DEVKIT1207 - EMBEST - Datasheet.Live

DevKit1207 Evaluation Kit

 120MHz STM32F207IGT6 ARM Cortex-M3 32-bit Flash Microcontroller

 CPU Internal 1MBytes of Flash and 128 (system) +4 (backup) KBytes of SRAM

 1 USB2.0 OTG Full-speed Port and 1 USB2.0 OTG High-speed Port

 3.5-inch TFT LCD and 4-wire Resistive Touch Screen

 10/100 Ethernet with IEEE 1588v2, CAN2.0B, IrDA, TF, Audio, JTAG…

 G-sensor 3-Axis Acceleration Sensor

 Optional 1.3 megapixel Digital Camera Module

 Supports for uC/OS-II and FreeRTOS Real-time Operating Systems

Figure 1-1 DevKit1207 Evaluation Board with 3.5” LCD and Touch Screen

Overview

The STMicroelectronics’ STM32F207IGT6 flash microcontroller is among STM32F207xx family,

which is based on the high-performance ARM Cortex-M3 32-bit RISC core operating at a

frequency of up to 120MHz, with high-speed embedded memories (1Mbytes of flash memory and

128Kbytes of system SRAM), 4Kbytes of backup SRAM, and powerful peripheral functions,

including digital camera module interface, High-speed USB OTG, Full-speed USB OTG, Ethernet

MAC, CAN2.0B, multiple timers, ADCs and DACs, I2C, I2S, SPI, UARTs/USARTs, SDIO, LCD

interface, RTC and programmable IOs.

Embest DevKit1207 Evaluation Kit is a complete development platform for STM32F207IGT6

devices which enables engineers to easily and rapidly evaluate, prototype and test designs built

around the STMicroelectronics STM32F207xx series microcontrollers. The DevKit1207 board

has on-board 2Kbits EEPROM and exposed a full range of hardware peripherals to support

HS/FS USB OTG, Ethernet, CAN, Serial port, IrDA, TF card, LCD, Touch screen, Audio,

G-sensor, RTC, JTAG, etc. The kit is provided with an industrial-level 3.5 inch LCD with resistive

touch screen. A digital camera module CAM1207 is also offered as an option to customers.

Embest has ported uC/OS-II and FreeRTOS real-time operating systems on this board and the

software also features the GUI support on uC/OS-II and LwIP_v1.3.2 protocal support on

FreeRTOS. Embest provides the uC/OS-II BSP, FreeRTOS source tree and plenty of software

examples, board schematic and user manual to help customer better understanding this board and

develop your own applications.

Hardware Features

Processor

 STMicroelectronics STM32F207IGT6 Flash Microcontroller

- ARM 32-bit Cortex-M3 CPU with ART accelerator, frequency up to 120MHz

- Onchip 1Mbytes of Flash memory and 128+4Kbytes of SRAM

- Flexible static memory controller that supports Compact Flash, SRAM, PSRAM, Nor

and Nand memories

- LCD parallel interface, 8080/6800 modes

- USB 2.0 HS/FS Device/Host/OTG

- 10/100 Ethernet MAC, supports IEEE 1588v2 hardware, MII/RMII

- 2 CAN 2.0B interfaces, 4 USARTs and 2 UARTs, 2 with muxed I2S, 3 SPI (30Mbit/s)

- 8- to 14-bit parallel camera interface (up to 48Mbytes/s)

- 1-/4-/8-bit SD/MMC/SDIO interface, supports up to 32Gbytes storage

- Up to 140 I/O ports up to 60MHz

- Up to 17 timers (two 32-bit timers), up to 120MHz

- 3 x 12-bit A/D converters, 2 x 12-bit D/A converters

- Analog true random number generator

- Low power, supports Sleep, Stop and Standby modes

- Supports booting from Flash, System memory or SRAM

- Supports ISP and IAP programming

External Memory

 Onboard I2C compatible serial interface 2Kbits EEPROM

 Micro SD card slot

Audio interfaces

 1-channel stereo headphone output jack

 1-channel speaker output jack

 1-channel audio DAC output jack

LCD/Touch Screen

 3.5 inch TFT color LCD (240 x 320-pixel RGB resolution, 262000 colors, 16-bit

8080 parallel interface, brightness control via PWM)

