Installation Instructions for the Issue F Basic Board Mount Pressure Sensors 50076346 TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified 60 mbar to 10 bar | 6 kPa to 1 MPa | 1 psi to 150 psi GENERAL INFORMATION Honeywell's Basic Board Mount Pressure Sensors: NBP Series, Uncompensated/Unamplified, and TBP Series, Compensated/ Unamplified, are piezoresistive silicon pressure sensors designed for customers who require a simple, cost-effective, mV output, unamplified, high quality, high resolution solution for medical and industrial applications. CAUTION MEDIA INCOMPATIBILITY * No gel coating option: The input port is limited to noncorrosive, non-ionic media such as dry air and gases and should not be exposed to condensation. The gases are limited to media that are compatible with the following wetted materials of construction: high temperature polyamide, silicone, epoxy, alumina ceramic, silicon, gold, and glass. * Silicon gel coating option: The gel coated sensors use the same materials in the wetted media path but are protected from condensation by a silicone-based gel coating. The gel coating option allows use in applications where condensation can occur. Failure to comply with these instructions may result in product damage. SOLDERING See soldering times and temperatures in Table 1. CAUTION IMPROPER CLEANING * Ensure cleaning fluids, such as appropriate alcohols or fluorinated solvents, are used based on the type of contaminants to be removed. * Do not immerse the sensor. Failure to comply with these instructions may result in product damage. Table 1. Absolute Maximum Ratings1 Characteristic Min. Supply voltage (Vsupply) Storage temperature Soldering time and temperature: lead solder temperature ( DIP) peak reflow temperature (Lead less SMT, SMT) 2 Max. Unit -12.0 12.0 -40 [-40] 125 [257] Vdc C [F] 4 s max. at 250 C [482 F] 15 s max. at 250 C [482 F] 1. Absolute maximum ratings are the extreme limits the device will withstand without damage. 2. Incorrect application of supply voltage or ground to the wrong pin may cause electrical failure. Table 2. Operating Specifications Characteristic Supply voltage (Vsupply):1, 2 TBP Series NBP Series Supply current (at 5.0 Vdc supply): TBP Series NBP Series Operating temperature range3 Compensated temperature range4 (TBP Series only) Input resistance (NBP Series only) Min. Typ. Max. Unit 1.5 1.8 5.0 5.0 12.0 12.0 Vdc -- -- -40 [-40] 0 [32] 2.4 0.6 1.5 -- -- 3.0 1.0 2.5 125 [257] 85 [185] 5.5 mA C [F] C [F] kOhm 1. Ratiometricity of the sensor (the ability of the device output to scale to the supply voltage) is achieved within the specified operating voltage. 2. Incorrect application of supply voltage or ground to the wrong pin may cause electrical failure. 3. Operating temperature range: The temperature range over which the sensor will produce an output proportional to pressure. 