CY14B108K, CY14B108M 8 Mbit (1024K x 8/512K x 16) nvSRAM with Real Time Clock Features Watchdog Timer 25 ns and 45 ns Access Times Clock Alarm with Programmable Interrupts Internally Organized as 1024K x 8 (CY14B108K) or 512K x 16 (CY14B108M) Capacitor or Battery Backup for RTC Industrial Temperature Hands Off Automatic STORE on Power Down with only a Small Capacitor 44 and 54-pin TSOP II Package STORE to QuantumTrap Nonvolatile Elements is Initiated by Software, Device Pin, or AutoStore on Power Down Pb-free and RoHS Compliance RECALL to SRAM Initiated by Software or Power Up High Reliability Infinite Read, Write, and RECALL Cycles 1 Million STORE Cycles to QuantumTrap 20 year Data Retention Single 3V +20%, -10% Operation Data Integrity of Cypress nvSRAM Combined with Full Featured Real Time Clock (RTC) Functional Description The Cypress CY14B108K/CY14B108M combines a 8-Mbit nonvolatile static RAM with a full featured RTC in a monolithic integrated circuit. The embedded nonvolatile elements incorporate QuantumTrap technology producing the world's most reliable nonvolatile memory. The SRAM is read and written infinite number of times, while independent nonvolatile data resides in the nonvolatile elements. The RTC function provides an accurate clock with leap year tracking and a programmable, high accuracy oscillator. The alarm function is programmable for periodic minutes, hours, days, or months alarms. There is also a programmable watchdog timer for process control. Logic Block Diagram[1, 2, 3] A0 A1 A2 A3 A4 A5 A6 A7 A8 A17 A 18 VCC Quatrum Trap 2048 X 2048 X 2 R O W V CAP POWER CONTROL STORE VRTCbat VRTCcap RECALL D E C O D E R STATIC RAM ARRAY 2048 X 2048 X 2 STORE/RECALL CONTROL SOFTWARE DETECT HSB A14 - A2 A 19 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 RTC I N P U T B U F F E R S Xout Xin INT COLUMN I/O MUX A19- A 0 OE COLUMN DEC WE DQ12 DQ13 CE DQ14 BLE A9 A10 A11 A 12 A13 A14 A15 A 16 DQ15 BHE Notes 1. Address A0 - A19 for x8 configuration and Address A0 - A18 for x16 configuration. 2. Data DQ0 - DQ7 for x8 configuration and Data DQ0 - DQ15 for x16 configuration. 3. BHE and BLE are applicable for x16 configuration only. Cypress Semiconductor Corporation Document #: 001-47378 Rev. *D * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised December 15, 2009 [+] Feedback CY14B108K, CY14B108M Contents Features .............................................................................. 1 Functional Description ...................................................... 1 Logic Block Diagram[1, 2, 3] ............................................ 1 Contents ............................................................................. 2 Pinouts ............................................................................... 3 Device Operation ............................................................... 4 SRAM Read ........................................................................ 4 SRAM Write ........................................................................ 4 AutoStore Operation ......................................................... 4 Hardware STORE (HSB) Operation .................................. 5 Hardware RECALL (Power Up) ......................................... 5 Software STORE ................................................................ 5 Software RECALL .............................................................. 5 Preventing AutoStore ........................................................ 6 Data Protection .................................................................. 7 Noise Considerations ........................................................ 7 Best Practices .................................................................... 7 Real Time Clock Operation ............................................... 8 nvTime Operation......................................................... 8 Clock Operations.......................................................... 8 Reading the Clock ........................................................ 8 Setting the Clock .......................................................... 8 Backup Power .............................................................. 8 Stopping and Starting the Oscillator............................. 8 Calibrating the Clock .................................................... 9 Alarm ............................................................................ 9 Watchdog Timer ........................................................... 9 Power Monitor ............................................................ 10 Interrupts .................................................................... 10 Flags Register ............................................................ 10 Document #: 001-47378 Rev. *D Maximum Ratings .............................................................16 Operating Range ...............................................................16 DC Electrical Characteristics ..........................................16 Data Retention and Endurance .......................................17 Capacitance ......................................................................17 Thermal Resistance ..........................................................17 AC Test Conditions ..........................................................17 RTC Characteristics .........................................................18 AC Switching Characteristics .........................................19 Switching Waveforms ......................................................19 Switching Waveforms ......................................................20 Switching Waveforms ......................................................21 AutoStore/Power Up RECALL .........................................22 Switching Waveforms ......................................................22 Software Controlled STORE and RECALL Cycle ..........23 Hardware STORE Cycle ...................................................24 Truth Table For SRAM Operations ..................................25 For x8 Configuration.................................................... 25 For x16 Configuration.................................................. 25 Part Numbering Nomenclature ........................................26 Ordering Information ........................................................27 Package Diagrams ............................................................28 Document History Page ...................................................30 Sales, Solutions, and Legal Information ........................31 Worldwide Sales and Design Support......................... 31 Products .......................................................................31 Page 2 of 31 [+] Feedback CY14B108K, CY14B108M Pinouts Figure 1. Pin Diagram: 44-PIn and 54-Pin TSOP II INT [4] NC A0 A1 A2 A3 A4 CE DQ0 DQ1 VCC VSS DQ2 DQ3 WE A5 A6 A7 A8 A9 Xout Xin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 - TSOP II (x8) Top View (not to scale) 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 HSB NC A19 A18 A17 A16 A15 OE DQ7 DQ6 VSS VCC DQ5 DQ4 VCAP A14 A13 A12 A11 A10 VRTCcap VRTCbat INT [4] NC A0 A1 A2 A3 A4 CE DQ0 DQ1 DQ2 DQ3 VCC VSS DQ4 DQ5 DQ6 DQ7 WE A5 A6 A7 A8 A9 NC Xout Xin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 54 53 52 51 50 49 54 - TSOP II (x16) Top View (not to scale) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 HSB A18 A17 A16 A15 OE BHE BLE DQ15 DQ14 DQ13 DQ12 VSS VCC DQ11 DQ10 DQ9 DQ8 VCAP A14 A13 A12 A11 A10 NC VRTCcap VRTCbat Table 1. Pin Definitions Pin Name I/O Type Description A0 - A19 Input Address Inputs Used to Select one of the 1,048,576 bytes of the nvSRAM for x8 Configuration. A0 - A18 DQ0 - DQ7 Address Inputs Used to Select one of the 524,288 words of the nvSRAM for x16 Configuration. Input/Output Bidirectional Data I/O Lines for x8 Configuration. Used as input or output lines depending on operation. Bidirectional Data I/O Lines for x16 Configuration. Used as input or output lines depending on operation. DQ0 - DQ15 NC No Connect No Connects. This pin is not connected to the die. Input Write Enable Input, Active LOW. When selected LOW, data on the I/O pins is written to the specific address location. Input Chip Enable Input, Active LOW. When LOW, selects the chip. When HIGH, deselects the chip. Input Output Enable, Active LOW. The active LOW OE input enables the data output buffers during read cycles. Deasserting OE HIGH causes the I/O pins to tristate. BHE Input Byte High Enable, Active LOW. Controls DQ15 - DQ8. BLE Xout Input Byte Low Enable, Active LOW. Controls DQ7 - DQ0. WE CE OE Xin Output Input Crystal Connection. Drives crystal on start up. Crystal Connection. For 32.768 KHz crystal. VRTCcap Power Supply Capacitor Supplied Backup RTC Supply Voltage. Left unconnected if VRTCbat is used. VRTCbat Power Supply Battery Supplied Backup RTC Supply Voltage. Left unconnected if VRTCcap is used. INT Output Interrupt Output. Programmable to respond to the clock alarm, the watchdog timer, and the power monitor. Also programmable to either active HIGH (push or pull) or LOW (open drain). VSS Ground Ground for the Device. Must be connected to ground of the system. Note 4. Address expansion for 16 Mbit. NC pin not connected to die. Document #: 001-47378 Rev. *D Page 3 of 31 [+] Feedback CY14B108K, CY14B108M Table 1. Pin Definitions (continued) Pin Name VCC HSB VCAP I/O Type Description Power Supply Power Supply Inputs to the Device. 