MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 1/21
10 - 1100 mbar absolute pressure range
6 coeffi cients for software compensation
stored on-chip
Piezoresistive silicon micromachined sensor
Integrated miniature pressure sensor 9 x 9 mm
16 Bit ADC
3-wire serial interface
1 system clock line (32.768 kHz)
Low voltage and low power cons u m p tion
DESCRIPTION
The MS5534C is a SMD-hybrid device including a piezoresistive pressure sensor and an ADC-Interface IC. It
provides a 16 Bit data word from a pressure and temperature dependent voltage. Additionally the module
contains 6 readable coefficients for a highly accurate software calibration of the sensor. MS5534C is a low
power, low voltage device with automatic power down (ON/OFF) switching. A 3-wire interface is used for all
communications with a microcontroller.
The MS5 534 C is fully soft war e c ompatible t o t he pr ev ious v ers ions ( MS 553 4A an d M S55 34 B) . C ompared to t he
previous versions the ESD sensitivity level has been improved to 4kV on all pins.
FEATURES APPLICATIONS
Supply voltage 2.2 V to 3.6 V
Mobile altimeter / barometer systems
Low supply current
Weather control systems
-40°C to +125°C operation temperature
Adventure or multi-mode watc hes
No external components required
GPS receivers
BLOCK DIAGRAM
VDD
GND
MCLK
SCLK
DOUT
DIN
ADC
Digital
Interface
Memory
(PROM)
64 bits
SENSOR
SGND
+IN
-IN
dig.
Filter
Sensor
Interface IC
Fig. 1: Block diagram MS5534C
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 2/21
PIN CONFIGURATION
Fig. 2: Pin configuration of MS5534C
Pin Name
Pin
Type
Function
GND
1
G
Ground
SCLK
2
I
Serial data cloc k
DOUT
3
O
Data output
DIN
4
I
Data input
MCLK
5
I
Master clock (32.768 kHz)
VDD
6
P
Positive supply voltage
PEN (1)
7
I
Programming enable
PV (1)
8
N
Negative programming voltage
NOTE
1) Pin 7 (PV) and Pin 8 (PEN) are only used by the manufacturer for calibration purposes and should not be
connected.
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Conditions
Min
Max
Unit
Notes
Supply voltage
VDD
Ta = 25 °C
-0.3
4
V
Storage temperature
TS
-40
+125
°C
1
Overpressure P
MS5534-CP, Ta = 25 °C
5
bar
MS5534-CM, Ta = 25 °C
10
bar
2
NOTES
1) Storage and operation in an environment of dry and non-corrosive gases.
2) The MS553 4-CM is qualifie d referring to the ISO 2281 standard an d can withstan d an absolute press ure of
11 bar in salt water or 100 m water respectively.
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 3/21
RECOMMENDED O PERATING CONDITIONS
(Ta = 25 °C, VDD = 3.0 V unless noted otherwise)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Operating pressure range p 10 1100
mbar
abs.
Supply voltage
VDD
2.2
3.0
3.6
V
Supply current,
average (1)
during conversion (2)
standby (no conversion)
Iavg
Isc
Iss
V
DD
= 3.0 V
4
1
0.1
µA
mA
µA
Current consum ptio n into MCLK
(3)
MCLK = 32.768 kHz 0.5 µA
Operating temperature range
T
-40
+125
°C
Conversion time
tconv
MCLK = 32.768 kHz
35
ms
External clo ck signal (4)
MCLK
30.000
32.768
35.000
kHz
Duty cycle of MCLK
40/60
50/50
60/40
%
Serial data cloc k
SCLK
500
kHz
NOTES
1) Under the assumption of one conversion every second. Conversion means either a pressure or a
temperature measurement started by a command to the serial interface of MS5534C.
2) During conversion the sensor will be switched on and off in order to reduce power consumption; the total on
time within a conversion is about 2 ms.
3) This value can be reduced by switching off MCLK while MS5534C is in standby mode.
