Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HR Series SMBJ-HR Series RoHS Pb e3 Description Uni-directional The SMBJ-HR High Reliability series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Bi-directional Features * Excellent clamping capability * Low incremental surge resistance * Typical IR 1A for VR > 11.10V * SMT for minimal board footprint * Low profile package * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) * EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) * Built-in strain relief * Fast response time: typically less than 1.0ps from 0V to BV min Agency Approvals AGENCY AGENCY FILE NUMBER E128662/E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25C by 10/1000s Waveform (Fig.2)(Note 1), (Note 2) PPPM 600 W Power Dissipation on Infinite Heat Sink at TL=50OC PM(AV) 5.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) IFSM 100 A Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only VF 3.5V V TJ , TSTG -65 to 150 C Typical Thermal Resistance Junction to Lead RuJL 20 C/W Typical Thermal Resistance Junction to Ambient RuJA 100 C/W Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3. * 600W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * VBR @TJ= VBR@25C x (1+T x (TJ - 25)) (T:Temperature Coefficient) * Glass passivated chip junction * High temperature soldering guaranteed: 260C/40 seconds at terminals * UL Recognized compound meeting flammability rating V-0 * Meet MSL level1, per J-STD-020, LF maximun peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant * 2nd level interconnect is Pb-free per IPC/JEDEC J-STD-609A.01 Applications 2. Mounted on copper pad area of 0.2x0.2" (5.0 x 5.0mm) to each terminal. SMBJ-HR components are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only, duty cycle=4 per minute maximum. Functional Diagram Bi-directional Cathode Anode Uni-directional 1 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HR Series Electrical Characteristics (T =25C unless otherwise noted) A Part Number (Uni) Part Number (Bi) SMBJ5.0A-HR SMBJ6.0A-HR SMBJ6.5A-HR SMBJ7.0A-HR SMBJ7.5A-HR SMBJ8.0A-HR SMBJ8.5A-HR SMBJ9.0A-HR SMBJ10A-HR SMBJ11A-HR SMBJ12A-HR SMBJ13A-HR SMBJ14A-HR SMBJ15A-HR SMBJ16A-HR SMBJ17A-HR SMBJ18A-HR SMBJ20A-HR SMBJ22A-HR SMBJ24A-HR SMBJ26A-HR SMBJ28A-HR SMBJ30A-HR SMBJ33A-HR SMBJ36A-HR SMBJ40A-HR SMBJ43A-HR SMBJ45A-HR SMBJ48A-HR SMBJ51A-HR SMBJ54A-HR SMBJ58A-HR SMBJ60A-HR SMBJ64A-HR SMBJ70A-HR SMBJ75A-HR SMBJ78A-HR SMBJ85A-HR - SMBJ5.0CA-HR SMBJ6.0CA-HR SMBJ6.5CA-HR SMBJ7.0CA-HR SMBJ7.5CA-HR SMBJ8.0CA-HR SMBJ8.5CA-HR SMBJ9.0CA-HR SMBJ10CA-HR SMBJ11CA-HR SMBJ12CA-HR SMBJ13CA-HR SMBJ14CA-HR SMBJ15CA-HR SMBJ16CA-HR SMBJ17CA-HR SMBJ18CA-HR SMBJ20CA-HR SMBJ22CA-HR SMBJ24CA-HR SMBJ26CA-HR SMBJ28CA-HR SMBJ30CA-HR SMBJ33CA-HR SMBJ36CA-HR SMBJ40CA-HR SMBJ43CA-HR SMBJ45CA-HR SMBJ48CA-HR SMBJ51CA-HR SMBJ54CA-HR SMBJ58CA-HR SMBJ60CA-HR SMBJ64CA-HR SMBJ70CA-HR SMBJ75CA-HR SMBJ78CA-HR SMBJ85CA-HR SMBJ90CA-HR SMBJ100CA-HR SMBJ110CA-HR SMBJ120CA-HR SMBJ130CA-HR SMBJ150CA-HR SMBJ160CA-HR SMBJ170CA-HR Marking UNI BI KE KG KK KM KP KR KT KV KX KZ LE LG LK LM LP LR LT LV LX LZ ME MG MK MM MP MR MT MV MX MZ NE NG NK NM NP NR NT NV - AE AG AK AM AP AR AT AV AX AZ BE BG BK BM BP BR BT BV BX BZ CE CG CK CM CP CR CT CV CX CZ DE DG DK DM DP DR DT DV DX DZ EE EG EK EM EP ER Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.40 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 111.00 122.00 133.00 144.00 167.00 178.00 189.