S25FL128P 128 Megabit CMOS 3.0 Volt Flash Memory with 104-MHz SPI (Serial Peripheral Interface) Bus Data Sheet S25FL128P Cover Sheet This product is not recommended for new and current designs. For new and current designs, S25FL128S supersedes S25FL128P. This is the factory-recommended migration path. Please refer to the S25FL128S data sheet for specifications and ordering information. Notice to Readers: This document states the current technical specifications regarding the Spansion product(s) described herein. Each product described herein may be designated as Advance Information, Preliminary, or Full Production. See Notice On Data Sheet Designations for definitions. Publication Number S25FL128P_00 Revision 12 Issue Date Janauary 29, 2013 D at a S hee t Notice On Data Sheet Designations Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of product information or intended specifications throughout the product life cycle, including development, qualification, initial production, and full production. In all cases, however, readers are encouraged to verify that they have the latest information before finalizing their design. The following descriptions of Spansion data sheet designations are presented here to highlight their presence and definitions. Advance Information The Advance Information designation indicates that Spansion Inc. is developing one or more specific products, but has not committed any design to production. Information presented in a document with this designation is likely to change, and in some cases, development on the product may discontinue. Spansion Inc. therefore places the following conditions upon Advance Information content: "This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice." Preliminary The Preliminary designation indicates that the product development has progressed such that a commitment to production has taken place. This designation covers several aspects of the product life cycle, including product qualification, initial production, and the subsequent phases in the manufacturing process that occur before full production is achieved. Changes to the technical specifications presented in a Preliminary document should be expected while keeping these aspects of production under consideration. Spansion places the following conditions upon Preliminary content: "This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qualification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications." Combination Some data sheets contain a combination of products with different designations (Advance Information, Preliminary, or Full Production). This type of document distinguishes these products and their designations wherever necessary, typically on the first page, the ordering information page, and pages with the DC Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first page refers the reader to the notice on this page. Full Production (No Designation on Document) When a product has been in production for a period of time such that no changes or only nominal changes are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include those affecting the number of ordering part numbers available, such as the addition or deletion of a speed option, temperature range, package type, or VIO range. Changes may also include those needed to clarify a description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following conditions to documents in this category: "This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion Inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification corrections, or modifications to the valid combinations offered may occur." Questions regarding these document designations may be directed to your local sales office. 2 S25FL128P S25FL128P_00_12 Janauary 29, 2013 S25FL128P 128 Megabit CMOS 3.0 Volt Flash Memory with 104-MHz SPI (Serial Peripheral Interface) Bus Data Sheet This product is not recommended for new and current designs. For new and current designs, S25FL128S supersedes S25FL128P. This is the factory-recommended migration path. Please refer to the S25FL128S data sheet for specifications and ordering information. Distinctive Characteristics Process Technology Architectural Advantages - Manufactured on 0.09 m MirrorBit(R) process technology Single power supply operation Package Option - Full voltage range: 2.7V to 3.6V read and program operations - Industry Standard Pinouts - 16-pin SO package (300 mils) - 8-Contact WSON Package (6 x 8 mm) Memory Architecture - 128Mb uniform 256 KB sector product - 128Mb uniform 64 KB sector product Program Performance Characteristics - Page Program (up to 256 bytes) in 1.5 ms (typical) - Faster program time in Accelerated Programming mode (8.5 V-9.5 V on #WP/ACC) in 1.2 ms (typical) Speed - 104 MHz clock rate (maximum) Power Saving Standby Mode Erase - - - - 2 s typical 256 KB sector erase time 0.5 s typical 64 KB sector erase time 128 s typical bulk erase time Sector erase (SE) command (D8h) for 256 KB sectors; (20h or D8h) for 64KB sectors - Bulk erase command (C7h) for 256 KB sectors; (60h or C7h) for 64KB sectors Cycling Endurance - 100,000 cycles per sector typical Data Retention - 20 years typical Device ID - RDID (9Fh), READ_ID (90h) and RES (ABh) commands to read manufacturer and device ID information - RES command one-byte electronic signature for backward compatibility - Standby Mode 200 A (max) - Deep Power Down Mode 3 A (typical) Memory Protection Features Memory Protection - WP#/ACC pin works in conjunction with Status Register Bits to protect specified memory areas - 256 KB uniform sector product: Status Register Block Protection bits (BP2, BP1, BP0) in status register configure parts of memory as read-only. - 64KB uniform sector product: Status Register Block Protection bits (BP3, BP2, BP1, BP0) in status register configure parts of memory as read-only Software Features - SPI Bus Compatible Serial Interface Hardware Features x8 Parallel Programming Mode (for 16-pin SO package only) General Description The S25FL128P is a 3.0 Volt (2.7V to 3.6V), single-power-supply Flash memory device. The device consists of 64 sectors of 256 KB memory, or 256 sectors of 64 KB memory. The device accepts data written to SI (Serial Input) and outputs data on SO (Serial Output). The devices are designed to be programmed in-system with the standard system 3.0 volt VCC supply. The memory can be programmed 1 to 256 bytes at a time, using the Page Program command. The device supports Sector Erase and Bulk Erase commands. Each device requires only a 3.0 volt power supply (2.7V to 3.6V) for both read and write functions. Internally generated and regulated voltages are provided for the program operations. This device requires a high voltage supply to WP#/ACC pin for the Accelerated Programming mode. Publication Number S25FL128P_00 Revision 12 Issue Date Janauary 29, 2013 This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion Inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification corrections, or modifications to the valid combinations offered may occur. D at a S hee t Table of Contents Distinctive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 1. Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. Input/Output Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4. Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5.1 Valid Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6. Spansion SPI Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7. Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Byte or Page Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Sector Erase / Bulk Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 Monitoring Write Operations Using the Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Active Power and Standby Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6 Data Protection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 Hold Mode (HOLD#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. Sector Address Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 9. Parallel Mode (for 16-pin SO package only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 10. Accelerated Programming Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 11. Command Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Read Data Bytes (READ: 03h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 Read Data Bytes at Higher Speed (FAST_READ: 0Bh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3 Read Identification (RDID: 9Fh). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4 Read Manufacturer and Device ID (READ_ID: 90h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5 Write Enable (WREN: 06h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.6 Write Disable (WRDI: 04h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.7 Read Status Register (RDSR: 05h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.8 Write Status Register (WRSR: 01h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.9 Page Program (PP: 02h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.10 Sector Erase (SE: 20h, D8h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.11 Bulk Erase (BE: C7h, 60h). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.12 Deep Power Down (DP: B9h) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.13 Release from Deep Power Down (RES: ABh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.14 Release from Deep Power Down and Read Electronic Signature (RES: ABh) . . . . . . . . . . . 