4) It is strongly recommended that a crystal oscillator be used because the device is sensitive to clock jitter. A
square-wave form of the clock signal is a must.
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 4/21
ELECTRICAL CHARACTERISTICS
DIGITA L INPUTS
(T = -40 °C .. 125 °C, VDD = 2.2 V .. 3.6 V)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Input High Voltage
VIH
80% VDD
100% VDD
V
Input Low Voltag e
VIL
0% VDD
20% VDD
V
Signal Rise Time
tr
200
ns
Signal Fall Time
tf
200
ns
DIGITAL OUTPUTS
(T = -40 °C .. 125 °C, VDD = 2.2 V .. 3.6 V)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Output High Voltage
V
OH
I
source
= 0.6 mA
80% V
DD
100% V
DD
V
Output Low Voltage
VOL
Isink = 0.6 mA
0% VDD
20% VDD
V
Signal Rise Time
tr
200
ns
Signal Fall Time
tf
200
ns
AD-CONVERTER
(T = -40 °C .. 125 °C, VDD = 2.2 V .. 3.6 V)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Resolution
16
Bit
Linear Range
4'000
40'000
LSB
Conversion Time
MCLK = 32.768 kHz
35
ms
INL
Within linear rang e
-5
+5
LSB
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 5/21
PRESSURE OUTPUT CHARACTERISTICS
With the calibration data stored in the interface IC of the MS5534C, the following characteristics can be
achieved: (VDD = 3.0 V unless noted otherwise)
Parameter
Conditions
Min
Typ
Max
Unit
Notes
Resolution
0.1
mbar
1
Absolute Pressure Accuracy
p =750 .. 1100 mbar
Ta = 25°C
-1.5 +1.5 mbar 2
Relative Pressure Accuracy
p =750 .. 1100 mbar
Ta = 25°C
-0.5 +0.5 mbar 3
Relative Pressure Error over
Temperature
T = -40 .. +85°C
p =300 .. 1000 mbar
-2 +2 mbar 4
T = -40 .. +125°C
p =300 .. 1000 mbar
-8 +5 mbar 4
Long-term Stability
12 months
-1
mbar
5
Maximum Error over Supply
Voltage
V
DD
= 2.2 .. 3.6 V
p = const.
-1.6 1.6 mbar
NOTES
1) A stable pressure reading of the given resolution requires taking the average of 2 to 4 subsequent pressure
values due to noise of the ADC.
2) Maximum error of pressure reading over the pressure range.
3) Maximum error of pressure reading over the pressure range after offset adjustment at one pressure point.
4) With the second-order temperature compensation as described in Section "FUNCTION". See next section
for typical operating curves.
5) The long-term stability is measured with non-sold er ed devic es.
TEMPERATURE OUTPUT CHARACTERISTICS
This temperature information is not required for most applications, but it is necessary to allow for temperature
compensation of the output. (VDD = 3.0 V unless noted otherw ise)
Parameter
Conditions
Min
Typ
Max
Unit
Notes
Resolution
0.005
0.01
0.015
°C
Accuracy
T = 20 °C
-0.8
0.8
°C
T = -40 .. + 85°C
-2
+2
°C
1
T = -40 .. +125°C
-6
+3
°C
1
Maximum Error over Supply
Voltage
VDD = 2.2 .. 3.6 V -0.2 +0.2 °C 2
NOTES
1) With the second-order temperature compensation as described in Section "FUNCTION". See next section
for typical operating curves.
2) At Ta = 25 °C.