4. Compensated temperature range: The temperature range over which the sensor will produce an output proportional to pressure within the specified performance limits. Sensing and Control TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified ISSUE F 50076346 Table 3. Environmental Specifications Characteristic Parameter Humidity: 0 %RH to 95 %RH, non-condensing all external surfaces 0 %RH to 100 %RH, condensing internal surfaces of silicon gel coating option 0 %RH to 95 %RH, non-condensing internal surfaces of no coating option Vibration MIL-STD-202G, Method 204D, Condition B (15 g, 10 Hz to 2 kHz) Shock MIL-STD-202G, Method 213B, Condition C (100 g, 6 ms duration) Life1 1 million pressure cycles min. ESD: TBP Series MIL-STD 883 Method 3015.7, Class 1 NBP Series MIL-STD 883 Method 3015.7, Class 3 Solder reflow J-STD-020-D, MSL 1 (unlimited shelf life when stored at less than 30 C and 85 %RH) Notes: Life may vary depending on specific application in which the sensor is utilized. 1 Table 4. Wetted Materials Component Ports Substrate Adhesives Electronic components 2 Honeywell Sensing and Control No Gel Coating Option Silicon Gel Coating Option high temperature polyamide alumina ceramic epoxy, RTV ceramic, silicon, gold, glass high temperature polyamide not exposed: protected by silicone gel epoxy not exposed: protected by silicone gel TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified ISSUE F 50076346 Figure 2. DIP Package Dimensional Drawings (For reference only: mm [in].) AN: Single axial barbed port 4 3,50 [0.138] 3 Recommended PCB Pad Layout 7,00 [0.276] 10,94 MAX. [0.430] 3 2,54 [0.100] 4 3,56 [0.140] 5,50 [0.217] 11,50 [0.45] O1,91 [0.075] PIN 1 INDICATOR 2,23 [0.088] 1 2 2,54 TYP. [0.100] 0,25 [0.010] O 2,74 [0.108] O 2,32 [0.091] 4X 0,46 [0.018] 1,02 [0.040] O 6,50 [0.256] 11,50 [0.45] 2 1 8,64 [0.340] O 0,813 [0.032] LN: Single axial barbless port 4 10,94 MAX. [0.430] 3,50 [0.138] 3 5,83 [0.230] 7,00 [0.276] 3,84 [0.151] 3 4 5,50 [0.217] 11,5 [ 0.45] O 3,18 [0.125] 0,25 [0.010] PIN 1 INDICATOR 2,23 [0.088] 1 2 2,54 TYP. [0.100] O 6,50 [0.256] 4X 0,46 [0.018] 1,02 [0.040] 2 Table 8. Pinout for DIP Packages Pin 4 Pin 3 Vout+ GND Pin 1 Pin 2 Vsupply Vout- 1 8,64 [0.340] PN: Low-profile port 3 3,50 [0.138] 4 2,10 [0.083] 3,84 [0.151] 7,00 [0.276] 3 4 2 1 5,50 [0.217] 11,5 [0.45] O 6,50 [0.256] 0,25 [0.010] PIN 1 INDICATOR 2,23 [0.088] 1 2 2,54 TYP. [0.100] 1,02 [0.040] 4X 0,46 [0.018] 8,64 [0.340] Honeywell Sensing and Control 3 TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified ISSUE F 50076346 Figure 3. Leadless SMT Package Dimensional Drawings (For reference only: mm [in]) AN: Single axial barbed port Recommended PCB Pad Layout PAD 1 INDICATOR 3,56 [0.140] 7,00 [0.276] 2,54 [0.100] 10,94 MAX. [0.430] 3,84 MAX. [0.151] 1,00 [0.039] 6 3,50 [0.138] 7,00 [0.276] O1,91 [0.075] 5 O2,74 [0.108] 4 O2,32 [0.091] 3,50 [0.138] O6,50 [0.256] 1,02 [0.040] 1 2,50 [0.098] 2 3 2,50 TYP. [0.098] 5,46 [0.215] 1,27 [0.050] LN: Single axial barbless port Table 9. Pinout for Leadless SMT Pressure Packages PAD 1 INDICATOR 7,00 [0.276] 3,84 MAX. [0.151] O6,50 [0.256] 6 3,50 [0.138] O3,18 [0.125] 7,00 [0.276] 5 4 3,50 [0.138] 5,84 [0.230] 1,02 [0.040] 1,00 [0.039] Pad 1 Pad 6 1 Vsupply Vout+ Pad 2 Pad 5 NC NC Pad 3 Pad 4 Vout- GND 2 3 2,50 TYP. [0.098] 10,94 MAX. [0.430] PN: Low-profile port PAD 1 INDICATOR 1,00 [0.039] 3,84 MAX. [0.151] 7,00 [0.276] 6 3,50 [0.138] O6,50 [0.256] 7,00 [0.276] 5 4 3,50 [0.138] 4 Honeywell Sensing and Control 1,02 [0.040] 1 2 3 2,50 TYP. [0.098] TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified ISSUE F 50076346 Figure 4. SMT Package Dimensional Drawings (For reference only: mm [in]) AN: Single axial barbed port 3,50 [0.138] 4 Recommended PCB Pad Layout 10,94 [0.430] 3 7,00 [0.276] 3,84 [0.151] 3 5,50 [0.217] 1 O6,50 [0.256] 2 2,54 TYP. [0.100] 4X 1,27 [0.050] 0,25 [0.010] O1,91 [0.075] PIN 1 INDICATOR 2,032 [0.080] 11,5 [0.45] O2,74 [0.108] 2,25 [0.088] 2,54 [0.100] 4 O 2,32 [0.091] 1,02 [0.040] 3,03 [0.119] 4X 0,46 [0.018] 2 7,59 [0.30 ] 1 1,143 [0.045] LN: Single axial barbless port 4 10,94 MAX. [0.430] 5,83 3,84 [0.230] [0.151] 3,50 [0.138] 3 7,00 [0.276] 3 Table 10. Pinout for SMT Packages 4 5,50 [0.217] O3,18 [0.125] PIN 1 INDICATOR 2,25 [0.088] 11,5 [0.45] O6,50 [0.256] 1 4X 1,27 [0.050] 0,25 [0.010] 2 1,02 [0.040] 2,54. TYP [0.100] 3,03 [0.119] 4X 0,46 [0.018] 2 Pin 4 Pin 3 Vout+ GND Pin 1 Pin 2 Vsupply Vout- 1 PN: Low-profile port 4 3,50 [0.138] 3 2,10 [0.083] 7,00 [0.276] 3,84 MAX. [0.151] 3 4 5,50 [0.217] O6,50 [0.256] 11,5 [0.45] 1 2,25 [0.088] 4X 1,27 [0.050] 0,25 [0.010] PIN 1 INDICATOR 2 2,54 TYP. [0.100] 1,02 [0.040] 3,03 [0.119] 4X 0,46 [0.018] 2 1 Honeywell Sensing and Control 5 TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified ISSUE F 50076346 Figure 5. TBP Series Nomenclature and Order Guide For example, TBPDANN150PGUCV defines a TBP Series Basic Board Mount Pressure Sensor, DIP package, AN pressure port, no gel coating in media path,150 psi gage pressure range, unamplified, compensated, constant supply voltage. TBP D AN N 150PG U C V Series TBP Supply Voltage V Constant Package D DIP (Dual Inline Pin) L Leadless SMT (Surface Mount Technology) Compensation M SMT (Surface Mount Technology) C Compensated Pressure Port DIP AN Single axial barbed port Leadless SMT AN Single axial barbed port SMT AN Output Single axial barbed port U Unamplified Pressure Range LN Single axial barbless port LN Single axial barbless port LN Single axial barbless port 60 mbar to 10 bar Gage 060MG 0 mbar to 60 mbar PN Low-profile port PN Low-profile port PN Gel Coating Option N No gel coating in media path S Silicone gel coating in media path 6 Honeywell Sensing and Control Low-profile port 6 kPa to 1 MPa Gage 006KG 0 kPa to 6 kPa 1 psi to 150 psi Gage 001PG 0 psi to 1 psi 100MG 0 mbar to 100 mbar 010KG 0 kPa to 10 kPa 005PG 0 psi to 5 psi 160MG 0 mbar to 160 mbar 016KG 0 kPa to 16 kPa 015PG 0 psi to 15 psi 250MG 0 mbar to 250 mbar 025KG 0 kPa to 25 kPa 030PG 0 psi to 30 psi 400MG 0 bar to 400 mbar 040KG 0 kPa to 40 kPa 060PG 0 psi to 60 psi 600MG 0 bar to 600 mbar 060KG 0 kPa to 60 kPa 100PG 0 psi to 100 psi 001BG 0 bar to 1 bar 100KG 0 kPa to 100 kPa 150PG 0 psi to 150 psi 1.6BG 0 bar to 1.6 bar 160KG 0 kPa to 160 kPa 2.5BG 0 bar to 2.5 bar 250KG 0 kPa to 250 kPa 004BG 0 bar to 4 bar 400KG 0 kPa to 400 kPa 006BG 0 bar to 6 bar 600KG 0 kPa to 600 kPa 010BG 0 bar to 10 bar 001GG 0 kPa to 1 MPa TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified ISSUE F 50076346 Figure 6. NBP Series Nomenclature and