 4-wire resistive touch screen

Data Transfer Interfaces

 1-channel 5-wire RS232 Serial Port

 1 x USB2.0 OTG/Device/Host, High-speed, 480Mbps

 1 x USB2.0 OTG/Device/Host, Full-speed, 12Mbps

 10/100 Ethernet with IEEE 1588v2 (RJ45 connector)

 1 x CAN2.0B interface

 IrDA transceiver

Input Interface and Other Facilities

 1 x Potentiometer (A/D converter)

 2 x USER buttons

 1 x RESET button

 1 x WAKEUP button

 20-pin standard JTAG interface

 RTC battery socket (User needs to prepare battery, CR1220 model is recommended)

 1 x LED for Power indicator

 2 x LEDs for USB OTG FS indicators

 2 x LEDs for USB OTG HS indicators

 4 x User LEDs

 140 GPIO pins are all brought out

Mechanical Parameters

 Dimensions: 160 mm x 115 mm

 Input Voltage: +5V

 Power consumption: 0.4A@5V

 Working Temp.: -10 ℃ ~ 70 ℃

 Humidity Range: 20% ~ 90%

Note: RTC battery is not provided in default deliveries, user needs to prepare it yourself, Type

model CR1220 is recommended. Some functions need to use Jumpers to configure before using.

IrDA

Camera Interface

USB OTG_FS

USB OTG_HS

LCD/Touch Screen

Interface

User Keys

Potentiometer

Power In

Audio Out

CAN

Serial port

Ethernet

JTAG

Interface

TF card slot

G-sensor

Module

Wakeup

Reset

Speaker

RTC battery

STM32F207IGT6

IrDA

Configuration

TF card

Configuration

Bootloader

Configuration

Serial port

Configuration

GPIO pins

Figure 1-2 DevKit1207 Evalution Board

Optional Digital Camera Module CAM1207

The CAM1207 Digital Camera Module is designed specially for using on Embest DevKit1207

products connecting via 30-pin FPC connector. It uses a CMOS image sensor which is a 1.3

megapixel Digital Camera.

CAM1207 Digital Camera Module

CAM1207 connects to DevKit1207 board

Dimension

47.8mm * 37.6mm * 6mm

Signal system

CMOS 1.3 megapixel

Resolution

up to 1280 * 1024

Frame rate

15 fps for SXGA

30 fps for VGA, CIF

Interface

30-pin FPC connector

Power supply

From board

Working Temp.

-10 ~ +70°C

Board Support

DevKit1207

Functions

Supports photo taking

Supports photo saving

Function Block Diagram

STM32F207IGT6

120MHz

USART

COM 5 line

RS232

Audio Out

ADC

LCD

DEBUG

RTC

CAN 2.0B

MAC

1 Channel 12bit

LCD (RGB) and

Touch

SDIO

TF Card

Ethernet

Speaker

DCMI

RTC

EEPROM

Camera

IrDA

USB

USB2.0 OTG_FS

USB2.0 OTG_HS

G-Sensor

DP83848C

CSC2L52

CAN

I2C1

TAJ1040

I2C1

LEDS

I2S2

DAC Out

GPIO

Extented

Interface

LIS33DE

AT24C02

Figure 1-3 DevKit1207 Function Block Diagram

Software

Features

The DevKit1207 Evaluation Kit software mainly features as below:

 Supports for uC/OS-II_v2.86 and FreeRTOS_v6.1.0 real-time operating systems

 Supports UCGUI_v3.90a

 Supports FatFs_vR0.08a file system

 Supports LWIP _v1.3.2 protocol stack

 Provided with plenty of source code

Boot Modes

The DevKit1207 Evaluation Board is able to boot from CPU internal system memory or

embedded SRAm, user needs to configure the boot pins to select the mode. The boot loader is

located in system memory. It is used to reprogram the Flash memory by using Serial port or USB

OTG FS in Device mode through DFU (device firmware upgrade).