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 6/21
TYPICAL PERFORMANCE CURVES
ADC-value D1 vs Pressure (typical)
6000
8000
10000
12000
14000
16000
18000
20000
22000
0100 200 300 400 500 600 700 800 900 1000 1100
Pressure (mbar)
ADC-value D1 (LSB)
-40°C
25°C
125°C
ADC -value D2 vs Temperatu re (typical)
15000
20000
25000
30000
35000
40000
45000
-40 -20 020 40 60 80 100 120
Temperature (°C)
ADC-value D2 (LSB)
Absolute Pressure Accuracy after C alibration, 2nd order compensation
-8
-6
-4
-2
0
2
4
6
8
0100 200 300 400 500 600 700 800 900 1000 1100
Pressure (mbar)
Pressure error (mbar)
125°C
85°C
60°C
25°C
0°C
-40°C
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 7/21
Temperature Error Accuracy vs temperature (typical)
-5
0
5
10
15
-40 -20 020 40 60 80 100 120
Temperature (°C)
Temperature error (°C)
Temperature error (standard
calculation)
Temperature error (with 2nd
order calculation)
Pressure Error Accuracy vs temperature (typical)
-8
-6
-4
-2
0
2
4
6
8
10
12
14
16
18
-40 -20 020 40 60 80 100 120
Temperature (°C)
Pressure error (mbar)
Perror(1000,1st order)
Perror(1000,2nd order)
Perror(800,1st order)
Perror(800,2nd order)
Perror(300,1st order)
Perror(300,2nd order)
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 8/21
Pressure error vs supply voltage (typical)
-1
-0.8
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
2.2 2.4 2.6 2.8 33.2 3.4 3.6
Voltage (V)
Pressure error (mbar)
1000mbar
800mbar
300mbar
Temperature error vs supply voltage (typical)
-0.15
-0.1
-0.05
0
0.05
0.1
0.15
2.2 2.4 2.6 2.8 33.2 3.4 3.6
Voltage (V)
Temperature error (°C)
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 9/21
FUNCTION
GENERAL
The MS5534C consists of a piezo-resistive sensor and a sensor interface IC. The main function of the MS5534C
is to convert the uncompensated analogue output voltage from the piezo-resistive pressure sensor to a 16-bit
digital value, as well as pro vidin g a 16-bit digital value for the temperature of the sensor.
Measured pressure (16-bit) “D1”
Measured temperature (16-bit) “D2”
As the output voltage of a pressure sensor is strongly dependent on temperature and process tolerances, it is
necessar y to compens ate for thes e effect s. This com pensation proce dure m ust be perform ed by softwar e using
an external microcontroller.
For both pressure and temperature measurement the same ADC is used (sigma delta converter):
for the pressure measurement, the differential output voltage from the pressure sensor is converted
for the temperature measurement, the sensor bridge resistor is sensed and converted
During both measurements the sensor will only be switched on for a very short time in order to reduce power
consumption. As both, the bridge bias and the reference voltage for the ADC are derived from VDD, the digital
output data is independent of the supply voltage.
FACTORY CALIBRATION
Every m odule is indi viduall y factor y calibrated at t wo t em peratures and two press ures. As a result, 6 coefficients
necessar y to com pens ate for proces s var iations and t em perature var iat ions ar e calc ulate d and stor ed in the 64-
bit PROM of each module. These 64-bit (partitioned into four words of 16-bit) must be read by the
microcontroller software and used in the program converting D1 and D2 into compensated pressure and
temperature values.
PRESSURE AND TEMPERATURE MEASUREMENT
The sequence of reading pressure and temperature as well as of performing the software compensation is
depicted in Fig. 3 and Fig. 5.
First Word1 to Word4 have to be read through the serial interface. This can be done once after reset of the
microcontroller that interfaces to the MS5534C. Next, the compensation coefficients C1 to C6 are extracted
using bit-wise logical- and shift-operations (refer to Fig. 4 for the bit-pattern of Word1 to Word4).
For the pressure measurement, the microcontroller has to read the 16-bit values for pressure (D1) and
temper ature (D2) via the ser ial interface in a loo p (for instance ev ery second). T hen, the c ompensated pr essur e
is calculated out of D1, D2 and C1 to C6 according to the algorithm in Fig. 3 (possibly using quadratic
temperature compensation according to Fig. 5). All calculations can be performed with signed 16-bit variables.
