18
.267
±.003
SHRINK
TUBE
STRENGTH
MEMBER
.102 ±.001
DIA
CERAMIC
FERRULE
.162
±.004
A DIA
REF
.06240 DIA
+.00002
.00002
ALIGNMENT
SLEEVE**
1.093 ±.020
.080 MAX
CABLE DIA
.040 MAX
BUFFER
CABLE DIA
1.500 MAX*
1.176 MAX*
CERAMIC FERRULE
A DIA
REF
.102 ±.001
DIA
.0625 +.0000
.0002 DIA .297 +.003
.002 STRENGTH
MEMBER
SHRINK TUBE .040 MAX
BUFFER
CABLE DIA
.080 MAX
CABLE DIA
Amphenol® Multi-mode, Size 16 Termini
Features and Performance Levels:
Ceramic alignment ferrule which precisely positions the fiber
within the termini
Phosphor bronze alignment sleeve, assembled on the socket
after polishing insures accurate fiber to fiber alignment (a
ceramic alignment sleeve is also available).
Typical insertion loss for 100/140 fiber with .2 NA at 820 nm
is .5 to .7 dB using Air Gap (AG) polish technique
Use of the ceramic ferrule and sleeve maximizes the ability to
hold extremely tight dimensional tolerances while maintaining
accurate concentricity, thus providing superior and consistent
optical loss performance.
Termination accomplished using the industry proven epoxy/
polish method. Can be polished Air Gap (AG) or Physical con-
tact (PC).
Socket cleaning optional. Consult Amphenol, Sidney, NY for
termini cleaning tool. For application tools consult Sidney, NY. Multi-mode Size 16 Fiber Optic Termini
Amphe-Lite Series
fiber optic termini multi-mode, size 16
Size 16 Multi-mode
Pin Terminus
Size 16 Multi-mode
Socket Terminus
* Indicated dimension when fully assembled.
** Alignment sleeve shipped unassembled.
Amphenol® Multi-Channel fiber optic connectors are supplied less contacts. Order multi-mode
termini by Amphenol part number designation as shown in the chart below. Consult Amphe-
nol, Sidney, NY for further availability.
Additional sizes available upon request: consult Amphenol, Sidney, NY
for availability.
Power contacts can be purchased separately, contact Amphenol, Sidney, NY.
Ordering Information
Multi-mode Termini (Size 16) for Amphe-Lite Connectors
Fiber Size
Core/Cladding Dia (Microns) Size 16 Socket Size 16 Pin A Dia Ref
Inches Microns
50/125 CF-198035-010 CF-198036-010 .0050 127
62.5/125
100/140 CF-198035-017 CF-198036-017 .0057 145
100/140/172 CF-198035-029 CF-198036-029 .0069 175
100/140/172 CF-198035-29A CF-198036-29A .0068 173.5
200/230 CF-198035-053 CF-198036-053 .0093 236
200/240 CF-198035-057 CF-198036-057 .0097 245
200/280 CF-198035-074 CF-198036-074 .0114 290
200/300 CF-198035-080 CF-198036-080 .0120 305
STAINLESS
STEEL BODY
SPRING
SOCKET
PHOSPHOR BRONZE
ALIGNMENT SLEEVE
CERAMIC
FERRULE
STAINLESS STEEL
BODY
PIN
CERAMIC FERRULE
19
.263 ±.004
.03937 +.00012
.00000 DIA
ALIGNMENT
SLEEVE**
A DIA
REF
CERAMIC
FERRULE
.162 ±.002
1.500 MAX*
.069 ±.001
DIA
1.093 ±.020
STRENGTH
MEMBER
SHRINK TUBE
.037 MAX BUFFER
CABLE DIA
.063 MAX
CABLE DIA
.123 MIN
+.00012
.03937 .00000 DIA
.069 ±.001
DIA A DIA
REF
CERAMIC
FERRULE
1.176 MAX*
SHRINK TUBE .037 MAX BUFFER
CABLE DIA
.063 MAX
CABLE DIA
STRENGTH
MEMBER
.297 +.003
.002
Amphenol® Multi-mode, Size 20 Termini
Features and Performance Levels:
Designed for use in size 20 cavities of Amphe-Lite connectors
Designed with similar high performance components as the
proven size 16 termini
Comparable performance and reliability to the size 16 termini
can be expected
Offers increased termini density in Amphenol Amphe-Lite con-
nectors
Maintains fiber optic/electrical hybrid capabilities
Allows for multiple fiber accommodations
Termination accomplished using the industry proven epoxy/
polish method. Can be polished Air Gap (AG) or Physical con-
tact (PC).