Drivers and Software examples

Embest has provided complete drivers and software examples for this kit. User can demonstrate

and test each software example and observe the result from LCD which would be easy to

understand.

The software examples mainly include following parts:

 Examples for Basic peripherals drivers (see Table 1-1 below)

Table 1-1

ADC

ADC3_DMA

Transfer ADC3 converted data to to the memory using

DMA

DualADC_Interleaved_

DMAmode3

Cross access dual-channel ADC converted data using

DMA mode 3

DualADC_RegulSimu_

DMAmode1

Synchronization access dual-channel ADC converted

data using DMA mode 1

TripleADC_Interleaved

_DMAmode2

Cross access three-channel ADC converted data using

DMA mode 2

CAN

LoopBack

CAN loopback testing example

Networking

CAN communication testing example

CRC

CRC_Example

CRC verify testing example

DAC

DAC_SignalsGeneratio

DAC signal generator (can get various wave signals)

testing example

DMA

FLASH_RAM

Transfer data from Flash to RAM using DMA

EXTI

EXTI_Example

Configure external interrupt of EXTI

FLASH

Program

Programming Flash, block erase, read and write

Write_Protection

Write protection on Flash

GPIO

IOToggle

Configure voltage of specified pins via GPIOs

JTAG_Remap

Remap JTAG pins as general IOs

I2C

EEPROM

Read and write on EEPROM using I2C

GSensor-LIS33DE

3-Axis Acceleration Sensor testing example

I2S

Audio

Play audio testing example through I2S

IWDG

IWDG_Example

Single watchdog reset function example

LCD-Touch

STMPE811QTR

LCD and Touch screen application testing example

Lib-DEBUG

Lib_DEBUG_Example

DEBUG testing example

NVIC

DMA_WFIMode

Wakeup system from WFI mode using DMA data

stream interrupt

IRQ_Priority

Set interrupt using interrupt priority

VectorTable_Relocation

Relocate interrupt using interrupt table

PWR

BOR

Power-Off Reset testing example

CurrentConsumption

Current testing example

PVD

Programmable voltage detection testing example

STANDBY

Standby mode testing example

STOP

Stop mode testing example

RCC

RCC_Example

Configure different system clock frequency via RCC

RNG

RNG_MultiRNG

Multi-channel random number generator testing

example

RTC

BKP_Domain

Implement using perpetual calender through

BKP_Domain

HW_Calendar

Implement using RTC Alarm through RTC controller

TimeStamp

Implement time-stamping function through RTC

controller

SDIO

uSDCard

Read and write SD card using FatFs_vR0.08a

SysTick

SysTick_Example

Implement delay through tick interrupt, light up LED

with flick

TIM

6Steps

6-phase PWM output testing example

InputCapture

TIM input capture mode testing example

OCActive

TIM output active mode testing example

OCInactive

TIM output inactive mode testing example

OCToggle

TIM output trigger mode testing example

OnePulse

TIM single pulse mode testing example

Parallel_Synchro

Several TIM parallel and synchronization testing

example

PWM_Input

PWM input mode testing example

PWM_Output

PWM output mode testing example

TIM1_Synchro

TIM1, 3 and 4 parallel and synchronization testing

example

TIM9_OCToggle

TIM9 output trigger mode testing example

TIM10_PWMOutput

Timer 10 PWM output testing example

TimeBase

Timer basic function testing example

USART

USART_IRDA

IrDA transmitting and receiving testing example

USART_Printf

Hyper-terminal input and output testing example

WWDG

WWDG_Example

Watchdog reset testing example

 Example for IrDA driver

 Example for I2S Audio driver

 Application example for G-sensor

 Application example for SD card supporting FatFs_vR0.08a file system

 Application example for USB Host/Device/OTG (see Table 1-2 below)

Table 1-2

USB Device application examples

AUDIO

Use board as audio device, similar to USB acoustics, user can play music on

PC and output sound through board

DFU

Use board as DFU device, user can use it for system firmware updating.

