Fully Accurate, 12-/14-/16-Bit VOUT nanoDAC, Quad,
SPI Interface, 4.5 V to 5.5 V in TSSOP
Data Sheet AD5024/AD5044/AD5064
Rev. G Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2008–2016 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
FEATURES
Low power quad 12-/14-/16-bit DAC, ±1 LSB INL
Pin compatible and performance upgrade to AD5666
Individual and common voltage reference pin options
Rail-to-rail operation
4.5 V to 5.5 V power supply
Power-on reset to zero scale or midscale
3 power-down functions and per-channel power-down
Hardware LDAC with software LDAC override function
CLR function to programmable code
SDO daisy-chaining option
14-/16-lead TSSOP
Internal reference buffer and internal output amplifier
APPLICATIONS
Process control
Data acquisition systems
Portable battery-powered instruments
Digital gain and offset adjustment
Programmable voltage and current sources
Programmable attenuators
FUNCTIONAL BLOCK DIAGRAMS
06803-064
INTERFACE
LOGIC AND
SHIFT
REGISTER
INPUT
REGISTER
DIN
SDO
LDAC
GND
V
DD
LDAC
V
REFIN
S
YNC
SCLK
AD5064-1
CLR
V
OUT
A
V
OUT
B
V
OUT
C
V
OUT
D
DAC
REGISTER DAC A
BUFFER
INPUT
REGISTER
DAC
REGISTER DAC B
BUFFER
INPUT
REGISTER
DAC
REGISTER DAC C
BUFFER
INPUT
REGISTER
DAC
REGISTER DAC D
BUFFER
POR
POWER-DOWN
LOGIC
POWER-ON
RESET
Figure 1. AD5064-1 Functional Equivalent and Pin Compatible with AD5666
INTERFACE
LOGIC AND
SHIFT
REGISTER
INPUT
REGISTER
DIN
LDAC
GND
V
DD
LDAC
V
REF
A
SYNC
SCLK
AD5024/
AD5044/
AD5064
CLR
V
OUT
A
V
OUT
B
V
OUT
C
V
OUT
D
DAC
REGISTER DAC A
BUFFER
INPUT
REGISTER
DAC
REGISTER DAC B
BUFFER
INPUT
REGISTER
DAC
REGISTER DAC C
BUFFER
INPUT
REGISTER
DAC
REGISTER DAC D
BUFFER
V
REF
B
V
REF
CV
REF
D
POR
POWER-DOWN
LOGIC
POWER-ON
RESET
06803-001
Figure 2. AD5024/AD5044/AD5064 with Individual Reference Pins
GENERAL DESCRIPTION
The AD5024/AD5044/AD5064/AD5064-1 are low power, quad
12-/14-/16-bit buffered voltage output nanoDAC® converters
that offer relative accuracy specifications of 1 LSB INL and 1 LSB
DNL with the AD5024/AD5044/AD5064 individual reference
pin and the AD5064-1 common reference pin options. The
AD5024/AD5044/AD5064/AD5064-1 can operate from a single
4.5 V to 5.5 V supply. The AD5024/AD5044/AD5064/AD5064-1
also offer a differential accuracy specification of ±1 LSB. The
devices use a versatile 3-wire, low power Schmitt trigger serial
interface that operates at clock rates up to 50 MHz and is compati-
ble with standard SPI, QSPI™, MICROWIRE, and DSP interface
standards. Integrated reference buffers and output amplifiers are
also provided on-chip. The AD5024/AD5044/AD5064/AD5064-1
incorporate a power-on reset circuit that ensures the DAC
output powers up to zero scale or midscale and remains there
until a valid write takes place to the device. The AD5024/AD5044/
AD5064/AD5064-1 contain a power-down feature that reduces
the current consumption of the device to typically 400 nA at 5 V
and provides software selectable output loads while in power-
down mode. Total unadjusted error for the devices is <2 mV.
PRODUCT HIGHLIGHTS
1. Quad channel available in 14-/16-lead TSSOPs.
2. 16-bit accurate, 1 LSB INL.
3. High speed serial interface with clock speeds up to 50 MHz.
4. Reset to known output voltage (zero scale or midscale).
Table 1. Related Devices
Device No. Description
AD5666 Quad,16-bit buffered DAC,
16 LSB INL, TSSOP
AD5025/AD5045/AD5065 Dual, 16-bit buffered DACs,
1 LSB INL, TSSOP
AD5062, AD5063 16-bit nanoDAC, 1 LSB INL, SOT-23,
MSOP
AD5061 16-bit nanoDAC, 4 LSB INL, SOT-23
AD5040/AD5060 14-/16-bit nanoDAC, 1 LSB INL,
SOT-23
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 2 of 28
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagrams ............................................................. 1
General Description ......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
AC Characteristics ........................................................................ 4
Timing Characteristics ................................................................ 5
Absolute Maximum Ratings ............................................................ 7
ESD Caution .................................................................................. 7
Pin Configurations and Function Descriptions ........................... 8
Typical Performance Characteristics ........................................... 10
Terminology .................................................................................... 17
Theory of Operation ...................................................................... 19
Digital-to-Analog Converter .................................................... 19
DAC Architecture ....................................................................... 19
Reference Buffer ......................................................................... 19
Output Amplifier ........................................................................ 19
Serial Interface ............................................................................ 19
Shift Register ............................................................................... 19
Modes of Operation ................................................................... 21
Power-On Reset .......................................................................... 22
Power-Down Modes .................................................................. 22
Clear Code Register ................................................................... 23
LDAC Function .......................................................................... 23
Power Supply Bypassing and Grounding ................................ 24
Microprocessor Interfacing ....................................................... 25
Applications Information .............................................................. 26
Using a Reference as a Power Supply ....................................... 26
Bipolar Operation....................................................................... 26
Using the AD5024/AD5044/AD5064/AD5064-1 with a
Galvanically Isolated Interface ................................................. 26
Outline Dimensions ....................................................................... 27
Ordering Guide .......................................................................... 28
REVISION HISTORY
6/2016—Rev. F to Rev. G
Changed ADSP-BF53x to ADSP-BF527 ..................... Throughout
Changes to Power-On Reset Section ............................................ 22
6/2013—Rev. E to Rev. F
Change to Standalone Mode Section ........................................... 21
5/2011—Rev. D to Rev. E
Changes to Table 4 ............................................................................ 5
Changes to Figure 4 and Figure 5 ................................................... 6
8/20—Rev. C to Rev. D
Change to Minimum SYNC High Time (Single Channel
Update) Parameter, Table 4 ............................................................. 5
5/2010—Rev. B to Rev. C
Changes to Power-On Reset Section ............................................ 22
6/2009—Rev. A to Rev. B
Changes to Figure 1 .......................................................................... 1
3/2009—Rev. 0 to Rev. A
Added 14-Lead TSSOP ...................................................... Universal
Added Figure 1; Renumbered Sequentially .................................. 1
Changes to Features Section, General Description Section,
Product Highlights Section, Figure 2, and Table 1 ....................... 1
Changes to Table 2 ............................................................................ 3
Changes to Timing Characteristics Section and Table 4 .............. 5
Added Circuit and Timing Diagrams Section and Figure 3 ........ 5
Added Figure 5 ................................................................................... 6
Changes to Figure 4 ........................................................................... 6
Added Figure 6 ................................................................................... 8
Added Table 6; Renumbered Sequentially ..................................... 8
Changed Input Shift Register to Shift Register Throughout ....... 8
Changes to Table 7 ............................................................................. 9
Changes to Typical Performance Characteristics Section ........ 10
Changes to Terminology Section ................................................. 17
Changes to Digital-to-Analog Converter Section, Reference
Buffer Section, Output Amplifier Section, Serial Interface
Section, Shift Register Section, and Table 8 ................................ 19
Changes to Figure 47, Figure 48, and Figure 49 Captions ........ 20
Added Modes of Operation Section, Daisy-Chaining Section,
Table 10, and Table 11 .................................................................... 21
Changes to Table 13 and Power-Down Mode Section .............. 22
Changes to Table 16 ....................................................................... 24
Changes to Figure 52 to Figure 55 ................................................ 25
Changes to Bipolar Operation Section and Figure 56 to
Figure 58 .......................................................................................... 26
Added Figure 59 ............................................................................. 27
Updated Outline Dimensions ....................................................... 27
Changes to Ordering Guide .......................................................... 28
8/2008—Revision 0: Initial Version
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 3 of 28
SPECIFICATIONS
VDD = 4.5 V to 5.5 V, RL = 5 kΩ to GND, CL = 200 pF to GND, 2.5 V ≤ VREFIN ≤ VDD, unless otherwise specified. All specifications TMIN to
TMAX, unless otherwise noted.
Table 2.
