Click on Series name for product info on aimtec.com Series AMSR1.5-78-NZ Up to 9.75 Watt | DC-DC Switching Regulator FEATURES: * * * * 3 Pin Sip Package Pin-Out Compatible With LM78XX Linear Regulators Continuous Short Circuit Protection Non-Isolated Regulated Output * * * * Operating Temperature -40C To +85C Wide Input Range Very High Efficiency Up To 93% Low Ripple And Noise Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) Efficiency Vin Max (%) Efficiency Vin Min (%) AMSR1.5-783.3-NZ 4.75-18 3.3 1.5 88 91 AMSR1.5-7805-NZ 6.5-18 5 1.5 91 93 AMSR1.5-783.3L-NZ 4.75-18 3.3 1.5 88 91 AMSR1.5-7805L-NZ 6.5-18 5 1.5 91 93 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Input Specifications Voltage range Filter Quiescent Current Short Circuit consumption Nominal Typical Vin=(LL-HL) at full load Maximum See the table above Capacitor 5 0.5 Units VDC 10 1.8 mA W Maximum Units Output Specifications Output Specifications Voltage accuracy Short Circuit protection Short circuit restart Output current limit Thermal shutdown Dynamic load stability Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Maximum Capacitive Load Conditions Typical 100% load 3 Continuous. Auto recovery % 5 Internal IC junction 10-100% load Vin=(LL-HL) at full load 10-100% load -40C to +85C ambient 20MHz Bandwidth 1000 A C mV % % o %/ C mV p-p F Maximum Units 100 KHz o C o C o C 150 100 0.75 1 0.02 45 General Specifications Input Specifications Switching frequency Operating temperature Storage temperature Max Case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Soldering Temperature www.aimtec.com F 051e R12.H Conditions Typical 100% load With derating above 71C 340 -40 to +85 -55 to +125 Free air convection 95 Non-conductive black plastic (UL94-V0 rated) 4 0.45 X 0.35 X 0.69 inch 11.50 X 8.90 X 17.50 mm > 2 000 000 hrs (MIL-HDBK-217F, Ground Benign, t=+25C) 1.5 mm from case for 10 sec 300 Tel: +1 514 620 2722 1 of 4 % g o C Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR1.5-78-NZ Up to 9.75 Watt | DC-DC Switching Regulator Pin Out Specifications Pin Single 1 2 3 +Vin GND +Vout Footprint Front View 11.50 (0.45 2.54 (0.10) Dimensions 8.90 (0.35) O 1.0 +0.15/-0 (O 0.04 + 0.006/-0 2.54 (0.10) 0.50 (0.024) 17.50 (0.69) Side View 1 2 Dimensions are typical values: mm (inch) General Tolerance: 0.25 ( 0.01) Pin Tolerance: 0.1 ( 0.004) 3 4.10 (0.16) 0.50 (0.024) 0.30 (0.012) 2.54 (0.10) Bottom View 2.15 (0.09) 3.21 (0.13) L Models Footprint 11.5 (0.45) 17.5 (0.69) 4.1 (0.16) 0.5 (0.02) 5.1 (0.2) www.aimtec.com 1.4 (0.05) 9.0 (0.35) Bottom View F 051e R12.H DIV: 2.54 (0.1) 5.1 (0.2) 19.0 (0.75) Side View 1.0 +0.15/-0 ( 0.04 +0.006/-0) Tel: +1 514 620 2722 2 of 4 17.5 (0.69) Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR1.5-78-NZ Up to 9.75 Watt | DC-DC Switching Regulator Derating Free Air Convection 71 C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 20 - 40 0 20 40 60 80 85 100 Ambient Temperature C Typical Application Circuits +Vin C1 10uF GND 3 +Vout 1 AMSR1.5-78-NZ 2 C2 22uF GND C1: A low ESR capacitor is required to keep the noise of the converter to a minimum. Ceramic capacitors are recommended with typical value is 10F / 25V. C2: Installation of C2 is recommended with typical value of 22F / 16V ceramic for 5V and 6.5V output signal and 22F / 6.3V ceramic for 2.5V and 3.3V output signal. NOTE: This part is not designed for parallel operation. www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR1.5-78-NZ Up to 9.75 Watt | DC-DC Switching Regulator Dual Output Connection 3 1 +Vin AMSR1.5-78-NZ C1 10uF +Vout C2 2 22uF GND GND 3 1 AMSR1.5-78-NZ C1 C2 2 22uF 10uF -Vout Input Filter 10uH ~ 47uH 3 +Vout 1 C1 C1 10uF 10uF AMSR1.5-78-NZ 2 C2 22uF GND GND Output Filter 10uH ~ 47uH 3 1 C1 AMSR1.5-78-NZ 10uF GND 2 +Vout C1 C1 10uF 10uF C2 22uF GND NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec's standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.H Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only