DualCore

Dual-USB channel testing example. Use HS-USB as MSC device and

FS-USB as HID

device.

HID

Use board as HID (Human Interaction Device) to implement USB mouse

operation.

MSC

Use board as MSC (Mass Storage Device) to implement data exchange

between USB Host and board.

VCP

Use board as VCP (Virtual COM Port), user can regard board as a

USB-to-COM module

USB OTG application examples

DRD

DevKit1207 board can be used as either USB Host or USB Device

USB Host application examples

DualCore

Dual-USB channel testing example, use HS-USB as MSC (Mass Storage

Device) host and FS-USB as HID (Human Interaction Device) host.

HID

Use board as HID (Human Interaction Device) host and can recognize

USB mouse and USB keyboard.

MSC

Use board as MSC (Mass Storage Device) and can recognize U disk and

other mobile storage devices.

 Application example for Ethernet on FreeRTOS/Non-OS/LWIP v1.3.2 protocol stack

(see Table 1-3 below)

Table 1-3

Application example for Ethernet on FreeRTOS and LWIP v1.3.2 protocol stack

httpserver_netconn

Webserver application example based on netconn

httpserver_socket

Webserver application example based on socket

udptcp_echo_server_netcon

TCP/UDP Echo application example based on netconn 的

TCP/UDP

Application example for Ethernet on Non-OS and LWIP v1.3.2 protocol stack

httpserver

Webserver application example

tcp_echo_client

Simple Echo application example of Tcp client

tcp_echo_server

Simple Echo application example of Tcp server

tftpserver

Tftpserver application example

udp_echo_client

Simple Echo application example of dup client

udp_echo_server

Simple Echo application example of server

 Application example for OS porting on UCOSII_v2.86 and UCGUI_v3.90a

Function Demonstrations

GUI3.90A Function Demonstration (see Figure 1-1)

Figure 1-1

2-channel USB Host Function Demonstration (see Figure 1-2)

Figure 1-2

Httpserver Network Function Demonstration

1) Input http://192.168.0.163 in browser and you can visit the webpage on DevKit1207.

Figure 1-3

2) Click “LED control” to get into LED control interface, select or cancel LED1, LED2, LED3,

LED4 and press “Send”, the LEDs on board will work relatively.

Figure 1-4

3) Click “ADCstatus bar” to get the voltage of potentiometer on board.

Figure 1-5

Application cases (Remote Control System Solution)

Order Information

Order No.

T6010169

Item

DevKit1207 Evaluation Kit

Deliveries

 One DevKit1207 Evaluation board

 One 3.5 inch LCD with Touch screen

 One 5V Power adapter

 One cross serial cable (DB9 to DB9)

 One cross net cable

 One USB cable (Type A Male to Type Mini-B Male)

 One USB cable (Type A Female to Type Mini-A Male)

 One Product CD (including user manual, schematic in PDF format,

datasheet, uC/OS-II BSP, FreeRTOS source tree, software examples)

Option

 CAM1207 Digital Camera Module

Price

Please contact us.

More information about this product can be found at:

http://www.embedinfo.com/english/Product/devkit1207.asp

http://www.armkits.com/Product/devkit1207.asp

Embest Technology Co., LTD.

Room 509, Luohu Science&Technology Building,

#85 Taining Rd., Shenzhen, Guangdong, China 518020

Tel: +86-755-25635656/25636285

Fax: +86-755-25616057

Email: market@embedinfo.com

http://www.embedinfo.com/english http://www.armkits.com