Features * Fast read access time - 55ns * Low-power CMOS operation * * * * * * * * * - 100A max standby - 40mA max active at 5MHz JEDEC standard packages - 40-lead PDIP - 44-lead PLCC Direct upgrade from 512Kbit, 1Mbit, and 2Mbit Atmel(R) AT27C516, AT27C1024, and AT27C2048) EPROMs 5V 10% supply High-reliability CMOS technology - 2,000V ESD protection - 200mA latchup immunity Rapid programming algorithm - 50s/word (typical) CMOS- and TTL-compatible inputs and outputs Integrated product identification code Industrial temperature range Green (Pb/halide-free) packaging option 1. 4Mb (256K x 16) One-time Programmable, Read-only Memory Atmel AT27C4096 Description The Atmel AT27C4096 is a low-power, high-performance, 4,194,304-bit, one-time programmable, read-only memory (OTP EPROM) organized as 256K by 16 bits. It requires a single 5V power supply in normal read mode operation. Any word can be accessed in less than 55ns, eliminating the need for speed reducing WAIT states. The x16 organization makes this part ideal for high-performance, 16- and 32-bit microprocessor systems. In read mode, the AT27C4096 typically consumes 15mA. Standby mode supply current is typically less than 10A The AT27C4096 is available in industry-standard, JEDEC-approved, one-time programmable (OTP) PDIP and PLCC packages. The device features two-line control (CE, OE) to eliminate bus contention in high speed systems. With high-density 256K word storage capability, the AT27C4096 allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. The AT27C4096 has additional features that ensure high quality and efficient production use. The rapid programming algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 50s/word. The Integrated product identification code electronically identifies the device and manufacturer. This feature is used by industry-standard programming equipment to select the proper programming algorithms and voltages. 0311J-EPROM-4/11 Pin configurations A0 - A17 Addresses O0 - O15 Outputs CE Chip enable OE Output enable NC No connect Both GND pins must be connected O12 O11 O10 O9 O8 GND NC O7 O6 O5 O4 7 8 9 10 11 12 13 14 15 16 17 39 38 37 36 35 34 33 32 31 30 29 O3 O2 O1 O0 OE NC A0 A1 A2 A3 A4 Note: 40-lead PDIP Top view 44-lead PLCC Top view O13 O14 O15 CE VPP NC VCC A17 A16 A15 A14 Function 6 5 4 3 2 1 44 43 42 41 40 Pin name 18 19 20 21 22 23 24 25 26 27 28 2. 3. A13 A12 A11 A10 A9 GND NC A8 A7 A6 A5 VPP CE O15 O14 O13 O12 O11 O10 O9 O8 GND O7 O6 O5 O4 O3 O2 O1 O0 OE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 VCC A17 A16 A15 A14 A13 A12 A11 A10 A9 GND A8 A7 A6 A5 A4 A3 A2 A1 A0 System considerations Switching between active and standby conditions via the chip enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed datasheet limits, resulting in device nonconformance. At a minimum, a 0.1F, high-frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7F bulk electrolytic capacitor should be utilized, again connected between the VCC and ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array. Figure 3-1. 2 Block diagram Atmel AT27C4096 0311J-EPROM-4/11 Atmel AT27C4096 4. Absolute maximum ratings* *NOTICE: Temperature under bias . . . . . . . . . . . . . -55C to +125C Storage temperature . . . . . . . . . . . . . . . . -65C to +150C Voltage on any pin with respect to ground . . . . . . . . . . . . . . . . . . . -2.0V to +7.0V(1) Stresses beyond those listed under "Absolute maximum ratings" may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Voltage on A9 with respect to ground . . . . . . . . . . . . . . . . . -2.0V to +14.0V(1) VPP supply voltage with respect to ground . . . . . . . . . . . . . . . . . . -2.0V to +14.0V(1) Note: 5. 1. Maximum voltage is -0.6V DC, which may undershoot to -2.0V for pulses of less than 20ns. Maximum output pin voltage is VCC + 0.75V DC, which may overshoot to +7.0V for pulses of less than 20ns. DC and AC characterisitcs Table 5-1. Operating modes Mode/Pin CE OE Ai VPP (1) Read VIL VIL Ai Output disable X VIH X Outputs X DOUT X High Z (5) Standby VIH X X X High Z Rapid program(2) VIL VIH Ai VPP DIN PGM verify VIH VIL Ai VPP DOUT PGM inhibit VIH VIH X VPP High Z VCC Identification code (3) Product identification(4) Notes: VIL VIL A9 = VH A0 = VIH or VIL A1 - A17 = VIL 1. X can be VIL or VIH. 2. Refer to the Programming characteristics. 