11.15 Command Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. Program Acceleration via WP#/ACC pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 13. Power-up and Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 12 12 12 12 12 12 12 14 19 19 21 22 24 25 26 26 29 30 33 34 35 36 36 38 14. Initial Delivery State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 15. Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 16. Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 17. DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 18. Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 19. AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 19.1 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 20. Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 20.1 SO3 016 wide -- 16-pin Plastic Small Outline Package (300-mil Body Width) . . . . . . . . . . . 46 20.2 WNF008 -- WSON 8-contact (6 x 8 mm) No-Lead Package . . . . . . . . . . . . . . . . . . . . . . . . 47 21. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Figures Figure 2.1 Figure 2.2 Figure 6.1 Figure 6.2 Figure 7.1 Figure 11.1 Figure 11.2 Figure 11.3 Figure 11.4 Figure 11.5 Figure 11.6 Figure 11.7 Figure 11.8 Figure 11.9 Figure 11.10 Figure 11.11 Figure 11.12 Figure 11.13 Figure 11.14 Figure 11.15 Figure 11.16 Figure 11.17 Figure 11.18 Figure 11.19 Figure 11.20 16-pin Plastic Small Outline Package (SO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8-Pin WSON Package (6 x 8 mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bus Master and Memory Devices on the SPI Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SPI Modes Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Hold Mode Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Read Data Bytes (READ) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Parallel Read Instruction Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Read Data Bytes at Higher Speed (FAST_READ) Command Sequence . . . . . . . . . . . . . . . 21 Read Identification Command Sequence and Data Out Sequence. . . . . . . . . . . . . . . . . . . . 22 Parallel Read_ID Command Sequence and Data Out Sequence . . . . . . . . . . . . . . . . . . . . . 23 Serial READ_ID Instruction Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Parallel Read_ID Instruction Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Write Enable (WREN) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Write Disable (WRDI) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Read Status Register (RDSR) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Parallel Read Status Register (RDSR) Instruction Sequence . . . . . . . . . . . . . . . . . . . . . . . .28 Write Status Register (WRSR) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Parallel Write Status Register (WRSR) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . 29 Page Program (PP) Command Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Parallel Page Program (PP) Instruction Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Sector Erase (SE) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Bulk Erase (BE) Command Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Deep Power Down (DP) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Release from Deep Power Down (RES) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . 36 Serial Release from Deep Power Down and Read Electronic Signature (RES) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Figure 11.21 Parallel Release from Deep Power Down and Read Electronic Signature (RES) Command Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Figure 12.1 ACC Program Acceleration Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Figure 13.1 Power-Up Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure 13.2 Power-down and Voltage Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure 15.1 Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Figure 15.2 Maximum Positive Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure 18.1 AC Measurements I/O Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Figure 19.1 SPI Mode 0 (0,0) Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure 19.2 SPI Mode 0 (0,0) Output Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure 19.3 HOLD# Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Figure 19.4 Write Protect Setup and Hold Timing during WRSR when SRWD=1 . . . . . . . . . . . . . . . . . . 45 Janauary 29, 2013 S25FL128P_00_12 S25FL128P 5 D at a S hee t Tables Table 5.1 Table 7.1 Table 7.2 Table 8.1 Table 8.2 Table 8.3 Table 11.1 Table 11.2 Table 11.3 Table 11.4 Table 11.5 Table 11.6 Table 12.1 Table 13.1 Table 15.1 Table 16.1 Table 17.1 Table 18.1 Table 19.1 6 S25FL128P Valid Combinations Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 S25FL128P Protected Area Sizes (Uniform 256 KB sector) . . . . . . . . . . . . . . . . . . . . . . . . . .13 S25FL128P Protected Area Sizes (Uniform 64 KB sector) . . . . . . . . . . . . . . . . . . . . . . . . . . .13 S25FL128P Device Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 S25FL128P Sector Address Table (Uniform 256 KB sector) . . . . . . . . . . . . . . . . . . . . . . . . .15 S25FL128P Sector Address Table (Uniform 64 KB sector) . . . . . . . . . . . . . . . . . . . . . . . . . .16 Manufacturer & Device Identification, RDID (9Fh) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 READ_ID Command and Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 S25FL128P Status Register (Uniform 256 KB sector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 S25FL128P Status Register (Uniform 64 KB sector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Protection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Command Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 ACC Program Acceleration Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Power-Up / Power-Down Voltage and Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 DC Characteristics (CMOS Compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Test Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et 1. Block Diagram SRAM PS X D E C Array - L Array - R Logic RD DATA PATH Janauary 29, 2013 S25FL128P_00_12 S25FL128P WP#/ACC HOLD# VCC GND SO/PO[7-0] SI SCK CS# IO 7 D at a S hee t 2. Connection Diagrams Figure 2.1 16-pin Plastic Small Outline Package (SO) HOLD# 1 16 SCK VCC 2 15 SI NC 3 14 PO6 PO2 4 13 PO5 PO1 5 12 PO4 PO0 6 11 PO3 CS# 7 10 GND SO/PO7 8 9 WP#/ACC Figure 2.2 8-Pin WSON Package (6 x 8 mm) CS# 1 SO 2 8 VCC 7 HOLD# WSON WP#/ACC 3 6 SCK GND 4 5 SI Note: There is an exposed central pad on the underside of the WSON package. This should not be connected to any voltage or signal line on the PCB. Connecting the central pad to GND (VSS) is possible, provided PCB routing ensures 0mV difference between voltage at the WSON GND (VSS) lead and the central exposed pad. 8 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et 3. Input/Output Descriptions Signal Name I/O SO (Signal Data Output) Output PO[7-0] (Parallel Data Input/Output) Input/Output Description Transfers data serially out of the device on the falling edge of SCK. Transfers parallel data into the device on the rising edge of SCK or out of the device on the falling edge of SCK. SI (Serial Data Input) Input Transfers data serially into the device. Device latches commands, addresses, and program data on SI on the rising edge of SCK. SCK (Serial Clock) Input Provides serial interface timing. Latches commands, addresses, and data on SI on rising edge of SCK. Triggers output on SO after the falling edge of SCK. CS# (Chip Select) Input Places device in active power mode when driven low. Deselects device and places SO at high impedance when high. After power-up, device requires a falling edge on CS# before any command is written. Device is in standby mode when a program, erase, or Write Status Register operation is not in progress. HOLD# (Hold) Input Pauses any serial communication with the device without deselecting it. When driven low, SO is at high impedance, and all input at SI and SCK are ignored. Requires that CS# also be driven low. WP#/ACC (Write Protect/Accelerated Programming) Input When driven low, prevents any program or erase command from altering the data in the protected memory area specified by Status Register bits (BP bits). If the system asserts VHH on this pin, accelerated programming operation is provided. VCC Input Supply Voltage GND Input Ground 4. Logic Symbol VCC SO SI PO[7-0] (For 16-pin SO package) SCK CS# WP#/ACC HOLD# GND Janauary 29, 2013 S25FL128P_00_12 S25FL128P 9 D at a S hee t 5. Ordering Information This product is not recommended for new and current designs. For new and current designs, S25FL128S supersedes S25FL128P. This is the factory-recommended migration path. Please refer to the S25FL128S data sheet for specifications and ordering information. The ordering part number is formed by a valid combination of the following: S25FL 128 P 0X M F I 00 1 PACKING TYPE 0 = Tray 1 = Tube 3 = 13" Tape and Reel MODEL NUMBER (Additional Ordering Options) 00 = Uniform 64 KB sector product 01 = Uniform 256 KB sector product TEMPERATURE RANGE I = Industrial (-40C to + 85C) PACKAGE MATERIALS F = Lead (Pb)-free PACKAGE TYPE M = 16-pin SO package N = 8-pin WSON package SPEED 0X = 104 MHz DEVICE TECHNOLOGY P = 0.09 m MirrorBit(R) Process Technology DENSITY 128 = 128 Mbit DEVICE FAMILY S25FL Spansion Memory 3.0 Volt-only, Serial Peripheral Interface (SPI) Flash Memory Table 5.1 S25FL128P Valid Combinations Table S25FL128P Valid Combinations Base Ordering Part Number Speed Option Package & Temperature S25FL128P 0X MFI, NFI Model Number 00 01 Packing Type 0, 1, 3 Package Marking (See Note) FL128P + I + F FL128P + I + FL Note Package marking omits leading "S25" and speed, package, and model number form. 5.1 Valid Combinations Table 5.1 lists the valid combinations configurations planned to be supported in volume for this device. 