Parameter
B Grade1 A Grade1, 2
Unit Test Conditions/Comments
Min Typ Max Min Typ Max
STATIC PERFORMANCE3
Resolution 16 16 Bits
AD5064/AD5064-1
14 Bits
AD5044
12 Bits
AD5024
Relative Accuracy (INL)4 ±0.5 ±1 ±0.5 ±4 LSB
AD5064/AD5064-1; TA = −40°C to +105°C
±0.5 ±2 ±0.5 ±4 LSB
AD5064/AD5064-1; TA = −40°C to +125°C
±0.25 ±1 LSB
AD5044
±0.12 ±0.5 LSB
AD5024
Differential Nonlinearity (DNL)4 ±0.2 ±1 ±0.2 ±1 LSB
Total Unadjusted Error ±2 ±2 mV VREF = 2.5 V, VDD = 5.5 V
Offset Error4, 5 ±0.2 ±1.8 ±0.2 ±1.8 mV
Offset Error Temperature
Coefficient4, 6
±2 ±2 µV/°C
Full-Scale Error4 ±0.01 ±0.07 ±0.01 ±0.07 % FSR
All 1s loaded to DAC register, VREF < VDD
Gain Error4 ±0.005 ±0.05 ±0.005 ±0.05 % FSR
VREF < VDD
Gain Temperature Coefficient4, 6 ±1 ±1 ppm
FSR/°C
DC Crosstalk4, 6 40 40 µV Due to single-channel, full-scale output
change, RL = 5 kΩ to GND or VDD
40 40 µV/mA Due to load current change
40 40 µV Due to powering down (per channel)
OUTPUT CHARACTERISTICS6
Output Voltage Range 0 VDD 0 VDD V
Capacitive Load Stability 1 1 nF RL = 5 kΩ, RL =100 kΩ, and RL = ∞
DC Output Impedance
Normal Mode 0.5 0.5
Power-Down Mode
Output Connected to
100 kΩ Network
100 100 kΩ Output impedance tolerance ± 20 kΩ
Output Connected to
1 kΩ Network
1 1 kΩ Output impedance tolerance ± 400 Ω
Short-Circuit Current 60 60 mA DAC = full scale, output shorted to GND
45 45 mA DAC = zero scale, output shorted to VDD
Power-Up Time7 4.5 4.5 µs
DC PSRR −92 −92 dB VDD ± 10%, DAC = full scale, VREF < VDD
REFERENCE INPUTS
Reference Input Range 2.2 VDD 2.2 VDD V
Reference Current 35 50 35 50 µA Per DAC channel; individual reference
option
140 160 140 160 µA Single reference option
Reference Input Impedance 120 120 kΩ Individual reference option
32 32 kΩ Single reference option
LOGIC INPUTS
Input Current8 ±1 ±1 µA
Input Low Voltage, VINL 0.8 0.8 V
Input High Voltage, VINH 2.2 2.2 V
Pin Capacitance6 4 4 pF
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 4 of 28
Parameter
B Grade1 A Grade1, 2
Unit Test Conditions/Comments
Min Typ Max Min Typ Max
LOGIC OUTPUTS (SDO)9
Output Low Voltage, VOL 0.4 0.4 V ISINK = 2 mA
Output High Voltage, VOH V
DD − 1 VDD − 1 ISOURCE = 2 mA
High Impedance Leakage
Current
±0.002 ±1 ±0.002 ±1 A
High Impedance Output
Capacitance6
7 7 pF
POWER REQUIREMENTS
VDD 4.5 5.5 4.5 5.5 V DAC active, excludes load current
IDD10 V
IH = VDD, VIL = GND, Code = midscale
Normal Mode 4 6 4 6 mA
All Power-Down Modes11 0.4 2 0.4 2 µA TA = −40°C to +105°C
30 30 µA TA = −40°C to +125°C
1 Temperature range is −40°C to +125°C, typical at 25°C.
2 A grade offered in AD5064 only.
3 Linearity and total unadjusted error are calculated using a reduced code range—AD5064/AD5064-1: Code 512 to Code 65,024; AD5044: Code 128 to Code 16,256;
AD5024: Code 32 to Code 4064. Output unloaded.
4 See the Terminology section.
5 Offset error calculated using a reduced code range—AD5064/AD5064-1: Code 512 to Code 65,024; AD5044: Code 128 to Code 16,256; AD5024: Code 32 to Code 4064.
Output unloaded
6 Guaranteed by design and characterization; not production tested.
7 Time to exit power-down mode to normal mode; 32nd clock edge to 90% of DAC midscale value, output unloaded.
8 Current flowing into individual digital pins. VDD = 5.5 V; VREF = 4.096 V; Code = midscale.
9 AD5064-1 only.
10 Interface inactive. All DACs active. DAC outputs unloaded.
11 All four DACs powered down.
AC CHARACTERISTICS
VDD = 4.5 V to 5.5 V, RL = 5 kΩ to GND, CL = 200 pF to GND, 2.5 V ≤ VREFIN ≤ VDD. All specifications TMIN to TMAX, unless otherwise
noted.
Table 3.
Parameter1, 2 Min Typ Max Unit Test Conditions/Comments3
Output Voltage Settling Time 5.8 8 µs ¼ to ¾ scale and ¾ to ¼ scale settling to ±1 LSB, RL = 5 kΩ,
single-channel update
10.7 13 µs
¼ to ¾ scale and ¾ to ¼ scale settling to ±1 LSB, RL = 5 kΩ, all channel
update
Slew Rate 1.5 V/µs
Digital-to-Analog Glitch Impulse 3 nV-sec 1 LSB change around major carry
Reference Feedthrough −90 dB VREF = 3 V ± 0.86 V p-p, frequency = 100 Hz to 100 kHz
Digital Feedthrough 0.1 nV-sec
Digital Crosstalk 1.9 nV-sec
Analog Crosstalk 2 nV-sec
DAC-to-DAC Crosstalk 3.5 nV-sec
AC Crosstalk 6 nV-sec
Multiplying Bandwidth 340 kHz VREF = 3 V ± 0.86 V p-p
Total Harmonic Distortion −80 dB VREF = 3 V ± 0.2 V p-p, frequency = 10 kHz
Output Noise Spectral Density 64 nV/√Hz DAC code = 0x8400, frequency = 1 kHz
60 nV/√Hz DAC code = 0x8400, frequency = 10 kHz
Output Noise 6 V p-p 0.1 Hz to 10 Hz
1 Guaranteed by design and characterization; not production tested.
2 See the Terminology section.
3 Temperature range is −40°C to +125°C, typical at 25°C.
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 5 of 28
TIMING CHARACTERISTICS
All input signals are specified with tR = tF = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. See Figure 4 and
Figure 5. VDD = 4.5 V to 5.5 V. All specifications TMIN to TMAX, unless otherwise noted.
Table 4.
Parameter1 Symbol Min Typ Max Unit
SCLK Cycle Time t1 20 ns
SCLK High Time t2 10 ns
SCLK Low Time t3 10 ns
SYNC to SCLK Falling Edge Setup Time t4 17 ns
Data Setup Time t5 5 ns
Data Hold Time t6 5 ns
SCLK Falling Edge to SYNC Rising Edge t7 5 30 ns
Minimum SYNC High Time (Single Channel Update) t8 3 µs
Minimum SYNC High Time (All Channel Update) t8 8 µs
SYNC Rising Edge to SCLK Fall Ignore t9 17 ns
LDAC Pulse Width Low t10 20 ns
SCLK Falling Edge to LDAC Rising Edge t11 20 ns
CLR Minimum Pulse Width Low t12 10 ns
SCLK Falling Edge to LDAC Falling Edge t13 10 ns
CLR Pulse Activation Time t14 10.6 µs
SCLK Rising Edge to SDO Valid t152, 3 22 ns
SCLK Falling Edge to SYNC Rising Edge t162 5 ns
SYNC Rising Edge to SCLK Rising Edge t172 8 ns
SYNC Rising Edge to LDAC/CLR Falling Edge (Single Channel Update) t182 2 µs
SYNC Rising Edge to LDAC/CLR Falling Edge (All Channel Update) t182 8 µs
Power-up Time4 4.5 µs
1 Maximum SCLK frequency is 50 MHz at VDD = 4.5 V to 5.5 V. Guaranteed by design and characterization; not production tested.
2 Daisy-chain mode only.
3 Measured with the load circuit of Figure 3. t15 determines the maximum SCLK frequency in daisy-chain mode. AD5064-1 only.
4 Time to exit power-down mode to normal mode of AD5024/AD5044/AD5064/AD5064-1, 32nd clock edge to 90% of DAC midscale value, with output unloaded.
Circuit and Timing Diagrams
2mA I
OL
2mA I
OH
TO OUTPUT
PIN C
L
50pF
06803-002
2
V
OH
(MIN) + V
OL
(MAX)
Figure 3. Load Circuit for Digital Output (SDO) Timing Specifications
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 6 of 28
t
4
t
3
SCLK
SYNC
DIN
t
1
t
2
t
5
t
6
t
7
t
8
DB31
t
9
t
10
t
11
LDAC
1
LDAC
2
t
13
1
ASYNCHRONOUS LDAC UPDATE MODE.
2
SYNCHRONOUS LDAC UPDATE MODE.
CLR
t
12
t
14
V
OUT
DB0
06803-003
Figure 4. Serial Write Operation
t
8
t
4
t
6
t
15
t
18
t
16
t
17
t
10
t
5
32 64
SCLK
SYNC
DIN
SDO
UNDEFINED
INPUT WORD FOR DAC N
INPUT WORD FOR DAC N
INPUT WORD FOR DAC N + 1
DB0DB31 DB0
DB31
DB31 DB0
t
18
t
12
06803-004
LDAC
1
1
IF IN DAISY-CHAIN MODE, LDAC MUST BE USED ASYNCHRONOUSLY.
CLR
Figure 5. Daisy-Chain Timing Diagram
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 7 of 28
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 5.
Parameter Rating
VDD to GND −0.3 V to +7 V
Digital Input Voltage to GND −0.3 V to VDD + 0.3 V
VOUT to GND −0.3 V to VDD + 0.3 V
VREF to GND −0.3 V to VDD + 0.3 V
Operating Temperature Range
Industrial −40°C to +125°C
Storage Temperature Range −65°C to +150°C
Junction Temperature (TJ MAX) 150°C
TSSOP
Power Dissipation (TJ MAXTA)/θJA
θJA Thermal Impedance 113°C/W
Reflow Soldering Peak Temperature
Pb-Free 260°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 8 of 28
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
POR
V
OUT
C
V
OUT
A
V
REFIN
DIN
GND
V
OUT
B
V
OUT
D
SDO
SCLK
CLR
V
DD
LDAC
SYNC
TOP VIEW
(Not to Scale)
1
2
3
4
5
6
7
AD5064-1
14
13
12
11
10
9
8
0
6803-065
Figure 6. 14-Lead TSSOP (RU-14)
Table 6. 14-Lead TSSOP (RU-14) Pin Function Descriptions
Pin No. Mnemonic Description
1 LDAC LDAC can be operated in two modes, asynchronously and synchronously, as shown in Figure 4. Pulsing
this pin low allows any or all DAC registers to be updated if the input registers have new data. This allows
all DAC outputs to simultaneously update. This pin can also be tied permanently low in standalone mode.
When daisy-chain mode is enabled, this pin cannot be tied permanently low; the LDAC pin should be
used in asynchronous LDAC update mode, as shown in Figure 5, and the LDAC pin must be brought
high after pulsing.
2 SYNC Active Low Control Input. This is the frame synchronization signal for the input data. When SYNC goes
low, it powers on the SCLK and DIN buffers and enables the shift register. Data is transferred in on the
falling edges of the next 32 clocks. If SYNC is taken high before the 32nd falling edge, the rising edge of
SYNC acts as an interrupt and the write sequence is ignored by the device.
3 VDD Power Supply Input. These devices can be operated from 4.5 V to 5.5 V, and the supply should be
decoupled with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND.
4 VOUTA Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation.
5 VOUTC Analog Output Voltage from DAC C. The output amplifier has rail-to-rail operation.
6 POR Power-On Reset Pin. Tying this pin to GND powers up all four DACs to zero scale. Tying this pin to VDD
powers up all four DACs to midscale.
7 VREFIN This is a common pin for reference input for DAC A, DAC B, DAC C, and DAC D.
8 SDO Serial Data Output. Can be used to daisy-chain a number of AD5064-1 devices together. The serial data
is transferred on the rising edge of SCLK and is valid on the falling edge of the clock.
9 CLR Asynchronous Clear Input. The CLR input is falling edge sensitive. When CLR is low, all LDAC pulses are
ignored. When CLR is activated, the input register and the DAC register are updated with the data
contained in the clear code register—zero, midscale, or full scale. Default setting clears the output to 0 V.
10 VOUTD Analog Output Voltage from DAC D. The output amplifier has rail-to-rail operation.
11 VOUTB Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation.
12 GND Ground Reference Point for All Circuitry on the Device.
13 DIN Serial Data Input. This device has a 32-bit shift register. Data is clocked into the shift register on the
falling edge of the serial clock input.
14 SCLK Serial Clock Input. Data is clocked into the shift register on the falling edge of the serial clock input. Data
can be transferred at rates of up to 50 MHz.
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 9 of 28
V
OUT
A
V
REF
A
V
REF
B
V
OUT
C
POR
DIN
GND
V
OUT
B
V
OUT
D
V
REF
C
V
REF
D
SCLK
CLR
V
DD
LDAC
SYNC
TOP VIEW
(Not to Scale)
1
2
3
4
5
6
7
8
AD5024/
AD5044/
AD5064
16
15
14
13
12
11
10
9
06803-005
Figure 7. 16-Lead TSSOP (RU-16) Pin Configuration
Table 7. 16-Lead TSSOP (RU-16) Pin Function Descriptions
Pin No. Mnemonic Description
1 LDAC LDAC can be operated in two modes, asynchronously and synchronously, as shown in Figure 4. Pulsing
this pin low allows any or all DAC registers to be updated if the input registers have new data. This allows
all DAC outputs to simultaneously update. This pin can also be tied permanently low in standalone mode.
2 SYNC Active Low Control Input. This is the frame synchronization signal for the input data. When SYNC goes
low, it powers on the SCLK and DIN buffers and enables the shift register. Data is transferred in on the
falling edges of the next 32 clocks. If SYNC is taken high before the 32nd falling edge, the rising edge of
SYNC acts as an interrupt and the write sequence is ignored by the device.
3 VDD Power Supply Input. These devices can be operated from 4.5 V to 5.5 V, and the supply should be
decoupled with a 10 µF capacitor in parallel with a 0.1 µF capacitor to GND.
4 VREFB DAC B Reference Input. This is the reference voltage input pin for DAC B.
5 VREFA DAC A Reference Input. This is the reference voltage input pin for DAC A.
6 VOUTA Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation.
7 VOUTC Analog Output Voltage from DAC C. The output amplifier has rail-to-rail operation.
8 POR Power-On Reset. Tying this pin to GND powers up the device to 0 V. Tying this pin to VDD powers up the
device to midscale.
9 VREFC DAC C Reference Input. This is the reference voltage input pin for DAC C.
10 CLR Asynchronous Clear Input. The CLR input is falling edge sensitive. When CLR is low, all LDAC pulses are
ignored. When CLR is activated, the input register and the DAC register are updated with the data
contained in the clear code register—zero, midscale, or full scale. Default setting clears the output to 0 V.
11 VREFD DAC D Reference Input. This is the reference voltage input pin for DAC D.
12 VOUTD Analog Output Voltage from DAC D. The output amplifier has rail-to-rail operation.
13 VOUTB Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation.
14 GND Ground Reference Point for All Circuitry on the Device.
15 DIN Serial Data Input. This device has a 32-bit shift register. Data is clocked into the shift register on the
falling edge of the serial clock input.
16 SCLK Serial Clock Input. Data is clocked into the shift register on the falling edge of the serial clock input. Data
can be transferred at rates of up to 50 MHz.
