Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 1
DATA SHEET
SKY66109-11: 2.4 GHz ZigBee®/Smart Energy Front-End
Module
Applications
Smart meters
In-home appliances
Smart thermostats
Features
Integrated PA with up to +22.5 dBm output power
Integrated LNA with programmable bypass
Integrated antenna switching with transmit and receive diversity
function
Low noise figure: 2 dB typical
Differential transmit/receive interface with integrated baluns
Fast switch on/off time: <800 ns
Supply range: 2.0 V to 3.6 V
Sleep mode current: 0.05 μA typical
No bias resistor is required
Small MCM (20-pin, 3 x 4 x 0.9 mm) package, NiPdAu-plated
(MSL3, 240 °C per JEDEC-J-STD-020)
Skyworks Green
TM
products are compliant with
all applicable legislation and are halogen-free.
For additional information, refer to Skyworks
Definition of Green
TM
, document number
SQ04–0074.
203034-002
1
GND
TXP
TXN
V
B_OUT
RXP
RXN
V
B_IN
GND
GND
ANT2
CTX
VCC1
CPS
CSD
VCC2
GND
ANT_SEL
ANT1
GND
2
3
4
5
6
14
15
16
13
12
11
20 19 18 17
89107
GND
Figure 2. SKY66109-11 Pinout
(Top View)
PA
LNA
Balun
RXP
RXN
Logic
control
TXP
TXN ANT1
ANT2
VB_OUT
V
B_IN
CPS
CTX
CSD
ANT_SEL
Balun
203034-001
Figure 1. SKY66109-11 Functional Block Diagram
Description
The SKY66109-11 is a high-performance, fully integrated RF
front-end module (FEM) designed for ZigBee®/Smart Energy
applications.
The SKY66109-11 is designed for ease of use and maximum
flexibility. The device provides integrated and fully matched input
baluns, an integrated interstage matching and harmonic filter, and
digital controls compatible with 1.6 to 3.6 V CMOS levels.
The RF blocks operate over a wide supply voltage range from
2.0 V to 3.6 V that allows the SKY66109-11 to be used in battery
powered applications over a wide spectrum of the battery
discharge curve.
The SKY66109-11 is provided in a small, 20-pin, 3 x 4 mm Multi-
Chip Module (MCM) package. A functional block diagram is
shown in Figure 1. The pin configuration and package are shown
in Figure 2. Signal pin assignments and functional pin
descriptions are provided in Table 1.
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G
Table 1. SKY66109-11 Signal Descriptions
Pin Name Description Pin Name Description
1 GND Ground 11 GND Ground
2 TXP Positive transmit input signal from transceiver, 200
Ω differential 12 ANT1 Connect to 50 Ω antenna
3 TXN Negative transmit input signal from transceiver, 200
Ω differential 13 GND Ground
4 VB_OUT Transmit balun bias core supply from transceiver
(optional connection) 14 ANT_SEL Connect to GPIO signal to control antenna switch (see
Table 7)
5 RXP Positive receiver output signal to transceiver, 200 Ω
differential 15 GND Ground
6 RXN Negative receiver output signal to transceiver, 200
Ω differential 16 VCC2 Connect to positive supply
7 VB_IN Receive balun bias core supply from transceiver
(optional connection) 17 CSD Connect to GPIO signal for mode control (see Table 6)
8 GND Ground 18 CPS Connect to GPIO signal for mode control (see Table 6)
9 GND Ground 19 VCC1 Connect to positive supply
10 ANT2 Connect to 50 Ω antenna 20 CTX Connect to GPIO signal for mode control (see Table 6)
The balun at the FEM PA input (or LNA output) can also be used to inject a bias
operating point for the transceiver output stage (the shunt inductor provides a DC
path on the other side). The inductor also tunes out any parasitic capacitance.
If the SOIC transceiver does not require a DC bias, leave the VB_IN open.
CPS
CSD
CTX
FEM
SoC
VDD_PA VB_OUT
1 pF 1 pF
2n7
1 k
Ω
each series resistor,
placed close to the SKY66109 pins.
