SCOPE: Dual, SPST, CMOS, TTL-Compatible Analog Switch Device Type: -1 Generic Number: DG200AA(x)/883B Case Outline(s). Outline Letter Mil-Std-1835 K GDIP1-T14 or CDIP2-T14 A MACY1-X10 Case Outline 14 LEAD CERDIP 10 Pin TO-100 Package Code J14 A10 Absolute Maximum Ratings V+ to V- ..................................................................................................................................... 44V V+ to GND ................................................................................................................................. 25V Digital Input Overvoltage Range ................................................................. (V- -2V) to (V+ +2V) Continuous Current, Any terminal ...................................................................................... 30mA Current, S or D (Pulsed at 1ms, 10% duty cycle max) .......................................................... 100mA Lead Temperature (soldering, 10 seconds) .............................................................................. +300C Storage Temperature ................................................................................................. -65C to +150C Continuous Power Dissipation ......................................................................................... TA=+70C 10 lead Can (derate 6.7mW/C above +70C) .................................................................... 533mW 14 lead CERDIP(derate 10mW/C above +70C) ................................................................. 727mW Junction Temperature TJ .................................................................................................... +150C Thermal Resistance, Junction to Case, JC: Case Outline 10 lead Can ..................................................................................... 45C/W Case Outline 14 lead CERDIP................................................................................ 55C/W Thermal Resistance, Junction to Ambient, JA: Case Outline 10 lead Can .................................................................................. 150C/W Case Outline 14 lead CERDIP............................................................................. 110C/W Recommended Operating Conditions. Ambient Operating Range (TA) .......................................................................... -55C to +125C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device.These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of DG200A/883B 19-0053 Page 2 of Rev. B 5 TABLE 1. ELECTRICAL TESTS: TEST Symbol Analog-Signal Range Drain-Source On Resistance Source-Off Leakage Current Drain-Off Leakage Current Channel-On Leakage Current Input Current with Voltage High VANALOG CONDITIONS -55CTA+125C V+=15V, V-=-15V, GND=0V, VINH=2.4V, VINL=0.8V Unless otherwise specified VS=15V rDS(ON) VIN=0.8V, IS=-1mA, VD=10V IS(OFF) VIN=2.4V, VS=+/-14V, VD=-/+14V VIN=2.4V, VS=+/-14V, VD=-/+14V VIN=0.8V, VS=VD=14V ID(OFF) ID(ON) + IS(ON) IINH GROUP A Subgroup VIN=2.4V Device type 1,2,3 All 1 2,3 1 2 1 2 1 2 1 2,3 All Limits Min Limits Max -15 All -2 -100 -2 -100 -2 -200 -0.5 -1.0 All All Units 15 V 70 100 2 100 2 100 2 200 Input Current with Voltage Low Positive Supply Current Negative Supply Current DYNAMIC Turn-On Time IINL VIN=0V I+ Both channels on or off 1 2,3 1 2,3 1,2,3 I- Both channels on or off 1,2,3 All tON Figure 1, NOTE 1 All Turn-Off Time tOFF Figure 1, NOTE 1 9 10,11 9 10,11 ------------------------------------- LOGIC 0 1 Electrical Characteristics of DG200A/883B nA 0.5 1.0 All All 2 -1.0 SWITCH ON OFF of Rev. B 5 mA mA 1000 1500 425 800 All 19-0053 Page 3 A -0.5 -1.0 NOTE 1: Figure 1, See Commercial datasheet. PIN CONFIGURATIONS: 14-Pin CERDIP 10 Pin Can 1 IN2 IN1 2 NC IN2 3 GND GND 4 NC S2 5 S2 D2 6 D2 V7 VNC 8 NC D1 9 D1 S1 10 S1 V+ (substrate and case) 11 NC 12 V+ (substrate) 13 NC 14 IN1 nA A All VIN=15V nA ns ns ORDERING INFORMATION: 10 Lead Can DG200AAA/883B 14 CERDIP DG200AAK/883B QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with Mil-Prf-38535, Appendix A as Specified in Mil-Std-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125C, minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, Including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883. 1. Test condition A, B, C, D. 2. TA = +125C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 Subgroups Per Method 5005, Table 1 1 1*, 2, 3, 9 1, 2, 3, 9, 10**, 11** 1 * PDA applies to Subgroup 1 only. ** Subgroups 10 and 11, if not tested, shall be guaranteed to the limits in Table 1. ------------------------------------- Electrical Characteristics of DG200A/883B 19-0053 Page 4 of Rev. B 5