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 10 of 28
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
0.2
0
–0.6
–1.0
512 16,640 32,768 48,896 65,024
06803-019
INL (LSB)
DAC CODE
0.8
0.6
0.4
–0.4
–0.2
–0.8
V
DD
= 5V
V
REF
= 4.096V
T
A
= 25°C
Figure 8. AD5064/AD5064-1 INL
1.0
0.2
0
–0.6
–1.0
06803-020
INL (LSB)
DAC CODE
0.8
0.6
0.4
–0.4
–0.2
–0.8
0 512 1024 1536 2048 2560 3072 3584 4096
V
DD
= 5V
V
REF
= 4.096V
T
A
= 25°C
Figure 9. AD5044 INL
1.0
0.2
0
–0.6
–1.0
06803-021
INL (LSB)
DAC CODE
0.8
0.6
0.4
–0.4
–0.2
–0.8
0 512 1024 1536 2048 2560 3072 3584 4096
V
DD
= 5V
V
REF
= 4.096V
T
A
= 25°C
Figure 10. AD5024 INL
1.0
0.2
0
–1.0
–0.4
512 16,640 32,768 48,896 65,024
06803-022
DNL (LSB)
DAC CODE
–0.8
–0.6
–0.2
0.8
0.6
0.4
V
DD
= 5V
V
REF
= 4.096V
T
A
= 25°C
Figure 11. AD5064/AD5064-1 DNL
1.0
0.2
0
–0.6
–1.0
06803-023
DNL (LSB)
DAC CODE
0.8
0.6
0.4
–0.4
–0.2
–0.8
0 4096 8192 12,288 16,384
V
DD
= 5V
V
REF
= 4.096V
T
A
= 25°C
Figure 12. AD5044 DNL
1.00
0
06803-024
DNL (LSB)
DAC CODE
0.75
0.50
0.25
–1.00
–0.75
–0.50
–0.25
0 4096 8192 12,288 16,384
V
DD
= 5V
V
REF
= 4.096V
T
A
= 25°C
Figure 13. AD5024 DNL
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 11 of 28
0.20
0.10
0
–0.10
–0.20
512 16,640 32,768 48,896 65,024
06803-025
TUE (mV)
DAC CODE
0.15
–0.05
0.05
–0.15
V
DD
= 5V
V
REF
= 4.096V
T
A
= 25°C
Figure 14. Total Unadjusted Error (TUE)
06803-026
2.0
–1.6
–1.4
–1.2
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
5.55.04.54.03.53.02.5
INL ERROR (LSB)
REFERENCE VOLTAGE (V)
MAX INL ERROR @ V
DD
= 5.5V
MIN INL ERROR @ V
DD
= 5.5V
T
A
= 25°C
Figure 15. INL vs. Reference Input Voltage
06803-027
2.0
–1.6
–1.4
–1.2
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
5.55.04.54.03.53.02.5
DNL ERROR (LSB)
REFERENCE VOLTAGE (V)
T
A
= 25°C
MAX DNL ERROR @ V
DD
= 5.5V
MIN DNL ERROR @ V
DD
= 5.5V
Figure 16. DNL vs. Reference Input Voltage
06803-028
2.0
–1.2
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
5.55.04.54.03.53.02.5
TUE (mV)
REFERENCE VOLTAGE (V)
MAX TUE @ V
DD
= 5.5V
MIN TUE @ V
DD
= 5.5V
T
A
= 25°C
Figure 17. TUE vs. Reference Input Voltage
0.015
0.010
0.005
0
–0.015
–60 –20 40 80 140
06803-029
GAIN ERROR (%FSR)
TEMPERATURE (°C)
–0.005
–0.010
–40 0 20 60 100 120
V
DD
= 5.5V
V
REF
= 4.096V
DAC A
DAC B
DAC C
DAC D
Figure 18. Gain Error vs. Temperature
DAC A
0.6
0.4
0.3
0
–0.4
–60 0 40 80 140
06803-030
OFFSET ERROR (mV)
TEMPERATURE (ºC)
0.5
0.2
0.1
–0.1
–0.2
–0.3
–40 20–20 60 100 120
DAC C
DAC D
DAC B
V
DD
= 5.5V
V
REF
= 4.096V
Figure 19. Offset Error vs. Temperature
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 12 of 28
0.2
0.1
0
–0.1
–0.2
4.50 4.75 5.00 5.25 5.50
06803-031
ERROR (%FSR)
V
DD
(V)
GAIN ERROR
FULL-SCALE ERROR
V
REF
= 4.096V
T
A
= 25°C
Figure 20. Gain Error and Full-Scale Error vs. Supply Voltage
0.12
0.09
0.06
0.03
0
4.50 4.75 5.00 5.25 5.50
06803-032
OFFSET ERROR (mV)
V
DD
(V)
V
REF
= 4.096V
T
A
= 25°C
Figure 21. Offset Error Voltage vs. Supply Voltage
06803-033
I
DD POWER-UP
(mA)
HITS
3.9 4.0 4.1 4.2 4.3
0
5
10
15
20
25
30
35
40 MEAN: 4.11699
SD: 0.0544403
LIMITS: LOW: 3 HIGH: 4.3
CPk: LOW: 6.84 HIGH: 1.12
V
REF
= 4.096V
T
A
= 25°C
CODE = MIDSCALE
Figure 22. IDD Histogram, VDD = 5.0 V
06803-034
0
2
4
6
8
10
0 10,000 20,000 30,000 40,000 50,000 60,000 70,000
DAC CODE
I
DD
(mA)
V
DD
= 5.5V
V
REF
= 4.096
T
A
= 25°C
Figure 23. Supply Current vs. Code
06803-035
0
2
4
6
8
10
I
DD
(mA)
TEMPERATURE (°C)
V
DD
= 5.5V
V
REF
= 4.096
CODE = MIDSCALE
–40 –20 0 20 40 60 80 100 120
Figure 24. Supply Current vs. Temperature
06803-036
SUPPLY VOLTAGE (V)
I
DD
(mA)
0
2
4
6
8
10
V
DD
= 5.5V
V
REF
= 4.096
T
A
= 25°C
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
Figure 25. Supply Current vs. Supply Voltage
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 13 of 28
06803-037
DIGITAL INPUT VOLTAGE (V)
I
DD
(mA)
0
2
4
6
8
10
012345
V
DD
= 5.5V
V
REF
= 4.096
T
A
= 25°C
Figure 26. Supply Current vs. Digital Input Voltage
5.0
4.0
3.0
2.0
0
06803-038
OUTPUT VOLTAGE (V)
TIME (µs)
1.0
4.5
3.5
2.5
1.5
0.5
V
DD
= 5V, V
REF
= 4.096V
T
A
= 25ºC
1/4 SCALE TO 3/4 SCALE
3/4 SCALE TO 1/4 SCALE
OUTPUT LOADED WITH 5k
AND 200pF TO GND
02468101214
Figure 27. Settling Time
06803-039
CH1 2V CH3 2V M2ms A CH1 2.52V
3
1
T 20.4%
V
REF
= 4.096V
T
A
= 25°C
V
DD
DAC A
Figure 28. Power-On Reset to 0 V
06803-040
CH1 2V CH3 2V M2ms A CH1 2.52V
3
1
T 20.4%
V
REF
= 4.096V
T
A
= 25°C
OUTPUT UNLOADED V
DD
DAC A
Figure 29. Power-On Reset to Midscale
06803-041
CH1 5V CH2 500mV M2µs A CH2 1.2V
2
1
T 55%
CH1 = SCLK
CH2 = V
OUT
V
DD
= 5V
POWER-UP TO MIDSCALE
OUTPUT UNLOADED
Figure 30. Exiting Power-Down to Midscale
6
3
1
–1
–3 0 2.5 5.0 7.5 10.0
06803-042
GLITCH AMPLITUDE (mV)
TIME (μs)
5
4
2
–2
0
VDD = 5V
V
REF
= 4.096V
T
A
= 25°C
CODE = 0x8000 TO 0x7FFF
OUTPUT UNLOADED WITH 5k
AND 200pF
Figure 31. Digital-to-Analog Glitch Impulse
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 14 of 28
7
4
1
–1
–4 0 2.5 5.0 7.5 10.0
06803-043
GLITCH AMPLITUDE (mV)
TIME (μs)
5
6
3
2
0
–2
–3
V
DD
= 5V, V
REF
= 4.096V
T
A
= 25ºC
Figure 32. Analog Crosstalk
7
4
1
–1
–4 0 2.5 5.0 7.5 10.0
06803-044
GLITCH AMPLITUDE (mV)
TIME (μs)
5
6
3
2
0
–2
–3
V
DD
= 5V, V
REF
= 4.096V
T
A
= 25°C
Figure 33. DAC-to-DAC Crosstalk
06803-045
4s/DIV
1μV/DI
V
V
DD
= 5V, V
REF
= 4.096V
T
A
= 25ºC
DAC LOADED WITH MIDSCALE
Figure 34. 0.1 Hz to 10 Hz Output Noise Plot
0
–20
–50
–80
–100
510 30 40 55
06803-046
V
OUT
LEVEL (dB)
FREQUENCY (kHz)
–90
–70
–60
–10
–30
–40
20 50
V
DD
= 5V,
T
A
= 25ºC
DAC LOADED WITH MIDSCALE
V
REF
= 3.0V ± 200mV p-p
Figure 35. Total Harmonic Distortion
24
20
14
8
401 5 7 10
06803-047
SETTLING TIME (μs)
CAPACITANCE (nF)
6
10
12
22
18
16
392468
V
DD
= 5V, V
REF
= 3.0V
T
A
= 25°C
1/4 SCALE TO 3/4 SCALE
WITHIN ±1LSB
Figure 36. Settling Time vs. Capacitive Load
06803-048
CH1 5V CH2 2V M2µs A CH1 2.5V
2
1
T11%
VDD = 5V
VREF = 4.096V
TA = 25ºC
DAC A
CLR
Figure 37. Hardware CLR
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 15 of 28
10
0
–10
–20
–6010 100 1000 10000
06803-049
ATTENUATION (dB)
FREQUENCY (kHz)
–30
–40
–50
CH A
CH B
CH C
CH D
3dB POINT
Figure 38. Multiplying Bandwidth
5.0
4.0
3.0
2.0
0
06803-050
OUTPUT VOLTAGE (V)
TIME (µs)
1.0
4.5
3.5
2.5
1.5
0.5
V
DD
= 5V, V
REF
= 4.096V
T
A
= 25°C
1/4 SCALE TO 3/4 SCALE
3/4 SCALE TO 1/4 SCALE
OUTPUT LOADED WITH 5k
AND 200pF TO GND
0 2 4 6 8 10 12 14
Figure 39. Typical Output Slew Rate
0.0010
0.0008
0.0006
0.0004
0.0002
0
–0.0002
–0.0004
–0.0006
–0.0008
–25 –20 –15 –10 –5 0 5 10 15 20 25 30
06803-051
VOLTAGE (V)
CURRENT (mA)
CODE = MIDSCALE
VDD = 5V, VREF = 4.096V
Figure 40. Typical Output Load Regulation
0.10
–0.10
–0.08
–0.06
–0.04
–0.02
0
0.02
0.04
0.06
0.08
–25 –20 –15 –10 –5 0 5 10 15 20 25 30
06803-052
V
OUT
(V)
I
OUT
(mA)
CODE = MIDSCALE
V
DD
= 5V, V
REF
= 4.096V
Figure 41. Typical Current Limiting Plot
06803-053
CH1 50mV CH2 5V M4µs A CH2 1.2V
T8.6%
DAC A 295mV p-p
T
A
= 25°C
V
DD
= 5V, V
REF
= 4.096V
Figure 42. Glitch Upon Entering Power-Down (1 kΩ to GND) from Zero Scale,
No Load
06803-054
CH1 50mV CH2 5V M4µs A CH2 1.2V
T8.6%
DAC A 200mV p-p
T
A
= 25°C
V
DD
= 5V, V
REF
= 4.096V
SCLK
Figure 43. Glitch Upon Entering Power-Down (1 kΩ to GND) from Zero Scale,
5 kΩ/200 pF Load
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 16 of 28
06803-055
CH1 20mV CH2 5V M4µs A CH2 1.2V
T8.6%
DAC A 129mV p-p
VDD = 5V,VREF = 4.096V
TA = 25°C
SCLK
Figure 44. Glitch Upon Exiting Power-Down (1 kΩ to GND) to Zero Scale,
No Load
06803-056
CH1 20mV CH2 5V M4µs A CH2 1.2V
T8.6%
DAC A 170mV p-p
SCLK
T
A
= 25°C
V
DD
= 5V, V
REF
= 4.096V
Figure 45. Glitch Upon Exiting Power-Down (1 kΩ to GND) to Zero Scale,
5 kΩ/200 pF Load
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 17 of 28
TERMINOLOGY
Relative Accuracy (INL)
For the DAC, relative accuracy, or integral nonlinearity (INL),
is a measure of the maximum deviation in LSBs from a straight
line passing through the endpoints of the DAC transfer function.
Figure 8, Figure 9, and Figure 10 show plots of typical INL vs. code.
Differential Nonlinearity (DNL)
DNL is the difference between the measured change and the
ideal 1 LSB change between any two adjacent codes. A specified
differential nonlinearity of ±1 LSB maximum ensures monoto-
nicity. This DAC is guaranteed monotonic by design. Figure 11,
Figure 12, and Figure 13 show plots of typical DNL vs. code.
Offset Error
Offset error is a measure of the difference between the actual
VOUT and the ideal VOUT, expressed in millivolts in the linear
region of the transfer function. Offset error is calculated using
a reduced code range—AD5064/AD5064-1: Code 512 to Code
65,024; AD5044: Code 128 to Code 16,256; AD5024: Code 32 to
Code 4064, with output unloaded. Offset error can be negative or
positive and is expressed in millivolts.
Gain Error
Gain error is a measure of the span error of the DAC. It is the
deviation in slope of the DAC transfer characteristic from the
ideal, expressed as a percentage of the full-scale range.
Offset Error Temperature Coefficient
Offset error temperature coefficient is a measure of the change
in offset error with a change in temperature. It is expressed in
microvolts per degree Celsius.
Gain Temperature Coefficient
Gain error drift is a measure of the change in gain error with
changes in temperature. It is expressed in parts per million of
full-scale range per degree Celsius.
Full-Scale Error
Full-scale error is a measure of the output error when full-scale
code (0xFFFF) is loaded into the DAC register. Ideally, the
output should be VREF − 1 LSB. Full-scale error is expressed as a
percentage of the full-scale range. Measured with VREF < VDD.
Digital-to-Analog Glitch Impulse
Digital-to-analog glitch impulse is the impulse injected into the
analog output when the input code in the DAC register changes
state. It is normally specified as the area of the glitch in nanovolt-
seconds and is measured when the digital input code is changed
by 1 LSB at the major carry transition (0x7FFF to 0x8000). See
Figure 31.
DC Power Supply Rejection Ratio (PSRR)
PSRR indicates how the output of the DAC is affected by changes
in the supply voltage. PSRR is the ratio of the change in VOUT to
a change in VDD for full-scale output of the DAC. It is measured
in decibels. VREF is held at 2.5 V, and VDD is varied by ±10%.
Measured with VREF < VDD.
DC Crosstalk
DC crosstalk is the dc change in the output level of one DAC in
response to a change in the output of another DAC. It is measured
with a full-scale output change on one DAC (or soft power-down
and power-up) while monitoring another DAC kept at midscale.
It is expressed in microvolts.
DC crosstalk due to load current change is a measure of the
impact that a change in load current on one DAC has to another
DAC kept at midscale. It is expressed in microvolts per milliamp.
Reference Feedthrough
Reference feedthrough is the ratio of the amplitude of the signal
at the DAC output to the reference input when the DAC output
is not being updated (that is, LDAC is high). It is expressed in
decibels.
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into
the analog output of a DAC from the digital input pins of the
device, but it is measured when the DAC is not being written
to (SYNC held high). It is specified in nanovolt-seconds and
measured with one simultaneous data and clock pulse loaded
to the DAC.
Digital Crosstalk
Digital crosstalk is the glitch impulse transferred to the output
of one DAC at midscale in response to a full-scale code change
(all 0s to all 1s or vice versa) in the input register of another
DAC. It is measured in standalone mode and is expressed in
nanovolt-seconds.
Analog Crosstalk
Analog crosstalk is the glitch impulse transferred to the output
of one DAC due to a change in the output of another DAC. It is
measured by loading one of the input registers with a full-scale
code change (all 0s to all 1s or vice versa) while keeping LDAC
high, and then pulsing LDAC low and monitoring the output of
the DAC whose digital code has not changed. The area of the
glitch is expressed in nanovolt-seconds.
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 18 of 28
DAC-to-DAC Crosstalk
DAC-to-DAC crosstalk is the glitch impulse transferred to the
output of one DAC due to a digital code change and subsequent
output change of another DAC. This includes both digital and
analog crosstalk. It is measured by loading one of the DACs
with a full-scale code change (all 0s to all 1s or vice versa) with
LDAC low and monitoring the output of another DAC. The
energy of the glitch is expressed in nanovolt-seconds.
Multiplying Bandwidth
The multiplying bandwidth is a measure of the finite bandwidth
of the amplifiers within the DAC. A sine wave on the reference
(with full-scale code loaded to the DAC) appears on the output.
The multiplying bandwidth, expressed in kilohertz, is the
frequency at which the output amplitude falls to 3 dB below
the input.
Total Harmonic Distortion (THD)
Total harmonic distortion is the difference between an ideal
sine wave and its attenuated version using the DAC. The sine
wave is used as the reference for the DAC, and the THD is a
measure of the harmonics present on the DAC output. It is
measured in decibels.
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 19 of 28
THEORY OF OPERATION
DIGITAL-TO-ANALOG CONVERTER
The AD5024/AD5044/AD5064/AD5064-1 are single 12-/14-/
16-bit, serial input, voltage output DACs with an individual
reference pin. The AD5064-1 model (see the Ordering Guide)
is a 16-bit, serial input, voltage output DAC that is identical to
other AD5064 models but with a single reference pin for all
DACs. The devices operate from supply voltages of 4.5 V to 5.5 V.
Data is written to the AD5024/AD5044/AD5064/AD5064-1 in a
32-bit word format via a 3-wire serial interface. The AD5024/
AD5044/AD5064/AD5064-1 incorporate a power-on reset circuit
that ensures that the DAC output powers up to a known output
state. The devices also have a software power-down mode that
reduces the typical current consumption to typically 400 nA.
Because the input coding to the DAC is straight binary, the ideal
output voltage when using an external reference is given by
N
REFIN
OUT
D
VV
2
where:
D is the decimal equivalent of the binary code that is loaded to
the DAC register (0 to 65,535 for the 16-bit AD5064).
N is the DAC resolution.
DAC ARCHITECTURE
The DAC architecture of the AD5064 consists of two matched
DAC sections. A simplified circuit diagram is shown in Figure 46.
The four MSBs of the 16-bit data word are decoded to drive
15 switches, E1 to E15. Each of these switches connects one of
15 matched resistors to either GND or the VREF buffer output.
The remaining 12 bits of the data-word drive the S0 to S11
switches of a 12-bit voltage mode R-2R ladder network.
2R
S0
VREF
2R
S1
2R
S11
2R
E1
2R
E2
2R
E15
2R
V
OUT
12-BIT R-2R LADDER FOUR MSBs DECODED INTO
15 EQUAL SEGMENTS
06803-006
Figure 46. DAC Ladder Structure
REFERENCE BUFFER
The AD5024/AD5044/AD5064/AD5064-1 operate with an exter-
nal reference. For most models, each DAC has a dedicated voltage
reference pin. The AD5064-1 model has a single voltage reference
pin for all DACs. The reference input pin has an input range of
2.2 V to VDD. This input voltage is then buffered internally to
provide a reference for the DAC core.
OUTPUT AMPLIFIER
The output buffer amplifier can generate rail-to-rail voltages
on its output, which gives an output range of 0 V to VDD. The
amplifier is capable of driving a load of 5 kΩ in parallel with
200 pF to GND. The slew rate is 1.5 V/µs with a ¼ to ¾ scale
settling time of 5.8 µs.