3.0V +20%, -10%. Input/Output Hardware STORE Busy (HSB). When LOW this output indicates that a Hardware STORE is in progress. When pulled LOW external to the chip it initiates a nonvolatile STORE operation. A weak internal pull up resistor keeps this pin HIGH if not connected (connection optional). After each STORE operation HSB is driven HIGH for short time with standard output high current. Power Supply AutoStore Capacitor. Supplies power to the nvSRAM during power loss to store data from SRAM to nonvolatile elements. Device Operation AutoStore Operation The CY14B108K/CY14B108M nvSRAM is made up of two functional components paired in the same physical cell. These are a SRAM memory cell and a nonvolatile QuantumTrap cell. The SRAM memory cell operates as a standard fast static RAM. Data in the SRAM is transferred to the nonvolatile cell (the STORE operation), or from the nonvolatile cell to the SRAM (the RECALL operation). Using this unique architecture, all cells are stored and recalled in parallel. During the STORE and RECALL operations SRAM read and write operations are inhibited. The CY14B108K/CY14B108M supports infinite reads and writes similar to a typical SRAM. In addition, it provides infinite RECALL operations from the nonvolatile cells and up to 1 million STORE operations. See the Truth Table For SRAM Operations on page 25 for a complete description of read and write modes. The CY14B108K/CY14B108M stores data to the nvSRAM using one of three storage operations. These three operations are: Hardware STORE, activated by the HSB; Software STORE, activated by an address sequence; AutoStore, on device power down. The AutoStore operation is a unique feature of QuantumTrap technology and is enabled by default on the CY14B108K/CY14B108M. The CY14B108K/CY14B108M performs a read cycle whenever CE and OE are LOW, and WE and HSB are HIGH. The address specified on pins A0-19 or A0-18 determines which of the 1,048,576 data bytes or 524,288 words of 16 bits each are accessed. Byte enables (BHE, BLE) determine which bytes are enabled to the output, in the case of 16-bit words. When the read is initiated by an address transition, the outputs are valid after a delay of tAA (read cycle 1). If the read is initiated by CE or OE, the outputs are valid at tACE or at tDOE, whichever is later (read cycle 2). The data output repeatedly responds to address changes within the tAA access time without the need for transitions on any control input pins. This remains valid until another address change or until CE or OE is brought HIGH, or WE or HSB is brought LOW. Note If the capacitor is not connected to VCAP pin, AutoStore must be disabled using the soft sequence specified in Preventing AutoStore on page 6. In case AutoStore is enabled without a capacitor on VCAP pin, the device attempts an AutoStore operation without sufficient charge to complete the Store. This may corrupt the data stored in nvSRAM. Figure 2. AutoStore Mode VCC 0.1uF VCC 10kOhm SRAM Read During normal operation, the device draws current from VCC to charge a capacitor connected to the VCAP pin. This stored charge is used by the chip to perform a single STORE operation. If the voltage on the VCC pin drops below VSWITCH, the part automatically disconnects the VCAP pin from VCC. A STORE operation is initiated with power provided by the VCAP capacitor. WE VCAP SRAM Write A write cycle is performed when CE and WE are LOW and HSB is HIGH. The address inputs must be stable before entering the write cycle and must remain stable until CE or WE goes HIGH at the end of the cycle. The data on the common I/O pins DO0-15 are written into the memory if it is valid tSD before the end of a WE controlled write or before the end of a CE controlled write. The Byte Enable inputs (BHE, BLE) determine which bytes are written, in the case of 16-bit words. Keep OE HIGH during the entire write cycle to avoid data bus contention on common I/O lines. If OE is left LOW, internal circuitry turns off the output buffers tHZWE after WE goes LOW. Document #: 001-47378 Rev. *D VSS VCAP Figure 2 shows the proper connection of the storage capacitor (VCAP) for automatic STORE operation. Refer to DC Electrical Characteristics on page 16 for the size of the VCAP. The voltage on the VCAP pin is driven to VCC by a regulator on the chip. A pull up should be placed on WE to hold it inactive during power up. This pull up is only effective if the WE signal is tristate during power up. Many MPUs tristate their controls on power up. Verify this when using the pull up. When the nvSRAM comes out of power-on-recall, the MPU must be active or the WE held inactive until the MPU comes out of reset. Page 4 of 31 [+] Feedback CY14B108K, CY14B108M To reduce unnecessary nonvolatile STOREs, AutoStore, and Hardware STORE operations are ignored unless at least one write operation has taken place since the most recent STORE or RECALL cycle. Software initiated STORE cycles are performed regardless of whether a write operation has taken place. The HSB signal is monitored by the system to detect if an AutoStore cycle is in progress. Hardware STORE (HSB) Operation The CY14B108K/CY14B108M provides the HSB pin to control and acknowledge the STORE operations. The HSB pin is used to request a Hardware STORE cycle. When the HSB pin is driven LOW, the CY14B108K/CY14B108M conditionally initiates a STORE operation after tDELAY. An actual STORE cycle begins only if a write to the SRAM has taken place since the last STORE or RECALL cycle. The HSB pin also acts as an open drain driver that is internally driven LOW to indicate a busy condition when the STORE (initiated by any means) is in progress. exact order. During the STORE cycle, an erase of the previous nonvolatile data is first performed, followed by a program of the nonvolatile elements. After a STORE cycle is initiated, further input and output are disabled until the cycle is completed. Because a sequence of reads from specific addresses is used for STORE initiation, it is important that no other read or write accesses intervene in the sequence, or the sequence is aborted and no STORE or RECALL takes place. To initiate the Software STORE cycle, the following read sequence must be performed: 1. Read address 0x4E38 Valid READ 2. Read address 0xB1C7 Valid READ 3. Read address 0x83E0 Valid READ 4. Read address 0x7C1F Valid READ 5. Read address 0x703F Valid READ 6. Read address 0x8FC0 Initiate STORE cycle SRAM write operations that are in progress when HSB is driven LOW by any means are given time (tDELAY) to complete before the STORE operation is initiated. However, any SRAM write cycles requested after HSB goes LOW are inhibited until HSB returns HIGH. In case the write latch is not set, HSB is not driven LOW by the CY14B108K/CY14B108M. But any SRAM read and write cycles are inhibited until HSB is returned HIGH by MPU or other external source. The software sequence may be clocked with CE controlled reads or OE controlled reads, with WE kept HIGH for all the six READ sequences. After the sixth address in the sequence is entered, the STORE cycle commences and the chip is disabled. HSB is driven LOW. After the tSTORE cycle time is fulfilled, the SRAM is activated again for the read and write operation. During any STORE operation, regardless of how it is initiated, the CY14B108K/CY14B108M continues to drive the HSB pin LOW, releasing it only when the STORE is complete. Upon completion of the STORE operation, the CY14B108K/CY14B108M remains disabled until the HSB pin returns HIGH. Leave the HSB unconnected if it is not used. Data is transferred from