10 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et 6. Spansion SPI Modes A microcontroller can use either of its two SPI modes to control Spansion SPI Flash memory devices: CPOL = 0, CPHA = 0 (Mode 0) CPOL = 1, CPHA = 1 (Mode 3) Input data is latched in on the rising edge of SCK, and output data is available from the falling edge of SCK for both modes. When the bus master is in standby mode, SCK is as shown in Figure 6.2 for each of the two modes: SCK remains at 0 for (CPOL = 0, CPHA = 0 Mode 0) SCK remains at 1 for (CPOL = 1, CPHA = 1 Mode 3) Figure 6.1 Bus Master and Memory Devices on the SPI Bus SO SPI Interface with (CPOL, CPHA) = (0, 0) or (1, 1) SI SCK SCK SO SI SCK SO SI SCK SO SI Bus Master SPI Memory Device CS3 CS2 SPI Memory Device SPI Memory Device CS1 HOLD# CS# WP#/ACC CS# HOLD# CS# WP#/ACC HOLD# WP#/ACC Note The Write Protect/Accelerated Programming (WP#/ACC) and Hold (HOLD#) signals should be driven high (logic level 1) or low (logic level 0) as appropriate. Figure 6.2 SPI Modes Supported CS# CPOL CPHA Mode 0 0 0 SCK Mode 3 1 1 SCK SI MSB SO Janauary 29, 2013 S25FL128P_00_12 MSB S25FL128P 11 D at a S hee t 7. Device Operations All Spansion SPI devices (S25FL-P) accept and output data in bytes (8 bits at a time). 7.1 Byte or Page Programming Programming data requires two commands: Write Enable (WREN), which is one byte, and a Page Program (PP) sequence, which consists of four bytes plus data. The Page Program sequence accepts from 1 byte up to 256 consecutive bytes of data (which is the size of one page) to be programmed in one operation. Programming means that bits can either be left at the current state (1 or 0), or programmed from 1 to 0. Changing bits from 0 to 1 requires an erase operation. Before this can be applied, the bytes of the memory need to be first erased to all 1's (FFh) before any programming. 7.2 Sector Erase / Bulk Erase The Sector Erase (SE) and Bulk Erase (BE) commands set all the bits in a sector or the entire memory array to 1. While bits can be individually programmed from a 1 to 0, erasing bits from 0 to 1 must be done on a sector-wide (SE) or array-wide (BE) level. The memory array needs to be first erased to all 1's (FFh) before any programming. 7.3 Monitoring Write Operations Using the Status Register The host system can determine when a Write Status Register, program, or erase operation is complete by monitoring the Write in Progress (WIP) bit in the Status Register. The Read from Status Register command provides the state of the WIP bit. 7.4 Active Power and Standby Power Modes The device is enabled and in the Active Power mode when Chip Select (CS#) is Low. When CS# is high, the device is disabled, but may still be in the Active Power mode until all program, erase, and Write Status Register operations have completed. The device then goes into the Standby Power mode, and power consumption drops to ISB. The Deep Power Down (DP) command provides additional data protection against inadvertent signals. After writing the DP command, the device ignores any further program or erase commands, and reduces its power consumption to IDP. 7.5 Status Register The Status Register contains the status and control bits that can be read or set by specific commands (see Table Table 11.6, Command Definitions on page 38): Write In Progress (WIP): Indicates whether the device is performing a Write Status Register, program or erase operation. Write Enable Latch (WEL): Indicates the status of the internal Write Enable Latch. Block Protect (BP2, BP1, BP0 for uniform 256 KB sector product: BP3, BP2, BP1, BP0 for uniform 64 KB sector product): Non-volatile bits that define memory area to be software-protected against program and erase commands. Status Register Write Disable (SRWD): Places the device in the Hardware Protected mode when this bit is set to 1 and the WP#/ACC input is driven low. In this mode, the non-volatile bits of the Status Register (SRWD, BP3, BP2, BP1, BP0) become read-only bits. 7.6 Data Protection Modes Spansion SPI Flash memory devices provide the following data protection methods: The Write Enable (WREN) command: Must be written prior to any command that modifies data. The WREN command sets the Write Enable Latch (WEL) bit. The WEL bit resets (disables writes) on power-up or after the device completes the following commands: - Page Program (PP) 12 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et - Sector Erase (SE) - Bulk Erase (BE) - Write Disable (WRDI) - Write Status Register (WRSR) Software Protected Mode (SPM): The Block Protect (BP2, BP1, BP0 for uniform 256 KB sector product: BP3, BP2, BP1, BP0 for uniform 64 KB sector product) bits define the section of the memory array that can be read but not programmed or erased. Table 7.1 shows the sizes and address ranges of protected areas that are defined by Status Register bits BP2:BP0 for uniform 256 KB sector product, BP3:BP0 for uniform 64 KB sector product). Hardware Protected Mode (HPM): The Write Protect (WP#/ACC) input and the Status Register Write Disable (SRWD) bit together provide write protection. Clock Pulse Count: The device verifies that all program, erase, and Write Status Register commands consist of a clock pulse count that is a multiple of eight before executing them. Table 7.1 S25FL128P Protected Area Sizes (Uniform 256 KB sector) Status Register Block Protect Bits Memory Array Protected Address Range Unprotected Address Range Protected Sectors Unprotected Sectors Protected Portion of Total Memory Area BP2 BP1 BP0 0 0 0 None (0) 000000h-FFFFFFh (64) SA63:SA0 0 0 0 1 FC0000h-FFFFFFh (1) SA63 000000h-FBFFFFh (32) SA62:SA0 1/64 0 1 0 F80000h-FFFFFFh (2) SA63:SA62 000000h-F7FFFFh (16) SA61:SA0 1/32 0 1 1 F00000h-FFFFFFh (4) SA63:SA60 000000h-EFFFFFh (8) SA59:SA0 1/16 1 0 0 E00000h-FFFFFFh (8) SA63:SA56 000000h-DFFFFFh (4) SA55:SA0 1/8 1 0 1 C00000h-FFFFFFh (16) SA63:SA48 000000h-BFFFFFh (2) SA47:SA0 1/4 1 1 0 800000h-FFFFFFh (32) SA63:SA32 000000h-7FFFFFh (1) SA31:SA0 1/2 1 1 1 000000h-FFFFFFh (64) SA63:SA0 None (0) All Table 7.2 S25FL128P Protected Area Sizes (Uniform 64 KB sector) Status Register Block Protect Bits Memory Array Protected Address Range Protected Portion of Total Memory Area Unprotected Address Range Unprotected Sectors (0) 000000h-FFFFFFh (256) SA255:SA0 0 (2) SA255:SA254 000000h-FDFFFFh (128) SA253:SA0 1/128 000000h-FBFFFFh (64) SA251:SA0 1/64 BP3 BP2 BP1 BP0 0 0 0 0 None 0 0 0 1 FE0000h-FFFFFFh 0 0 1 0 FC0000h-FFFFFFh (4) SA255:SA252 0 0 1 1 F80000h-FFFFFFh (8) SA255:SA248 000000h-F7FFFFh (32) SA247:SA0 1/32 0 1 0 0 F00000h-FFFFFFh (16) SA255:SA240 000000h-EFFFFFh (16) SA239:SA0 1/16 0 1 0 1 E00000h-FFFFFFh (32) SA255:SA224 000000h-DFFFFFh (8) SA223:SA0 1/8 0 1 1 0 C00000h-FFFFFFh (64) SA255:SA192 000000h-BFFFFFh (4) SA191:SA0 1/4 0 1 1 1 800000h-FFFFFFh (128) SA255:SA128 000000h-7FFFFFh (2) SA127:SA0 1/2 1 0 0 0 000000h-FFFFFFh (256) SA255:SA0 None (0) All 1 0 0 1 000000h-FFFFFFh (256) SA255:SA0 None (0) All 1 0 1 0 000000h-FFFFFFh (256) SA255:SA0 None (0) All 1 0 1 1 000000h-FFFFFFh (256) SA255:SA0 None (0) All 1 1 0 0 000000h-FFFFFFh (256) SA255:SA0 None (0) All 1 1 0 1 000000h-FFFFFFh (256) SA255:SA0 None (0) All 1 1 1 0 000000h-FFFFFFh (256) SA255:SA0 None (0) All 1 1 1 1 000000h-FFFFFFh (256) SA255:SA0 None (0) All Janauary 29, 2013 S25FL128P_00_12 Protected Sectors S25FL128P 13 D at a 7.7 S hee t Hold Mode (HOLD#) The Hold input (HOLD#) stops any serial communication with the device, but does not terminate any Write Status Register, program or erase operation that is currently in progress. The Hold mode starts on the falling edge of HOLD# if SCK is also low (see Figure 7.1 on page 14, standard use). If the falling edge of HOLD# does not occur while SCK is low, the Hold mode begins after the next falling edge of SCK (non-standard use). The Hold mode ends on the rising edge of HOLD# signal (standard use) if SCK is also low. If the rising edge of HOLD# does not occur while SCK is low, the Hold mode ends on the next falling edge of CLK (nonstandard use) See Figure 7.1. The SO output is high impedance, and the SI and SCK inputs are ignored (don't care) for the duration of the Hold mode. CS# must remain low for the entire duration of the Hold mode to ensure that the device internal logic remains unchanged. If CS# goes high while the device is in the Hold mode, the internal logic is reset. To prevent the device from reverting to the Hold mode when device communication is resumed, HOLD# must be held high, followed by driving CS# low. Figure 7.1 Hold Mode Operation SCK HOLD# Hold Condition (standard use) Hold Condition (non-standard use) 8. Sector Address Table Table 8.1 