042-24 FIGURE 18. Transducer Interface Application The LMC6681 can be used for processing of transducer signals as shown in the circuit below. The two 11 M resistors provide a path for the DC currents to ground. Since the resistors are bootstrapped to the output, the AC input resistance of the LMC6681 is much higher. DS012042-15 FIGURE 17. Canceling the Effect of Input Capacitance The effect of input capacitance can be compensated for by adding a feedback capacitor. The feedback capacitor (as in Figure 17), CF, is first estimated by: or DS012042-36 R1CIN R2CF which typically provides significant overcompensation. Printed circuit board stray capacitance may be larger or smaller than that of a breadboard, so the actual optimum value for CF may be different. The values of CF should be checked on the actual circuit. (Refer to the LMC660 quad CMOS amplifier data sheet for a more detailed discussion.) FIGURE 19. LMC6681 Used for Signal Processing An input current of 80 fA and a CMRR of 82 dB causes an insignificant error offset voltage at the output. The rail-to-rail performance of the amplifier also provides the maximum dynamic range for the transducer signals. B. PHOTODIODE AMPLIFIERS 8.0 Spice Macromodel A Spice Macromodel is available for the LMC6681/2/4. The model includes a simulation of: * Input common-mode voltage range * Frequency and transient response * GBW dependence on loading conditions * Quiescent and dynamic supply current * Output swing dependence on loading conditions and many more characteristics as listed on the macromodel disk. Contact the National Semiconductor Customer Response Center at 1-800-272-9959 to obtain an operational amplifier spice macromodel library disk. DS012042-26 FIGURE 20. Photodiode Amplifier Photocells can be used in light measuring instruments. An error offset voltage is produced at the output due to the input current and the offset voltage of the amplifier. The LMC6682, which can be operated off a single battery is an excellent choice for this application with its 80 fA input current and 0.5 mV offset voltage. www.national.com 18 Low Voltage Peak Detector t2 = 0.74 seconds Then, DS012042-23 FIGURE 21. Low Voltage Peak Detector The accuracy of the peak detector is dependent on the leakage currents of the diodes and the capacitors, and the non-idealities of the amplifier. The parameters of the amplifier which can limit the performance of this circuit are (a) Finite slew rate, (b) Input current, and (c) Maximum output current of the amplifier. The input current of the amplifier causes a slow discharge of the capacitor. This phenomenon is called "drooping". The LMC6682 has a typical input current of 80 fA. This would cause the capacitor to droop at a rate of dV/dt = IB/C = 80 fA/100 pF = 0.8 mV/s. Accuracy in the amplitude measurement is also maintained by an offset voltage of 0.5 mV, and an open-loop gain of 120 dB. LMC6681/2/4 as a Comparator DS012042-31 FIGURE 23. Comparator with Hysteresis Oscillators Figure 23 shows the application of the LMC6681/2/4 as a comparator. The hysteresis is determined by the ratio of the two resistors. Since the supply current of the LMC6681/2/4 is less than 1 mA, it can be used as a low power comparator, in applications where the quiescent current is an important parameter. At VS = 3V, typical propagation delays would be on the order of tPHL = 6 s, and tPLH = 5 s. Filters DS012042-30 FIGURE 22. 1 Hz Square -- Wave Oscillator For single supply 5V operation, the output of the circuit will swing from 0V to 5V. The voltage divider set up R2, R3 and R4 will cause the non-inverting input of the LMC6681/2/4 to move from 1.67V (13 of 5V) to 3.33V (23 of 5V). This voltage behaves as the threshold voltage. R1 and C1 determine the time constant for the circuit. The frequency of oscillation, fOSC is DS012042-32 FIGURE 24. Wide-Band Band-Pass Filter The filter shown in Figure 24 is used to process "voice-band" signals. The bandpass filter has a gain of 40 dB. The two corner frequencies, f1 and f2 are calculated as where t is the time the amplifier input takes to move from 1.67V to 3.33V. The calculations are shown below. where = RC = 0.68 seconds t1 = 0.27 seconds. and 19 www.national.com Filters Battery Monitoring Circuit (Continued) The LMC6681/2/4, with its rail-to-rail input common-mode voltage range and high gain (120 dB typical, RL = 10 k) is extremely well suited for such filter applications. The rail-to-rail input range allows for large input signals to be processed without distortion. The high gain means that the circuit can provide filtering and gain in one stage, instead of the typical two stage filter. This implies a reduction in cost, and savings of space and power. This is an illustration of the conceptual use of the LMC6681/ 2/4. The selectivity of the filter can be improved by increasing the order (number of poles) of the design. Sample-and-Hold Circuits DS012042-37 FIGURE 26. Circuit Used to Sense Charging DS012042-34 FIGURE 25. Sample-and-Hold Application When the "Switch" is closed during the Sample Interval, CHOLD charges up to the value of the input signal when the "Switch" is open, CHOLD retains this value as it is buffered by the high input impedance of the LMC6681. Errors in the "hold" voltage are caused by the input current of the amplifier, the leakage current of the CD4066, and the leakage current of the capacitor. While an input current of 80 fA minimizes the accumulation rate for error in this circuit, the LMC6681's CMRR of 82 dB allows excellent accuracy throughout the amplifier's rail-to-rail dynamic capture range. DS012042-38 FIGURE 27. Circuit Used to Sense Discharging The LMC6681/2/4 has been optimized for performance at 3V, and also has guaranteed specs at 1.8V and 2.2V. In portable applications, the RLOAD represents the laptop/ notebook, or any other computer which the battery is powering. A desired output voltage can be achieved by manipulating the ratios of the feedback resistors. During the charging cycle, the current flows out of the battery as shown. While during discharge, the current is in the reverse direction. Since the current can range from a few milliamperes to amperes, the amplifier will have to sense a signal below ground during the discharge cycle. At 3V, the LMC6681/2/4 can accept a signal up to 300 mV below ground. The common-mode voltage range of the LMC6681/2/4, which extends beyond both rails, is thus a very useful feature in this application. A typical offset voltage of 0.5 mV, and CMRR of 82 dB maintain accuracy in the circuit output, while the rail-to-rail output performance allows for a maximum signal range. www.national.com 20 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin Small Outline Package Order Number LMC6681AIM or LMC6681BIM NS Package Number M08A 14-Pin Small Outline Package Order Number LMC6682AIM or LMC6682BIM NS Package Number M14A 21 www.national.com Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16-Pin Small Outline Package Order Number LMC6684AIM or LMC6684BIM NS Package Number M16A 8-Pin Molded Dual-In-Line Package Order Number LMC6681AIN or LMC6681BIN NS Package Number N08E www.national.com 22 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Pin Molded Dual-In-Line Package Order Number LMC6682AIN or LMC6682BIN NS Package Number N14A 16-Pin Molded Dual-In-Line Package Order Number LMC6684AIN or LMC6684BIN NS Package Number N16A 23 www.national.com LMC6681 Single/LMC6682 Dual/LMC6684 Quad Low Voltage, Rail-To-Rail Input and Output CMOS Amplifier with Powerdown Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated