June 2008 TLE4946-2L High Precision Hall Effect Latch TLE4946-2L Datasheet Rev 1.0 Sensors Edition 2008-06 Published by Infineon Technologies AG 81726 Munchen, Germany (c) 2007 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. TLE4946-2L TLE4946-2L High Precision Hall Effect Latch Revision History: 2008-06, Rev 1.0 Previous Version: Page Subjects (major changes since last revision) We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: sensors@infineon.com Datasheet 3 Rev 1.0, 2008-06 TLE4946-2L 1 1.1 1.2 1.3 Product Description 5 Overview 5 Features 5 Target Applications 5 2 2.1 2.2 2.3 2.4 2.5 2.6 Functional Description 5 General 5 Pin Configuration 6 Pin Description 6 Block Diagram 6 Operating Modes and States 7 Functional Block Description 7 3 3.1 3.2 3.3 3.4 Specification 8 Application Circuit 8 Absolute Maximum Ratings 8 Operating Range 9 Characteristics 9 4 4.1 Package Information 10 Package Outline 10 Datasheet 4 Rev 1.0, 2008-06 High Precision Hall Effect Latch 1 Product Description 1.1 Overview TLE4946-2L The TLE4946-2L is a high precision Hall effect latch with highly accurate switching thresholds for operating temperatures up to 150C. 1.2 * * * * * * * * * * Features 2.7 V to 18 V supply voltage operation Operation from unregulated power supply High sensitivity and high stability of the magnetic switching points High resistance to mechanical stress by active error compensation Reverse battery protection (Vs = -18V) Superior temperature stability Peak temperatures up to 195C without damage Low jitter (typ. 1s) High ESD performance ( 4 kV HBM) Digital output signal 1.3 Target Applications The TLE4946-2L is an integrated circuit Hall-effect sensor with low switching thresholds and low hysteresis. It is specially designed for high sensitivity applications and is ideally suited to detect the rotor position in a BLDC motor. Also for index counting with small pole wheels and large air gaps the sensor provides a reliable switching information. 2 Functional Description 2.1 General Precise magnetic switching thresholds and high temperature stability are achieved by active compensation circuits and chopper techniques on chip. Offset voltages, generated by temperature induced stress or overmolding are canceled and high accuracy is achieved. The IC has an open collector output stage with 20mA current sink capability. A wide operating voltage range form 2.7V to 18V with reverse polarity protection up to -18V makes the device suitable for a wide range of applications. A magnetic south pole with field strength above Bop turns the output on and a magnetic north pole exceeding Brp turns it off. Product Name Product Type Ordering Code Package Hall Effect Latch TLE4946-2L SP000398352 PG-SSO-3-2 Datasheet 5 Rev 1.0, 2008-06 TLE4946-2L Functional Description 2.2 Pin Configuration Center of Sensitive Area 2.08 0.1 1.35 0.1 1 2 3 PG-SSO-3-2 Figure 1 Pin Configuration and sensitive area (Top View, Figure not to Scale) 2.3 Pin Description Table 1 Pin Description Pin or Ball No. Name Pin Type Function 1 Vs I Supply voltage 2 GND O Ground 3 Q O Output 2.4 Comments Block Diagram VS Voltage Regulator reverse polarity protected Bias and Compensation Circuits Oscillator and Sequencer Q Ref Amplifier Chopped Hall Probe Figure 2 Datasheet Low Pass Filter Comparator with Hysteresis GND TLE4946-2L Block Diagram 6 Rev 1.0, 2008-06 TLE4946-2L Functional Description 2.5 Operating Modes and States Field Direction Definition: Positive magnetic fields are related with the south pole of the magnet to the branded side of package. B OP Applied Magnetic Field B RP td td tf VQ tr 90% 10% Figure 3 Timing diagram VQ B B rp 0 Figure 4 Output Signal 2.6 Functional Block Description Bop The chopped Hall IC switch comprises a Hall probe, bias generator, compensation circuits, oscillator and output transistor. The bias generator provides currents for the Hall probe and the active circuits. Compensation circuits stabilize the temperature behavior and reduce technology variations. The Active Error Compensation rejects offsets in signal stages and the influence of mechanical stress to the Hall probe caused by molding and soldering processes and other thermal stresses in the package. This chopper technique together with the threshold generator and the comparator ensure high accurate magnetic switching points Datasheet 7 Rev 1.0, 2008-06 TLE4946-2L Specification Figure 5 Q Q GND VS GND 1.2k Application Circuit 4.7nF 3.1 4.7nF Specification TLE4946-2L 3 200 VS Application circuit It is recommended to use a serial resistor of 200 in the supply line for current limitation in the case of a overvoltage pulse. Two capacitors of 4.7nF enhance the EMC performance. The pull-up resistor of 1.2k limits the current through the output transistor. 