shows the size of the memory array, sectors, and pages. The device uses pages to cache the program data before the data is programmed into the memory array. Each page or byte can be individually programmed (bits are changed from 1 to 0). The data is erased (bits are changed from 0 to 1) on a sector- or device-wide basis using the SE or BE commands. Table 8.2 shows the starting and ending address for each sector. The complete set of sectors comprises the memory array of the Flash device. Table 8.1 S25FL128P Device Organization Each Device has Each Sector has Each Page has 16,777,216 262144 (256 KB sector) 65536 (64 KB sector) 256 bytes 65,536 1024 (256 KB sector) 256 (64 KB sector) -- pages -- -- sectors 64 (256 KB sector) 256 (64 KB sector) 14 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Table 8.2 S25FL128P Sector Address Table (Uniform 256 KB sector) Sector Address Range Sector Address Range 63 FC0000h FFFFFFh 31 7C0000h 7FFFFFh 62 F80000h FBFFFFh 30 780000h 7BFFFFh 61 F40000h F7FFFFh 29 740000h 77FFFFh 60 F00000h F3FFFFh 28 700000h 73FFFFh 59 EC0000h EFFFFFh 27 6C0000h 6FFFFFh 58 E80000h EBFFFFh 26 680000h 6BFFFFh 57 E40000h E7FFFFh 25 640000h 67FFFFh 56 E00000h E3FFFFh 24 600000h 63FFFFh 55 DC0000h DFFFFFh 23 5C0000h 5FFFFFh 54 D80000h DBFFFFh 22 580000h 5BFFFFh 53 D40000h D7FFFFh 21 540000h 57FFFFh 52 D00000h D3FFFFh 20 500000h 53FFFFh 51 CC0000h CFFFFFh 19 4C0000h 4FFFFFh 50 C80000h CBFFFFh 18 480000h 4BFFFFh 49 C40000h C7FFFFh 17 440000h 47FFFFh 48 C00000h C3FFFFh 16 400000h 43FFFFh 47 BC0000h BFFFFFh 15 3C0000h 3FFFFFh 46 B80000h BBFFFFh 14 380000h 3BFFFFh 45 B40000h B7FFFFh 13 340000h 37FFFFh 44 B00000h B3FFFFh 12 300000h 33FFFFh 43 AC0000h AFFFFFh 11 2C0000h 2FFFFFh 42 A80000h ABFFFFh 10 280000h 2BFFFFh 41 A40000h A7FFFFh 9 240000h 27FFFFh 40 A00000h A3FFFFh 8 200000h 23FFFFh 39 9C0000h 9FFFFFh 7 1C0000h 1FFFFFh 38 980000h 9BFFFFh 6 180000h 1BFFFFh 37 940000h 97FFFFh 5 140000h 17FFFFh 36 900000h 93FFFFh 4 100000h 13FFFFh 35 8C0000h 8FFFFFh 3 0C0000h 0FFFFFh 34 880000h 8BFFFFh 2 080000h 0BFFFFh 33 840000h 87FFFFh 1 040000h 07FFFFh 32 800000h 83FFFFh 0 000000h 03FFFFh Janauary 29, 2013 S25FL128P_00_12 S25FL128P 15 D at a S hee t Table 8.3 S25FL128P Sector Address Table (Uniform 64 KB sector) (Sheet 1 of 2) Sector 16 Address Range Sector Address Range Sector Address Range 255 FF0000h FFFFFFh 207 CF0000h CFFFFFh 159 9F0000h 9FFFFFh 254 FE0000h FEFFFFh 206 CE0000h CEFFFFh 158 9E0000h 9EFFFFh 253 FD0000h FDFFFFh 205 CD0000h CDFFFFh 157 9D0000h 9DFFFFh 252 FC0000h FCFFFFh 204 CC0000h CCFFFFh 156 9C0000h 9CFFFFh 251 FB0000h FBFFFFh 203 CB0000h CBFFFFh 155 9B0000h 9BFFFFh 250 FA0000h FAFFFFh 202 CA0000h CAFFFFh 154 9A0000h 9AFFFFh 249 F90000h F9FFFFh 201 C90000h C9FFFFh 153 990000h 99FFFFh 248 F80000h F8FFFFh 200 C80000h C8FFFFh 152 980000h 98FFFFh 247 F70000h F7FFFFh 199 C70000h C7FFFFh 151 970000h 97FFFFh 246 F60000h F6FFFFh 198 C60000h C6FFFFh 150 960000h 96FFFFh 245 F50000h F5FFFFh 197 C50000h C5FFFFh 149 950000h 95FFFFh 244 F40000h F4FFFFh 196 C40000h C4FFFFh 148 940000h 94FFFFh 243 F30000h F3FFFFh 195 C30000h C3FFFFh 147 930000h 93FFFFh 242 F20000h F2FFFFh 194 C20000h C2FFFFh 146 920000h 92FFFFh 241 F10000h F1FFFFh 193 C10000h C1FFFFh 145 910000h 91FFFFh 240 F00000h F0FFFFh 192 C00000h C0FFFFh 144 900000h 90FFFFh 239 EF0000h EFFFFFh 191 BF0000h BFFFFFh 143 8F0000h 8FFFFFh 238 EE0000h EEFFFFh 190 BE0000h BEFFFFh 142 8E0000h 8EFFFFh 237 ED0000h EDFFFFh 189 BD0000h BDFFFFh 141 8D0000h 8DFFFFh 236 EC0000h ECFFFFh 188 BC0000h BCFFFFh 140 8C0000h 8CFFFFh 235 EB0000h EBFFFFh 187 BB0000h BBFFFFh 139 8B0000h 8BFFFFh 234 EA0000h EAFFFFh 186 BA0000h BAFFFFh 138 8A0000h 8AFFFFh 233 E90000h E9FFFFh 185 B90000h B9FFFFh 137 890000h 89FFFFh 232 E80000h E8FFFFh 184 B80000h B8FFFFh 136 880000h 88FFFFh 231 E70000h E7FFFFh 183 B70000h B7FFFFh 135 870000h 87FFFFh 230 E60000h E6FFFFh 182 B60000h B6FFFFh 134 860000h 86FFFFh 229 E50000h E5FFFFh 181 B50000h B5FFFFh 133 850000h 85FFFFh 228 E40000h E4FFFFh 180 B40000h B4FFFFh 132 840000h 84FFFFh 227 E30000h E3FFFFh 179 B30000h B3FFFFh 131 830000h 83FFFFh 226 E20000h E2FFFFh 178 B20000h B2FFFFh 130 820000h 82FFFFh 225 E10000h E1FFFFh 177 B10000h B1FFFFh 129 810000h 81FFFFh 224 E00000h E0FFFFh 176 B00000h B0FFFFh 128 800000h 80FFFFh 223 DF0000h DFFFFFh 175 AF0000h AFFFFFh 127 7F0000h 7FFFFFh 222 DE0000h DEFFFFh 174 AE0000h AEFFFFh 126 7E0000h 7EFFFFh 221 DD0000h DDFFFFh 173 AD0000h ADFFFFh 125 7D0000h 7DFFFFh 220 DC0000h DCFFFFh 172 AC0000h ACFFFFh 124 7C0000h 7CFFFFh 219 DB0000h DBFFFFh 171 AB0000h ABFFFFh 123 7B0000h 7BFFFFh 218 DA0000h DAFFFFh 170 AA0000h AAFFFFh 122 7A0000h 7AFFFFh 217 D90000h D9FFFFh 169 A90000h A9FFFFh 121 790000h 79FFFFh 216 D80000h D8FFFFh 168 A80000h A8FFFFh 120 780000h 78FFFFh 215 D70000h D7FFFFh 167 A70000h A7FFFFh 119 770000h 77FFFFh 214 D60000h D6FFFFh 166 A60000h A6FFFFh 118 760000h 76FFFFh 213 D50000h D5FFFFh 165 A50000h A5FFFFh 117 750000h 75FFFFh 212 D40000h D4FFFFh 164 A40000h A4FFFFh 116 740000h 74FFFFh 211 D30000h D3FFFFh 163 A30000h A3FFFFh 115 730000h 73FFFFh 210 D20000h D2FFFFh 162 A20000h A2FFFFh 114 720000h 72FFFFh 209 D10000h D1FFFFh 161 A10000h A1FFFFh 113 710000h 71FFFFh 208 D00000h D0FFFFh 160 A00000h A0FFFFh 112 700000h 70FFFFh S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Table 8.3 S25FL128P Sector Address Table (Uniform 64 KB sector) (Sheet 2 of 2) Sector Address Range Sector Address Range Sector Address Range 111 6F0000h 6FFFFFh 71 470000h 47FFFFh 31 1F0000h 1FFFFFh 110 6E0000h 6EFFFFh 70 460000h 46FFFFh 30 1E0000h 1EFFFFh 109 6D0000h 6DFFFFh 69 450000h 45FFFFh 29 1D0000h 1DFFFFh 108 6C0000h 6CFFFFh 68 440000h 44FFFFh 28 1C0000h 1CFFFFh 107 6B0000h 6BFFFFh 67 430000h 43FFFFh 27 1B0000h 1BFFFFh 106 6A0000h 6AFFFFh 66 420000h 42FFFFh 26 1A0000h 1AFFFFh 105 690000h 69FFFFh 65 410000h 41FFFFh 25 190000h 19FFFFh 104 680000h 68FFFFh 64 400000h 40FFFFh 24 180000h 18FFFFh 103 670000h 67FFFFh 63 3F0000h 3FFFFFh 23 170000h 17FFFFh 102 660000h 66FFFFh 62 3E0000h 3EFFFFh 22 160000h 16FFFFh 101 650000h 65FFFFh 61 3D0000h 3DFFFFh 21 150000h 15FFFFh 100 640000h 64FFFFh 60 3C0000h 3CFFFFh 20 140000h 14FFFFh 99 630000h 63FFFFh 59 3B0000h 3BFFFFh 19 130000h 13FFFFh 98 620000h 62FFFFh 58 3A0000h 3AFFFFh 18 120000h 12FFFFh 97 610000h 61FFFFh 57 390000h 39FFFFh 17 110000h 11FFFFh 96 600000h 60FFFFh 56 380000h 38FFFFh 16 100000h 10FFFFh 95 5F0000h 5FFFFFh 55 370000h 37FFFFh 15 0F0000h 0FFFFFh 94 5E0000h 5EFFFFh 54 360000h 36FFFFh 14 0E0000h 0EFFFFh 93 5D0000h 5DFFFFh 53 350000h 35FFFFh 13 0D0000h 0DFFFFh 92 5C0000h 5CFFFFh 52 340000h 34FFFFh 12 0C0000h 0CFFFFh 91 5B0000h 5BFFFFh 51 330000h 33FFFFh 11 0B0000h 0BFFFFh 90 5A0000h 5AFFFFh 50 320000h 32FFFFh 10 0A0000h 0AFFFFh 89 590000h 59FFFFh 49 310000h 31FFFFh 9 090000h 09FFFFh 88 580000h 58FFFFh 48 300000h 30FFFFh 8 080000h 08FFFFh 87 570000h 57FFFFh 47 2F0000h 2FFFFFh 7 070000h 07FFFFh 86 560000h 56FFFFh 46 2E0000h 2EFFFFh 6 060000h 06FFFFh 85 550000h 55FFFFh 45 2D0000h 2DFFFFh 5 050000h 05FFFFh 84 540000h 54FFFFh 44 2C0000h 2CFFFFh 4 040000h 04FFFFh 83 530000h 53FFFFh 43 2B0000h 2BFFFFh 3 030000h 03FFFFh 82 520000h 52FFFFh 42 2A0000h 2AFFFFh 2 020000h 02FFFFh 81 510000h 51FFFFh 41 290000h 29FFFFh 1 010000h 01FFFFh 80 500000h 50FFFFh 40 280000h 28FFFFh 0 000000h 00FFFFh 79 4F0000h 4FFFFFh 39 270000h 27FFFFh 78 4E0000h 4EFFFFh 38 260000h 26FFFFh 77 4D0000h 4DFFFFh 37 250000h 25FFFFh 76 4C0000h 4CFFFFh 36 240000h 24FFFFh 75 4B0000h 4BFFFFh 35 230000h 23FFFFh 74 4A0000h 4AFFFFh 34 220000h 22FFFFh 73 490000h 49FFFFh 33 210000h 21FFFFh 72 480000h 48FFFFh 32 200000h 20FFFFh Janauary 29, 2013 S25FL128P_00_12 S25FL128P 17 D at a S hee t 9. Parallel Mode (for 16-pin SO package only) The parallel mode provides 8 bits of input/output to increase factory production throughput at the customer manufacturing facilities. This function is recommended for increasing production throughput. Entering Parallel mode requires issuing the Enter Parallel Mode command (55h). After writing the Parallel Mode Entry command and pulling CS# high, the available commands are Read, Write Enable (WREN), Write Disable (WRDI), Page Program (PP), Sector Erase (SE), Bulk Erase (BE), Write Status Register (WRSR), Read Status Register (RDSR), Release from Deep Power Down/Release from Deep Power Down and Read Electronic Signature (RES), Deep Power Down (DP), Read Identification (RDID) and Read ID (READ_ID). The flash memory will remain in Parallel mode until either the Parallel Mode Exit command (45h) is issued, or until a power-down / power-up sequence has been completed, after which the flash memory will exit parallel mode automatically and switch back to serial mode (no power-down will be necessary to switch back to serial mode if the Parallel Mode Exit command is issued). In parallel mode, the maximum SCK clock frequency is limited to 6 MHz for Read Data Bytes and 10 MHz for other operations. PO[6-0] can be left unconnected if the Parallel Mode functions are not needed. Fast-Read command is not applicable in Parallel mode. 10. Accelerated Programming Operation The device offers accelerated program operations through the ACC function. This function is primarily intended to allow faster manufacturing throughput at the factory. If the system asserts VHH on this pin, the device uses the higher voltage on the pin to reduce the time required for program operations. Removing VHH from the WP#/ACC pin returns the device to normal operation. Note that the WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. In addition, the WP#/ ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. 