SERIAL INTERFACE
The AD5024/AD5044/AD5064/AD5064-1 have a 3-wire serial
interface (SYNC, SCLK, and DIN) that is compatible with SPI,
QSPI, and MICROWIRE interface standards as well as most
DSPs. See Figure 4 for a timing diagram of a typical write
sequence. The AD5064-1 model contains an SDO pin to allow
the user to daisy-chain multiple devices together (see the Daisy-
Chaining section).
SHIFT REGISTER
The AD5024/AD5044/AD5064/AD5064-1 shift register is 32 bits
wide. The first four bits are dont cares. The next four bits are the
command bits, C3 to C0 (see Table 8), followed by the 4-bit
DAC address bits, A3 to A0 (see Table 9), and finally the bit
data-word. The data-word comprises 12-bit, 14-bit, or 16-bit input
code, followed by eight, six, or four don’t care bits for the AD5024,
AD5044, and AD5064/AD5064-1, respectively (see Figure 47,
Figure 48, and Figure 49). These data bits are transferred to the
DAC register on the 32nd falling edge of SCLK. Commands can be
executed on individually selected DAC channels or on all DACs.
Table 8. Command Definitions
Command
C3 C2 C1 C0 Description
0 0 0 0 Write to Input Register n
0 0 0 1 Update DAC Register n
0 0 1 0 Write to Input Register n, update all
(software LDAC)
0 0 1 1 Write to and update DAC Channel n
0 1 0 0 Power down/power up DAC
0 1 0 1 Load clear code register
0 1 1 0 Load LDAC register
0 1 1 1 Reset (power-on reset)
1 0 0 0 Set up DCEN register1 (daisy-chain enable)
1 0 0 1 Reserved
1 1 1 1 Reserved
1 Available in the AD5064-1 14-lead TSSOP only.
Table 9. Address Commands
Address (n)
Selected DAC Channel
A3 A2 A1 A0
0 0 0 0 DAC A
0 0 0 1 DAC B
0 0 1 0 DAC C
0 0 1 1 DAC D
1 1 1 1 All DACs
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 20 of 28
ADDRESS BITSCOMMAND BITS
C3 C2 C1 C0 A3 A2 A1 A0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X XXXXX
XXXX
DB31 (MSB) DB0 (LSB)
DATA BITS
06803-009
Figure 47. AD5024 Shift Register Content
ADDRESS BITSCOMMAND BITS
C3 C2 C1 C0 A3 A2 A1 A0 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X XXX X
XXXX
DB31 (MSB) DB0 (LSB)
DATA BITS
06803-008
Figure 48. AD5044 Shift Register Content
ADDRESS BITSCOMMAND BITS
C3 C2 C1 C0 A3 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X X
XXXX
DB31 (MSB) DB0 (LSB)
DATA BITS
06803-007
Figure 49. AD5064/AD5064-1 Shift Register Content
SCLK
DIN
DB31 DB0
INVALID WRITE SEQUENCE:
SYNC HIGH BEFORE 32
ND
FALLING EDGE
VALID WRITE SEQUENCE, OUTPUT UPDATES
ON THE 32
ND
FALLING EDGE
DB31 DB0
SYNC
06803-010
Figure 50. SYNC Interrupt Facility
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 21 of 28
MODES OF OPERATION
There are three main modes of operation: standalone mode
where a single device is used, daisy-chain mode for a system
that contains several DACs, and power-down mode when the
supply current falls to 0.4 µA at 5 V.
Standalone Mode
The write sequence begins by bringing the SYNC line low. Data
from the DIN line is clocked into the 32-bit shift register on the
falling edge of SCLK. The serial clock frequency can be as high
as 50 MHz, making the AD5024/AD5044/AD5064/AD5064-1
compatible with high speed DSPs. On the 32nd falling clock edge,
the last data bit is clocked in and the programmed function is
executed, that is, an LDAC-dependent change in DAC register
contents and/or a change in the mode of operation. At this
stage, the SYNC line can be kept low or be brought high. In
either case, it must be brought high for a minimum of 3 µs
(single channel, see Table 4, t8 parameter) before the next write
sequence so that a falling edge of SYNC can initiate the next
write sequence. SYNC should be idled at rails between write
sequences for even lower power operation of the device.
SYNC Interrupt
In a normal write sequence, the SYNC line is kept low for at
least 32 falling edges of SCLK, and the DAC is updated on the
32nd falling edge. However, if SYNC is brought high before the
32nd falling edge, this acts as an interrupt to the write sequence.
The write sequence is seen as invalid. Neither an update of the
DAC register contents nor a change in the operating mode
occurs (see Figure 50).
Daisy-Chaining
For systems that contain several DACs the SDO pin can be
used to daisy-chain several devices together and provide serial
readback.
The daisy-chain mode is enabled through a software executable
daisy-chain enable (DCEN) command. Command 1000 is
reserved for this DCEN function (see Table 8). The daisy-chain
mode is enabled by setting Bit DB1 in the DCEN register. The
default setting is standalone mode, where DB1 = 0.
Table 10 shows how the state of the bit corresponds to the mode
of operation of the device.
Table 10. DCEN (Daisy-Chain Enable) Register
DB1 DB0 Description
0 X Standalone mode (default)
1 X DCEN mode
The SCLK is continuously applied to the shift register when
SYNC is low. If more than 32 clock pulses are applied, the data
ripples out of the shift register and appears on the SDO line.
This data is clocked out on the rising edge of SCLK and is valid
on the falling edge. By connecting this line to the DIN input on
the next DAC in the chain, a daisy-chain interface is constructed.
Each DAC in the system requires 32 clock pulses; therefore, the
total number of clock cycles must equal 32N, where N is the
total number of devices that are updated. If SYNC is taken high
at a clock that is not a multiple of 32, it is considered an invalid
frame and the data is discarded.
When the serial transfer to all devices is complete, SYNC is
taken high. This prevents any further data from being clocked
into the shift register.
In daisy-chain mode, the LDAC pin cannot be tied permanently
low. The LDAC pin must be used in asynchronous LDAC update
mode, as shown in Figure 5. The LDAC pin must be brought
high after pulsing. This allows all DAC outputs to simulta-
neously update.
The serial clock can be continuous or a gated clock. A continuous
SCLK source can be used only if SYNC can be held low for the
correct number of clock cycles. In gated clock mode, a burst
clock containing the exact number of clock cycles must be used,
and SYNC must be taken high after the final clock to latch the data.
Table 11. 32-Bit Shift Register Contents for Daisy-Chain Enable
MSB LSB
DB31 to DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 to DB2 DB1 DB0
X 1 0 0 0 X X X X X 1/0 X
Don’t cares Command bits (C3 to C0) Address bits (A3 to A0) Don’t cares DCEN register
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 22 of 28
POWER-ON RESET
The AD5024/AD5044/AD5064/AD5064-1 contain a power-on
reset circuit that initializes the registers to their default values
and controls the output voltage during power-up. By connecting
the POR pin low, the AD5024/AD5044/AD5064/AD5064-1
output powers up to zero scale. Note that this is outside the
linear region of the DAC; by connecting the POR pin high, the
AD5024/AD5044/AD5064/AD5064-1 output powers up to
midscale. The output remains powered up at this level until a
valid write sequence is made to the DAC. This is useful in
applications where it is important to know the state of the
output of the DAC while it is in the process of powering up.
There is also a software executable reset function that resets the
DAC to the power-on reset code. Command 0111 is designated
for this reset function (see Table 8). Any events on LDAC or
CLR during power-on reset are ignored. The power-on reset
circuit is triggered when VDD passes 2.6 V approximately and
takes 50 µs to complete. No writes to the AD5024/AD5044/
AD5064/AD5064-1 should take place during this time.
To prevent unintended operation during power-up, control the
digital input signals (SYNC, SCLK, DIN, LDAC, and CLR) while
the power supply is ramping. Control these signals by using pull-
up resistors connected to VDD or GND. For applications that do
not require the hardware LDAC or CLR functions, the LDAC pin
and the CLR pin can be tied directly to GND. For applications with
a slow VDD ramp time (for example, more than 2 ms to 3 ms), it is
recommended that a software reset command is written
when the power supplies have reached their final value.
POWER-DOWN MODES
The AD5024/AD5044/AD5064/AD5064-1 contain three
separate power-down modes. Command 0100 is designated for
the power-down function (see Table 8). These power-down
modes are software-programmable by setting two bits, Bit DB9
and Bit DB8, in the shift register. Table 12 shows how the state of
the bits corresponds to the mode of operation of the device.
Table 12. Modes of Operation
DB9 DB8 Operating Mode
0 0 Normal operation
Power-down modes:
0 1 1 kΩ to GND
1 0 100 kΩ to GND
1 1 Three-state
Any or all DACs (DAC D to DAC A) can be powered down to
the selected mode by setting the corresponding four bits (DB3,
DB2, DB1, DB0) to 1. See Table 13 for the contents of the shift
register during power-down/power-up operation.
When both Bit DB9 and Bit D8 in the shift register are set to 0,
the device works normally with its normal power consumption
of 4 mA at 5 V. However, for the three power-down modes, the
supply current falls to 0.4 A at 5 V. Not only does the supply
current fall, but the output stage is also internally switched from
the output of the amplifier to a resistor network of known values.
This has the advantage that the output impedance of the device
is known while the device is in power-down mode. There are
three different power-down options. The output is connected
internally to GND through either a 1 kΩ or a 100 kΩ resistor, or
it is left open-circuited (three-state). The output stage is illustrated
in Figure 51.
RESISTOR
NETWORK
V
OUT
DAC
POWER-DOWN
CIRCUITRY
AMPLIFIER
06803-011
Figure 51. Output Stage During Power-Down
The bias generator, output amplifier, resistor string, and other
associated linear circuitry are shut down when the power-down
mode is activated. However, the contents of the DAC register
are unaffected when in power-down. The DAC register can be
updated while the device is in power-down mode. The time to
exit power-down is typically 4.5 µs for VDD = 5 V (see Figure 30).
Table 13. 32-Bit Shift Register Contents for Power-Up/Power-Down Function
MSB LSB
DB31
to
DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20
DB19
to
DB10 DB9 DB8
DB7
to
DB4 DB3 DB2 DB1 DB0
X 0 1 0 0 X X X X X PD1 PD0 X DAC D DAC C DAC B DAC A
Don’t
cares
Command bits (C3 to C0) Address bits (A3 to A0)—
don’t cares
Don’t
cares
Power-
down mode
Don’t
cares
Power-down/power-up channel
selection—set bit to 1 to select
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 23 of 28
CLEAR CODE REGISTER
The AD5024/AD5044/AD5064/AD5064-1 have a hardware
CLR pin that is an asynchronous clear input. The CLR input is
falling edge sensitive. Bringing the CLR line low clears the
contents of the input register and the DAC registers to the data
contained in the user-configurable CLR register and sets the
analog outputs accordingly (see Table 14). This function can be
used in system calibration or reset to load zero scale, midscale,
or full scale to all channels together. Note that zero scale and full
scale are outside the linear region of the DAC. These clear code
values are user-programmable by setting two bits, Bit DB1 and
Bit DB0, in the shift register (see Table 14). The default setting
clears the outputs to 0 V. Command 0101 is designated for
loading the clear code register (see Table 8).
Table 14. Clear Code Register
DB1 (CR1) DB0 (CR0) Clears to Code
0 0 0x0000
0 1 0x8000
1 0 0xFFFF
1 1 No operation
The device exits clear code mode on the 32nd falling edge of the
next write to the device. If hardware CLR pin is activated
during a write sequence, the write is aborted.
The CLR pulse activation time, which is the falling edge of CLR
to when the output starts to change, is typically 10.6 s. See
Table 16 for contents of the shift register while loading the clear
code register.
LDAC FUNCTION
Hardware LDAC Pin
The outputs of all DACs can be updated simultaneously using
the hardware LDAC pin, as shown in Figure 4. LDAC can be
permanently low or pulsed. There are two methods of using the
hardware LDAC pin, synchronously and asynchronously.
Synchronous LDAC: After new data is read, the DAC registers
are updated on the falling edge of the 32nd SCLK pulse, provided
LDAC is held low.
Asynchronous LDAC: The outputs are not updated at the same
time that the input registers are written to. When LDAC is
pulsed low, the DAC registers are updated with the contents of
the input registers.
Software LDAC Function
Alternatively, the outputs of all DACs can be updated simulta-
neously or individually using the software LDAC function by
writing to Input Register n and updating all DAC registers.
Command 0010 is reserved for this software LDAC function.
Writing to the DAC using Command 0110 loads the 4-bit
LDAC register (DB3 to DB0). The default for each channel
is 0; that is, the LDAC pin works normally. Setting the bits to 1
updates the DAC channel regardless of the state of the hardware
LDAC pin, so that it effectively sees the hardware LDAC pin as
being tied low (see Table 15 for the LDAC register mode of
operation.) This flexibility is useful in applications where the
user wants to simultaneously update select channels while the
remainder of the channels are synchronously updating.
Table 15. LDAC Overwrite Definition
Load LDAC Register
LDAC Bits
(DB3 to DB0) LDAC Pin LDAC Operation
0 1 or 0 Determined by the LDAC pin.
1 X1 DAC channels update, overrides
the LDAC pin. DAC channels see
LDAC as 0.
1 X = don’t care.
The LDAC register gives the user extra flexibility and control
over the hardware LDAC pin (see Table 17). Setting the LDAC
bits (DB0 to DB3) to 0 for a DAC channel means that the update
of this channel is controlled by the hardware LDAC pin.
Table 16. 32-Bit Shift Register Contents for Clear Code Function
MSB LSB
DB31 to DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 to DB2 DB1 DB0
X 0 1 0 1 X X X X X 1/0 1/0
Don’t cares Command bits (C3 to C0) Address bits (A3 to A0) Don’t cares Clear code register
(CR1 to CR0)
Table 17. 32-Bit Shift Register Contents for LDAC Overwrite Function
MSB LSB
DB31 to
DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20
DB19
to DB4 DB3 DB2 DB1 DB0
X 0 1 1 0 X X X X X DAC D DAC C DAC B DAC A
Don’t
cares
Command bits (C3 to C0) Address bits (A3 to A0)—
don’t cares
Don’t
cares
Setting LDAC bits to 1 overrides LDAC pin
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 24 of 28
POWER SUPPLY BYPASSING AND GROUNDING
When accuracy is important in a circuit, it is helpful to carefully
consider the power supply and ground return layout on the board.
The printed circuit board (PCB) containing the AD5024/AD5044/
AD5064/AD5064-1 should have separate analog and digital
sections. If the AD5024/AD5044/AD5064/AD5064-1 are in
a system where other devices require an AGND-to-DGND
connection, the connection should be made at one point only.
This ground point should be as close as possible to the
AD5024/AD5044/AD5064/AD5064-1.
The power supply to the AD5024/AD5044/AD5064/AD5064-1
should be bypassed with 10 µF and 0.1 µF capacitors. The capaci-
tors should be as physically close as possible to the device, with
the 0.1 µF capacitor ideally right up against the device. The 10 µF
capacitors are the tantalum bead type. It is important that the
0.1 µF capacitor have low effective series resistance (ESR) and
low effective series inductance (ESI), such as is typical of common
ceramic types of capacitors. This 0.1 µF capacitor provides a low
impedance path to ground for high frequencies caused by
transient currents due to internal logic switching.
The power supply line should have as large a trace as possible to
provide a low impedance path and reduce glitch effects on the
supply line. Clocks and other fast switching digital signals should
be shielded from other parts of the board by digital ground. Avoid
crossover of digital and analog signals, if possible. When traces
cross on opposite sides of the board, ensure that they run at right
angles to each other to reduce feedthrough effects through the
board. The best board layout technique is the microstrip tech-
nique, where the component side of the board is dedicated to the
ground plane only and the signal traces are placed on the solder
side. However, this is not always possible with a 2-layer board.
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 25 of 28
MICROPROCESSOR INTERFACING
AD5024/AD5044/AD5064/AD5064-1 to Blackfin
ADSP-BF527 Interface
Figure 52 shows a serial interface between the AD5024/
AD5044/AD5064/AD5064-1 and the Blackfin® ADSP-BF527
microprocessor. The ADSP-BF527 processor incorporates two
dual-channel synchronous serial ports, SPORT1 and SPORT0, for
serial and multiprocessor communications. Using SPORT0 to
connect to the AD5024/AD5044/AD5064/AD5064-1, the setup
for the interface is as follows: DT0PRI drives the DIN pin of the
AD5024/AD5044/AD5064/AD5064-1, and TSCLK0 drives the
SCLK of the devices. The SYNC pin is driven from TFS0.
AD5024/
AD5044/
AD5064/
AD5064-1
*
ADSP-BF527*
*ADDITIONAL PINS OMITTED FOR CLARITY.
SYNCTFS0
DINDT0PRI
SCLKTSCLK0
06803-012
Figure 52. AD5024/AD5044/AD5064/AD5064-1 to Blackfin
ADSP-BF527 Interface
AD5024/AD5044/AD5064/AD5064-1 to 68HC11/68L11
Interface
Figure 53 shows a serial interface between the AD5024/AD5044/
AD5064/AD5064-1 and the 68HC11/68L11 microcontroller.
SCK of the 68HC11/68L11 drives the SCLK of the AD5024/
AD5044/AD5064/AD5064-1, and the MOSI output drives the
serial data line of the DAC.
AD5024/
AD5044/
AD5064/
AD5064-1*
68HC11/68L11*
*ADDITIONAL PINS OMITTED FOR CLARITY.