the nonvolatile memory to the SRAM by a software address sequence. A software RECALL cycle is initiated with a sequence of read operations in a manner similar to the Software STORE initiation. To initiate the RECALL cycle, perform the following sequence of CE or OE controlled read operations: 1. Read address 0x4E38 Valid READ 2. Read address 0xB1C7 Valid READ 3. Read address 0x83E0 Valid READ 4. Read address 0x7C1F Valid READ 5. Read address 0x703F Valid READ 6. Read address 0x4C63 Initiate RECALL cycle Hardware RECALL (Power Up) During power up or after any low power condition (VCC< VSWITCH), an internal RECALL request is latched. When VCC again exceeds the VSWITCH on powerup, a RECALL cycle is automatically initiated and takes tHRECALL to complete. During this time, the HSB pin is driven LOW by the HSB driver and all reads and writes to nvSRAM are inhibited. Software STORE Data is transferred from the SRAM to the nonvolatile memory by a software address sequence. The CY14B108K/CY14B108M Software STORE cycle is initiated by executing sequential CE or OE controlled read cycles from six specific address locations in Document #: 001-47378 Rev. *D Software RECALL Internally, RECALL is a two step procedure. First, the SRAM data is cleared; then, the nonvolatile information is transferred into the SRAM cells. After the tRECALL cycle time, the SRAM is again ready for read and write operations. The RECALL operation does not alter the data in the nonvolatile elements. Page 5 of 31 [+] Feedback CY14B108K, CY14B108M Table 2. Mode Selection OE, BHE, BLE[3] X A15 - A0[5] X Mode I/O Power Not Selected Output High Z Standby H L X Read SRAM Output Data Active L X X Write SRAM Input Data Active L H L 0x4E38 0xB1C7 0x83E0 0x7C1F 0x703F 0x8B45 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM AutoStore Disable Output Data Output Data Output Data Output Data Output Data Output Data Active[6] L H L 0x4E38 0xB1C7 0x83E0 0x7C1F 0x703F 0x4B46 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM AutoStore Enable Output Data Output Data Output Data Output Data Output Data Output Data Active[6] L H L 0x4E38 0xB1C7 0x83E0 0x7C1F 0x703F 0x8FC0 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Nonvolatile STORE Output Data Output Data Output Data Output Data Output Data Output High Z Active ICC2[6] L H L 0x4E38 0xB1C7 0x83E0 0x7C1F 0x703F 0x4C63 Read SRAM Read SRAM Read SRAM Read SRAM Read SRAM Nonvolatile RECALL Output Data Output Data Output Data Output Data Output Data Output High Z Active[6] CE H WE X L L Preventing AutoStore The AutoStore function is disabled by initiating an AutoStore disable sequence. A sequence of read operations is performed in a manner similar to the Software STORE initiation. To initiate the AutoStore disable sequence, the following sequence of CE or OE controlled read operations must be performed: 1. Read address 0x4E38 Valid READ 2. Read address 0xB1C7 Valid READ 3. Read address 0x83E0 Valid READ 4. Read address 0x7C1F Valid READ 5. Read address 0x703F Valid READ 6. Read address 0x8B45 AutoStore Disable AutoStore is re-enabled by initiating an AutoStore enable sequence. A sequence of read operations is performed in a manner similar to the software RECALL initiation. To initiate the AutoStore enable sequence, the following sequence of CE or OE controlled read operations must be performed: 1. Read address 0x4E38 Valid READ 2. Read address 0xB1C7 Valid READ 3. Read address 0x83E0 Valid READ 4. Read address 0x7C1F Valid READ 5. Read address 0x703F Valid READ 6. Read address 0x4B46 AutoStore Enable If the AutoStore function is disabled or re-enabled, a manual STORE operation (hardware or software) issued to save the AutoStore state through subsequent power down cycles. The part comes from the factory with AutoStore enabled. Notes 5. While there are 20 address lines on the CY14B108K (19 address lines on the CY14B108M), only the 13 address lines (A14 - A2) are used to control software modes. The remaining address lines are don't care. 6. The six consecutive address locations must be in the order listed. WE must be HIGH during all six cycles to enable a nonvolatile cycle. Document #: 001-47378 Rev. *D Page 6 of 31 [+] Feedback CY14B108K, CY14B108M Data Protection The CY14B108K/CY14B108M protects data from corruption during low voltage conditions by inhibiting all externally initiated STORE and write operations. The low voltage condition is detected when VCC is less than VSWITCH. If the CY14B108K/CY14B108M is in a write mode (both CE and WE are LOW) at power up, after a RECALL or STORE, the write is inhibited until the SRAM is enabled after tLZHSB (HSB to output active). This protects against inadvertent writes during power up or brown out conditions. Noise Considerations Refer to CY application note AN1064. Power up boot firmware routines should rewrite the nvSRAM into the desired state (for example, autostore enabled). While the nvSRAM is shipped in a preset state, best practice is to again rewrite the nvSRAM into the desired state as a safeguard against events that might flip the bit inadvertently such as program bugs and incoming inspection routines. The VCAP value specified in this data sheet includes a minimum and a maximum value size. Best practice is to meet this requirement and not exceed the maximum VCAP value because the nvSRAM internal algorithm calculates VCAP charge and discharge time based on this maximum VCAP value. Customers that want to use a larger VCAP value to make sure there is extra store charge and store time should discuss their VCAP size selection with Cypress to understand any impact on the VCAP voltage level at the end of a tRECALL period. Best Practices nvSRAM products have been used effectively for over 15 years. While ease-of-use is one of the product's main system values, experience gained working with hundreds of applications has resulted in the following suggestions as best practices: The nonvolatile cells in this nvSRAM product are delivered from Cypress with 0x00 written in all cells. Incoming inspection routines at customer or contract manufacturer's sites sometimes reprogram these values. Final NV patterns are typically repeating patterns of AA, 55, 00, FF, A5, or 5A. End product's firmware should not assume an NV array is in a set programmed state. Routines that check memory content values to determine first time system configuration, cold or warm boot status, and so on should always program a unique NV pattern (that is, complex 4-byte pattern of 46 E6 49 53 hex or more random bytes) as part of the final system manufacturing test to ensure these system routines work consistently. Document #: 001-47378 Rev. *D Page 7 of 31 [+] Feedback CY14B108K, CY14B108M Real Time Clock Operation nvTime Operation The CY14B108K/CY14B108M offers internal registers that contain clock, alarm, watchdog, interrupt, and control functions. RTC registers use the last 16 address locations of the SRAM. Internal double buffering of the clock and timer information registers prevents accessing transitional internal clock data during a read or write operation. Double buffering also circumvents disrupting normal timing counts or the clock accuracy of the internal clock when accessing clock data. Clock and alarm registers store data in BCD format. RTC functionality is described with respect to CY14B108K in the following sections. The same description applies to CY14B108M, except for the RTC register addresses. The RTC register addresses for CY14B108K range from 0xFFFF0 to 0xFFFFF, while those for CY14B108M range from 0x7FFF0 to 0x7FFFF. Refer to Table 4 on page 12 and Table 5 on page 13 for a detailed Register Map description. Clock Operations The clock registers maintain time up to 9,999 years in one second increments. The time can be set to any calendar time and the clock automatically keeps track of days of the week and month, leap years, and century transitions. There are eight registers dedicated to the clock functions, which are used to set time with a write cycle and to read time during a read cycle. These registers contain the time of day in BCD format. Bits defined as `0' are currently not used and are reserved for future use by Cypress. Reading the Clock The double buffered RTC register structure reduces the chance of reading incorrect data from the clock. The user must stop internal updates to the CY14B108K time keeping registers before reading clock data, to prevent reading of data in transition. Stopping the register updates does not affect clock accuracy. The updating process is stopped by writing a `1' to the read bit `R' (in the flags register at 0xFFFF0), and does not restart until a `0' is written to the read bit. The RTC registers are then read while the internal clock continues to run. After a `0' is written to the read bit (`R'), all RTC registers are simultaneously updated within 20 ms Setting the Clock Setting the write bit `W' (in the flags register at 0xFFFF0) to a `1' stops updates to the time keeping registers and enables the time to be set. The correct day, date, and time is then written into the registers and must be in 24 hour BCD format. The time written is referred to as the "Base Time". This value is stored in nonvolatile registers and used in the calculation of the current time. Resetting the write bit to `0' transfers the values of timekeeping registers to the actual clock counters, after which the clock resumes normal operation. If the time written to the timekeeping registers is not in the correct BCD format, each invalid nibble of the RTC registers continue counting to 0xF before rolling over to 0x0 after which RTC resumes normal operation. Note The values entered in the timekeeping, alarm, calibration, and interrupt registers need a STORE operation to be saved in nonvolatile memory. Therefore, while working in AutoStore Document #: 001-47378 Rev. *D disabled mode, the user must perform a STORE operation after writing into the RTC registers for the RTC to work correctly. Backup Power The RTC in the CY14B108K is intended for permanently powered operation. The VRTCcap or VRTCbat pin is connected depending on whether a capacitor or battery is chosen for the application. When the primary power, VCC, fails and drops below VSWITCH the device switches to the backup power supply. The clock oscillator uses very little current, which maximizes the backup time available from the backup source. Regardless of the clock operation with the primary source removed, the data stored in the nvSRAM is secure, having been stored in the nonvolatile elements when power was lost. During backup operation, the CY14B108K consumes 0.35 microamps (Typ) at room temperature. User must choose capacitor or battery values according to the application. Backup time values based on maximum current specifications are shown in the following table. Nominal backup times are approximately two times longer. Table 3. RTC Backup Time Capacitor Value 0.1F 0.47F 1.0F Backup Time 72 hours 14 days 30 days Using a capacitor has the obvious advantage of recharging the backup source each time the system is powered up. If a battery is used, a 3V lithium is recommended and the CY14B108K sources current only from the battery when the primary power is removed. However, the battery is not recharged at any time by the CY14B108K. The battery capacity must be chosen for total anticipated cumulative down time required over the life of the system. Stopping and Starting the Oscillator The OSCEN bit in the calibration register at 0xFFFF8 controls the enable and disable of the oscillator. This bit is nonvolatile and is shipped to customers in the "enabled" (set to 0) state. To preserve the battery life when the system is in storage, OSCEN must be set to `1'. This turns off the oscillator circuit, extending the battery life. If the OSCEN bit goes from disabled to enabled, it takes approximately one second (two seconds maximum) for the oscillator to start. While system power is off, If the voltage on the backup supply (VRTCcap or VRTCbat) falls below their respective minimum level, the oscillator may fail.The CY14B108K has the ability to detect oscillator failure when system power is restored. This is recorded in the OSCF (Oscillator Failed bit) of the flags register at the address 0xFFFF0. When the device is powered on (VCC goes above VSWITCH) the OSCEN bit is checked for "enabled" status. If the OSCEN bit is enabled and the oscillator is not active within the first 5 ms, the OSCF bit is set to "1". The system must check for this condition and then write `0' to clear the flag. Note that in addition to setting the OSCF flag bit, the time registers are reset to the "Base Time" (see Setting the Clock on page 8), which is the value last written to the timekeeping registers. The control or calibration registers and the OSCEN bit are not affected by the `oscillator failed' condition. Page 8 of 31 [+] Feedback CY14B108K, CY14B108M The value of OSCF must be reset to `0' when the time registers are written for the first time. This initializes the state of this bit which may have become set when the system was first powered on. To reset OSCF, set the write bit "W" (in the Flags register at 0xFFFF0) to a "1" to enable writes to the Flag register. Write a "0" to the OSCF bit and then reset the write bit to "0" to disable writes. Calibrating the Clock The RTC is driven by a quartz controlled crystal with a nominal frequency of 32.768 kHz. Clock accuracy depends on the quality of the crystal and calibration. The crystals available in market typically have an error of +20 ppm to +35 ppm. However, CY14B108K employs a calibration circuit that improves the accuracy to +1/-2 ppm at 25C. This implies an error of +2.5 seconds to -5 seconds per month. The calibration circuit adds or subtracts counts from the oscillator divider circuit to achieve this accuracy. The number of pulses that are suppressed (subtracted, negative calibration) or split (added, positive calibration) depends upon the value loaded into the five calibration bits found in Calibration register at 0xFFFF8. The calibration bits occupy the five lower order bits in the Calibration register. These bits are set to represent any value between `0' and 31 in binary form. Bit D5 is a sign bit, where a `1' indicates positive calibration and a `0' indicates negative calibration. Adding counts speeds the clock up and subtracting counts slows the clock down. If a binary `1' is loaded into the register, it corresponds to an adjustment of 4.068 or -2.034 ppm offset in oscillator error, depending on the sign. Calibration occurs within a 64-minute cycle. The first 62 minutes in the cycle may, once every minute, have one second shortened by 128 or lengthened by 256 oscillator cycles. If a binary `1' is loaded into the register, only the first two minutes of the 64-minute cycle are modified. If a binary 6 is loaded, the first 12 are affected, and so on. Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator cycles for every 125,829,120 actual oscillator cycles, that is, 4.068 or -2.034 ppm of adjustment per calibration step in the Calibration register. To determine the required calibration, the CAL bit in the Flags register (0xFFFF0) must be set to `1'. This causes the INT pin to toggle at a nominal frequency of 512 Hz. Any deviation measured from the 512 Hz indicates the degree and direction of the required correction. For example, a reading of 512.01024 Hz indicates a +20 ppm error. Hence, a decimal value of -10 (001010b) must be loaded into the Calibration register to offset this error. Note Setting or changing the Calibration register does not affect the test output frequency. To set or clear CAL, set the write bit "W" (in the flags register at 0xFFFF0) to "1" to enable writes to the Flag register. Write a value to CAL, and then reset the write bit to "0" to disable writes. Alarm The alarm function compares user programmed values of alarm time and date (stored in the registers 0xFFFF1-5) with the corresponding time of day and date values. When a match occurs, the Document #: 001-47378 Rev. *D alarm internal flag (AF) is set and an interrupt is generated on INT pin if Alarm Interrupt Enable (AIE) bit is set. There are four alarm match fields - date, hours, minutes, and seconds. Each of these fields has a match bit that is used to determine if the field is used in the alarm match logic. Setting the match bit to `0' indicates that the corresponding field is used in the match process. Depending on the match bits, the alarm occurs as specifically as once a month or as frequently as once every minute. Selecting none of the match bits (all 1s) indicates that no match is required and therefore, alarm is disabled. Selecting all match bits (all 0s) causes an exact time and date match. There are two ways to detect an alarm event: by reading the AF flag or monitoring the INT pin. The AF flag in the flags register at 0xFFFF0 indicates that a date or time match has occurred. The AF bit is set to "1" when a match occurs. Reading the flags register clears the alarm flag bit (and all others). A hardware interrupt pin may also be used to detect an alarm event. To set, clear or enable an alarm, set the `W' bit (in Flags Register - 0xFFFF0) to `1' to enable writes to Alarm Registers. After writing the alarm value, clear the `W' bit back to "0" for the changes to take effect. Note CY14B108K requires the alarm match bit for seconds (0xFFFF2 - D7) to be set to `0' for proper operation of Alarm Flag and Interrupt. Watchdog Timer The Watchdog Timer is a free running down counter that uses the 32 Hz clock (31.25 ms) derived from the crystal oscillator. The oscillator must be running for the watchdog to function. It begins counting down from the value loaded in the Watchdog Timer register. The timer consists of a loadable register and a free running counter. On power up, the watchdog time out value in register 0xFFFF7 is loaded into the Counter Load register. Counting begins on power up and restarts from the loadable value any time the Watchdog Strobe (WDS) bit is set to `1'. The counter is compared to the terminal value of `0'. If the counter reaches this value, it causes an internal flag and an optional interrupt output. You can prevent the time out interrupt by setting WDS bit to `1' prior to the counter reaching `0'. This causes the counter to reload with the watchdog time out value and to be restarted. As long as the user sets the WDS bit prior to the counter reaching the terminal value, the interrupt and WDT flag never occur. New time out values are written by setting the watchdog write bit to `0'. When the WDW is `0', new writes to the watchdog time out value bits D5-D0 are enabled to modify the time out value. When WDW is `1', writes to bits D5-D0 are ignored. The WDW function enables a user to set the WDS bit without concern that the watchdog timer value is modified. A logical diagram of the watchdog timer is shown in Figure 3. Note that setting the watchdog time out value to `0' disables the watchdog function. The output of the watchdog timer is the flag bit WDF that is set if the watchdog is allowed to time out. If the Watchdog Interrupt Enable (WIE) bit in the Interrupt register is set, a hardware interrupt on INT pin is also generated on watchdog timeout. The flag and the hardware interrupt are both cleared when user reads the Flags registers. Page 9 of 31 [+] Feedback CY14B108K, CY14B108M Figure 3. Watchdog Timer Block Diagram Clock Divider Oscillator 32,768 KHz 1 Hz 32 Hz Counter Zero Compare WDF Load Register WDS Q D Interrupts are only generated while working on normal power and are not triggered when system is running in backup power mode. Note CY14B108K generates valid interrupts only after the Powerup Recall sequence is completed. All events on INT pin must be ignored for tHRECALL duration after powerup. Interrupt Register WDW Q write to Watchdog Register output from the INT pin. In pulse mode, the pulse width is internally fixed at approximately 200 ms. This mode is intended to reset a host microcontroller. In the level mode, the pin goes to its active polarity until the Flags register is read by the user. This mode is used as an interrupt to a host microcontroller. The control bits are summarized in the following section. Watchdog Register . Power Monitor The CY14B108K provides a power management scheme with power fail interrupt capability. It also controls the internal switch to backup power for the clock and protects the memory from low VCC access. The power monitor is based on an internal band gap reference circuit that compares the VCC voltage to VSWITCH threshold. As described in the section AutoStore Operation on page 4, when VSWITCH is reached as VCC decays from power loss, a data STORE operation is initiated from SRAM to the nonvolatile elements, securing the last SRAM data state. Power is also switched from VCC to the backup supply (battery or capacitor) to operate the RTC oscillator. When operating from the backup source, read and write operations to nvSRAM are inhibited and the clock functions are not available to the user. The clock continues to operate in the background. The updated clock data is available to the user tHRECALL delay after VCC is restored to the device (see AutoStore/Power Up RECALL on page 22) Interrupts The CY14B108K has Flags register, Interrupt register, and Interrupt logic that can signal interrupt to the microcontroller. There are three potential sources for interrupt: watchdog timer, power monitor, and alarm timer. Each of these can be individually enabled to drive the INT pin by appropriate setting in the Interrupt register (0xFFFF6). In addition, each has an associated flag bit in the Flags register (0xFFFF0) that the host processor uses to determine the cause of the interrupt. The INT pin driver has two bits that specify its behavior when an interrupt occurs. An Interrupt is raised only if both a flag is raised by one of the three sources and the respective interrupt enable bit in Interrupts register is enabled (set to `1'). After an interrupt source is active, two programmable bits, H/L and P/L, determine the behavior of the output pin driver on INT pin. These two bits are located in the Interrupt register and can be used to drive level or pulse mode Document #: 001-47378 Rev. *D Watchdog Interrupt Enable (WIE). When set to `1', the watchdog timer drives the INT pin and an internal flag when a watchdog time out occurs. When WIE is set to `0', the watchdog timer only affects the WDF flag in Flags register. Alarm Interrupt Enable (AIE). When set to `1', the alarm match drives the INT pin and an internal flag. When AIE is set to `0', the alarm match only affects the AF Flags register. Power Fail Interrupt Enable (PFE). When set to `1', the power fail monitor drives the pin and an internal flag. When PFE is set to `0', the power fail monitor only affects the PF flag in Flags register. High/Low (H/L). When set to a `1', the INT pin is active HIGH and the driver mode is push pull. The INT pin drives high only when VCC is greater than VSWITCH. When set to a `0', the INT pin is active LOW and the drive mode is open drain. The INT pin must be pulled up to Vcc by a 10k resistor while using the interrupt in active LOW mode. Pulse/Level (P/L). When set to a `1' and an interrupt occurs, the INT pin is driven for approximately 200 ms. When P/L is set to a `0', the INT pin is driven high or low (determined by H/L) until the Flags or Control register is read. When an enabled interrupt source activates the INT pin, an external host reads the Flags registers to determine the cause. Remember that all flags are cleared when the register is read. If the INT pin is programmed for Level mode, then the condition clears and the INT pin returns to its inactive state. If the pin is programmed for Pulse mode, then reading the flag also clears the flag and the pin. The pulse does not complete its specified duration if the Flags register is read. If the INT pin is used as a host reset, the Flags register is not read during a reset Flags Register The Flag register has three flag bits: WDF, AF, and PF, which can be used to generate an interrupt. They are set by the watchdog timeout, alarm match, or power fail monitor respectively. The processor can either poll this register or enable interrupts when a flag is set. These flags are automatically reset when the register is read. The flags register is automatically loaded with the value 0x00 on power up (except for the OSCF bit. See Stopping and Starting the Oscillator on page 8) Page 10 of 31 [+] Feedback CY14B108K, CY14B108M Figure 4. RTC Recommended Component Configuration Recommended Values Y1 = 32.768 KHz (12.5 pF) C1 = 12 pF C2 = 69 pF Note: The recommended values for C1 and C2 include board trace capacitance. C1 Y1 C2 Xout Xin Figure 5. Interrupt Block Diagram WDF Watchdog Timer WIE PF Power Monitor PFE P/L VCC Pin Driver INT VINT H/L VSS WDF - Watchdog Timer Flag WIE - Watchdog Interrupt Enable PF - Power Fail Flag PFE - Power Fail Enable AF - Alarm Flag AIE - Alarm Interrupt Enable P/L - Pulse Level H/L - High/Low AF Clock Alarm AIE Document #: 001-47378 Rev. *D Page 11 of 31 [+] Feedback CY14B108K, CY14B108M Table 4. RTC Register Map[7] BCD Format Data[8] Register CY14B108K CY14B108M D7 D6 0xFFFFF 0x7FFFF 0xFFFFE 0x7FFFE 0 0 0xFFFFD 0x7FFFD 0 0 0xFFFFC 0x7FFFC 0 0 0xFFFFB 0x7FFFB 0 0 0xFFFFA 0x7FFFA 0 D5 D4 D3 10s Years 0 10s Months 10s Day of Month 0 0 D2 10s Hours Function/Range Years: 00-99 Months Months: 01-12 Day Of Month Day of Month: 01-31 Day of week Day of week: 01-07 Hours Hours: 00-23 Minutes Minutes: 00-59 0xFFFF9 0x7FFF9 0 0xFFFF8 0x7FFF8 OSCEN (0) 0 0xFFFF7 0x7FFF7 WDS (0) WDW (0) 0xFFFF6 0x7FFF6 WIE (0) AIE (0) 0xFFFF5 0x7FFF5 M (1) 0 10s Alarm Date Alarm Day Alarm, Day of Month: 01-31 0xFFFF4 0x7FFF4 M (1) 0 10s Alarm Hours Alarm Hours Alarm, Hours: 00-23 0xFFFF3 0x7FFF3 M (1) 10 Alarm Minutes Alarm Minutes Alarm, Minutes: 00-59 0xFFFF2 0x7FFF2 M (1) 10 Alarm Seconds Alarm, Seconds Alarm, Seconds: 00-59 0xFFFF1 0x7FFF1 0xFFFF0 0x7FFF0 10s Seconds D0 Years 0 10s Minutes D1 Seconds Cal Sign (0) AF Watchdog [9] WDT (000000) PFE (0) 0 H/L (1) 10s Centuries WDF Seconds: 00-59 Calibration Values [9] Calibration (00000) PF P/L (0) 0 0 Centuries OSCF 0 CAL (0) W (0) Interrupts [9] Centuries: 00-99 R (0) Flags [9] Notes 7. Upper Byte D15-D8 (CY14B108M) of RTC registers are reserved for future use 8. ( ) designates values shipped from the factory. 