https://www.phoenixcontact.com/us/products/1019517
03/23/2021Page1/4
Flush-type connector-SACC-E-MS-4CON-M16/0,5-18AWG-1019517
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
Key Commercial Data
Packing unit 1 pc
Minimum order quantity 100 pc
GTIN
GTIN 4055626514765
Weight per Piece (excluding packing) 40.000 g
Custom tariff number 85444290
Country of origin Germany
Technical data
Dimensions
Fixed cable length 0.5
Ambient conditions
Ambient temperature (operation) -25 ... -85
General
Standards/regulations according to IEC61076-2-101
Insertion/withdrawal cycles > 100
Overvoltage category II
Mounting type Front wall/screw mounting
Coding A-coded
Thread type M16 x 1.5
Cable cross section 0.75
Rated surge voltage 2.5 kV AC
Degree of pollution 3
Degree of protection IP67
Number of positions 4
https://www.phoenixcontact.com/us/products/1019517
03/23/2021Page2/4
Flush-type connector-SACC-E-MS-4CON-M16/0,5-18AWG-1019517
Technical data
General
Current 4 A
Voltage 250 V
Connection data
Connection method Individual wires
Standards and Regulations
Standards/specifications according to IEC61076-2-101
Safety note
WARNING: The connectors may not be plugged in or disconnected under
load. Ignoring the warning or improper use may damage persons and/or
property.
• WARNING: Commission properly functioning products only. The products
must be regularly inspected for damage. Decommission defective products
immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate
the product. They must observe the following safety notes. The qualified
personnel must be familiar with the basics of electrical engineering. They
must be able to recognize and prevent danger. The relevant symbol on the
packaging indicates that only personnel familiar with electrical engineering
are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and
electrical device engineering.
• When operating the connectors in outdoor applications, they must be
separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the
standards listed (e.g. the ones listed in the product accessories online at
phoenixcontact.com/products).
• When using the product in direct connection with third-party
manufacturers, the user is responsible.
• For operating voltages > 50V AC, conductive connector housings must
be grounded
• Ensure that when laying the cable, the tensile load on the connectors
does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by PhoenixContact
• Use a protective cap to protect connectors that are not in use. The
suitable accessories are available online in the accessory section of the
product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly
connected.
https://www.phoenixcontact.com/us/products/1019517
03/23/2021Page3/4
Flush-type connector-SACC-E-MS-4CON-M16/0,5-18AWG-1019517
Technical data
Standards and Regulations
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are
applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient
conditions, the surface of the connector can continue to warm up. In
this case, the user is responsible for posting warnings (e.g. DIN EN ISO
13732-1:2008-12).
Environmental Product Compliance
REACh SVHC Lead 7439-92-1
China RoHS Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”, Category
“Manufacturer's declaration”
Classifications
eCl@ss
eCl@ss 10.0.1 27440102
eCl@ss 11.0 27440102
eCl@ss 9.0 27440102
ETIM
ETIM 6.0 EC002061
Approvals
Approvals
Approvals
EAC
Ex Approvals
Approval details
EAC B.01687