Socket cleaning optional. Consult Amphenol, Sidney, NY for
termini cleaning tool. For application tools consult Sidney, NY.
Amphe-Lite Series
fiber optic termini multi-mode, size 20
Amphenol® Multi-Channel fiber optic connectors are supplied less contacts. Order
multi-mode termini by Amphenol part number designation as shown in the chart
below. Consult Amphenol, Sidney, NY for further availability.
Additional sizes available upon request: consult Sidney, NY for availability.
Power contacts can be purchased separately, contact Sidney, NY.
Ordering Information
Multi-mode Termini (Size 16) for Amphe-Lite Connectors
Fiber Size
Core/Cladding Dia (Microns) Size 20 Socket Size 20 Pin A Dia Ref
Inches Microns
50/125 CF-198080-010 CF-198081-010 0.0050 127
62.5/125
100/140 CF-198080-017 CF-198081-017 0.0057 145
Multi-mode Size 20 Fiber Optic Termini
* Indicated dimension when fully assembled.
** Alignment sleeve shipped unassembled.
Size 20 Multi-mode
Pin Terminus
Size 20 Multi-mode
Socket Terminus
CERAMIC FERRULE
PHOSPHOR BRONZE
ALIGNMENT SLEEVE
SPRING
STAINLESS
STEEL BODY
SOCKET
PIN
CERAMIC
FERRULE
STAINLESS STEEL
BODY
20
DIA.
.297 +.003
.002
.102 ±.001
A DIA.
REF. CERAMIC
FERRULE
C REF
SHRINK
TUBE
.500 RADIUS
B MAX
.128 +.002
.001
DIA..0625 +.0000
.0002
.675 MAX.
1.093 ±.020
.500 RADIUS
REF.
.557 ±.008
.537 REF.
1.145 MAX.
.128
DIA.
+.002
.001
.102 ±.001 DIA.
SHRINK TUBING***
1.100
REF.
1.820 MAX.**
A DIA. REF.
.06240 ±.00002
.162
±.004 CERAMIC
FERRULE
ALIGNMENT
SLEEVE***
.267 +.003
.002
Amphenol provides 90°, size 16 fiber optic termini that can be used with multi-channel cylindrical connectors.
90° Socket Termini (Size 16)
90° Pin Termini (Size 16)
Ordering Information for 90° Multi-mode Socket Termini
Fiber Size
Core/Cladding
Dia (Microns)
Socket, Size 16
Amphenol Part Number
For use in Cylindrical
Connectors
A Dia Ref
Inches Microns
50/125 CF-198111-010 .0050 127
62.5/125
100/140 CF-198111-017 .0057 145
100/140/172 CF-198111-29 OR .0069 175
CF-198111-29A .0068 173.5
Additional sizes available upon request: consult
Amphenol, Sidney, NY for availability.
* Consult Amphenol, Sidney, NY for ordering
information.
** Indicated dimension when fully
assembled.
*** Shrink tubing and alignment sleeve
are shipped unassembled.
Additional sizes available upon request: consult Amphenol,
Sidney, NY for availability.
* Consult Amphenol, Sidney, NY for ordering information.
