B2-44 APEM www.apem.com
B2
13000 series
Professional quick-break momentary pushbutton switches
Distinctive features and specifications
❑ PC and panel mount models
❑ Bushing Ø 6,35 (1/4) and 11,9 (15/32)
❑ UL and CECC approved
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load :
- silver contacts (A-AD2) : 4A 30VDC
- gold plated contacts (CD) : 100mA 30V
• Minimum load (AD2-CD contacts) : 10mA 50mV, 10µA 5V min.
• Initial contact resistance : 10 mΩ max.
• Insulation resistance : 1.000 MΩ min. at 500VDC
• Dielectric strength :
1.000 Vrms 50 Hz min. between terminals
2.000 Vrms 50 Hz min. between poles and between terminals and frame
• Contact bounce : 2 ms max.
• Electrical life :
Contacts Max. current/voltage rating Number of cycles
A 4A 30VDC 50.000
AD2 4A 30VDC 20.000
(gold plating : 100mA 30VDC max.)
CD 100mA 30VDC 50.000
Low level or mechanical life 150.000
MATERIALS
• Case : diallylphthalate (DAP)
• Actuator : brass, nickel plated
• Bushing : brass, nickel plated
• Housing : brass, nickel plated
• Contacts : A: silver
AD2 : silver, gold plated
(2 micron gold)
CD : brass, gold plated
• Terminal seal : epoxy
Note : AD2 contacts can be used for high level applications.In this case, the
gold layer is considered only as a protection against oxidation during
storage.
GENERAL SPECIFICATIONS
• Torque : 1,25 Nm (.922 Ft.lb)
max. applied to nut
• Standard panel thickness : 2 mm
(.078 ) max.
• Total travel : 2 mm (.078)
• Operating temperature :
-40°C to +85°C
The company reserves the right to change specifications without notice.
UG1410A-R1
APEM www.apem.com B2-45
B2
13000 series
Professional quick-break momentary pushbutton switches
Specifications
AGENCY APPROVALS
2A 125VAC/250VAC CECC 96401-001
Designed to MIL specifications
Availability :
UL : all models with silver or gold plated silver contacts
CECC : consult factory for details of approved models.
Marking : to order switches marked UL or CECC, complete appropriate box
of ordering format.
Dimensions : first dimensions are in mm while inches are shown as bracketed numbers.
Sealing boots are available to protect the switches against dust and water. They are presented in section H.
Mounting accessories : standard hardware supplied with all models : 2 hex nuts 8 mm (.314) across flats, 1 locking ring and
1 lockwasher.
Standard and special hardware available are presented in section I.
Packaging unit : 50 pieces.
RELIABILITY - RUN-IN TEST
Upon request, each individual switch can be submitted to a low level run-in
test of 50 or 250 cycles to ensure suitability for special applications requiring
a very high level of reliability (military, space,etc.).
B2-46 APEM www.apem.com
B2
13000 series
Professional quick-break momentary pushbutton switches
Overview
13
SERIES
Terminals and bushing
2Straight PC terminals,
bushing Ø 6,35 (1/4)
4Solder lugs, bushing Ø 6,35
(1/4) or 11,9 (15/32)
Right angle terminals,
bushing Ø 6,35 (1/4)
No of poles
3Single pole
4Double pole
Electrical function
5ON - MOM
Terminals
Blank Solder lugs or straight PC
depending on model
WRight angle, horizontal
mounting
Plungers
Blank Standard for Ø 6,35
(1/4) bushing
-4 4 mm (.157) long, for
Ø 11,9 (15/32)
bushing (X768)
-99 mm (.354) long, for
Ø 11,9 (15/32)
bushing (X768)
Sealing
Blank Epoxy sealed
terminals standard
KFront panel sealing by
one O-ring and
sealing washer
Reinforced sealing, see X640
under "Special options".
Approvals
UL
CECC
Availability :
Consult factory for
details of approved
models.