18 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et 11. Command Definitions The host system must shift all commands, addresses, and data in and out of the device, beginning with the most significant bit. On the first rising edge of SCK after CS# is driven low, the device accepts the one-byte command on SI (all commands are one byte long), most significant bit first. Each successive bit is latched on the rising edge of SCK. Table 11.6 on page 38 lists the complete set of commands. Every command sequence begins with a one-byte command code. The command may be followed by address, data, both, or nothing, depending on the command. CS# must be driven high after the last bit of the command sequence has been written. The Read Data Bytes (READ), Read Status Register (RDSR), Read Data Bytes at Higher Speed (FAST_READ) and Read Identification (RDID) command sequences are followed by a data output sequence on SO. CS# can be driven high after any bit of the sequence is output to terminate the operation. The Page Program (PP), Sector Erase (SE), Bulk Erase (BE), Write Status Register (WRSR), Write Enable (WREN), or Write Disable (WRDI) commands require that CS# be driven high at a byte boundary, otherwise the command is not executed. Since a byte is composed of eight bits, CS# must therefore be driven high when the number of clock pulses after CS# is driven low is an exact multiple of eight. The device ignores any attempt to access the memory array during a Write Status Register, program, or erase operation, and continues the operation uninterrupted. 11.1 Read Data Bytes (READ: 03h) 11.1.1 Serial Mode The Read Data Bytes (READ-Serial Mode) command reads data from the memory array at the frequency (fSCK) presented at the SCK input, with a maximum speed of 40 MHz. The host system must first select the device by driving CS# low. The READ command is then written to SI, followed by a 3-byte address (A23-A0). Each bit is latched on the rising edge of SCK. The memory array data, at that address, are output serially on SO at a frequency fSCK, on the falling edge of SCK. Figure 11.1 and Table 11.6 detail the READ command sequence. The first byte specified can be at any location. The device automatically increments to the next higher address after each byte of data is output. The entire memory array can therefore be read with a single READ command. When the highest address is reached, the address counter reverts to 00000h, allowing the read sequence to continue indefinitely. The READ command is terminated by driving CS# high at any time during data output. The device rejects any READ command issued while it is executing a program, erase, or Write Status Register operation, and continues the operation uninterrupted. Figure 11.1 Read Data Bytes (READ) Command Sequence CS# Mode 3 SCK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 Mode 0 Command 24-Bit Address 23 22 21 SI 3 2 1 0 MSB SO Hi-Z Data Out 1 7 6 5 4 3 2 Data Out 2 1 0 7 MSB Janauary 29, 2013 S25FL128P_00_12 S25FL128P 19 D at a 11.1.2 S hee t Parallel Mode In parallel mode, the maximum SCK clock frequency is 6 MHz. The device requires a single clock cycle instead of eight clock cycles to access the next data byte. The memory array output will be the same as in the serial mode. The only difference is that a byte of data is output per clock cycle instead of a single bit. This means that 256 bytes of data can be copied into the 256 byte wide page write buffer in 256 clock cycles instead of in 2,048 clock cycles. Figure 11.2 Parallel Read Instruction Sequence CS# SCK 24-Bit Address Instruction SI Data Out PO[7-0] High Impedance Notes 1. 1st Byte = "03h". 2. 2nd Byte = Address 1, MSB first (bits 23 through 16). 3. 3rd Byte = Address 2, MSB first (bits 15 through 8). 4. 4th Byte = Address 3, MSB first (bits 7 through 0). 5. From the 5th Byte, SO will output the array data. 6. In parallel mode, the maximum clock frequency (Fsck) is 6 MHz. 7. For parallel mode operation, the device requires an Enter Parallel Mode command (55h) before the READ command. An Exit Parallel Mode (45h) command or a power-down / power-up sequence is required to exit the parallel mode. 20 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data 11.2 She et Read Data Bytes at Higher Speed (FAST_READ: 0Bh) The FAST_READ command reads data from the memory array at the frequency (fSCK) presented at the SCK input, with a maximum speed of 104 MHz. The host system must first select the device by driving CS# low. The FAST_READ command is then written to SI, followed by a 3-byte address (A23-A0) and a dummy byte. Each bit is latched on the rising edge of SCK. The memory array data, at that address, are output serially on SO at a frequency fSCK, on the falling edge of SCK. The FAST_READ command sequence is shown in Figure 11.3 and Table 11.6. The first byte specified can be at any location. The device automatically increments to the next higher address after each byte of data is output. The entire memory array can therefore be read with a single FAST_READ command. When the highest address is reached, the address counter reverts to 00000h, allowing the read sequence to continue indefinitely. The FAST_READ command is terminated by driving CS# high at any time during data output. The device rejects any FAST_READ command issued while it is executing a program, erase, or Write Status Register operation, and continues the operation uninterrupted. Note that the FAST_READ command is not valid in parallel mode. Figure 11.3 Read Data Bytes at Higher Speed (FAST_READ) Command Sequence CS# Mode 3 SCK 0 1 2 3 4 5 Command 7 8 9 10 28 29 30 31 32 33 24-Bit Address 23 22 21 SI SO 6 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Mode 0 3 2 Hi-Z Dummy Byte 1 0 7 6 5 4 3 2 1 0 7 MSB Janauary 29, 2013 S25FL128P_00_12 S25FL128P 6 5 4 3 DATA OUT 1 2 1 0 7 MSB DATA OUT 2 21 D at a 11.3 S hee t Read Identification (RDID: 9Fh) 11.3.1 Serial Mode The Read Identification (RDID) instruction opcode allows the 8-bit manufacturer identification to be read, follow by two bytes of device identification. The manufacturer identification is assigned by JEDEC. The device identification is assigned by the device manufacturer. Any Read Identification (RDID) instruction opcode issued while a program, erase, or write cycle is in progress is not decoded and has no effect on execution of the program, erase, or write cycle that is in progress. The device is first selected by driving the CS# chip select input pin to the logic low state. After this, the RDID 8-bit instruction opcode is shifted in onto the SI serial input pin. After the last bit of the RDID instruction opcode is shifted into the device, a byte of manufacturer identification, two bytes of device identification and two bytes of extended device identification will be shifted sequentially out of the SO serial output pin. Each bit is shifted out during the falling edge of the SCK serial clock signal. The maximum clock frequency for the RDID (9Fh) command is at 40 MHz (Normal Read). The Read Identification (RDID) instruction sequence is terminated by driving the CS# chip select input pin to the logic high state anytime during data output. After issuing any Read ID instruction opcodes (90h, 9Fh, ABh), driving the CS# chip select input pin to the logic high state will automatically send the device into the standby mode. Driving the CS# chip select input pin to the logic low state again will automatically send the device out of the standby mode and into the active mode. Figure 11.4 Read Identification Command Sequence and Data Out Sequence CS# 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 44 45 46 47 SCK Instruction SI Manufacturer / Device Identification SO 23 MSB 22 Extended Device Identification High Impedance S25FL128P 22 21 3 2 1 0 15 14 13 3 2 1 0 MSB S25FL128P_00_12 Janauary 29, 2013 Data 11.3.2 She et Parallel Mode In parallel mode, the maximum SCK clock frequency is 10 MHz. The device requires a single clock cycle instead of eight clock cycles to access the next data byte. The method of memory content output will be the same compared to the serial mode. The only difference is that a byte of data is output per clock cycle instead of a single bit. In this case, the manufacturer identification will be output during the first byte cycle and the device identification during the second and third byte cycles out of the PO7-PO0 serial output pins. To read ID in parallel mode requires a Parallel Mode Entry command (55h) to be issued before the RDID command. Once in the parallel mode, the flash memory will not exit parallel mode until a Parallel Mode Exit (45h) command is given to the flash device, or upon power down/power up sequence. Figure 11.5 Parallel Read_ID Command Sequence and Data Out Sequence CS# 0 1 2 3 4 5 6 7 8 9 10 11 12 SCK Instruction SI Manufacturer/Device Identification High Impedance Byte 0 PO[7-0] Byte 1 Byte 2 Byte 3 Byte 4 Table 11.1 Manufacturer & Device Identification, RDID (9Fh) Manufacturer Identification Device Device Identification Extended Device Identification Byte 0 Byte 1 Byte 2 Byte 3 Uniform 256 KB Sector 01h 20h 18h 03h 00h Uniform 64 KB Sector 01h 20h 18h 03h 01h Janauary 29, 2013 S25FL128P_00_12 