Order Guide For example, NBPDANN150PGUNV defines an NBP Series Basic Board Mount Pressure Sensor, DIP package, AN pressure port, no gel coating in media path,150 psi gage pressure range, unamplified, uncompensated, constant supply voltage. NBP D AN N 150PG U N V Series NBP Supply Voltage V Constant Package D DIP (Dual Inline Pin) L Leadless SMT (Surface Mount Technology) Compensation M SMT (Surface Mount Technology) N Uncompensated Pressure Port DIP AN Single axial barbed port Leadless SMT AN Single axial barbed port SMT AN Output Single axial barbed port U Unamplified Pressure Range LN Single axial barbless port PN Low-profile port LN Single axial barbless port PN Low-profile port LN Single axial barbless port PN Low-profile port 60 mbar to 10 bar Absolute 1 psi to 150 psi Absolute 001BA 0 bar to 1 bar 015PA 0 psi to 15 psi 1.6BA 0 bar to 1.6 bar 030PA 0 psi to 30 psi 2.5BA 0 bar to 2.5 bar 060PA 0 psi to 60 psi 004BA 0 bar to 4 bar 100PA 0 psi to 100 psi 006BA 0 bar to 6 bar 150PA 0 psi to 150 psi 010BA 0 bar to 10 bar Gage Gage Gel Coating Option N No gel coating in media path S Silicone gel coating in media path 060MG 0 mbar to 60 mbar 001PG 0 psi to 1 psi 100MG 0 mbar to 100 mbar 005PG 0 psi to 5 psi 160MG 0 mbar to 160 mbar 015PG 0 psi to 15 psi 250MG 0 mbar to 250 mbar 030PG 0 psi to 30 psi 400MG 0 bar to 400 mbar 060PG 0 psi to 60 psi 600MG 0 bar to 600 mbar 100PG 0 psi to 100 psi 001BG 0 bar to 1 bar 150PG 0 psi to 150 psi 1.6BG 0 bar to 1.6 bar 2.5BG 0 bar to 2.5 bar 004BG 0 bar to 4 bar 006BG 0 bar to 6 bar 010BG 0 bar to 10 bar Honeywell Sensing and Control 7 TBP Series, Compensated/Unamplified NBP Series, Uncompensated/Unamplified WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. WARRANTY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell's standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyer's sole remedy and is in lieu of all warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. E-mail: info.sc@honeywell.com Internet: sensing.honeywell.com Phone and Fax: Asia Pacific +65 6355-2828 +65 6445-3033 Fax Europe +44 (0) 1698 481481 +44 (0) 1698 481676 Fax Latin America +1-305-805-8188 +1-305-883-8257 Fax USA/Canada +1-800-537-6945 +1-815-235-6847 +1-815-235-6545 Fax Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. Sensing and Control Honeywell 1985 Douglas Drive North honeywell.com 50076346 SALES AND SERVICE Honeywell serves its customers through a worldwide network of sales offices, representatives and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office or: While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Golden Valley, MN 55422 ISSUE F 50076346-F-EN IL50 October 2014 Copyright (c) 2014 Honeywell International Inc. All rights reserved. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Honeywell: TBPMANN060PGUCV TBPDLNN150PGUCV TBPMANS060MGUCV TBPMANN400MGUCV TBPDANN030PGUCV TBPDLNS030PGUCV TBPLANS030PGUCV TBPDLNN004BGUCV TBPLANS060MGUCV TBPLPNS1.6BGUCV TBPLANN060PGUCV TBPDANS150PGUCV TBPMANN015PGUCV TBPDANN060PGUCV TBPLPNS005PGUCV TBPDLNN100PGUCV TBPLPNS400MGUCV TBPDANN250MGUCV TBPDLNN060MGUCV TBPMANS030PGUCV TBPDLNS150PGUCV TBPDANN015PGUCV