3. VH = 12.0 0.5V. 4. Two identifier words may be selected. All Ai inputs are held low (VIL), except A9, which is set to VH, and A0, which is toggled low (VIL) to select the manufacturer's identification word and high (VIH) to select the device code word. 5. Standby VCC current (ISB) is specified with VPP = VCC. VCC > VPP will cause a slight increase in ISB. Table 5-2. DC and AC operating conditions for read operation Atmel AT27C4096 Industrial operating temperature (case) VCC power supply -55 -90 -40C - 85C -40C - 85C 5V 10% 5V 10% 3 0311J-EPROM-4/11 Table 5-3. DC and operating characteristics for read operation Symbol Parameter Condition ILI Input load current Output leakage current ILO IPP1 (2) VPP (1) read/standby current VCC(1) standby current ISB Min Max Units VIN = 0V to VCC 1 A VOUT = 0V to VCC 5 A VPP = VCC 10 A ISB1 (CMOS) CE = VCC 0.3V 100 A ISB2 (TTL) CE = 2.0 to VCC + 0.5V 1 mA f = 5MHz, IOUT = 0mA, CE = VIL 40 mA ICC VCC active current VIL Input low voltage -0.6 0.8 V VIH Input high voltage 2.0 VCC + 0.5 V VOL Output low voltage IOL = 2.1mA 0.4 V VOH Output high voltage IOH = -400A Notes: 2.4 V 1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP. 2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and IPP. Table 5-4. AC characteristics for read operation Atmel AT27C4096 -55 Symbol Parameter Condition tACC(1) Address to output delay CE = OE = VIL tCE(1) CE to output delay tOE(1) OE to output delay tDF(1) OE or CE high to output float, whichever occurred first tOH(1) Output hold from address, CE or OE, whichever occurred first Note: 4 Min -90 Max Units 55 90 ns OE = VIL 55 90 ns CE = VIL 20 35 ns 20 20 ns 7 Max Min 0 ns 1. See the AC waveforms for read operation diagram. Atmel AT27C4096 0311J-EPROM-4/11 Atmel AT27C4096 Figure 5-1. Notes: AC waveforms for read operation(1) 1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE. 3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC. 4. This parameter is only sampled, and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. Figure 5-2. Input test waveforms and measurement levels For -55 devices only: tR, tF < 5ns (10% to 90%) For -90 devices: tR, tF < 20ns (10% to 90%) Figure 5-3. Output test load 1.3V (1N914) OUTPUT PIN 3.3K CL Note: CL = 100pF including jig capacitance. 5 0311J-EPROM-4/11 Table 5-5. Pin capacitance f = 1MHz, T = 25C(1) Symbol Typ Max Units Conditions CIN 4 10 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 1. Typical values for nominal supply voltage. This parameter is only sampled, and is not 100% tested. Figure 5-4. Notes: Programming waveforms(1) 1. The input timing reference is 0.8V for VIL and 2.0V for VIH. 2. tOE and tDFP are characteristics of the device, but must be accommodated by the programmer. 3. When programming the Atmel AT27C4096, a 0.1F capacitor is required across VPP and ground to suppress spurious voltage transients. 6 Atmel AT27C4096 0311J-EPROM-4/11 Atmel AT27C4096 Table 5-6. DC programming characteristics TA = 25 5C, VCC = 6.5 0.25V, VPP = 13.0 0.25V Limits Symbol Parameter Test conditions ILI Input load current VIN = VIL, VIH VIL Input low level VIH Input high level VOL Output low voltage IOL = 2.1mA VOH Output high voltage IOH = -400A ICC2 VCC supply current (program and verify) IPP2 VPP supply current VID A9 product identification voltage Table 5-7. Min Max Units 10 A -0.6 0.8 V 2.0 VCC + 0.7 V 0.4 V 2.4 V CE = VIL 11.5 50 mA 30 mA 12.5 V Max Units AC programming characteristics TA = 25 5C, VCC = 6.5 0.25V, VPP = 13.0 0.25V Limits Symbol Parameter Test conditions tAS Address setup time tOES OE setup time tDS Data setup time tAH Address hold time tDH Data hold time tDFP OE high to output float delay(2) tVPS VPP setup time tVCS VCC setup time Min 2 s 2 s 2 s 0 s Input pulse levels 0.45V to 2.4V 2 s Input timing reference level: 0.8V to 2.0V 2 s 2 s Input rise and fall times : (10% to 90%) 20ns 0 (3) tPW CE program pulse width tOE Data valid from OE tPRT VPP pulse rise time during programming Notes: (1) 130 47.5 Output timing reference level 0.8V to 2.0V ns 52.5 s 150 ns 50 ns 1. VCC must be applied simultaneously with or before VPP and removed simultaneously with or after VPP. 2. This parameter is only sampled, and is not 100% tested. Output float is defined as the point where data is no longer driven. See timing diagram. 