S25FL128P Byte 4 23 D at a 11.4 S hee t Read Manufacturer and Device ID (READ_ID: 90h) 11.4.1 Serial Mode The READ_ID (90h) instruction identifies the Device Manufacturer ID and the Device ID. The instruction is initiated by driving the CS# pin low and shifting in (via the SI input pin) the instruction code "90h" followed by a 24-bit address of XXXXX0h. (X: High or Low) Following this, the Manufacturer ID and the Device ID are shifted out on SO output pin starting after the falling edge of the SCK serial clock input signal. The Manufacturer ID and the Device ID are always shifted out on the SO output pin with the MSB first, as shown in Figure 11.6. If the 24-bit address is set to XXXXX1h, then the Device ID is read out first followed by the Manufacturer ID. Note that the upper 23 bits of the address do not have to be 0's and can be don't cares. Once the device is in READ_ID mode, the Manufacturer ID and Device ID output data toggles between address 000000H and 000001H until terminated by a low to high transition on the CS# input pin. After the first 24-bit address is provided, the user must wait 16 clock cycles for both the Manufacturer ID and Device ID to be output on the SO output pin. The maximum clock frequency for the READ_ID (90h) command is at 104MHz (Fast Read). Parallel Mode the maximum clock frequency is 10 MHz. The Manufacturer ID & Device ID is output continuously until terminated by a low to high transition on CS# chip select input pin. After issuing READ_ID instruction, driving the CS# chip select input pin to the logic high state will automatically send the device into the standby mode. Driving the CS# chip select input pin to the logic low state again will automatically send the device out of the standby mode and into the active mode. Figure 11.6 Serial READ_ID Instruction Sequence CS# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 9 8 SCK Instruction 24-Bit Address SI 23 22 21 20 19 18 17 16 15 14 13 12 11 10 90h High Impedance High Impedance SO CS# 24 25 26 27 28 29 30 31 1 0 32 33 34 35 36 37 38 39 40 41 42 1 0 7 6 5 43 44 45 46 47 2 1 0 SCK 24-Bit Address SI 7 6 5 4 3 2 Manufacturer ID SO High Impedance 7 6 5 MSB 24 S25FL128P 4 3 2 Device ID 4 3 MSB S25FL128P_00_12 Janauary 29, 2013 Data 11.4.2 She et Parallel Mode The maximum clock frequency allowed on the SCK input pin in parallel mode is 10 MHz. The Parallel Mode Entry command (55h) must be issued before writing the READ_ID command. Once in the parallel mode, the flash memory will not exit parallel mode until a Parallel Mode Exit (45h) command is given to the flash device, or upon power-down/power-up sequence. Figure 11.7 Parallel Read_ID Instruction Sequence CS# 0 1 2 4 3 5 6 7 8 9 10 20 21 22 23 24 25 26 27 28 29 30 31 32 1 0 33 34 SCK 2 Dummy Bytes Instruction 15 14 13 SI 3 ADD (1) 2 1 0 7 6 5 4 3 2 MSB 90h High Impedance Byte 1 PO[7-0] Byte 2 Manufacture ID Device ID Table 11.2 READ_ID Command and Data 11.5 Description Address Data Manufacturer Identification 00000h 01h Device Identification (Memory Capacity) 00001h 17h Write Enable (WREN: 06h) The Write Enable (WREN) command (see Figure 11.8) sets the Write Enable Latch (WEL) bit to a 1, which enables the device to accept a Write Status Register, program, or erase command. The WEL bit must be set prior to every Page Program (PP), Erase (SE or BE) and Write Status Register (WRSR) command. The host system must first drive CS# low, write the WREN command, and then drive CS# high. Figure 11.8 Write Enable (WREN) Command Sequence CS# Mode 3 0 1 2 3 4 5 6 7 SCK Mode 0 Command SI SO/PO[7-0] Janauary 29, 2013 S25FL128P_00_12 Hi-Z S25FL128P 25 D at a 11.6 S hee t Write Disable (WRDI: 04h) The Write Disable (WRDI) command (see Figure 11.9) resets the Write Enable Latch (WEL) bit to a 0, which disables the device from accepting a Write Status Register, program, or erase command. The host system must first drive CS# low, write the WRDI command, and then drive CS# high. Any of following conditions resets the WEL bit: Power-up Write Disable (WRDI) command completion Write Status Register (WRSR) command completion Page Program (PP) command completion Sector Erase (SE) command completion Bulk Erase (BE) command completion Figure 11.9 Write Disable (WRDI) Command Sequence CS# Mode 3 0 1 2 3 4 5 6 7 SCK Mode 0 Command SI Hi-Z SO/PO[7-0] 11.7 Read Status Register (RDSR: 05h) 11.7.1 Serial Mode The Read Status Register (RDSR) command outputs the state of the Status Register bits. Table 11.3 shows the status register bits and their functions. The RDSR command may be written at any time, even while a program, erase, or Write Status Register operation is in progress. The host system should check the Write In Progress (WIP) bit before sending a new command to the device if an operation is already in progress. Figure 11.10 shows the RDSR command sequence, which also shows that it is possible to read the Status Register continuously until CS# is driven high. Table 11.3 S25FL128P Status Register (Uniform 256 KB sector) Bit Status Register Bit Bit Function 7 SRWD Status Register Write Disable 6 Don't Care -- -- 5 0 -- Not used 4 BP2 3 BP1 2 BP0 1 WEL Write Enable Latch 0 WIP Write in Progress Block Protect Description 1 = Protects when WP#/ACC is low 0 = No protection, even when WP#/ACC is low 000-111 = Protects upper half of address range in 7 sizes. 1 = Device accepts Write Status Register, program, or erase commands 0 = Ignores Write Status Register, program, or erase commands 1 = Device Busy. A Write Status Register, program, or erase operation is in progress 0 = Ready. Device is in standby mode and can accept commands. 26 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Table 11.4 S25FL128P Status Register (Uniform 64 KB sector) Bit Status Register Bit Bit Function Description 7 SRWD Status Register Write Disable 6 Don't Care -- 5 BP3 4 BP2 3 BP1 2 BP0 1 WEL Write Enable Latch 0 WIP Write in Progress 1 = Protects when WP#/ACC is low 0 = No protection, even when WP#/ACC is low -- Block Protect 0000-1111= Protects upper half of address range in 8 sizes. 1 = Device accepts Write Status Register, program, or erase commands 0 = Ignores Write Status Register, program, or erase commands 1 = Device Busy. A Write Status Register, program, or erase operation is in progress 0 = Ready. Device is in standby mode and can accept commands. Figure 11.10 Read Status Register (RDSR) Command Sequence CS# Mode 3 SCK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 0 Command SI SO Hi-Z 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 MSB Janauary 29, 2013 S25FL128P_00_12 Status Register Out S25FL128P MSB Status Register Out 27 D at a 11.7.2 S hee t Parallel Mode When the device is in Parallel Mode, the maximum SCK clock frequency is 10 MHz. The device requires a single clock cycle instead of eight clock cycles to access the next data byte. The method of memory content output will be the same compared to outside of Parallel Mode. The only difference is that a byte of data is output per clock cycle instead of a single bit. The Status Register contents can be read out on the PO[7-0] serial output pins continuously by applying multiples of clock cycles. Figure 11.11 Parallel Read Status Register (RDSR) Instruction Sequence CS# Mode 3 SCK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Mode 0 Command SI PO[7-0] Hi-Z Byte Byte 1 2 Status Register Out Byte n Notes 1. Instruction byte = 05h. 2. Under parallel mode, the fastest access clock frequency (Fsck) will be changed to a maximum of 10MHz (SCK pin clock frequency). 3. To read Status Register in parallel mode requires a Parallel Mode Entry command (55h) to be issued before the RDSR command. Once in the parallel mode, the flash memory will not exit the parallel mode until a Parallel Mode Exit (45h) command is given to the flash device, or upon power down / power up sequence. 11.7.3 Status Register Bit Descriptions The following describes the status and control bits of the Status Register, and applies to both serial and parallel modes. Write In Progress (WIP) bit: Indicates whether the device is busy performing a Write Status Register, program, or erase operation. This bit is read-only, and is controlled internally by the device. If WIP is 1, one of these operations is in progress; if WIP is 0, no such operation is in progress. Write Enable Latch (WEL) bit: Determines whether the device will accept and execute a Write Status Register, program, or erase command. When set to 1, the device accepts these commands; when set to 0, the device rejects the commands. This bit is set to 1 by writing the WREN command, and set to 0 by the WRDI command, and is also automatically reset to 0 after the completion of a Write Status Register, program, or erase operation. WEL cannot be directly set by the WRSR command. Block Protect (BP2, BP1, BP0) bits for uniform 256KB sector product: (BP3, BP2, BP1, BP0) for uniform 64KB sector product: Define the portion of the memory area that will be protected against any changes to the stored data. The Write Status Register (WRSR) command controls these bits, which are nonvolatile. When one or more of these bits is set to 1, the corresponding memory area (see Table 7.1 on page 13) is protected against Page Program (PP) and Sector Erase (SE) commands. If the Hardware Protected mode is enabled, BP2:BP0 (or BP3:BP0) cannot be changed. The Bulk Erase (BE) command is executed only if all Block Protect bits are 0. Status Register Write Disable (SRWD) bit: Provides data protection when used together with the Write Protect (WP#/ACC) signal. When SRWD is set to 1 and WP#/ACC is driven low, the device enters the Hardware Protected mode. The non-volatile bits of the Status Register (SRWD, BP2, BP1, BP0) become read-only bits and the device ignores any Write Status Register (WRSR) command. 