Results of m ultiplicat ions m ay be u p to 32-b it lon g (+si gn). In the f low accor ding to F ig. 3 a divis ion f ollows e ach
Sensor
D1
D2
Word 1..4
Calculation
in external
micro-
controller
Pressure
Temperature
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 10/21
multiplication. This division can be performed by bit-wise shifting (divisors are to the power of 2). It is ensured
that the results of these divisions are less than 65536 (16 bit).
For the timing of signals to read out Word1 to Word4, D1, and D2 please refer to the paragraph “Serial
Interface".
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 11/21
System
initialisation
Pressure and temperature measurement
Example:
Word1, Word2, Word3 and Word4 (4x16 Bit)
D1 = 17000
D2 = 22500
Start
Convert calibration data into coefficients:
(see bit pattern of Word1-Word4)
Read calibration data (factory calibrated) from
PROM of MS5534C
Read digital pressure value from MS5534C
D1 (16 Bit)
Read digital temperature value from MS5534C
Display pressure and temperature value
Basic equations:
Calculate calibration temper ature
UT1 = 8*C5+20224
Calculate tem perat ur e co mpensated pressure
Difference between actual temperature and reference
temperature:
dT = D2 - UT1
Actual tem pe ra tur e:
TEMP = 200 + dT*(C6+50)/2
10
(0.1°C resolution)
Calculate act ual tem perat ur e
D2 (16 Bit)
SENST1
OFFT1
TCS
TCO
T
ref
TEMPSENS
C1: Pressure sensitivity (15 Bit)
C2: Pressure offset (12 Bit)
C3: Temperature coefficient of pressure sensitivity (10 Bit)
C4: Temperature coefficient of pressure offset (10 Bit)
C5: Reference temperature (11 Bit)
C6: Temperature coefficient of the temperature (6 Bit)
(
Refer to application no te AN517 for limits of coefficients and
calculated results)
Word1 = 50426
Word2 = 9504
Word3 = 48029
Word4 = 55028
C1 = 25213
C2 = 1908
C3 = 859
C4 = 750
C5 = 148
C6 = 32
dT(D2) = D2 - T
ref
TEMP(D2) = 20°+dT(D2)*TEMPSENS
Offset at actual temperature:
OFF = C2*4 + ((C4-512)*dT)/2
12
Sensitivity at actual temperature:
SENS = C1 + (C3*dT)/2
10
+ 24576
X = (SENS * (D1-7168))/2
14
- OFF
Temperature compensated pressure:
P = X*10/2
5
+ 250*10 (0.1mbar resolution)
OFF(D2) = OFFT1+TCO*dT(D2)
SENS(D2) = SENST1+TCS*dT(D2)
P(D1,D2) = D1*SENS(D2)-OFF(D2)
dT = 1092
TEMP = 287
= 28.7 °C
OFF = 7695
SENS = 50705
X = 22732
P = 9603
= 960.3 mbar
Fig. 3: Flow chart for pressure and temperature reading and software compensation
NOTES
1) Readings of D2 can be done less frequently, but the display will be less stable in this case.
2) For a stable display of 1 mbar resolution, it is recommended to display the average of 8 subsequent
pressure values.
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 12/21
C1 (15 Bit)
C5/I
1 Bit
Word1 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB10
C5/II (10 Bit)
C6 (6 Bit)
Word2 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB5 DB4 DB3 DB2 DB1 DB0
C4 (10 Bit)
C2/I (6 Bit)
Word3 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB11 DB10 DB9 DB8 DB7 DB6
C3 (10 Bit)
C2/II (6-Bit)
Word4 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB5 DB4 DB3 DB2 DB1 DB0
Fig. 4: Arrangement (Bit-pattern) of calibration dat a in Word1 to Word4
SECOND-ORDER TEMPERATURE COMPENSATION
In order to obtain full temperature accuracy over the whole temperature range, it is recommended to
compens ate f or the n on-l inear ity of the output of the temperatur e s ensor . This can be ac hi eved by corr ecti ng t he
calculated temperature and pressure by a second order correction factor. The second-order factors are
calculated as follows:
No correction
T2 = 0
P2 = 0
High Temperatures
T2 = 3*(C6+24)*(450 - TEMP)*(450 – TEMP) / 2
20
P2 = T2 * (P - 10000)/2
13
TEMP < 200
yes
Calculate pressure and temperature
TEMP = TEMP – T2
P = P – P2
Low Temperatures
T2 = 11*(C6+24)*(200 - TEMP)*(200 – TEMP) / 2
20
P2 = 3 *T2 * (P - 3500)/2
14
TEMP > 450
yes
200 TEMP 450
yes
Fig. 5: Flow chart for calculating the temperature and pressure to the optimum accuracy.
