SCOPE: Dua l, SPST, CM OS, TTL-Compatible Analog Switch
Device Type: Generic Number:
-1 DG200AA(x)/883B
Case Outline(s).
Outline Letter Mil-Std-1835 Case Outline Package Code
K GDIP1-T14 or CDIP2-T14 14 LEAD CERDIP J14
A MACY1-X10 10 Pin TO-100 A10
Ab solute Maximum Ratin gs
V+ to V- ..................................................................................................................................... 44V
V+ to GND ................................................................................................................................. 25V
Digital Input Overvoltage Range .....................................................…….….. (V- -2V) to (V+ +2V)
Continuous Current, Any terminal ..........................................................................………... 30mA
Current, S or D (Pulsed at 1ms, 10% duty cycle max) .......................................................... 100mA
Lead Temperature (soldering, 10 seconds) ....................................................................…….... +300°C
Storage Temperature .......................................................................................…….... -65°C to +150°C
Continuous Power Dissipation ........................................................................…………….. TA=+70°C
10 lead Can (derate 6.7mW/°C above +70°C) .............................................………………….. 533mW
14 lead CERDIP(derate 10mW/°C above +70°C) ................................................…………..... 727mW
Junct ion Temperature TJ .................................................................................………………. +150°C
Thermal Resista nce, J unction to Case, ΘJC:
Case Outline 10 lead Can ...........................................................…………………..... 45°C/W
Case Outline 14 lead CERDIP.............................................................…………….... 55°C/W
Thermal Resistance, Junction to Ambient, ΘJA:
Case Outline 10 lead Can ...........................................................………………….. 150°C/W
Case Outline 14 lead CERDIP..........................................................…………….... 110°C/W
Recommended O pera ting Conditions.
Ambient Operating Range (TA) ...........................................................…………... -55°C to +125°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage
to the device.These are stress ratings only, and functional operation of the device at these or any
other conditions beyond those indicated in the ope ratio nal sections of the specifications is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
---------------------------- Electrical Characteristics of DG200A/883B 19-0053 Rev. B
Page 2 of 5
TABLE 1. ELECTRICAL TESTS:
TEST Symbol CONDITIONS
-55°C≤TA≤+125°C
V+=15V, V-=-15V, GND=0V,
VINH=2.4V, VINL=0.8V
Unless otherwise specified
GROU P A
Subgroup Device
type Limits
Min Limits
Max Units
Analog-Signal
Range VANALOG VS=±15V 1,2,3 All -15 15 V
Drain-Source On
Resistance rDS(ON) VIN=0.8V, IS=-1mA, VD=±10V 1
2,3 All 70
100 Ω
Source-Off Leakage
Current IS(OFF) VIN=2.4V, V S=+/-14V,
VD=-/+14V 1
2All -2
-100 2
100 nA
Drain-Off Leakage
Current ID(OFF) VIN=2.4V, VS=+/-14V,
VD=-/+14V 1
2All -2
-100 2
100 nA
Channel-On
Leakage Current ID(ON) +
IS(ON)
VIN=0.8V, VS=VD=±14V 1
2All -2
-200 2
200 nA
Input Current with
Voltage High IINH VIN=2.4V
VIN=15V
1
2,3
1
2,3
All
-0.5
-1.0
0.5
1.0
µA
Input Current with
Voltage Low IINL VIN=0V 1
2,3 All -0.5
-1.0 µA
Positive Supply
Current I+ Both channels on or off 1,2,3 All 2 mA
Negat ive Supply
Current I- Both channels on or off 1,2,3 All -1.0 mA
DYNAMIC
Turn-On Time tON Figure 1, NOTE 1 9
10,11 All 1000
1500 ns
Turn-Off Time tOFF Figure 1, NOTE 1 9
10,11 All 425
800 ns
NOTE 1: Figure 1, See Commercial datasheet.
PIN CONFIGURATIONS:
14-Pin CERDIP 10 Pin Can LOGIC SWITCH
1IN2 IN1 0ON
2NC IN2 1OFF
3 GND GND
4NC S2
5S2 D2
6D2 V-
7V- NC
8NC D1
9D1 S1
10 S1 V+ (substrate and case)
11 NC
12 V+ (substrate)
13 NC
14 IN1
------------------------------------- Electrical Characteristics of 19-0053 Rev. B
DG200A/883B Page 3 of 5
ORDERING INFORMATION:
10 Lead Can DG200AAA/883B
14 CERDIP DG200AAK/883B
QUALITY ASSUR ANCE
Sampling and inspection procedures shall be in accordance with Mil-Prf-38535, Appendix A as
Specified in Mil-Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Conditio n, A, B, C, or D.
2. TA = +125°C, minimu m.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883,
Including Gro ups A, B, C, a nd D insp ection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883.
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2. ELECTRICAL TEST R EQUIREMENTS
Mil-Std-883 Test Requirements Subgroups
Per Method 5005, Table 1
Interim Electric Parameters
Method 5004 1
Final Electrical Parameters
Method 5005 1*, 2, 3, 9
Group A Test Requirements
Method 5005 1, 2, 3, 9, 10**, 11**
Group C and D End-Point Electrical Parameters
Method 5005 1
* PDA applies to Subgroup 1 only.
** Subgroups 10 and 11, if not tested, shall be guaranteed to the limits i n Table 1.
------------------------------------- Electrical Characteristics of 19-0053 Rev. B
DG200A/883B Page 4 of 5