Contact materials
ASilver
AD2 Silver, gold plated
(2 micron gold)
CD Brass, gold plated
Finish
Blank Brass, nickel plated
GBlack finish on
bushing, plunger and
hardware
Special options
Blank No special
requirement
X640 Reinforced sealing
by three O-rings
X768 Bushing Ø 11,9
(15/32) + front
panel sealing
(double pole only)
Caps
U900 Ø 5 (.196)
U1140 Ø 8 (.314)
U1720 Ø 9,4 (.370)
U480 Ø 10 (.393) std
U630 Ø 15 (.590)
U2430 Square, height
4 (.157)
U2020 Square, height
6 (.236)
For models with Ø 4
(.157) plunger only.
ABOUT THIS SERIES
On the following pages, you will find successively :
- model structure of switches
- options in the same order as in above chart
NOTICE : please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
Order
separately.
APEM www.apem.com B2-47
B2
13000 series
Professional quick-break momentary pushbutton switches
Solder lug terminals : 13400 - Straight PC terminals : 13200
Straight PC terminals : 13200
Solder lug terminals : 13400
MODEL
STRUCTURE
1-3 1-2
Single pole
13435 ON MOM
Double pole
13445 ON MOM
1-3 1-2
Single pole
13235 ON MOM
Double pole
13245 ON MOM
• Threaded bushing Ø 6,35 mm (1/4)
• Epoxy sealed terminals standard
PANEL CUT-OUT
13400 - 13200
With KWith X640
Standard sealing option sealing option
➞Keyway
➞Keyway
➞Keyway
1 23
(.374)
(.039)
9.50
1.00
(.098)
(.047)
(.066)
(.196)
1.70
5.00
1.20
2.50
(.196)
(.157 DIA)
(.019)
(.236)(.248)
(.551)
(.236)
(.098)
EPOXY
(.314)
2.50
8.00
Ø4.00
0.50 6.00
14.00
6.30 6.00
5.00
(.027)
(.527)
13.40
0.70
1 2 3
(.157)
4.00
Ø6.35-40UNS
(1/4-40UNS)
6.00
14.00
Ø4.00
8.00
(.314) (.551)
(.236)
(.157 DIA)
6.30
(.248)
9.50
(.374)
EPOXY
(.236)
(.157)
(.039)
(.019)
(.157)
(.236)
(.157)
(.062 DIA)
1.00 4.00
0.50 6.00
6.00
Ø1.6
4.00
4.00
(.027)
(.527)
13.40
0.70
1 2 3
(1/4-40UNS)
Ø6.35-40UNS
Ø6.50
Ø2.20
5.20
(.255 DIA) (.086 DIA)
(.204)
(.255 DIA)
Ø6.50
1.10
2.70
(.106)
(.043)
Standard
(.106)
2.70
Ø6.50
(.255 DIA)
KX640
B2-48 APEM www.apem.com
B2
13000 series
Professional quick-break momentary pushbutton switches
Right angle terminals : 13400W
Right angle terminals - single pole
1-3 1-2
13435W ON MOM
Panel cut-out, see previous page.
CONTACT MATERIALS
ASilver
AD2 Silver, gold plated (2 micron gold)
CD Brass, gold plated
PLUNGER
Blank Standard plunger for Ø 6,35 (1/4) bushing
-4 4 mm (.157) long plunger for Ø 11,9 (15/32) bushing (X768 option)
-9 9 mm (.354) long plunger for Ø 11,9 (15/32) bushing (X768 option)
Dash compulsory before plunger code.
➞Keyway
(.157 DIA)
(.019)
(.157)
(.232) (.236)
(.527)
(.102)
(.039)
(.364)
(.015)
(.173)
0.40
9.27
2.60
1.00
5.90 6.00
13.40
4.40
4.00
Ø4.00
0.50
Ø6.35-40UNS
(1/4-40UNS)
CD13WDT- A
(.027)
0.70
1
EPOXY
4.00
(.157)
(.314)
8.00
4.00
Ø1.6
(.062 DIA)
(.157)
5.08
(.200)
CD13WDT INDICE A
ECHELLE:0.65
9.27
(.364)
23
14.20
(.559)
APEM www.apem.com B2-49
B2
13000 series
Professional quick-break momentary pushbutton switches
Blank Bright chrome finish
GBlack finish on bushing, actuator and hardware
FINISH
SEALING
KFront panel sealing by one O-ring and sealing washer. Protects the
switch against water and dust.