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 13/21
SERIAL INTERFACE
The MS5534C communicates with microprocessors and other digital systems via a 3-wire synchronous serial
interface as shown in Fig. 1. The SCLK (Serial clock) signal initiates the communication and synchronizes the
data trans fer with each bit bei ng sampled b y the MS5534C on the r ising edge of SCLK and each bit be ing sent
by the MS5534C on the rising edge of SCLK. The data should thus be sampled by the microcontroller on the
falling edg e of SCLK and s ent to the MS5534C with th e fallin g edge of SCL K. The SCLK -signa l is g enerated by
the microprocessor’s system. The digital data provided by the MS5534C on the DOUT pin is either the
conversion result or the software calibration data. In addition, the signal DOUT (Data out) is also used to
indicate t he conversi on status (conversion-r eady signa l, see belo w). The selec tion of the output data is done by
sending the corresponding instruction on the pin DIN (Data input).
Following is a list of possible output data instructions:
Conversion start for pressure measurement and ADC-data-out “D1” (Figure 6a)
Conversion start for temperature measurement and ADC-data-out “D2” (Figure 6b)
Calibration data read-out sequence for Word1 (Figure 6c)
Calibration data read-out sequence for Word2 (Figure 6d)
Calibration data read-out sequence for Word3 (Figure 6c)
Calibration data read-out sequence for Word4 (Figure 6d)
RESET sequence (Figure 6e)
Every communication starts with an instruction sequence at pin DIN. Fig. 6 shows the timing diagrams for the
MS5534C. The device does not need a ‘Chip select’ signal. Instead there is a START sequence (3-Bit high)
before each SETUP sequence and STOP sequence (3-Bit low) after each SETUP sequence. The SETUP
sequence consists in 4-Bit that select a reading of pressure, temperature or calibration data. In case of
pressure- (D 1) or temperat ur e- (D2) r ead in g th e module acknowledges t he s t ar t o f a c onvers i on by a lo w to h igh
transition at pin DOUT.
Two additional clocks at SCLK are required after the acknowledge signal. Then SCLK is to be held low by the
microcontroller until a high to low transition on DOUT indicates the end of the conversion.
This signal can be used to create an interrupt in t he microcontroller. The microcontroller may now read out the
16 bit word b y giving a not h er 17 cloc ks on the SLCK p in. It is poss ib le to int err up t the dat a RE ADO UT sequenc e
with a hol d of the SCLK s ignal. It is important to always read out the last conversion result before starting
a new conversion.
The RESET sequence is special as the module in any state recognizes its unique pattern. By consequence, it
can be used to restart if synchronization between the microcontroller and the MS5534C has been lost. This
sequence is 21-bit long. T he DOUT signal m ight change duri ng that seq uence (s ee Fig. 6e). It is rec ommended
to send the RESET sequence before each CONVERSION sequence to avoid hanging up the protocol
permanently in case of electrical interference.