9. This is a binary value, not a BCD value. Document #: 001-47378 Rev. *D Page 12 of 31 [+] Feedback CY14B108K, CY14B108M Table 5. Register Map Detail Register CY14B108K CY14B108M 0xFFFFF 0x7FFFF Description Time Keeping - Years D7 D6 D5 D4 D3 D2 10s Years D1 D0 Years Contains the lower two BCD digits of the year. Lower nibble (four bits) contains the value for years; upper nibble (four bits) contains the value for 10s of years. Each nibble operates from 0 to 9. The range for the register is 0-99. 0xFFFFE 0x7FFFE Time Keeping - Months D7 D6 D5 D4 0 0 0 10s Month D3 D2 D1 D0 Months Contains the BCD digits of the month. Lower nibble (four bits) contains the lower digit and operates from 0 to 9; upper nibble (one bit) contains the upper digit and operates from 0 to 1. The range for the register is 1-12. 0xFFFFD 0x7FFFD Time Keeping - Date D7 D6 0 0 D5 D4 D3 10s Day of Month D2 D1 D0 Day of Month Contains the BCD digits for the date of the month. Lower nibble (four bits) contains the lower digit and operates from 0 to 9; upper nibble (two bits) contains the 10s digit and operates from 0 to 3. The range for the register is 1-31. Leap years are automatically adjusted for. 0xFFFFC 0x7FFFC Time Keeping - Day D7 D6 D5 D4 D3 0 0 0 0 0 D2 D1 D0 Day of Week Lower nibble (three bits) contains a value that correlates to day of the week. Day of the week is a ring counter that counts from 1 to 7 then returns to 1. The user must assign meaning to the day value, because the day is not integrated with the date. 0xFFFFB 0x7FFFB Time Keeping - Hours D7 D6 0 0 D5 D4 D3 D2 10s Hours D1 D0 Hours Contains the BCD value of hours in 24 hour format. Lower nibble (four bits) contains the lower digit and operates from 0 to 9; upper nibble (two bits) contains the upper digit and operates from 0 to 2. The range for the register is 0-23. 0xFFFFA 0x7FFFA Time Keeping - Minutes D7 D6 0 D5 D4 D3 D2 10s Minutes D1 D0 Minutes Contains the BCD value of minutes. Lower nibble (four bits) contains the lower digit and operates from 0 to 9; upper nibble (three bits) contains the upper minutes digit and operates from 0 to 5. The range for the register is 0-59. 0xFFFF9 0x7FFF9 Time Keeping - Seconds D7 0 D6 D5 10s Seconds D4 D3 D2 D1 D0 Seconds Contains the BCD value of seconds. Lower nibble (four bits) contains the lower digit and operates from 0 to 9; upper nibble (three bits) contains the upper digit and operates from 0 to 5. The range for the register is 0 to 59. Document #: 001-47378 Rev. *D Page 13 of 31 [+] Feedback CY14B108K, CY14B108M Table 5. Register Map Detail (continued) Register CY14B108K CY14B108M 0xFFFF8 0x7FFF8 OSCEN Description Calibration/Control D7 D6 D5 OSCEN 0 Calibration Sign D4 D3 D2 D1 D0 Calibration Oscillator Enable. When set to 1, the oscillator is stopped. When set to 0, the oscillator runs. Disabling the oscillator saves battery or capacitor power during storage. Calibration Sign Determines if the calibration adjustment is applied as an addition (1) to or as a subtraction (0) from the time-base. Calibration These five bits control the calibration of the clock. 0xFFFF7 0x7FFF7 WatchDog Timer D7 D6 WDS WDW D5 D4 D3 D2 D1 D0 WDT WDS Watchdog Strobe. Setting this bit to 1 reloads and restarts the watchdog timer. Setting the bit to 0 has no effect. The bit is cleared automatically after the watchdog timer is reset. The WDS bit is write only. Reading it always returns a 0. WDW Watchdog Write Enable. Setting this bit to 1 disables any WRITE to the watchdog timeout value (D5-D0). This allows the user to set the watchdog strobe bit without disturbing the timeout value. Setting this bit to 0 allows bits D5-D0 to be written to the watchdog register when the next write cycle is complete. This function is explained in more detail in Watchdog Timer on page 9. WDT Watchdog timeout selection. The watchdog timer interval is selected by the 6-bit value in this register. It represents a multiplier of the 32 Hz count (31.25 ms). The range of timeout value is 31.25 ms (a setting of 1) to 2 seconds (setting of 3 Fh). Setting the watchdog timer register to 0 disables the timer. These bits can be written only if the WDW bit was set to 0 on a previous cycle. 0xFFFF6 0x7FFF6 Interrupt Status/Control D7 D6 D5 D4 D3 D2 D1 D0 WIE AIE PFE 0 H/L P/L 0 0 WIE Watchdog Interrupt Enable. When set to 1 and a watchdog timeout occurs, the watchdog timer drives the INT pin and the WDF flag. When set to 0, the watchdog timeout affects only the WDF flag. AIE Alarm Interrupt Enable. When set to 1, the alarm match drives the INT pin and the AF flag. When set to 0, the alarm match only affects the AF flag. PFE Power Fail Enable. When set to 1, the power fail monitor drives the INT pin and the PF flag. When set to 0, the power fail monitor affects only the PF flag. 0 Reserved for future use H/L High/Low. When set to 1, the INT pin is driven active HIGH. When set to 0, the INT pin is open drain, active LOW. P/L Pulse/Level. When set to 1, the INT pin is driven active (determined by H/L) by an interrupt source for approximately 200 ms. When set to 0, the INT pin is driven to an active level (as set by H/L) until the flags register is read. 0xFFFF5 0x7FFF5 Alarm - Day D7 D6 M 0 D5 D4 10s Alarm Date D3 D2 D1 D0 Alarm Date Contains the alarm value for the date of the month and the mask bit to select or deselect the date value. M Document #: 001-47378 Rev. *D Match. When this bit is set to 0, the date value is used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the date value. Page 14 of 31 [+] Feedback CY14B108K, CY14B108M Table 5. Register Map Detail (continued) Register CY14B108K CY14B108M 0xFFFF4 0x7FFF4 Description Alarm - Hours D7 D6 M 0 D5 D4 D3 10s Alarm Hours D2 D1 D0 Alarm Hours Contains the alarm value for the hours and the mask bit to select or deselect the hours value. M 0xFFFF3 Match. When this bit is set to 0, the hours value is used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the hours value. 0x7FFF3 Alarm - Minutes D7 D6 M D5 D4 D3 10s Alarm Minutes D2 D1 D0 Alarm Minutes Contains the alarm value for the minutes and the mask bit to select or deselect the minutes value. M 0xFFFF2 Match. When this bit is set to 0, the minutes value is used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the minutes value. 0x7FFF2 Alarm - Seconds D7 D6 M D5 D4 D3 10s Alarm Seconds D2 D1 D0 Alarm Seconds Contains the alarm value for the seconds and the mask bit to select or deselect the seconds' value. M 0xFFFF1 Match. When this bit is set to 0, the seconds value is used in the alarm match. Setting this bit to 1 causes the match circuit to ignore the seconds value. 0x7FFF1 Time Keeping - Centuries D7 D6 D5 D4 D3 D2 10s Centuries D1 D0 Centuries Contains the BCD value of centuries. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble contains the upper digit and operates from 0 to 9. The range for the register is 0-99 centuries. 