Optional Output Filter
203034-003
Differential source
or load impedance symbol
Input
Input
1.8 V V
BIAS_IN
1.8 V
1.8 V Decoupling capacitor
on chip
Internal Lattice Balun
VB_IN
VREG_OUT +1.8 V
Figure 3. Injecting a Bias Operating Point for the Transceiver Output Stage
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 3
Electrical and Mechanical Specifications
The absolute maximum ratings of the SKY66109-11 are provided
in Table 2. The recommended operating conditions are specified
in Table 3 and electrical specifications are provided in Tables 4
and 5.
The state of the SKY66109-11 is determined by the logic provided
in Tables 6 and 7.
Table 2. SKY66109-11 Absolute Maximum Ratings1
Parameter Symbol Minimum Maximum Units
Supply voltage VCC1 –0.3 +3.6 V
Supply voltage VCC2 –0.3 +3.82 V
Control pin voltages –0.3 +3.6 V
Transmit output power at ANT1 or ANT2 port into 50 Ω load POUT_TX_MAX +22.5 dBm
Transmit input power at the TXN and TXP ports PIN_TX_MAX +6 dBm
Receive input power at ANT1 or ANT2 ports, LNA mode PIN_RX_MAX +10 dBm
Receive input power at ANT1 or ANT2 ports, bypass mode PIN_RX_BYPASS_MAX +15 dBm
Operating temperature TA –40 +125 C
Storage temperature TSTG –40 +125 C
Electrostatic discharge:
Human Body Model (HBM), Class 1C
ESD
1000
V
1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set
at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
2 Vcc2 is restricted to +3.6 V when operated at TA = 125 C.
ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This
device must be protected at all times from ESD when handling or transporting. Static charges may easily produce
potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-
standard ESD handling precautions should be used at all times.
Table 3. Recommended Operating Conditions
Parameter Symbol Minimum Typical Maximum Units
Supply voltage for balun bias VB_IN, VB_OUT 1.6 3.6 V
Supply voltage on VCC pins VCC1, VCC2 2.0 3.0 3.6 V
Operating temperature TA –40 +25 +125 C
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G
Table 4. SKY66109-11 Electrical Specifications1
(VCC1 = VCC2 = 3.0 V, TA = +25 C, Unless Otherwise Noted)
Parameter Symbol Test Condition Min Typical Max Units
DC Characteristics
Total supply current ICC_TX POUT = +20 dBm
POUT = +17 dBm2
POUT = +10 dBm2
110
90
45
mA
mA
mA
Total supply current ICC_RX 5 7 mA
Total supply current ICC_RX_BYPASS 300 μA
Sleep supply current ICC_OFF No RF 0.05 1.00 μA
Quiescent current Icq No RF 30 mA
Logic Characteristics
Control voltage:
High
Low
VIH
VIL
1.6
0
3.6
0.3
V
V
Control current:
High
Low
IIH
IIL
1
1
μA
μA
Dual Antenna Switch Characteristics
Isolation between ANT1 and ANT2 ports ISOLANTSW –20 dB
ANT1 to ANT2 switching time tANT1_ANT2 400 ns
1 Performance is guaranteed only under the conditions listed in this table.
2 Not tested in production. Fully characterized and guaranteed by design.
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 5
Table 5. SKY66109-11 Electrical Specifications1
(VB_IN = VB_OUT = 1.6 to 3.6 V, VCC1 = VCC2 = 3.0 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter Symbol Test Condition Min Typical Max Units
AC Transmit Characteristics
Frequency range f 2400 2483 MHz
Output power at ANT1 or ANT2 port POUT VCC1 = VCC2 =:
3.6 V
3.3 V
3.0 V
2.7 V
2.0 V
+22.5
+21.0
+20.5
+20.0
+17.0
dBm
dBm
dBm
dBm
dBm
Small signal gain S21 PIN = –25 dBm 21 dB
Small signal gain variation ΔS21 Across all ZigBee channels 2 dBp-p
Saturated gain G_SAT POUT = +20 dBm 17 19 dB
2nd harmonic 2fo POUT = +20 dBm, IEEE 802.15.4 source –42 dBm/MHz
3rd harmonic2 3fo POUT = +20 dBm, IEEE 802.15.4 source –42 dBm/MHz
Output return loss2 S22 ANT1 or ANT2 port –10 –5 dB
Transmit port impedance2 ZIN 200 Ω
Turn-on time2 tRISE From 50% of CTX edge to 90% of final
RF output power
800
ns
Turn-off time2 tFALL From 50% of CTX edge to 10% of final
RF output power
800
ns
Stability2 Stab CW, Pin = 0 dBm, 0.1 GHz to 20 GHz,
load VSWR = 6:1
All non-harmonically related outputs
< –42 dBm/MHz
–
Ruggedness2 RU CW, Pin = +6 dBm, load VSWR = 10:1 No permanent damage –
AC Receive Characteristics
Frequency range f 2400 2483 MHz
Receive gain RX_GAIN 10.5 dB
Receive noise figure2 NF 2 dB
Third order input intercept point2 IIP3 –3 +1 dBm
1 dB input compression point IP1dB –13 –3 dBm
1 dB input compression point in bypass
mode2
IP1dB
+10
dBm
Input return loss2 S11 ANT1 or ANT2 ports –10 –5 dBm
Receive port impedance2 ZOUT Measured differentially between RXP
and RXN
200
Ω
Turn-on time2 tRISE From 50% of CTX edge to 90% of final
RF output power
800
ns
Turn-off time2 tFALL From 50% of CTX edge to 10% of final
RF output power
800
ns
Gain in bypass mode G_BP –3 dB
1 Performance is guaranteed only under the conditions listed in this table.
2 Not tested in production. Fully characterized and guaranteed by design.
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G
Table 6. SKY66109-11 Mode Control Logic1
(VCC1 = VCC2 = 3.0 V, TA = +25 C)
Mode Description
CPS
(Pin 18)
CSD
(Pin 17)
CTX
(Pin 20)
Typical Current
Consumption
0 All off (sleep mode)2 X 0 X 0.1 μA
1 Receive bypass mode 0 1 0 250 μA
2 Receive LNA mode 1 1 0 5 mA
4 Transmit mode X 1 1 30 mA
1 “0” = 0 V. “1” = +3.0 V. “X” = don’t care (must be either 0 V or Vcc voltage). Any state other than described in this table places the switch into an undefined
state. An undefined state will not damage the device.
2
Remove EVB pulldown resistors to achieve specified sleep current with CTX or CPS high.
Table 7. SKY66109-11 Antenna Enable Logic1
(VCC1 = VCC2 = 3.0 V, TA = +25 C)
Description
CPS
(Pin 18)
CSD
(Pin 17)
CTX
(Pin 20)
ANT_SEL
(Pin 14)
ANT1 port enabled X X X 0
ANT2 port enabled X X X 1
1 “0” = 0 V. “1” = +3.0 V. “X” = don’t care. Any state other than described in this table places the switch into an undefined state. An undefined state will not damage the device.
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 7
Evaluation Board Description
The SKY66109-11 Evaluation Board is used to test the
performance of the SKY66109-11 FEM. The board is optimized for
evaluation, experimentation, and investigation with an 802.15.4
signal source. The design and layout can be quickly and easily
transferred into a production design.
An Evaluation Board schematic diagram is provided in Figure 4. A
reference design schematic is provided in Figure 5. Table 8
describes the pins on the power and control I/O header (J5).
Table 9 provides the Bill of Materials (BOM) list for Evaluation
Board components. The Evaluation Board is shown in Figure 6.
Evaluation Board Setup Procedure
1. Connect J1, J2, J3, and J4 to 50 Ω instruments.
Terminate all unused ports (if applicable) with 50 Ω.
2. Connect the supply ground to pins 19 and 20 of J5.
3. Connect 3.0 V to pins 15 and 16 of J5.
4. Connect 3.0 V to pins 3 and 4 of J5.
NOTE: Pins 7 and 8 of J5 are left open.
NOTE: By following the logic in Table 6, the required RF path is
selected. Refer to Table 7 for antenna port control.
5. Monitor the 2.5 GHz amplifier transmit performance by
applying an RF signal to J3 and monitoring the output power on
J1 (ANT1) or J2 (ANT2).
CAUTION: Care should be taken not to overdrive the amplifier by
applying too much RF on the input to the device. A
suitable starting input power would be –20 dBm.
6. Monitor the 2.5 GHz amplifier receive performance by applying
an RF signal to J1 (ANT1) or J2 (ANT2) and monitoring the
output signal on J3.