sequence: START+P-measurement
SCLKDOUTDIN
Bit7
Conversion start for pressure measurement and ADC-data-out "D1":
end of conver sion
Bit6Bit5Bit4Bit3Bit2Bit1Bit0
conversion
(33ms)
DB7
ADC-data ou t MSB ADC-dat a out LSB
Bit8 Bit9
Start-bit Stop-bit
DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
start of conversion
Setup-bits
Fig. 6a: D1 ACQUISITION sequence
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 14/21
sequence: START+T-measurement
SCLK
DOUT
DIN
Bit7
Conversion start for temperature measurement and ADC-data-out "D2":
end of conver sion
Bit6Bit5Bit4Bit3Bit2Bit1Bit0
conversion
(33ms)
Bit8 Bit9
Start-bit Stop-bitSetup-bits
start of conversion
DB7
ADC-data ou t MSB ADC-dat a out LSB
DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
Fig. 6b: D2 ACQUISITION sequence
sequence: coefficient read + addr ess
SCLKDOUTDIN
Bit7
Calibration data read out sequence for word 1/ word 3:
Bit6Bit5Bit4Bit3Bit2Bit1Bit0
DB7
coefficient-data out MSB co efficient-data o ut LSB
Bit8 Bit9
Start-bit Stop-bit
DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
Bit10 Bit11
address word 1
address word 3
Setup-bits
Fig. 6c: Word1, Word3 READING sequence
address word 2
address word 4
sequence: coefficient read + addr ess
SCLK
DOUT
DIN
Bit7
Calibration data read out sequence for word 2/ word 4:
Bit6Bit5Bit4Bit3Bit2Bit1Bit0
DB7
coefficient-data out MSB co efficient-data o ut LSB
Bit8 Bit9
Start-bit Stop-bit
DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
Bit10 Bit11
Setup-bits
Fig. 6d: W2, W4 READ ING seque nce
sequence: RESET
SCLK
DOUT
DIN
Bit7
RESET - sequence:
Bit6Bit5Bit4Bit3Bit2Bit1Bit0 Bit8 Bit9 Bit10 Bit11Bit12 Bit13 Bit14 Bit15 Bit16 Bit17 Bit18 Bit19 Bit20
Fig. 6e: RESET sequence (21 bit)
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 15/21
APPLICATION INFORMATION
GENERAL
The advant age f or t his c om bin ati on of a s ensor with a direc tly adapted int egr at ed c irc uit is to s ave o ther ex ternal
components and to achieve very low power consumption. The main application field for this system includes
portable devices with battery supply, but its high accuracy and resolution make it also suited for industrial and
automot ive ap pl icati ons . The poss ibil ity to com pens ate the s ensor with s of t ware a l lo ws th e us er to a dap t it t o his
particular application. Communication between the MS5534C and the widely available microcontrollers is
realised over an easy-to-use 3-wire serial interface. Customers may select which microcontroller system to be
used, and ther e are no spe cif ic standard inter face c ells r equired, wh ich m ay be of interes t for spec ially desig ned
4 Bit-microcontroller applications.
CALIBRATION
The MS5534C is factory calibrated. The calibration data is stored inside the 64 bit PROM memory.
SOLDERING
Please refer to the application note AN808 for all soldering issues.
HUMIDITY, WATER PROTECTION
The version MS5534-CM carries a metal protection cap filled with silicone gel for enhanced protection against
humidit y. T he pr o pert ies of this g el ens ur e f unc ti on of the s ens or even when in d irec t wat er c ont ac t. This f eat ure
can be useful for waterproof watches or other applications, where direct water contact cannot be avoided.
Nevertheless the user should avoid drying of hard materials like for example salt particles on the silicone gel
surface. In this case it is better to rinse with clean water afterwards. Special care has to be taken to not
mechanically damage the gel. Damaged gel could lead to air entrapment and consequently to unstable sensor
signal, especially if the damage is close to the sensor surface.
The metal protection cap is fabricated of special anticorrosive stainless steel in order to avoid any corrosive
battery effects inside the final product. The MS5534CM was qualified referring to the ISO Standard 2281 and
can withst and a press ure of 11 bar in salt wat er. The conc entration of the sea w ater used f or the qua lification is
41 g of see salt for 1 litre of DI water.