0xFFFF0 0x7FFF0 Flags D7 D6 D5 D4 D3 D2 D1 D0 WDF AF PF OSCF 0 CAL W R WDF Watchdog Timer Flag. This read only bit is set to 1 when the watchdog timer is allowed to reach 0 without being reset by the user. It is cleared to 0 when the Flags register is read or on power up AF Alarm Flag. This read only bit is set to 1 when the time and date match the values stored in the alarm registers with the match bits = 0. It is cleared when the Flags register is read or on power up. PF Power Fail Flag. This read only bit is set to 1 when power falls below the power fail threshold VSWITCH. It is cleared to 0 when the Flags register is read or on power up. OSCF Oscillator Fail Flag. Set to 1 on power up if the oscillator is enabled and not running in the first 5 ms of operation. This indicates that RTC backup power failed and clock value is no longer valid. This bit survives power cycle and is never cleared internally by the chip. The user must check for this condition and write '0' to clear this flag. CAL Calibration Mode. When set to 1, a 512 Hz square wave is output on the INT pin. When set to 0, the INT pin resumes normal operation. This bit defaults to 0 (disabled) on power up. W Write Enable: Setting the W bit to 1 freezes updates of the RTC registers. The user can then write to RTC registers, Alarm registers, Calibration register, Interrupt register and Flags register. Setting the W bit to 0 causes the contents of the RTC registers to be transferred to the time keeping counters if the time is changed (a new base time is loaded). This bit defaults to 0 on power up. R Read Enable: Setting R bit to 1, stops clock updates to user RTC registers so that clock updates are not seen during the reading process. Set R bit to 0 to resume clock updates to the holding register. Setting this bit does not require W bit to be set to 1. This bit defaults to 0 on power up. Document #: 001-47378 Rev. *D Page 15 of 31 [+] Feedback CY14B108K, CY14B108M Maximum Ratings Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested. Package Power Dissipation Capability (TA = 25C) ................................................... 1.0W Storage Temperature ................................. -65C to +150C Surface Mount Pb Soldering Temperature (3 Seconds) .......................................... +260C Maximum Accumulated Storage Time At 150C Ambient Temperature................................... 1000h At 85C Ambient Temperature..................... ........... 20 Years Ambient Temperature with Power Applied ............................................ -55C to +150C Supply Voltage on VCC Relative to GND ..........-0.5V to 4.1V Voltage Applied to Outputs in High Z State ....................................... -0.5V to VCC + 0.5V Input Voltage...........................................-0.5V to Vcc + 0.5V DC Output Current (1 output at a time, 1s duration).....15 mA Static Discharge Voltage.......................................... > 2001V (per MIL-STD-883, Method 3015) Latch Up Current ................................................... > 200 mA Operating Range Range Ambient Temperature VCC -40C to +85C 2.7V to 3.6V Industrial Transient Voltage (<20 ns) on Any Pin to Ground Potential .................. -2.0V to VCC + 2.0V DC Electrical Characteristics Over the Operating Range (VCC = 2.7V to 3.6V) Parameter Description Test Conditions Min Typ[10] Max Unit 2.7 3.0 3.6 V VCC Power Supply ICC1 Average VCC Current tRC = 25 ns tRC = 45 ns Values obtained without output loads (IOUT = 0 mA) 75 57 mA mA ICC2 Average VCC Current All Inputs Don't Care, VCC = Max. during STORE Average current for duration tSTORE 20 mA ICC3 Average VCC Current All Inputs Cycling at CMOS Levels. at tRC = 200 ns, Values obtained without output loads (IOUT = 0 mA). VCC (Typ), 25C ICC4 Average VCAP Current during AutoStore Cycle ISB VCC Standby Current CE > (VCC - 0.2V). VIN < 0.2V or > (VCC - 0.2V). W bit set to `0'. Standby current level after nonvolatile cycle is complete. Inputs are static. f = 0 MHz. IIX[11] Input Leakage Current (except HSB) VCC = Max, VSS < VIN < VCC Input Leakage Current (for HSB) VCC = Max, VSS < VIN < VCC IOZ Off State Output Leakage Current VCC = Max, VSS < VOUT < VCC, CE or OE > VIH or BHE/BLE > VIH or WE < VIL 40 All Inputs Don't Care. Average current for duration tSTORE mA 10 mA 10 mA -2 +2 A -200 +2 A -2 +2 A VIH Input HIGH Voltage 2.0 VCC + 0.5 V VIL Input LOW Voltage Vss - 0.5 0.8 V VOH Output HIGH Voltage IOUT = -2 mA VOL Output LOW Voltage IOUT = 4 mA VCAP Storage Capacitor Between VCAP pin and VSS, 5V Rated 2.4 122 V 150 0.4 V 360 F Notes 10. Typical values are at 25C, VCC= VCC (Typ). Not 100% tested. 11. The HSB pin has IOUT = -2 uA for VOH of 2.4V when both active HIGH and LOW drivers are disabled. When they are enabled standard VOH and VOL are valid. This parameter is characterized but not tested. Document #: 001-47378 Rev. *D Page 16 of 31 [+] Feedback CY14B108K, CY14B108M Data Retention and Endurance Parameter Description DATAR Data Retention NVC Nonvolatile STORE Operations Min Unit 20 Years 1,000 K Capacitance In the following table, the capacitance parameters are listed. [12] Parameter Description CIN Input Capacitance COUT Output Capacitance Test Conditions Max Unit 14 pF 14 pF TA = 25C, f = 1 MHz, VCC = VCC (Typ) Thermal Resistance In the following table, the thermal resistance parameters are listed.[12] Parameter Description JA Thermal Resistance (Junction to Ambient) JC Thermal Resistance (Junction to Case) Test Conditions Test conditions follow standard test methods and procedures for measuring thermal impedance, in accordance with EIA/JESD51. 44 TSOP II 54 TSOP II Unit 31.11 30.73 C/W 5.56 6.08 C/W Figure 6. AC Test Loads 577 577 3.0V 3.0V R1 R1 OUTPUT OUTPUT 30 pF R2 789 5 pF R2 789 AC Test Conditions Input Pulse Levels ....................................................0V to 3V Input Rise and Fall Times (10% - 90%) ........................ <3 ns Input and Output Timing Reference Levels .................... 1.5V Note 12. These parameters are only guaranteed by design and are not tested. Document #: 001-47378 Rev. *D Page 17 of 31 [+] Feedback CY14B108K, CY14B108M RTC Characteristics Parameters Description VRTCbat RTC Battery Pin Voltage IBAK[13] RTC Backup Current Min Typ[10] 1.8 3.0 TA (Min) 25C RTC Capacitor Pin Voltage tOCS RTC Oscillator Time to Start RBKCHG RTC Backup Capacitor Charge Current -Limiting Resistor TA (Min) 1.6 25C 1.5 TA (Max) 1.4 3.0 1 350 Units 3.6 V 0.35 A 0.5 A 3.6 V 3.6 V A 0.35 TA (Max) VRTCcap[14] Max 3.6 V 2 sec 850 Notes 13. From either VRTCcap or VRTCbat. 14. If VRTCcap > 0.5V or if no capacitor is connected to VRTCcap pin, the oscillator starts in tOCS time. If a backup capacitor is connected and VRTCcap < 0.5V, the capacitor must be allowed to charge to 0.5V for oscillator to start. Document #: 001-47378 Rev. *D Page 18 of 31 [+] Feedback CY14B108K, CY14B108M AC Switching Characteristics Parameters Cypress Alt Parameters Parameters SRAM Read Cycle tACE tACS [15] tRC tRC tAA tAA [16] tDOE tOE [16] tOH tOHA tLZCE [12, 17] tLZ tHZCE [12, 17] tHZ [12, 17] tLZOE tOLZ tHZOE [12, 17] tOHZ tPU [12] tPA [12] tPD tPS tDBE tLZBE[12] [12] tHZBE SRAM Write Cycle tWC tWC tWP tPWE tSCE tCW tSD tDW tHD tDH tAW tAW tSA tAS tHA tWR [12, 17,18] tHZWE tWZ tLZWE [12, 17] tOW tBW - 25 ns Description Chip Enable Access Time Read Cycle Time Address Access Time Output Enable to Data Valid Output Hold After Address Change Chip Enable to Output Active Chip Disable to Output Inactive Output Enable to Output Active Output Disable to Output Inactive Chip Enable to Power Active Chip Disable to Power Standby Byte Enable to Data Valid Byte Enable to Output Active Byte Disable to Output Inactive Write Cycle Time Write Pulse Width Chip Enable To End of Write Data Setup to End of Write Data Hold After End of Write Address Setup to End of Write Address Setup to Start of Write Address Hold After End of Write Write Enable to Output Disable Output Active after End of Write Byte Enable to End of Write Min 45 ns Max Min 25 25 Max 45 45 25 12 45 20 3 3 3 3 10 15 0 0 10 15 0 0 25 12 45 20 0 0 10 25 20 20 10 0 20 0 0 15 45 30 30 15 0 30 0 0 10 3 20 15 3 30 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Switching Waveforms Figure 7. SRAM Read Cycle 1: Address Controlled[15, 16, 19] tRC Address Address Valid tAA Data Output Previous Data Valid Output Data Valid tOHA Notes 15. WE must be HIGH during SRAM read cycles. 16. Device is continuously selected with CE, OE and BHE / BLE LOW. 17. Measured 200 mV from steady state output voltage. 18. If WE is LOW when CE goes LOW, the outputs remain in the high impedance state. 