28 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data 11.8 She et Write Status Register (WRSR: 01h) The Write Status Register (WRSR) command changes the bits in the Status Register. A Write Enable (WREN) command, which itself sets the Write Enable Latch (WEL) in the Status Register, is required prior to writing the WRSR command. Table 11.3, S25FL128P Status Register (Uniform 256 KB sector) on page 26 shows the status register bits and their functions. The host system must drive CS# low, write the WRSR command, and the appropriate data byte on SI (Figure 11.12). The WRSR command cannot change the state of the Write Enable Latch (bit 1). The WREN command must be used for that purpose. Bit 0 is a status bit controlled internally by the Flash device. Bits 6 and 5 are always read as 0 and have no user significance. The WRSR command also controls the value of the Status Register Write Disable (SRWD) bit. The SRWD bit and WP#/ACC together place the device in the Hardware Protected Mode (HPM). The device ignores all WRSR commands once it enters the Hardware Protected Mode (HPM). Table 11.5 shows that WP#/ACC must be driven low and the SRWD bit must be 1 for this to occur. Figure 11.12 Write Status Register (WRSR) Command Sequence CS# Mode 3 1 0 2 4 3 9 10 11 12 13 14 15 8 7 6 5 SCK Mode 0 Command Status Register In 7 SI 6 5 4 3 2 1 0 MSB SO Hi-Z Figure 11.13 Parallel Write Status Register (WRSR) Command Sequence CS# Mode 3 SCK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 0 Command Status Register In SI Byte 1 PO[7-0] Hi-Z Notes 1. Instruction byte = 01h 2. In parallel mode, the maximum access clock frequency (Fsck) is 10 MHz (SCK pin clock frequency). 3. Writing to the Status Register in parallel mode requires a Parallel Mode Entry command (55h) to be issued before the WRSR command. Once in the parallel mode, the flash memory will not exit the parallel mode until a Parallel Mode Exit (45h) command is given to the flash device, or upon power-down or power-up sequence. Janauary 29, 2013 S25FL128P_00_12 S25FL128P 29 D at a S hee t Table 11.5 Protection Modes WP#/ACC Signal SRWD Bit 1 1 1 0 0 0 0 1 Mode Write Protection of the Status Register Protected Area (See Note) Unprotected Area (See Note) Software Protected (SPM) Status Register is writable (if the WREN command has set the WEL bit). The values in the SRWD, BP2, BP1 and BP0 (or BP3, BP2, BP1 and BP0) bits can be changed. Protected against program and erase commands Ready to accept Page Program and Sector Erase commands Hardware Protected (HPM) Status Register is Hardware write protected. The values in the SRWD, BP2, BP1 and BP0 (or BP3, BP2, BP1 and BP0) bits cannot be changed. Protected against program and erase commands Ready to accept Page Program and Sector Erase commands Note As defined by the values in the Block Protect (BP2, BP1, BP0) bits of the Status Register, as shown in Table 7.1 on page 13. Table 11.5 shows that neither WP#/ACC or SRWD bit by themselves can enable HPM. The device can enter HPM either by setting the SRWD bit after driving WP#/ACC low, or by driving WP#/ACC low after setting the SRWD bit. However, the device disables HPM only when WP#/ACC is driven high. Note that HPM only protects against changes to the status register. Since BP2:BP0 (or BP3:BP0) cannot be changed in HPM, the size of the protected area of the memory array cannot be changed. Note that HPM provides no protection to the memory array area outside that specified by Block Protect bits (Software Protected Mode, or SPM). If WP#/ACC is permanently tied high, HPM can never be activated, and only the SPM (Block Protect bits of the Status Register) can be used. 11.9 Page Program (PP: 02h) 11.9.1 Serial Mode The Page Program (PP) command changes specified bytes in the memory array (from 1 to 0 only). A WREN command is required prior to writing the PP command. The host system must drive CS# low, and then write the PP command, three address bytes, and at least one data byte on SI. CS# must be driven low for the entire duration of the PP sequence. The command sequence is shown in Figure 11.14 and Table 11.6. The device programs only the last 256 data bytes sent to the device. If the number of data bytes exceeds this limit, the bytes sent before the last 256 bytes are discarded, and the device begins programming the last 256 bytes sent at the starting address of the specified page. This may result in data being programmed into different addresses within the same page than expected. If fewer than 256 data bytes are sent to device, they are correctly programmed at the requested addresses. The host system must drive CS# high after the device has latched the 8th bit of the data byte, otherwise the device does not execute the PP command. The PP operation begins as soon as CS# is driven high. The device internally controls the timing of the operation, which requires a period of tPP. The Status Register may be read to check the value of the Write In Progress (WIP) bit while the PP operation is in progress. The WIP bit is 1 during the PP operation, and is 0 when the operation is completed. The device internally resets the Write Enable Latch to 0 before the operation completes (the exact timing is not specified). The device does not execute a Page Program (PP) command that specifies a page that is protected by the Block Protect bits (see Table 7.1 on page 13). 30 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Figure 11.14 Page Program (PP) Command Sequence CS# 0 Mode 3 5 4 3 6 8 7 28 29 30 31 32 33 34 35 36 37 38 9 10 39 Mode 0 24-Bit Address 3 23 22 21 2 1 0 MSB 6 5 4 3 2 1 0 2078 2079 2076 55 2077 51 52 53 54 2072 MSB CS# 40 41 42 43 44 45 46 47 48 49 50 7 2075 SI Data Byte 1 2074 Command 2073 SCK 2 1 SCK Data Byte 2 SI 7 MSB Janauary 29, 2013 S25FL128P_00_12 6 5 4 3 2 Data Byte 3 1 0 7 6 5 4 MSB S25FL128P 3 2 Data Byte 256 1 0 7 6 5 4 3 2 1 0 MSB 31 D at a 11.9.2 S hee t Parallel Mode In parallel mode, the maximum SCK clock frequency is 10 MHz. The device requires a single clock cycle instead of eight clock cycles to access the next data byte. The memory content input method is the same as serial mode. The only difference is that a byte of data is input per clock cycle instead of a single bit. This means that 256 bytes of data can be copied into the 256 byte wide page write buffer in 256 clock cycles instead of in 2,048 clock cycles. Figure 11.15 Parallel Page Program (PP) Instruction Sequence CS# 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 23 24 31 32 33 n SCK Address Byte 1 Instruction (02h) 23 22 21 20 SI 19 18 17 16 15 Address Byte 2 Address Byte 3 8 7 0 MSB 90h High-Z Byte 1 PO[7-0] Byte 2 Byte n Hi-Z Notes 1. 1st Byte = "02h". 2. 2nd Byte = Address 1, MSB first (bits 23 through 16). 3. 3rd Byte = Address 2, MSB first (bits 15 through 8). 4. 4th Byte = Address 3, MSB first (bits 7 through 0). 5. 5th Byte = first write data byte. 6. In parallel mode, the fastest access clock frequency (Fsck) is 10 MHz (SCK pin clock frequency). 7. Programming in parallel mode requires an "Parallel mode Entry" command (55h) before the program command. Once in the parallel mode, the flash memory will not exit parallel mode until an "Exit Parallel Mode" (45h) command is given to the flash device, or upon power down / power up sequence completion. 32 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et 11.10 Sector Erase (SE: 20h, D8h) The Sector Erase (SE) command sets all bits at all addresses within a specified sector to a logic 1. A WREN command is required prior to writing the SE command. The host system must drive CS# low, and then write the SE command plus three address bytes on SI. Any address within the sector (see Table 7.1 on page 13) is a valid address for the SE command. CS# must be driven low for the entire duration of the SE sequence. The command sequence is shown in Figure 11.16 and Table 11.6. The host system must drive CS# high after the device has latched the 24th bit of the Address input, otherwise the device does not execute the command. The SE operation begins as soon as CS# is driven high. The device internally controls the timing of the operation, which requires a period of tSE. The Status Register may be read to check the value of the Write In Progress (WIP) bit while the SE operation is in progress. The WIP bit is 1 during the SE operation, and is 0 when the operation is completed. The device internally resets the Write Enable Latch to 0 before the operation completes (the exact timing is not specified). The device does not execute an SE command that specifies a sector that is protected by the Block Protect bits (see Table 7.1 on page 13). Figure 11.16 Sector Erase (SE) Command Sequence CS# Mode 3 SCK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 1 0 Mode 0 Command SI 24-bit Address 23 22 21 3 2 MSB SO/PO[7-0] Hi-Z Janauary 29, 2013 S25FL128P_00_12 S25FL128P 33 D at a S hee t 11.11 Bulk Erase (BE: C7h, 