3. Program pulse width tolerance is 50s 5%. Table 5-8. The Atmel AT27C4096 intergrated product identification code Pins Codes A0 O15-O8 O7 O6 O5 O4 O3 O2 O1 O0 Hex data Manufacturer 0 0 0 0 0 1 1 1 1 0 001E Device type 1 0 1 1 1 1 0 1 0 0 00F4 7 0311J-EPROM-4/11 6. Rapid programming algorithm A 50s CE pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 50s CE pulse without verification. Then a verification/reprogramming loop is executed for each address. In the event a word fails to pass verification, up to 10 successive 50s pulses are applied with a verification after each pulse. If the word fails to verify after 10 pulses have been applied, the part is considered failed. After the word verifies properly, the next address is selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All words are read again and compared with the original data to determine if the device passes or fails. Figure 6-1. 8 Rapid programming algorithm Atmel AT27C4096 0311J-EPROM-4/11 Atmel AT27C4096 7. Ordering information Green Package (Pb/halide-free) ICC (mA) tACC (ns) Active Standby Atmel ordering code Package Lead finish Operation range 55 40 0.1 AT27C4096-55JU 44J Matte tin Industrial (-40C to 85C) 90 40 0.1 AT27C4096-90JU AT27C4096-90PU 44J 40P6 Matte tin Industrial (-40C to 85C) Package type 44J 44-lead, plastic, J-leaded chip carrier (PLCC) 40P6 40-lead, 0.600" wide, plastic, dual inline package (PDIP) 9 0311J-EPROM-4/11 8. Packaging information 44J - PLCC 1.14(0.045) X 45 PIN NO. 1 1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075) IDENTIFIER E1 E D2/E2 B1 B e A2 D1 A1 D A 0.51(0.020)MAX 45 MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-018, variation AC 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102mm) maximum SYMBOL MIN NOM MAX A 4.191 - 4.572 A1 2.286 - 3.048 A2 0.508 - - D 17.399 - 17.653 D1 16.510 - 16.662 E 17.399 - 17.653 E1 16.510 - 16.662 D2/E2 14.986 - 16.002 B 0.660 - 0.813 B1 0.330 - 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 Package drawing contact: packagedrawings@atmel.com 10 TITLE 44J, 44-lead, plastic J-leaded chip carrier (PLCC) DRAWING NO. 44J REV. B Atmel AT27C4096 0311J-EPROM-4/11 Atmel AT27C4096 40P6 - PDIP D PIN 1 E1 A SEATING PLANE A1 L B B1 e E 0 ~ 15 C eB Notes: 1. This package conforms to JEDEC reference MS-011, variation AC 2. Dimensions D and E1 do not include mold flash or protrusion. mold flash or protrusion shall not exceed 0.25mm (0.010"). COMMON DIMENSIONS (Unit of Measure = mm) REF SYMBOL MIN NOM MAX A - - 4.826 A1 0.381 - - D 52.070 - 52.578 E 15.240 - 15.875 E1 13.462 - 13.970 B 0.356 - 0.559 B1 1.041 - 1.651 L 3.048 - 3.556 C 0.203 - 0.381 eB 15.494 - 17.526 e NOTE Note 2 Note 2 2.540 TYP 09/28/01 Package drawing contact: packagedrawings@atmel.com TITLE 40P6, 40-lead (0.600"/15.24mm wide) Plastic dual inline package (PDIP) DRAWING NO. 40P6 REV. B 11 0311J-EPROM-4/11 9. 12 Revision history Doc. rev. Date 0311J 04/2011 0311I 12/2007 Comments Remove VSOP package Add lead finish to ordering information Atmel AT27C4096 0311J-EPROM-4/11 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1) (408) 441-0311 Fax: (+1) (408) 487-2600 www.atmel.com Atmel Asia Limited Unit 01-5 & 16, 19F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel: (+81) (3) 3523-3551 Fax: (+81) (3) 3523-7581 (c) 2011 Atmel Corporation. All rights reserved. / Rev.: 0311J-EPROM-4/11 Atmel(R), logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.