BMK60000 - Red Lion Controls

MODEL BMK6 & BMK7A - BASE MOUNT KIT FOR CUB4, CUB5 & DT8 UNITS

UNIT

LATCHING

FEATURE

GASKET

BASE

MOUNT

LATCHING

FEATURE

NUT

FASTENER

MOUNTING

SCREW

GROMMET

HOLE

(57.15)

(73.15)

(63.50)

(73.66) (57.15)

(82.55)

(88.90)

2.50

2.25

2.90

3.25

3.50

2.25

2.88

2.25 3.38

2.88

3.25

(85.85)

3.50

(88.90)

4.00

(101.50)

(57.15)

(73.15)

4.62

(117.35)

(82.55)

BMK7A - CLOSED BASE MOUNT KIT

(With or Without MLPS)

BMK6 - OPEN BASE MOUNT KIT

(Without MLPS)

DIMENSIONS In inches (mm)

Bulletin No. BMK6/7-F

Drawing No. LP0392

Released 12/14

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

DESCRIPTION

The BMK6 and BMK7A base mounts are designed for use with the CUB4,

CUB5, and DT8 units. The BMK7A is large enough to accommodate a Micro-

line Power Supply (MLPS) attached to a CUB4, CUB5 or DT8.

The base mounts are constructed of steel with a textured black finish. Wiring

can either be brought through the panel on which the unit is mounted, or through

the hole(s) in the enclosure itself. Grommets are provided to insert in the hole(s)

on the base mount (where applicable) when wires are routed through it. The

grommets are in the accessory bag with each base mount unit, along with four

nuts and bolts for mounting.

INSTALLATION

BMK6 - Open Base Mount

Before attaching the BMK6 to the panel or frame, it is recommended to wire and mount

the unit to ensure good electrical connections. The following steps outline the most

common sequence for installing a unit without an MLPS attached.

1. Install the grommet (provided in the accessory bag) in the hole in the base mount.

2. Assemble nut fastener and mounting screw onto both sides of the mounting clip.

The tip of the screw should not project from the hole in mounting clip.

3. Slide the panel gasket over the rear of the unit to the back of the bezel.

Then install the unit through the opening in the front of the base

mount until the bezel flange makes contact.

4. Slide the mounting clip over the rear of the unit until the

mounting clip is against the inside of the base mount.

The mounting clip has latching features which engage

into mating features on the unit’s housing.

Note: It is necessary to hold the unit in place when sliding

the mounting clip into position.

5. Alternately tighten each screw to ensure uniform gasket

compression.

6. Connect the necessary wires from the grommet to the unit.

7. Mount the base mount enclosure to the panel or frame as application

requires. Four bolts and nuts are provided with the Base Mount Kit.

INSTALLATION

BMK7A - Closed Base Mount

Before attaching the BMK7A to the panel or frame, it is recommended to

wire and mount the unit to ensure good electrical connections. The following

steps outline the most common sequence for installing a unit with an MLPS

attached.

1. Install the grommets (provided in the accessory bag) in the holes in the

base mount.

2. Slide the panel gasket over the rear of the unit to the back of

the bezel.

3. Remove the common and V+ screw

terminals from the rear of the unit

(save for later use), and replace

them with the hex drive stand-

offs with round washers

(supplied with the MLPS).

4. Assemble nut fastener and

mounting screw onto both

sides of the mounting clip.

The tip of the screw should

not project from the hole in

mounting clip.

5. Route the wires from the

grommets, through the

mounting clip, into the rear

of the base mount and out

the front.

6. Connect the wires necessary for the application to the unit.

7. Install the unit through the opening in the front of the base mount until the

bezel flange makes contact.

8. Slide the mounting clip over the rear of the unit until the mounting clip is

against the inside of the base mount. The mounting clip has latching

features which engage into mating features on the unit’s housing.

Note: It is necessary to hold the unit in place when sliding the mounting

clip into position.

9. Alternately tighten each screw to ensure uniform gasket compression.

10. Connect AC power to the terminal block of the MLPS.

Note: Make sure the AC selector switch is set to the appropriate position

before applying power to the unit.

11. Mount the MLPS and optional sensor wires needed to the stand-offs using

the screw terminal from the unit with the supplied square washers.

12. Mount the base mount enclosure to the panel or frame as application

requires. Four bolts and nuts are provided with the Base Mount Kit.

MLPS

SCREW TERMINALS

FROM REAR OF UNIT

SQUARE

WASHER

HEX STAND-OFF (2 TYP)

LATCHING

FEATURE

MOUNTING

CLIP

BASE MOUNT

GASKET

LATCHING

FEATURE

UNIT

MOUNTING SCREW

NUT

FASTENER

ORDERING INFORMATION

MODEL NO DESCRIPTION PART NUMBER

BMK

OPEN BASE MOUNT KIT BMK60000

CLOSED BASE MOUNT KIT BMK7A000

Red Lion Controls

Headquarters

20 Willow Springs Circle

York PA 17406

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

Red Lion Controls

China

Unit 302, XinAn Plaza

Building 13, No.99 Tianzhou Road

ShangHai, P.R. China 200223

Tel +86 21 6113 3688

Fax +86 21 6113 3683

Red Lion Controls

Europe

Softwareweg 9

NL - 3821 BN Amersfoort

Tel +31 (0) 334 723 225

Fax +31 (0) 334 893 793

Red Lion Controls

India

201-B, 2nd Floor, Park Centra

Opp 32 Mile Stone, Sector-30

Gurgaon-122002 Haryana, India

Tel +91 984 487 0503