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 10 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Reverse Stand off Voltage VR (Volts) 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 Note: 1. For bidirectional type having VR of 10 volts and less, the IR limit is double. 2. 100% High Temperature Storage Life test and Reflow Simulation. 3. 100% HTRB(High Temperature Reverse Bias). For Unidirectional, 150OC/100%VR/96hours, for Bidirectional, 150OC/100%VR/192hrs(96hours for each direction for Bidirectional). 4. IR measured at room temperature +25OC 5. Each lot of parts will pass group B test requirement. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 2 Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @ VR (A) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 65.3 58.3 53.6 50.0 46.6 44.2 41.7 39.0 35.3 33.0 30.2 28.0 25.9 24.6 23.1 21.8 20.6 18.6 16.9 15.5 14.3 13.3 12.4 11.3 10.4 9.3 8.7 8.3 7.8 7.3 6.9 6.5 6.2 5.9 5.3 5.0 4.8 4.4 4.1 3.7 3.4 3.1 2.9 2.5 2.3 2.2 800 800 500 200 100 50 20 10 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HR Series Screen Process 100% Vision Inspection MIL-STD-750 method 2074 100% High Temperature Storage Life (168hrs,150C) MIL-STD-750 method 1031 100% X-RAY inspection MIL-STD-750 method 2076 100% Temperature Cycle Test (-55 to150C, 20 cycles, dwell time 15 min) MIL-STD-750 method 1051 100% Reflow (2x) JEDEC J-STD-020 100% Surge Test (2x) MIL-STD-750 method 4066 100% HTRB 150C Bias=VR(80% breakdown voltage, 96hrs, and each direction MIL-STD-750 method 1038 at 96 hrs for Bi-directional products) MIL-STD-750 method 4016.4021.4011 Final Electrical Test( 100% 3 sigma limit, 100% dynamic test and PAT limit) Note: Up-screen program can be specified by customer's request by contacting Littelfuse customer service Group B Test Requirement Screen Surge test Method Condition Requirement 10/1000 s Peak Pluse Waveform Maximum clamping Voltage (VC) @ Peak Plus Current (IPP) Sample Size 45 perform 10x Accept 0 failures MIL -STD-750, Method 1038.5 Applied voltage 100% VR@150C Sample size 45 340 hours (680 hours for bi-direction products, each direction 340 hours) Accept 0 failures IR@VR, V(BR)@IT Sample size 45 Accept 0 failures Burn - In (HTRB) Electrical test -- I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT Vc VBR VR V IR IT VR VBR Vc V Ipp Ipp PPPM VR VBR VC IR VF IT IR Peak Pulse Power Dissipation (IPP x VC) -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional 3 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HR Series Ratings and Characteristic Curves (T =25C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS Current Through TVS 10 1 0.2x0.2" (5.0x5.0mm) Copper Pad Area 0.1 0.000001 0.00001 Time Figure 3 - Pulse Derating Curve IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 150 80 60 40 20 0 25 50 75 100 125 150 tr=10sec Half Value IPPM IPPM ( ) 2 50 0 175 10/1000sec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Steady State Power Dissipation Derating Curve 10000 PM(AV), Steady State Power Dissipation (W) 6 Bi-directional V=0V 1000 Uni-directional V=0V Uni-directional @VR 100 Bi-directional @VR 10 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM Peak Value IPPM 100 TA-Ambient temperature (C) Cj (pF) 0.001 Figure 4 - Pulse Waveform 100 0 0.0001 td-Pulse Width (sec.) 10.0 100.0 VBR - Reverse Breakdown Voltage (V) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 5 4 3 2 1 0 1000.0 0 25 50 75 100 125 (C)(C) TA - TL-Lead AmbientTemperature Temperature (Power Dissipation on Infinite H eat Sink ) 4 150 175 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HR Series Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surge Current (A) 120 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz Soldering Parameters Pre Heat Lead-free assembly - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Ramp-up TL Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds 260 Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C tL Critical Zone TL to TP Ts(max) Ts(min) Ramp-down ts Preheat 25C Peak Temperature (TP) +0/-5 tp TP Temperature (T) Reflow Condition t 25C to Peak Time (t) C Environmental Specifications Physical Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 Weight 0.003 ounce, 0.093 grams Case JEDEC DO214AA. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Polarity Color band denotes cathode except Bidirectional H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102 RSH JESD22-B106 5 (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 Transient Voltage Suppression Diodes Surface Mount - 600W > SMBJ-HR Series Dimensions DO-214AA (SMB J-Bend) Dimensions Cathode Band (for Uni-directional products only) C A B H D F E G I Solder Pads Millimeters Min Max A 0.077 B 0.160 Min Max 0.086 1.950 2.200 0.180 4.060 4.570 C 0.130 0.155 3.300 3.940 D 0.084 0.096 2.130 2.440 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.205 0.220 5.210 5.590 H 0.006 0.012 0.152 0.305 I 0.089 - 2.260 - J 0.085 - 2.160 - K - 0.107 - 2.740 L 0.085 - 2.160 - L K J Inches (all dimensions in mm) Part Numbering System XXX C A -HR Cathode Band F SMBJ Part Marking System High Reliability 5% VOLTAGE TOLERANCE XX BI-DIRECTIONAL YMXXX VOLTAGE (for uni-directional products only) Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code SERIES Packaging Part number Component Package SMBJxxxXX-HR DO-214AA Quantity Packaging Option 3000 Tape & Reel - 12mm tape/13" reel Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.47 (12.0) Cathode 0.315 (8.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/28/18 Dimensions are in inches (and millimeters). Direction of Feed 6 (for unidirectional version only) Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Littelfuse: SMBJ33CA-HR SMBJ10A-HR SMBJ14CA-HR SMBJ75A-HR SMBJ20CA-HR SMBJ15CA-HR SMBJ8.0CA-HR SMBJ70CA-HR SMBJ16CA-HR SMBJ48CA-HR SMBJ7.5CA-HR SMBJ15A-HR SMBJ160CA-HR SMBJ8.0A-HR SMBJ78CA-HR SMBJ43A-HR SMBJ36A-HR SMBJ11CA-HR SMBJ78A-HR SMBJ13A-HR SMBJ130CA-HR SMBJ48A-HR SMBJ60CA-HR SMBJ7.0A-HR SMBJ9.0CA-HR SMBJ110CA-HR SMBJ12CA-HR SMBJ6.0CA-HR SMBJ150CA-HR SMBJ45CA-HR SMBJ51CA-HR SMBJ6.5CA-HR SMBJ90CA-HR SMBJ8.5CA-HR SMBJ26A-HR SMBJ6.5A-HR SMBJ85CA-HR SMBJ100CA-HR SMBJ18CA-HR SMBJ7.5A-HR SMBJ10CA-HR SMBJ40A-HR SMBJ22CA-HR SMBJ70A-HR SMBJ85A-HR SMBJ51A-HR SMBJ28A-HR SMBJ170CA-HR SMBJ13CA-HR SMBJ24A-HR SMBJ17CA-HR SMBJ58CA-HR SMBJ33A-HR SMBJ24CA-HR SMBJ58A-HR SMBJ26CA-HR SMBJ36CA-HR SMBJ45A-HR SMBJ11A-HR SMBJ12A-HR SMBJ30A-HR SMBJ9.0A-HR SMBJ43CA-HR SMBJ7.0CA-HR SMBJ120CA-HR SMBJ28CA-HR SMBJ64CA-HR SMBJ6.0A-HR SMBJ54A-HR SMBJ14A-HR SMBJ16A-HR SMBJ18A-HR SMBJ54CA-HR SMBJ40CA-HR SMBJ30CA-HR SMBJ22A-HR SMBJ5.0CA-HR SMBJ60A-HR SMBJ8.5A-HR SMBJ5.0A-HR SMBJ20A-HR SMBJ75CA-HR SMBJ64A-HR SMBJ17A-HR