SYNCPC7
SCLKSCK
DINMOSI
06803-013
Figure 53. AD5024/AD5044/AD5064/AD5064-1 to 68HC11/68L11 Interface
The SYNC signal is derived from a port line (PC7). The setup
conditions for correct operation of this interface are as follows:
The 68HC11/68L11 is configured with its CPOL bit as 0, and its
CPHA bit as 1. When data is being transmitted to the DAC, the
SYNC line is taken low (PC7). When the 68HC11/68L11 is
configured as described previously, data appearing on the MOSI
output is valid on the falling edge of SCK. Serial data from the
68HC11/68L11 is transmitted in 8-bit bytes with only eight
falling clock edges occurring in the transmit cycle. Data is
transmitted MSB first. To load data to the AD5024/AD5044/
AD5064, PC7 is left low after the first eight bits are transferred,
and a second serial write operation is performed to the DAC.
PC7 is taken high at the end of this procedure.
AD5024/AD5044/AD5064/AD5064-1 to 80C51/80L51
Interface
Figure 54 shows a serial interface between the AD5024/AD5044/
AD5064/AD5064-1 and the 80C51/80L51 microcontroller. The
setup for the interface is as follows: TxD of the 80C51/80L51
drives SCLK of the AD5024/AD5044/AD5064/AD5064-1, and
RxD drives the serial data line of the device. The SYNC signal is
again derived from a bit-programmable pin on the port. In this
case, Port Line P3.3 is used. When data is to be transmitted to the
AD5024/AD5044/AD5064/AD5064-1, P3.3 is taken low. The
80C51/80L51 transmit data in 8-bit bytes only; thus, only eight
falling clock edges occur in the transmit cycle. To load data to
the DAC, P3.3 is left low after the first eight bits are transmitted,
and a second write cycle is initiated to transmit the second byte of
data. P3.3 is taken high following the completion of this cycle.
The 80C51/80L51 output the serial data in a format that has the
LSB first. The AD5024/AD5044/AD5064/AD5064-1 must
receive data with the MSB first. The 80C51/80L51 transmit
routine should take this into account.
AD5024/
AD5044/
AD5064/
AD5064-1
*
*ADDITIONAL PINS OMITTED FOR CLARITY.
DINRxD
SYNCP3.3
80C51/80L51*
SCLKTxD
06803-014
Figure 54. AD5024/AD5044/AD5064/AD5064-1 to 80C512/80L51 Interface
AD5024/AD5044/AD5064/AD5064-1 to MICROWIRE
Interface
Figure 55 shows an interface between the AD5024/AD5044/
AD5064/AD5064-1 and any MICROWIRE-compatible device.
Serial data is shifted out on the falling edge of the serial clock and is
clocked into the AD5024/AD5044/AD5064/AD5064-1 on the
rising edge of the SCLK.
AD5024/
AD5044/
AD5064/
AD5064-1*
*ADDITIONAL PINS OMITTED FOR CLARITY.
SCLKSO
SYNCCS
MICROWIRE*
DINSK
06803-015
Figure 55. AD5024/AD5044/AD5064/AD5064-1 to MICROWIRE Interface
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 26 of 28
APPLICATIONS INFORMATION
USING A REFERENCE AS A POWER SUPPLY
Because the supply current required by the AD5024/AD5044/
AD5064/AD5064-1 is extremely low, an alternative option is to
use a voltage reference to supply the required voltage to the devices
(see Figure 56). This is especially useful if the power supply is
quite noisy or if the system supply voltages are at some value
other than 5 V (for example, 15 V). The voltage reference outputs
a steady supply voltage for the AD5024/AD5044/AD5064/
AD5064-1. If the low dropout REF195 is used, it must supply
3 mA of current to the AD5024/AD5044/AD5064/AD5064-1,
with no load on the output of the DAC. When the DAC output is
loaded, the REF195 also needs to supply the current to the load.
The total current required (with a 5 kΩ load on the DAC output) is
3 mA + (5 V/5 kΩ) = 4 mA
The load regulation of the REF195 is typically 2 ppm/mA,
which results in a 3 ppm (15 µV) error for the 4 mA current
drawn from it. This corresponds to a 0.196 LSB error.
Figure 56. REF195 as a Power Supply to the AD5024/AD5044/AD5064/AD5064-1
BIPOLAR OPERATION
The AD5024/AD5044/AD5064/AD5064-1 have been designed
for single-supply operation, but a bipolar output range is also
possible using the circuit shown in Figure 57. The circuit gives an
output voltage range of ±5 V. R a i l -to-rail operation at the amplifier
output is achievable using an AD8638 or an AD8639 as the
output amplifier.
Assuming VDD = VREF, the output voltage for any input code can
be calculated as follows:
×
+
×
×= R1
R2
V
R1R2R1D
VV
DDDDOUT
536,65
where D represents the input code in decimal (0 to 65,535).
With VDD = 5 V, R1 = R2 = 10 kΩ,
V
5
536,65
10
×
=D
VOUT
This is an output voltage range of ±5 V, with 0x0000 corre-
sponding to a −5 V output, and 0xFFFF corresponding to a
+5 V output.
06803-017
3-WIRE
SERI AL I NTERF ACE
R2 = 10kΩ
+5V
+5V
AD5024/
AD5044/
AD5064/
AD5064-1
V
DD
V
OUTA
R1 = 10kΩ
±5V
0.1µF
10µF
V
REFA
–5V
5V
V
REF AD8638/
AD8639
Figure 57. Bipolar Operation
USING THE AD5024/AD5044/AD5064/AD5064-1
WITH A GALVANICALLY ISOLATED INTERFACE
In process control applications in industrial environments, it
is often necessary to use a galvanically isolated interface to
protect and isolate the controlling circuitry from any hazardous
common-mode voltages that can occur in the area where the
DAC is functioning. iCoupler® provides isolation in excess of
2.5 k V. T h e AD5024/AD5044/AD5064/AD5064-1 use a 3-wire
serial logic interface, so the ADuM1300 three-channel digital
isolator provides the required isolation (see Figure 58). The
power supply to the device also needs to be isolated, which is
done by using a transformer. On the DAC side of the transformer,
a 5 V regulator provides the 5 V supply required for the
AD5024/AD5044/AD5064/AD5064-1.
0.1µF
GND
DIN
SYNC
SCLK
POWER 10µF
SDI
SCLK
DATA
AD5024/
AD5044/
AD5064/
AD5064-1
V
OUT
x
V
OB
V
OA
V
OC
V
DD
V
IC
V
IB
V
IA
ADuM1300
5V
REGULATOR
06803-018
Figure 58. AD5024/AD5044/AD5064/AD5064-1 with a Galvanically Isolated
Interface
Data Sheet AD5024/AD5044/AD5064
Rev. G | Page 27 of 28
OUTLINE DIMENSIONS
COM PLI ANT T O JEDEC S TANDARDS M O-153-AB- 1
061908-A
4.50
4.40
4.30
14 8
7
1
6.40
BSC
PIN 1
5.10
5.00
4.90
0.65 BSC
0.15
0.05 0.30
0.19
1.20
MAX
1.05
1.00
0.80 0.20
0.09 0.75
0.60
0.45
COPLANARITY
0.10
SEATING
PLANE
Figure 59. 14-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-14)
Dimensions shown in millimeters
16 9
8
1
PIN 1
SEATING
PLANE
4.50
4.40
4.30
6.40
BSC
5.10
5.00
4.90
0.65
BSC
0.15
0.05
1.20
MAX 0.20
0.09 0.75
0.60
0.45
0.30
0.19
COPLANARITY
0.10
COM PLI ANT T O JEDEC S TANDARDS M O-153-AB
Figure 60. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
AD5024/AD5044/AD5064 Data Sheet
Rev. G | Page 28 of 28
ORDERING GUIDE
Model
1
Temperature Range
Accuracy
Resolution
Package Description
Package Option
AD5024BRUZ −40°C to +125°C ±0.5 LSB INL 12 Bits 16-Lead TSSOP RU-16
AD5024BRUZ-REEL7
−40°C to +125°C
±0.5 LSB INL
12 Bits
16-Lead TSSOP
RU-16
AD5044BRUZ −40°C to +125°C ±1 LSB INL 14 Bits 16-Lead TSSOP RU-16
AD5044BRUZ-REEL7 −40°C to +125°C ±1 LSB INL 14 Bits 16-Lead TSSOP RU-16
AD5064ARUZ-1 40°C to +125°C ±4 LSB INL 16 Bits 14-lead TSSOP RU-14
AD5064ARUZ-1REEL7 −40°C to +125°C ±4 LSB INL 16 Bits 14-lead TSSOP RU-14
AD5064BRUZ-1 −40°C to +125°C ±1 LSB INL 16 Bits 14-lead TSSOP RU-14
AD5064BRUZ-1REEL7 −40°C to +125°C ±1 LSB INL 16 Bits 14-lead TSSOP RU-14
AD5064BRUZ −40°C to +125°C ±1 LSB INL 16 Bits 16-Lead TSSOP RU-16
AD5064BRUZ-REEL7 −40°C to +125°C ±1 LSB INL 16 Bits 16-Lead TSSOP RU-16
EVAL-AD5064-1EBZ 14-Lead TSSOP Evaluation Board
EVAL-AD5064EBZ 16-Lead TSSOP Evaluation Board
1 Z = RoHS Compliant Part.
©20082016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06803-0-6/16(G)