Ordering Information for 90° Multi-mode Pin Termini
Fiber Size
Core/Cladding
Dia (Microns)
Pin, Size 16
Amphenol Part Number
For use in Cylindrical
Connectors
A Dia Ref B Max
(Inches)
C Ref
(Inches)
Inches Microns
50/125 CF-198110-010 .0050 127 1.121 1.100
62.5/125
100/140 CF-198110-017 .0057 145 1.121 1.100
100/140/172 CF-198110-029 OR .0069 175 1.121 1.100
CF-198110-29A .0068 173.5 1.121 1.100
50/125 CF-198112-010 .0050 127 1.003 .900
62.5/125
100/140 CF-198112-017 .0057 145 1.003 .900
100/140/172 CF-198112-029 OR .0069 175 1.003 .900
CF-198112-29A .0068 173.5 1.003 .900
Amphe-Lite Series
fiber optic termini 90° multi-mode, size 16
21
Amphe-Lite Series
application tools
Contact
Size/Type
Crimping
Tool
Turret Die
or Positioner
12 Pin and Socket M22520/1-01 M22520/1-04
16 Pin and Socket M22520/1-01
M22520/7-01
M22520/1-04
M22520/7-04
20 Pin and Socket
M22520/1-01
M22520/2-01
M22520/7-01
M22520/1-04
M22520/2-10
M22520/7-08
22D Pin M22520/2-01
M22520/7-01
M22520/2-09
M22520/7-07
22D Socket M22520/2-01
M22520/7-01
M22520/2-07
M22520/7-05
8 Twinax Center
Pin and Socket M22520/2-01 M22520/2-37
8 Twinax Intermediate
Outer Pin & Socket M22520/5-01 M22520/5-200
The following data includes information pertaining to the application tools which have been estab-
lished for crimping, inserting, and removing contacts incorporated in the Amphe-Lite Series con-
nectors. For additional information on coaxial contact tools see catalog 12-130.
All crimping tools included are the full cycling type.
There is a possibility of additional crimping tools other than those included being available at
present or in the future for this specific application.
RECOMMENDED CRIMPING TOOLS
Contact
Size/Type
Crimping
Tool
Turret Die
or Positioner
8 Coaxial Inner
Pin and Socket M22520/2-01 M22520/2-31
8 Coaxial Outer Pin
and Socket
M22520/5-01 M22520/5-05
Die Closure B
M22520/5-01 M22520/5-41
Die Closure B
M22520/10-01 M22520/10-07
Die Closure B
16 Coaxial Inner
Pin and Socket M22520/2-01 M22520/2-35
16 Coaxial Outer
Pin and Socket M22520/4-01 M22520/4-02
12 Coaxial Inner
Pin and Socket M22520/2-01 M22520/2-34
12 Coaxial Outer
Pin and Socket M22520/31-01 M22520/31-02
10 (Power) TP201423 1716P-1
Where 2 or 3 tools are listed for a contact size, only one tool and its die or positioner are
required to crimp the contact.
The above crimping tools and positioners are available from the approved tool manufacturer.
INSERTION TOOLS
Use with
Contact
Size
Plastic Tools Metal Tools
MS
Part Number Color
Angle Type Straight Type
Proprietary
Part Number Color
MS
Part Number
Proprietary
Part Number
10 (Power) M81969/14-05* Gray / (White) M81969/8-11 ††Green
12 M81969/14-04* Yellow / (White) M81969/8-09 11-8674-12 11-8794-12 Yellow
16 M81969/14-03* Blue / (White) M81969/8-07 11-8674-16 11-8794-16 Blue
20 M81969/14-10* Red / (Orange) M81969/8-05 11-8674-20 11-8794-20 Red
22D M81969/14-01* Green / (White) M81969/8-01 11-8674-24 11-8794-24 Black
8 Coaxial None Required
8 Twinax None M81969/46-06** None Red
REMOVAL TOOLS
Use with
Contact
Size
Plastic Tools Metal Tools
MS
Part Number Color
For Unwired
Contacts
Proprietary
Part Number
Angle Type
Straight Type
Proprietary
Part Number Color
MS
Part Number
Proprietary
Part Number
10 (Power) M81969/14-05* (Gray) / White M81969/8-12 ††Green / White
12 M81969/14-04* (Yellow) / White 11-10050-11 M81969/8-10 11-8675-12 11-8795-12 Yellow / White
16 M81969/14-03* (Blue) / White 11-10050-10 M81969/8-08 11-8675-16 11-8795-16 Blue / White
20 M81969/14-10* (Orange)/ Red 11-10050-9 M81969/8-06 11-8675-20 11-8795-20 Red / White
22D M81969/14-01* (Green) / White 11-10050-7 M81969/8-02 11-8675-24 11-8795-24 Green / White
8 Coaxial M81969/14-12 Green None None 11-9170 DRK264-8†† N/A
8 Twinax M81969/14-12 Green None M81969/46-12** 11-9170 N/A N/A
The M81969/8, 11-8674, 11-8675,and 11-8794 metal contact insertion and removal tools will accommodate wires having the maximum outside diameter as fol-
lows: Contact size 12 .155, 16 .109, 20 .077, 22D .050. When wire diameters exceed those specified, the plastic tools must be used.