19. HSB must remain HIGH during Read and Write cycles. Document #: 001-47378 Rev. *D Page 19 of 31 [+] Feedback CY14B108K, CY14B108M Switching Waveforms Figure 8. SRAM Read Cycle 2: CE and OE Controlled[3, 15, 19] Address Address Valid tRC tACE CE tHZCE tAA tLZCE tHZOE tDOE OE tHZBE tLZOE tDBE BHE, BLE tLZBE Data Output ICC High Impedance Output Data Valid tPU tPD Active Standby Figure 9. SRAM Write Cycle 1: WE Controlled[3, 18, 19, 20] tWC Address Address Valid tSCE tHA CE tBW BHE, BLE tAW tPWE WE tSA tSD Data Input Input Data Valid tHZWE Data Output tHD Previous Data tLZWE High Impedance Note 20. CE or WE must be >VIH during address transitions. Document #: 001-47378 Rev. *D Page 20 of 31 [+] Feedback CY14B108K, CY14B108M Switching Waveforms Figure 10. SRAM Write Cycle 2: CE Controlled[3, 18, 19, 20] tWC Address Valid Address tSA tSCE tHA CE tBW BHE, BLE tPWE WE tHD tSD Input Data Valid Data Input High Impedance Data Output Figure 11. SRAM Write Cycle 3: BHE and BLE Controlled[5, 18, 19, 20, 21] (Not applicable for RTC register writes) tWC Address Address Valid tSCE CE tSA tHA tBW BHE, BLE tAW tPWE WE tSD Data Input tHD Input Data Valid High Impedance Data Output Note 21. Only CE and WE controlled writes to RTC registers are allowed. BLE pin must be held LOW before CE or WE pin goes LOW for writes to RTC register. Document #: 001-47378 Rev. *D Page 21 of 31 [+] Feedback CY14B108K, CY14B108M AutoStore/Power Up RECALL Parameters tHRECALL [22] tSTORE [23] CY14B108K/CY14B108M Description Min Max Power Up RECALL Duration Unit 20 ms STORE Cycle Duration 8 ms tDELAY [24] Time Allowed to Complete SRAM Write Cycle 25 ns VSWITCH Low Voltage Trigger Level tVCCRISE[12] VCC Rise Time VHDIS[12] HSB Output Disable Voltage 1.9 V tLZHSB[12] HSB To Output Active Time 5 s tHHHD[12] HSB High Active Time 500 ns 2.65 V s 150 Switching Waveforms Figure 12. AutoStore or Power Up RECALL[25] VCC VSWITCH VHDIS VVCCRISE Note 23 tSTORE tHHHD Note tSTORE Note tHHHD HSB OUT 23 26 tDELAY tLZHSB AutoStore tLZHSB tDELAY POWERUP RECALL Read & Write Inhibited (RWI) tHRECALL POWER-UP RECALL Read & Write tHRECALL BROWN OUT AutoStore POWER-UP RECALL Read & Write POWER DOWN AutoStore Notes 22. tHRECALL starts from the time VCC rises above VSWITCH. 23. If an SRAM write has not taken place since the last nonvolatile cycle, no AutoStore or Hardware STORE takes place. 24. On a Hardware Store and AutoStore initiation, SRAM write operation continues to be enabled for time tDELAY. 25. Read and Write cycles are ignored during STORE, RECALL, and while VCC is below VSWITCH. 26. HSB pin is driven HIGH to VCC only by internal 100 k resistor, HSB driver is disabled. Document #: 001-47378 Rev. *D Page 22 of 31 [+] Feedback CY14B108K, CY14B108M Software Controlled STORE and RECALL Cycle In the following table, the software controlled STORE and RECALL cycle parameters are listed. [27, 28] Parameters tRC tSA tCW tHA tRECALL tSS [29, 30] 25 ns Description Min 25 0 20 0 STORE/RECALL Initiation Cycle Time Address Setup Time Clock Pulse Width Address Hold Time RECALL Duration Soft Sequence Processing Time 45 ns Max Min 45 0 30 0 200 100 Unit Max ns ns ns ns s s 200 100 Switching Waveforms Figure 13. CE and OE Controlled Software STORE and RECALL Cycle[28] tRC Address tRC Address #1 tSA Address #6 tCW tCW CE tHA tSA tHA tHA tHA OE tHHHD HSB (STORE only) tHZCE tLZCE t DELAY 31 Note tLZHSB High Impedance tSTORE/tRECALL DQ (DATA) RWI Figure 14. AutoStore Enable and Disable Cycle Address tSA CE tRC tRC Address #1 Address #6 tCW tCW tHA tSA tHA tHA tHA OE tLZCE tHZCE tSS 31 Note t DELAY DQ (DATA) Notes 27. The software sequence is clocked with CE controlled or OE controlled reads. 28. The six consecutive addresses must be read in the order listed in Table 2. WE must be HIGH during all six consecutive cycles. 29. This is the amount of time it takes to take action on a soft sequence command. Vcc power must remain HIGH to effectively register command. 30. Commands such as STORE and RECALL lock out I/O until operation is complete which further increases this time. See the specific command. 31. DQ output data at the sixth read may be invalid since the output is disabled at tDELAY time. Document #: 001-47378 Rev. *D Page 23 of 31 [+] Feedback CY14B108K, CY14B108M Hardware STORE Cycle Parameters CY14B108K/CY14B108M Description Min tDHSB HSB To Output Active Time when write latch not set tPHSB Hardware STORE Pulse Width Max 25 Unit ns 15 ns Switching Waveforms Figure 15. Hardware STORE Cycle[23] Write latch set tPHSB HSB (IN) tSTORE tDELAY tHHHD HSB (OUT) tLZHSB DQ (Data Out) RWI Write latch not set tPHSB HSB pin is driven high to VCC only by Internal 100kOhm resistor, HSB driver is disabled SRAM is disabled as long as HSB (IN) is driven low. HSB (IN) HSB (OUT) tDELAY tDHSB tDHSB RWI Figure 16. Soft Sequence Processing[29, 30] Soft Sequence Command Address Address #1 tSA Address #6 tCW tSS Soft Sequence Command Address #1 tSS Address #6 tCW CE VCC Document #: 001-47378 Rev. *D Page 24 of 31 [+] Feedback CY14B108K, CY14B108M Truth Table For SRAM Operations HSB should remain HIGH for SRAM Operations. For x8 Configuration Inputs and Outputs[2] CE WE OE H X X High Z Deselect/Power Down Mode Standby Power L H L Data Out (DQ0-DQ7); Read Active L H H High Z Output Disabled Active L L X Data in (DQ0-DQ7); Write Active For x16 Configuration CE WE OE BHE[3] BLE[3] Inputs and Outputs[2] H X X X X High Z Deselect/Power Down Standby L X X H H High Z Output Disabled Active Mode Power L H L L L Data Out (DQ0-DQ15) Read Active L H L H L Data Out (DQ0-DQ7); DQ8-DQ15 in High Z Read Active L H L L H Data Out (DQ8-DQ15); DQ0-DQ7 in High Z Read Active L H H L L High Z Output Disabled Active L H H H L High Z Output Disabled Active L H H L H High Z Output Disabled Active L L X L L Data In (DQ0-DQ15) Write Active L L X H L Data In (DQ0-DQ7); DQ8-DQ15 in High Z Write Active L L X L H Data In (DQ8-DQ15); DQ0-DQ7 in High Z Write Active Document #: 001-47378 Rev. *D Page 25 of 31 [+] Feedback CY14B108K, CY14B108M Part Numbering Nomenclature CY14 B 108 K - ZSP 25 X I T Option: T - Tape & Reel Blank - Std. Pb-Free Package: ZSP - 44 TSOP II ZSP - 54 TSOP II Temperature: I - Industrial (-40 to 85C) Speed: 25 - 25 ns 45 - 45 ns Data Bus: K - x8 + RTC M - x16 + RTC Density: 108 - 8 Mb Voltage: B - 3.0V 14 - NVSRAM Cypress Document #: 001-47378 Rev. *D Page 26 of 31 [+] Feedback CY14B108K, CY14B108M Ordering Information Speed (ns) 25 45 Ordering Code Package Diagram Package Type CY14B108K-ZS25XIT 51-85087 44-pin TSOPII CY14B108K-ZS25XI 51-85187 44-pin TSOPII CY14B108M-ZSP25XIT 51-85160 54-pin TSOPII CY14B108M-ZSP25XI 51-85160 54-pin TSOPII CY14B108K-ZS45XIT 51-85087 44-pin TSOPII CY14B108K-ZS45XI 51-85187 44-pin TSOPII CY14B108M-ZSP45XIT 51-85160 54-pin TSOPII CY14B108M-ZSP45XI 51-85160 54-pin TSOPII Operating Range Industrial All the above parts are Pb-free. Document #: 001-47378 Rev. *D Page 27 of 31 [+] Feedback CY14B108K, CY14B108M Package Diagrams Figure 17. 44-Pin TSOP II (51-85087) 51-85087 *B Document #: 001-47378 Rev. *D Page 28 of 31 [+] Feedback CY14B108K, CY14B108M Package Diagrams (continued) Figure 18. 54-Pin TSOP II (51-85160) 51-85160 ** Document #: 001-47378 Rev. *D Page 29 of 31 [+] Feedback CY14B108K, CY14B108M Document History Page Document Title: CY14B108K, CY14B108M 8 Mbit (1024K x 8/512K x 16) nvSRAM with Real Time Clock Document Number: 001-47378 Rev. ECN No. Orig. of Change Submission Date Description of Change ** 2681767 GVCH/PYRS 04/01/09 *A 2712462 GVCH/PYRS 05/29/2009 Moved data sheet status from Preliminary to Final Updated AutoStore operation Updated C1, C2 values to 12pF, 69pF from 21pF, 21pF respectively Updated ISB test condition Updated footnote 10 Updated IBAK and VRTCcap parameter values Added RBKCHG parameter to RTC characteristics table Added footnote 14 Referenced footnote 12 to VCCRISE, tHHHD and tLZHSB parameters Updated VHDIS parameter description *B 2746310 GVCH 07/29/2009 Page 4: Updated Hardware STORE (HSB) operation description page 4: Updated Software STORE description Updated tDELAY parameter description Updated footnote 24 and added footnote 31 Referenced footnote 31 to Figure 11 and Figure 12 *C 2759948 GVCH 09/04/2009 Removed commercial temperature related specs Removed 20 ns access speed related specs Changed VRTCbat max value from 3.3V to 3.6V Changed RBKCHG min value from 450 to 350 Updated footnote 14 *D 2828257 GVCH 12/15/2009 Changed STORE cycles to QuantumTrap from 200K to 1 Million Updated IBAK RTC backup current spec unit from nA to A Added Contents on page 2 Document #: 001-47378 Rev. *D New Data Sheet Page 30 of 31 [+] Feedback CY14B108K, CY14B108M Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at cypress.com/sales. Products PSoC Clocks & Buffers psoc.cypress.com clocks.cypress.com Wireless wireless.cypress.com Memories memory.cypress.com Image Sensors USB image.cypress.com psoc.cypress.com/usb (c) Cypress Semiconductor Corporation, 2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress' product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document #: 001-47378 Rev. *D Revised December 15, 2009 Page 31 of 31 All products and company names mentioned in this document are the trademarks of their respective holders. [+] Feedback