3.2 Absolute Maximum Ratings Table 2 Absolute Maximum Ratings Parameter Symbol Values Unit Note/Test Condition Min. Typ. Max. -40 - 150 - - 155 for 2000 h (not additive) - - 165 for 1000 h (not additive - - 175 for 168 h (not additive) - - 195 for 3 x 1 h (additive) VDD -18 -18 -18 - - - 18 24 26 V Supply current through protection device IS - 50 - + 50 mA Output voltage VQ -0.7 - 18 V -0.7 - 26 - 40 - 150 C - unlimited mT Max. junction temperature Supply voltage TJ Storage temperature TS Magnetic flux density B ESD robustness HBM: 1.5 k, 100 pF VESD,HBM Datasheet 4 C for 1h, Rs 200 for 5min, Rs 200 for 5min @ 1.2k pull up kV 8 According to EIA/JESD22-A114-B Rev 1.0, 2008-06 TLE4946-2L Specification Attention: Stresses above the max. values listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. 3.3 Operating Range The following operating conditions must not be exceeded in order to ensure correct operation of the TLE4946-2L. All parameters specified in the following sections refer to these operating conditions unless otherwise mentioned. Table 3 Operating Range Parameter Symbol Values Unit Min. Typ. Max. Supply voltage VS 2.7 - 18 V Output voltage VQ - 0.7 - 18 V Junction temperature Tj - 40 - 150 C Output current IQ 0 - 20 mA 3.4 Note/ Test Condition Characteristics Product characteristics involve the spread of values guaranteed within the specified voltage and ambient temperature range. Typical characteristics are the median of the production (at Vs = 12V and TA= 25C). Table 4 Electrical Characteristics Parameter Symbol Values Min. Typ. Max. Unit Note/ Test Condition Supply current IS 2 4 6 mA VS = 2.7 V ... 18 V Reverse current ISR 0 0.2 1 mA VS = - 18 V Output saturation voltage VQSAT - 0.3 0.6 V IQ = 20 mA Output leakage current IQLEAK - 0.05 10 A for VQ = 18 V Output fall time tf - 0.02 1 s Output rise time tr - 0.4 1 s RL = 1.2 k; CL = 50 pF Chopper frequency fOSC - 320 - Switching frequency Delay time 2) Output jitter 3) Power-on time 4) Thermal resistance 5) kHz 1) fSW 0 - 15 kHz td - 13 - s tQJ - 1 - sRMS Typ. value for square wave signal 1 kHz tPON - 13 - s VS 2.7 V RthJA - 190 K/W PG-SSO-3-2 1) To operate the sensor at the max. switching frequency, the value of the magnetic signal amplitude must be 1.4 times higher than for static fields. This is due to the - 3 dB corner frequency of the low pass filter in the signal path. 2) Systematic delay between magnetic threshold reached and output switching 3) Jitter is the unpredictable deviation of the output switching delay 4) Time from applying VS 2.7 V to the sensor until the output state is valid 5) Thermal resistance from junction to ambient Datasheet 9 Rev 1.0, 2008-06 TLE4946-2L Package Information Table 5 Magnetic Characteristics Parameter Symbol Values Unit Min. Typ. Max. Operate point BOP 0.5 2.0 3.5 mT Release point BRP BHYS -3.5 -2.0 -0.5 mT 1.0 4 6.0 mT BOFF -1.5 0 1.5 mT Hysteresis 1) Magnetic Offset Temperature compensation of magn. thresholds TC -350 ppm/C Repeatability of magnetic thresholds 2) BREP 20 TRMS Note/ Test Condition 1) Boff = (Bop + Brp)/2 2) BREP is equivalent to the noise constant 4 Package Information 4.1 Package Outline 46 2 yww S d Year (y) = 0...9 Calendar Week (ww) = 01...52 Branded Side Hall-Probe d : Distance chip to upper side of IC PG-SSO-3-2 : 0.57 0.08 mm AEA03644 AEA02510-1 Figure 6 Datasheet Marking of TLE4946-2L and Distance of chip to upper side of IC 10 Rev 1.0, 2008-06 TLE4946-2L Package Information 0.8 0.1 x 45 7 0.2 2 A 1.52 0.05 1 MAX.1) 7 0.35 0.1 x 45 3.29 0.08 3 0.06 4.06 0.08 1.9 MAX. (0.25) 0.15 MAX. 4.16 0.05 (0.79) 0.6 MAX. 0.2 +0.1 0.4 0.05 1.270.25 1 2 3 1.270.25 18 0.5 6 0.5 1-1 38 MAX. 9 +0.75 -0.5 23.8 0.5 12.7 1 A Adhesive Tape Tape 6.35 0.4 1) No solder function area Figure 7 Datasheet 4 0.3 12.7 0.3 Total tolerance at 10 pitches 1 0.25 -0.15 0.39 0.1 GPO05358 Package outline 11 Rev 1.0, 2008-06 www.infineon.com Published by Infineon Technologies AG Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Infineon: TLE4946-2L TLE4946-1L TLE49462LHALA1