* Double end insertion/removal tool.
** Twinax insertion tools are available only in a straight type, metal version..
To be determined.
†† Contact Daniels Manufacturing Co. for availability.
22
Amphenol® Amphe-Lite Composite Connectors can be ordered by coded part number.
Ordering procedure is illustrated by part number AL00F9-35PB as shown below:
AL 00 F 9 - 35 P B ( )
Connector Type
Shell Style
Service Class
Shell Size
Insert Arrangement
Contact Type
Alternate Positions
Specials
Amphe-Lite Series
how to order
Connector Type
AL designates Amphe-Lite Connector Series
Shell Style
00 designates wall mount receptacle
06 designates straight plug
07 designates jam nut receptacle
Service Class
F electroless nickel plated composite
U black composite, unplated
X black zinc alloy, conductive, composite
Shell Size
9 thru 25 available
Insert Arrangement
See insert arrangement chart, page 3. See insert configurations illustrated on pages 5-8.
Contact Type
P designates standard 500 cycle pin contacts
S designates standard 500 cycle socket contacts
Alternate Positions
Locksmith keying - rotation of minor keys. N not required for normal position, see page 4.
Specials
Specials include optional contact styles and contact platings. Also includes a high decou-
pling style of Amphe-Lite. Consult Amphenol, Sidney, NY for part numbering suffix for spe-
cials.
Standard Packaging
The Amphe-Lite Series is shipped with connectors and contacts packaged in bulk. Consult
Amphenol, Sidney NY for special packaging requirements
23
Amphe-Lite – capabilities
fiber optics, filter contacts, flex termination,
coax contacts
FIBER OPTIC
Fiber optic termini connectors offer a precision optic interconnect
system within the Amphe-Lite connector. The Amphe-Lite connec-
tor provides protection from damage in severe environmental and
physical conditions. Optical performance is optimized utilizing the
ceramic alignment features employed by the termini. Insertion
losses are typically .8dB and can range from .5 to 1.5 dB, depend-
ing on test conditions.
See pages 18-20 for fiber optic termini features and how to order.
Ask for publication 12-352 or contact Sidney, NY for more informa-
tion on Amphenol Fiber Optic Connectors.
Also available with MT and LC termination within an Amphe-Lite
shell kit. Contact Amphenol, Sidney for more information.
FILTER CONTACTS FOR EMI PROTECTION
EMI shielding protection devices can be integrated into the Amphe-Lite connector
to provide a cost effective alternative to discrete devices mounted inside the box.
These unique, high performance designs provide weight and space savings neces-
sary for modern electronic systems.
Ask for publication 12-120 or contact Amphenol, Sidney, NY for complete informa-
tion on Amphenol Filter/Transient Protection Connectors.
FLEX TERMINATION ASSEMBLIES FOR
PRINTED CIRCUIT BOARD APPLICATIONS
Amphenol provides flex termination assemblies for printed circuit board attachment. Flex
circuits are available for Amphe-Lite connectors in flat or sculptured styles. Sculptured®
Flexible Circuits with built-in terminations eliminate the failures associated with crimped or
solder-on contacts, and they are designed to geometrically fit the tight space requirements
within a unit. They plug into a printed circuit board and create a self-locking terminal pad
which eliminates the need for an additional interconnect to the PCB.
Ask for catalog 12-170, Amphenol Cylindrical
Connectors for PCB Applications.
CONNECTORS WITH COAX CONTACTS
For shielded wire applications, coaxial con-
tacts can be incorporated into Amphe-Lite
connectors. Designed-in crimp or solder types
are available to fit various RG and special
cables. High performance coaxial contacts
eliminate discontinuities or impedance varia-
tions due to movement of parts under axial
load.
For further information on coax contacts ask
for catalog 12-130.
Fiber Optics
Filter Contacts
Flex Termination Assemblies
Coax Contacts