For under water operat ions as s pecified in I SO Stand ard 2281 i t is impor tant to se al the sensor with a rub ber O -
ring around the metal cap. Any salt water coming to the contact side (ceramic and pads) of the sensor could
lead to permanent damage. Especially for "water-resistant 100 m" watches it is recommended to provide a
stable mechanical pusher from the backside of the sensor. Otherwise the overpressure might push the sensor
backwards and even bend the electronic board on which the sensor is mounted.
LIGHT SENSITIVITY
The MS5 534C is sensiti ve to sunlig ht, especial ly to infrared light s ources. This is due to the str ong photo ef fect
of silicon. As the effect is reversible there will be no damage, but the user has to take care that in the final
product the sensor cannot be exposed to direct light during operation. This can be achieved for instance by
placing mechanical parts with holes in such that light cannot pass.
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 16/21
CONNECTION TO PCB
The package outline of the module allows the use of a flexible PCB to connect it. This can be important for
applications in watches and other special devices, and will also reduce mechanical stress on the device.
For applicat ions subjected to m echanical shock, it is recommended to enhance the mechanical reliability of the
solder junctions by covering the rim or the corners of MS5534C's ceramic substrate with glue or Globtop-like
material.
DECOUPLING CAPACITOR
Particular c ar e must be taken when c o nnec t ing the de vic e to p o wer suppl y. A 4 7 µF tanta lum c apacitor must be
placed as close as possible of the MS5534C's VDD pin. This capacitor will stabilize the power supply during
data convers ion and thus, prov ide the hi ghest pos s ib le acc uracy.
APPLI CATION EXAMPL E: ALTIMETER SYSTEM USING MS5534C
MS5534C is a circ uit that c an be used in con nection with a microcontr oller in diving com puter app licat ions. It is
designed for lo w-voltage s ystem s with a sup pl y voltage of 3V, p articu larl y in batt er y applicat ions. T he MS5534C
is optimised for low current consum ption as the AD-converter clock (MCLK) can use the 32.768 kH z frequenc y
of a standard watch crystal, which is supplied in most portable watch systems.
For applications in altimeter systems MEAS Switzerland can deliver a simple formula to calculate the altitude,
based on a linear interpolation, where the number of interpolation points influences the accuracy of the formula.
4/8bit-Microcontroller
LCD-Display
EEPROM
Keypad
MS5534C
SCLK
DIN
DOUT
MCLK
XTAL1
XTAL2
32.768 kHz
optional
VDD
GND
VDD
GND
3V-Battery
47µF
Tantal
Figure 7: Demonstration of MS5534C in a mobile altimeter
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 17/21
DEVICE PACKAGE OUTLINES
Fig. 8: Device package outlines of MS5534-CP
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 18/21
DEVICE PACKAGE OUTLINES (CONTINUATION)
Fig. 9: Device package outlines of MS5534-CM
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 19/21
RECOMMENDED PAD LAYOUT
Pad layout for bottom side of MS5534C soldered onto printed circuit board.
Fig. 10: Layout for bottom side
Pad layout for top side of MS5534C soldered onto printed circuit board.
Fig. 11: Layout for topside
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 20/21
ASSEMBLY
M ECHANIC AL STR ES S
It is recom mended to av oid m echanic al str es s on the PCB on whic h th e s ens or is mounted. The th ickness of the
PCB should not be below 1.6 mm. A thicker PCB is stiffer creating less stress on the soldering contacts. For
applications where mechanical stress cannot be avoided (for example ultrasound welding of the case or thin
PCB’s in watches) please fix the sensor with drops of low stress epoxy (for example Hysol FP-4401) at the
corners of the sensor as shown below.
MOUNTING
The MS5534C can be placed with automatic Pick&Place equipment using vacuum nozzles. It will not be
damaged by the vacuum. Due to the low stress assembly the sensor does not show pressure hysteresis effects.
Special care has to be taken to not touch the protective gel of the sensor during the assembly.