Panel seal withstands 1 bar pressure and remains sealed even when
switch is operated.
Reinforced sealing : see X640 under "Special options".
SPECIAL OPTIONS
X640 Front panel sealing by three O-rings. Flatted bush for precise orientation.
Protects the switch against water and dust.
Panel seal withstands 1 bar pressure and remains sealed even when switch
is operated.
X935 C-ring on plunger for positive stop
Available on models with Ø 6,35 (1/4) bushing only.
➀ O-ring ➁ Sealing washer
➀ O-ringsX640
(.417 DIA)
(.464 DIA)
(.228 DIA)
(.251 DIA) (.090)
Ø10.60
Ø11.80
Ø5.80
2.30
Ø6.40
1
2
(.078 MAX)
2.00 Maxi
1
(.157 MAX)
4.00 Maxi
B2-50 APEM www.apem.com
B2
13000 series
Professional quick-break momentary pushbutton switches
UL
CECC CECC 96401-001
AGENCY APPROVALS
1-3 1-2
With short plunger
13445 -4 X768 ON MOM
With long plunger
13445 -9 X768 ON MOM
X768 Sealed switch with Ø 11,9 (15/32) flatted bushing. Chrome plated actuator. Solder lug terminals,
double pole. Contact and finish options available.
Security cap for this model : see section I.
➞Flat
Short (-4) Long (-9)
Availability :
UL : all models with silver or gold plated silver contacts
CECC : consult factory for details of approved models.
Marking : to order switches marked UL or CECC, please complete above box with desired approval.
Blank : no agency approval required.
APEM www.apem.com B2-51
B2
13000 series
Professional quick-break momentary pushbutton switches
DRESS NUTS
Chrome plated
Dress nuts are to be ordered separately.
U1636 U840 U825
For cap U1140 For cap U480 For cap U630
For models with Ø 6,35 (1/4) bushing only.
CAPS
U900 U1140 U1720
U480 U630
U2020 U2430
Cap colours
Replace last
"0" by number
1blue
1/4 dark blue
2black
3green
4grey
5yellow
6red
7ivory
7/1 white
9orange
Standard
Square Square
For models with Ø 6,35 (1/4)
bushing only.
(.157)
(.196)
(.129)
4.00
3.30
Ø5.00
(.118)
(.393)
(.295)
Ø10.00
7.50
3.00
(.236)
(.452 SQ)
(.195)
6.00
5.00
11.50x11.50
(.322 DIA)
(.500 DIA)
(1/4-40UNS)
(.322)
(.244)
Ø12.70
Ø8.20
6.20
8.20
Ø6.35-40UNS
(.413 DIA)
(.531 DIA)
(.314)
(.228)
Ø10.50
Ø13.50
5.80
8.00
Ø6.35-40UNS
(1/4-40UNS)
(.610 DIA)
(.728 DIA)
Ø18.50
Ø15.50
Ø6.35-40UNS
(1/4-40UNS)
8.00
(.314)
(.228)
5.80
(.452 SQ)
(.157)
(.196)
4.00
3.00
11.50x11.50
(.590 DIA)
(.393)
(.118)
3.00
10.00
Ø15.00
(.250)
(.314)
(.118)
3.00
6.35
Ø8.00
(.118)
(.370)
(.250)
3.00
6.35
Ø9.40
Order separately.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Apem:
13435A 13440AD2G25X822+U4546 13235A 13435AK 13445A 13435AD2 13445AD2G 13445AX640 13235CDK
13445AG9X768 13435AD2GX640 13445AD2K 13445AD24X768 13445A4GX768 13435AD2GX657
13445AD29GX768 13435CDGX640 13445AD2GX657+U486 13435CDGK 13440AD2G25X1156+U4546
13440AD2G25X1156 13440AD2G25X822 13435AD2GK 13445AD2GX657