Package Dimensions
The PCB layout footprint for the SKY66109-11 is provided in
Figure 7. Typical part markings are shown in Figure 8. Package
dimensions for the 20-pin MCM are shown in Figure 9, and tape
and reel dimensions are provided in Figure 10.
Package and Handling Information
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
The SKY66109-11 is rated to Moisture Sensitivity Level 3 (MSL3)
at 240 C. It can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
PCB Design and SMT Assembly/Rework Guidelines for MCM-L
Packages, document number 101752.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G
VCC
VDD
VB_OUT
VB_IN
CTX
CPS
CSD
VCC2
ANTSEL
2
4
6
8
10
12
14
16
18
20
1
3
5
7
9
11
13
15
17
19
VDD
VB_OUT
VB_IN
C1
2.2 μF
C2
2.2 μF
VCC
J5
VCC
C4
100 nF
C8
10 pF
CTX
R3
100K
R1
100K
R2
100K
CPS
CSD
C3
100 nF
C7
10 pF
R4
100K
VCC2
ANTSEL
J1
SMA
J2
SMA
VB_IN
VB_OUT
C5
10 pF
C6
10 pF
J4
SMA
J3
SMA
UN_BAL
RF_GND
BAL_PT
1
2
3
N/C
GND
BAL_PT
6
5
4
UN_BAL
RF_GND
BAL_PT
1
2
3
N/C
GND
BAL_PT
6
5
4
U3
U2
GND
TXP
TXN
VB_OUT
RXP
RXN
1
2
3
4
5
6
16
15
14
13
12
11
VCC2
GND
ANT_SEL
GND
ANT1
GND
7
8
9
10
VB_IN
GND
GND
ANT2
CTX
VCC1
CPS
CSD
20
19
18
17
Pad 21
SKY66109-11
U1
203034-004
Figure 4. SKY66109-11 Evaluation Board Schematic
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 9
VCC
C4
100 nF
C8
10 pF
CTX
CPS
CSD
C3
100 nF
C7
10 pF
VCC
ANTSEL
ANT1
ANT2
VB_IN
VB_OUT
GND
TXP
TXN
VB_OUT
RXP
RXN
1
2
3
4
5
6
16
15
14
13
12
11
VCC2
GND
ANT_SEL
GND
ANT1
GND
7
8
9
10
VB_IN
GND
GND
ANT2
CTX
VCC1
CPS
CSD
20
19
18
17
Pad 21
SKY66109-11
U1
203034-005
TXP
TXN
L2
RXP
RXN
L1
Figure 5. SKY66109-11 Reference Design Schematic
Table 8. Power and Analog I/O Header: J5, 10x2
Pin Pin Name Description Recommended Setting
1, 2, 15 VCC Supply voltage General purpose VCC provided as the main power supply
3, 4, 9, 11, 13, 17 VDD Digital supply voltage Connect to separate power supply voltage
5, 6 VB_OUT Bias output –
7, 8 VB_IN Bias voltage input No connect
16 VCC2 Supply voltage General purpose VCC provided as the main power supply
10 CTX Control
See Tables 6 and 7
12 CPS Control
14 CSD Control
18 ANT_SEL Control
19, 20 GND Ground General purpose ground
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
10 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G
Table 9. SKY66109-11 Evaluation Board Bill of Materials (BOM)
Component Value Size Manufacturer Manufacturer Part Number Characteristics
C1, C2 2.2 μF 0805 Murata GRM21BR71A225KA01L Ceramic capacitor, 2.2 μF, 10V,
10%, X7R 0805
C3, C4 100 nF 0402 Murata GRM155R71C104KA88D Monolithic ceramic
C5, C6, C7, C8 10 pF 0402 Murata GRM1555C1H100JZ01 Multilayer ceramic
J1, J2, J3, J4 SMA End launch Johnson
Components
142-0701-851 SMA end launch straight jack
receptacle – tab contact
J5 10X2 100 mil Samtec TSW-110-07-G-D 100 mil header
R1, R2, R3, R4 100 kΩ 0402 Panasonic ERJ2GEJ104 Thick film chip resistor
U1 – 3 x 4 mm MCM Skyworks Solutions,
Inc.