The MS5534C can be mounted with the cap down or the cap looking upwards. In both cases it is important to
solder al l c o ntact pads. T he P ins P EN and P V s h al l be lef t op en or c on nected to VDD. Do not connect the Pins
PEN and PV to GND!
Placement cap up
SEALING WITH O-RING
In products like outdoor watches the electronics must be protected against direct water or humidity. For those
products the M S5 534-CM pr ovides the p os s ibility to seal with an O -ring . The prote c tive cap of the M S5 534CM is
made of special anticorrosive st ainless steel with a polished surface. In addition to this the MS5534C M is filled
with silico ne gel cover ing the sens or and the b onding wires . The O -ring (or O-rings ) shall be plac ed at the outer
diameter of the metal cap. This method avoids mechanical stress because the sensor can move in vertical
direction.
MS5534C Barometer Module
DA5534C_007 www.meas-spec.com Jun. 27, 2011
0005534C1175 ECN1511 21/21
CLEANING
The MS5534C has been manufactured under cleanroom conditions. Each device has been inspected for the
homogeneity and the cleanness of the silicone gel. It is therefore recommended to assemble the sensor under
class 10’000 or better conditions. Should this not be possible, it is recommended to protect the sensor opening
during ass embl y from entering par ticles and d ust. To avo id cleaning of the PCB, s older paste of type “no-clean”
shall be used. Cleaning might damage the sens o r!
ESD PRECAUTIONS
The electrical contact pads are protected against ESD up to 4 kV HBM (human body model). It is therefore
essentia l to groun d machin es and p ers onal properl y d ur ing ass embl y and han dl in g of the d ev ic e. T he MS 55 34C
is shipped in antistatic transport boxes. Any test adapters or production transport boxes used during the
assembly of the sensor shall be of an equivalent antistatic material.
ORDERING INFORMATION
Product Code
Product
Art. No
Package
Comments
MS5534-CP Barometer Module
with plastic cap 325534008
SMD hybrid with solder paste,
plastic prot ect ion cap Standard version
MS5534-CM Barometer Module
with metal cap 325534009
SMD hybrid with solder paste,
metal protection cap,
silicone gel sensor protection
Recommended for
outdoor products
NORTH AMERICA
EUROPE
ASIA
Measurement Specialties
45738 Northport Loop West
Fremont, CA 94538
Tel: +1 800 767 1888
Fax: +1 510 498 1578
e-mail: pfg.cs.amer chameas-
spec.com
Website: www.meas-spec.com
MEAS Switzerland Sàrl
Ch. Chapons-des-Prés 11
CH-2022 Bevaix
Tel: +41 32 847 9550
Fax: + 41 32 847 9569
e-mail: sales.chameas-spec.com
Website: www.meas-spec.com
Measurement Specialties (China), Ltd.
No. 26 Langshan Road
Shenzhen High-Tech Park (North)
Nanshan District, Shenzhen, 518057
China
Tel: +86 755 3330 5088
Fax: +86 755 3330 5099
e-mail: pfg.cs.asiaameas-spec.com
Website: www.meas-spec.com
The information in this sheet has been carefull y reviewed and is believed to be accurate; however, no responsibilit y is assumed for
inaccuracies. Furtherm ore, this inform ation does not convey to the purchaser of such devices any license under the patent rights to the
manufacturer. Measurem ent Specialt i es, Inc. reserves the right t o make changes without furt her notice to any product herein. Measurement
Specialti es, Inc. makes no warranty, represent ation or guarant ee regarding the sui t abili t y of its product for any particular purpose, nor does
Measurement Specialti es, Inc. assume any liability arising out of the application or use of any product or circuit and specifica lly d is claims
any and all liabilit y, includi ng without limitation consequential or incidental damages. Typical paramet ers can and do vary in different
applicat i ons. All operat i ng parameters must be validated for each customer application by customer’s technic al experts. Meas urem ent
Specialti es, Inc. does not convey any license under its patent rights nor the rights of others.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TE Connectivity:
325534008-50 325534009-50 325534009-00 325535009-50