CSM_ZAP_DS_E_3_1
1
Pushbutton Switch (Cylindrical 30-dia.)
ZAP
Long Service Life with Built-in Z-series
Basic Switch
• Using a Basic Switch enables direct switching of large-capacity
loads
• Shock-absorbing construction of Operation Unit protects the Switch
• Drip-proof Pushbutton construction enables use in locations subject to
splashing water and oil and scattering dust.
• Pushbuttons are available in three shapes and six colors.
Refer to Safety Precautions for All Pushbutton Switches
and Safety Precautions on page 3.
Ordering Information
Note: Models with special specifications are available for use in environments with high humidity or outdoors.
Contact your OMRON representative for information.
Specifications
Ratings
Note: 1. The above values are for steady-state currents.
2. Inductive load: Power factor = 0.4 (AC); time constant = 7 ms (DC).
3. The lamp load has an inrush current of 10 times the steady-state current.
4. The motor load has an inrush current of 6 times the steady-state current.
5. Standard testing condition.
(1) Ambient temperature: 20 ±2°C
(2) Ambient humidity: 65% ±5%RH
(3) Operating frequency: 20 times/min
Classification Shape of Operation
Unit Output Operation Unit color
Blue (-A) Black (-B) Green (-G) Red (-R) White (-W) Yellow (-Y)
Momentary
operation
1ZAP-A ZAP-B ZAP-G ZAP-R ZAP-W ZAP-Y
22ZAP-A 2ZAP-B 2ZAP-G 2ZAP-R 2ZAP-W 2ZAP-Y
1ZAP-1A ZAP-1B ZAP-1G ZAP-1R ZAP-1W ZAP-1Y
22ZAP-1A 2ZAP-1B 2ZAP-1G 2ZAP-1R 2ZAP-1W 2ZAP-1Y
1ZAP-2A ZAP-2B ZAP-2G ZAP-2R ZAP-2W ZAP-2Y
22ZAP-2A 2ZAP-2B 2ZAP-2G 2ZAP-2R 2ZAP-2W 2ZAP-2Y
Item
Built-in Switch
Rated voltage (V)
Non-inductive load (A) Inductive load (A)
Resistive load Lamp load Inductive load Motor load
NC NO NC NO NC NO NC NO
Z-15G5-B
125 VAC
200 VAC
500 VAC
15
15
10
3
2.5
1.5
1.5
1.25
0.75
15
15
6
15
3
1.5
2.5
1.5
0.75
8 VDC
14 VDC
30 VDC
125 VDC
250 VDC
15
15
6
0.5
0.25
3
3
3
0.5
0.25
1.5
1.5
1.5
0.5
0.25
15
10
5
0.05
0.03
5
5
5
0.05
0.03
2.5
2.5
2.5
0.05
0.03
36 dia. 25 dia.
36 dia. 25 dia.
40 dia.
ZAP
2
Specifications
Characteristics Operating Characteristics
Contact Form
Approved Safety Standards
•The built-in Z-15G5-B Switch is approved for UL and CSA.
Dimensions
Insert one of the following letters into the box (
@
) at the end of the model number. Refer to Ordering Information for color symbols. (Unit: mm)
Operat-
ing fre-
quency
Mechanical 60 operations/min
Electrical 20 operations/min
Insulation resistance 100 MΩ min. (at 500 VDC)
Contact resistance 30 mΩ max. (initial value)
Dielectric
strength
Between terminals of same
polarity 1,000 VAC, 50/60 Hz for 1 min
Between current-carrying metal part
and ground, and between each termi-
nal and non-current-carrying metal part
2,000 VAC, 50/60 Hz for
1 minute
Vibra-
tion re-
sistance
Malfunction 10 to 55 Hz, 1.5-mm double
amplitude (1 ms max.)
Shock re-
sistance
Destruction 500 m/s2
Malfunction 200 m/s2 max. (1 ms max.)
Durabili-
ty
Mechanical 1,000,000 operations min.
Electrical 500,000 operations min.
Weight Approx. 130 to 210 g
Inrush
current
NC 30 A max.
NO 15 A max.
Ambient operating temperature −25 to 80°C (with no icing or
condensation)
Ambient operating humidity 35% to 85%RH
Ambient storage temperature −25 to 80°C (with no icing or
condensation)
Degree of protection IP65 (Operation Unit only)
Electric shock protection class Class II
PTI (proof tracking index) 175
Pollution degree 3 (IEC947-5-1)
Model
Operating characteristics ZAP-@@ 2ZAP-@@
Operating force OF Approx. 9.81 N Approx. 14.7 N
Name Contact form
Double-throw contacts COM
NC
NO
26
25 dia.
26
19
40 dia.
9.75
24.6
43.5
2ZAP-@ZAP-@
25 dia.
24.6
37
36 dia. 49.2 52
10.8 t
*
51.8 max.
Washer
Mounting panel thickness:
1.6 to 6 mm
Rubber packing Z-15G5-B Basic Switch
Three, M4 ✕ 5.5
Terminal screws
(with toothed washer)
* Chromed plating
ZAP-@
2ZAP-@
25 dia.
15.8
36 dia.
t
*Mounting panel thickness:
1.6 to 6 mm
* Chromed plating
ZAP-1@
2ZAP-1@
40 dia.
t
27.6
36 dia.
*
* Chromed plating
Mounting panel thickness:
1.6 to 6 mm
ZAP-2@
2ZAP-2@
ZAP
3
Dimensions (Unit: mm)
Panel Cutouts Accessories
Rubber Cap
•Use the special rubber cap to use the Switch in locations subject to
significant splashing water and oil or scattering dust.
Cannot be used, however, with the (2) ZAP-2.
Safety Precautions
Refer to Safety Precautions for All Pushbutton Switches.
Insulation
•After wiring the Switch, ensure an appropriate insulating distance.
Wiring
•Tighten the terminal screws to a torque of 0.78 to 1.18 N·m.
Mounting
•Tighten the face nut to a torque of 0.98 to 1.76 N·m.
•For panel mounting, always use a washer (or a nameplate) and
rubber packing.
15
5.2 dia.
30.5
±
0.3
dia. hole
Color Model
Blue (-A) ZB-A
Black (-B) ZB-B
Green (-G) ZB-G
Red (-R) ZB-R
White (-W) ZB-W
Yellow (-Y) ZB-Y
Precautions for Correct Use
Washer
(or nameplate)
Rubber packing
Mounting panel
t = 1.6 to 6 mm
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or government regulations.
Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
2011.8
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2011 All Right Reserved.