SKY66109-11 2.4 GHz ZigBee FEM with
differential transmit/receive
U2, U3 – 2 x 1.25 mm TDK HHM1521 Multilayer 2.4 GHz chip baluns
N
ote: Schematic and BOM have been designed to optimize performance in 802.11a/n applications.
203034-006
Figure 6. SKY66109-11 Evaluation Board
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 11
4.3 mm
20X 0.56 mm
3.3 mm
20X 0.25 mm
4X 0.59 mm
2X 0.4375 mm
2X 0.513 mm
Stencil Aperture
Top View
Stencil aperture size for
center ground pad should be
80% to 100% (by area) of the
solder mask opening
0.5 mm Pitch
Package Outline
Pin 20
Pin 1 Indicator
0.20 X 45°
Pin 1
0.5 mm Pitch
Package Outline
Pin 20
Pin 1 Indicator
0.20 X 45°
Pin 1
Solder Mask Opening
Top View
4.4 mm
20X 0.66 mm
20X 0.35 mm
4.3 mm
Package Outline
0.5 mm Pitch
Pin 20
Pin 1
Metallization
Top View
3.4 mm
2X 0.59 mm
Opening size of 60% to 100%
of exposed center opening shown
2.1045 mm
14X 0.56 mm
14X 0.25 mm
3.3 mm
Thermal via array
Ø
0.3 mm on 0.6 mm
pitch improves thermal performance
203034-007
Note:
Thermal vias should be resin filled and capped in accordance with
IPC-4761 Type VII vias. Recommended Cu thickness is 30 to 35 µm.
Figure 7. PCB Layout Footprint
Pin 1
Indicator
NOTE: Lines 1, 2, and 3 have a maximum of 7 characters
Line 1 = Part Number and Version
Line 2 = Lot Number
Line 3 = YEAR-WEEK-Country Code (MX)
203034-008
Line 1
Line 2
Line 3
Figure 8. Typical Part Markings
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
12 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G
4B
Pin 1
Indicator
C
3
Top View
0.15 A B C
Top
A
0.1
0.95 ±0.1
Side View Bottom View
20X SMT Pad
4X 0.25
4X 0.75
12X 1.4
See Detail B
4X 0.25
4X 0.75
4X 1.25
8X 1.9
0.577
0.577
0
0.1
M
A B C
Solder Mask Opening
0.2 A B C
0
A
Pin 20
Pin 1 Indicator
See Detail C
Pin 1
1.026
5X R0.05 Max
1.18
Solder Mask Edges 0.2 X 45°
Detail C
Pad
Scale: Full
1X This Rotation
0.875
Detail B
Pad
Scale: Full
1X This Rotation
1.18
Solder Mask Edges
4X R0.05 Max
(0.1)
0.31 ±0.1
0.35 ±0.05
0.25 ±0.05
(0.05)
Metal Pad Edge
Detail A
Pad
Scale: 2X
4X This Rotation
4X Rotated 180°
Notes (Unless Otherwise Specified):
1. Dimensions and tolerances are in accordance with ASME Y14.5M–1994.
2. Dimensions are in millimeters.
203034-009
Figure 9. SKY66109-11 Package Dimensions
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
203034G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • June 3, 2016 13
8.00
3.40
4.40
1.10
2.00 ± 0.05 (Note 3)
0.30 ± 0.05
R0.3 Max.
4.00 (Note 1)
0.12
R0.25
0.12
∅1.50 Min
∅1.5 +0.1/–0.0
12.0 ± 0.30
1.75 ± 0.10
Pin 1 Indicator
5.50 ± 0.05
(Note 3)
A
Notes:
1. 10 sprocket hole pitch cumulative tolerance
±
0.2 mm.
2. Camber in compliance with EIA 481.
3. Pocket position relative to sprocket hole measured
as true position of pocket, not pocket hole.
4. All measurements are in millimeters.
A
A
203034-010
Figure 10. SKY66109-11 Tape and Reel Dimensions
DATA SHEET • SKY66109-11: ZIGBEE/SMART ENERGY FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
14 June 3, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203034G
Ordering Information
Model Name Manufacturing Part Number Evaluation Board Part Number
SKY66109-11: Zigbee/Smart Energy FEM SKY66109-11 SKY66109-11-EK1
Copyright © 2013-2015 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for
identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by
reference.