60h) The Bulk Erase (BE) command sets all the bits within the entire memory array to logic 1s. A WREN command is required prior to writing the BE command. For 64 KB sector devices, the bulk erase command may be written as either C7h or 60h. For 256 KB sector devices, only the C7h command is valid. The host system must drive CS# low, and then write the BE command on SI. CS# must be driven low for the entire duration of the BE sequence. The command sequence is shown in Figure 11.17 and Table 11.6. The host system must drive CS# high after the device has latched the 8th bit of the BE command, otherwise the device does not execute the command. The BE operation begins as soon as CS# is driven high. The device internally controls the timing of the operation, which requires a period of tBE. The Status Register may be read to check the value of the Write In Progress (WIP) bit while the BE operation is in progress. The WIP bit is 1 during the BE operation, and is 0 when the operation is completed. The device internally resets the Write Enable Latch to 0 before the operation completes (the exact timing is not specified). The device only executes a BE command if all Block Protect bits (BP2:BP0 or BP3:BP0) are 0 (see Table 7.1 on page 13). Otherwise, the device ignores the command. Figure 11.17 Bulk Erase (BE) Command Sequence CS# Mode 3 SCK 0 1 2 3 4 5 6 7 Mode 0 Command SI SO/PO[7-0] 34 Hi-Z S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et 11.12 Deep Power Down (DP: B9h) The Deep Power Down (DP) command provides the lowest power consumption mode of the device. It is intended for periods when the device is not in active use, and ignores all commands except for the Release from Deep Power Down (RES) command. The DP mode therefore provides the maximum data protection against unintended write operations. The standard standby mode, which the device goes into automatically when CS# is high (and all operations in progress are complete), should generally be used for the lowest power consumption when the quickest return to device activity is required. The host system must drive CS# low, and then write the DP command on SI. CS# must be driven low for the entire duration of the DP sequence. The command sequence is shown in Figure 11.18 and Table 11.6. The host system must drive CS# high after the device has latched the 8th bit of the DP command, otherwise the device does not execute the command. After a delay of tDP, the device enters the DP mode and current reduces from ISB to IDP (see Table 17.1 on page 41). Once the device has entered the DP mode, all commands are ignored except the RES command (which releases the device from the DP mode). The RES command also provides the Electronic Signature of the device to be output on SO, if desired (see sections 11.13 and 11.14). DP mode automatically terminates when power is removed, and the device always powers up in the standard standby mode. The device rejects any DP command issued while it is executing a program, erase, or Write Status Register operation, and continues the operation uninterrupted. Figure 11.18 Deep Power Down (DP) Command Sequence CS# tDP Mode 3 SCK 0 1 2 3 4 5 6 7 Mode 0 Command SI SO/PO[7-0] Hi-Z Standby Mode Janauary 29, 2013 S25FL128P_00_12 S25FL128P Deep Power-down Mode 35 D at a S hee t 11.13 Release from Deep Power Down (RES: ABh) The device requires the Release from Deep Power Down (RES) command to exit the Deep Power Down mode. When the device is in the Deep Power Down mode, all commands except RES are ignored. The host system must drive CS# low and write the RES command to SI. CS# must be driven low for the entire duration of the sequence. The command sequence is shown in Figure 11.19 and Table 11.6. The host system must drive CS# high tRES(max) after the 8-bit RES command byte. The device transitions from DP mode to the standby mode after a delay of tRES (see Table 19.1 on page 43). In the standby mode, the device can execute any read or write command. Figure 11.19 Release from Deep Power Down (RES) Command Sequence CS# Mode 3 SCK 0 1 2 3 4 5 6 7 Mode 0 Command tRES SI SO/PO[7-0] Hi-Z Deep Power-down Mode Standby Mode 11.14 Release from Deep Power Down and Read Electronic Signature (RES: ABh) 11.14.1 Serial Mode This command reads the old-style Electronic Signature from the SO serial output pin. See Figure 11.20 and Table 11.6 for the command sequence and signature value. Please note that the Electronic Signature only consists of the Device ID portion of the 16-bit JEDEC ID that is read by the Read Identifier (RDID) instruction. The old style Electronic Signature is supported for backward compatibility, and should not be used for new software designs, which should instead use the JEDEC 16-bit Electronic Signature by issuing the Read Identifier (RDID) command. The device is first selected by driving the CS# chip select input pin to the logic low state. The RES command is shifted in followed by three dummy bytes onto the SI serial input pin. After the last bit of the three dummy bytes is shifted into the device, a byte of Electronic Signature will be shifted out of the SO serial output pin. Each bit is shifted out during the falling edge of the SCK serial clock signal. The maximum clock frequency for the RES (ABh) command is at 104 MHz. The Electronic Signature can be read repeatedly by applying multiples of eight clock cycles. The RES instruction sequence is terminated by driving the CS# chip select input pin to the logic high state anytime during data output. After issuing any Read ID commands (90h, 9Fh, ABh), driving the CS# chip select input pin to the logic high state will automatically send the device into the standby mode. Driving the CS# chip select input pin to the logic low state again will automatically send the device out of the standby mode and into the active mode. 36 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Figure 11.20 Serial Release from Deep Power Down and Read Electronic Signature (RES) Command Sequence CS# 0 1 2 3 4 5 6 7 8 9 28 29 30 31 32 33 34 35 36 37 38 10 SCK tRES 3 Dummy Bytes Command SI 3 23 22 21 1 2 0 MSB Hi-Z SO 7 6 MSB 5 4 3 2 1 0 Electronic ID out Standby Mode Deep Power-down Mode 11.14.2 Parallel Mode When the device is in parallel mode, the maximum SCK clock frequency is 10 MHz. The device requires a single clock cycle instead of eight clock cycles to access the next data byte. The method of memory content output will be the same compared to outside of parallel mode. The only difference is that a byte of data is output per clock cycle instead of a single bit. In this case, the Electronic Signature will be output onto the P0[7-0] parallel output pins. Figure 11.21 Parallel Release from Deep Power Down and Read Electronic Signature (RES) Command Sequence CS# 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 SCK SI tRES 3 Dummy Bytes Command 23 22 21 3 2 1 0 MSB PO[7-0] Hi-Z Electronic ID Byte 1 Deep Power-down Mode Standby Mode Notes 1. In parallel mode, the maximum access clock frequency (Fsck) is 10 MHz (SCK pin clock frequency). 2. To release the device from Deep Power Down and read Electronic ID in parallel mode, a Parallel Mode Enter command (55h) must be issued before the RES command. The device will not exit parallel mode until a Parallel Mode Exit command (45h) is written, or upon power-down or power-up sequence. 3. Byte 1 will output the Electronic Signature. Janauary 29, 2013 S25FL128P_00_12 S25FL128P 37 D at a S hee t 11.15 Command Definitions Table 11.6 Command Definitions Operation One-Byte Command Code Address Bytes Dummy Byte Read Data Bytes 03h (0000 0011) 3 0 1 to Read Data Bytes at Higher Speed 0Bh (0000 1011) 3 1 1 to Command Description READ FAST_READ Data Bytes Read RDID Read Identification 9Fh (1001 1111) 0 0 1 to 3 Read Manufacturer ID and Device ID 90h (1001 0000) 3 0 1 to WREN Write Enable 06h (0000 0110) 0 0 0 WRDI Write Disable 04h (0000 0100) 0 0 0 20h (0010 0000) or D8h (1101 1000) 3 0 0 READ_ID Write Control 64 KB Sector Erase (See Note) SE 256 KB Sector Erase Erase D8h (1101 1000) 3 0 0 Bulk (Chip) Erase, Uniform 64 KB Sector Product (See Note) C7h (1100 0111) or 60h (0110 0000) 0 0 0 Bulk (Chip) Erase, Uniform 256 KB Sector Product C7h (1100 0111) 0 0 0 BE Program Page Program 02h (0000 0010) 3 0 1 to 256 RDSR PP Read from Status Register 05h (0000 0101) 0 0 1 to WRSR Write to Status Register 01h (0000 0001) 0 0 1 Entry 0 Status Register Enter x8 Parallel Mode 55h (0101 0101) 0 0 Exit Exit x8 Parallel Mode 45h (0100 0101) 0 0 0 DP Deep Power Down B9h (1011 1001) 0 0 0 Release from Deep Power Down ABh (1010 1011) 0 0 0 Release from Deep Power Down and Read Electronic Signature ABh (1010 1011) 0 3 1 to Parallel Mode Power Saving RES Note For 64 KB sector devices, either command is valid and performs the same function. 12. Program Acceleration via WP#/ACC pin The program acceleration function requires applying VHH to the WP#/ACC input, and then waiting a period of tWC. Minimum tVHH rise and fall times is required for WP#/ACC to change to VHH from VIL or VIH. Removing VHH from the WP#/ACC pin returns the device to normal operation after a period of tWC. Figure 12.1 ACC Program Acceleration Timing Requirements VHH tWC ACC tWC VIL or VIH VIL or VIH tVHH tVHH Command OK Command OK Note Only Read Status Register (RDSR) and Page Program (PP) operations are allow when ACC is at (VHH). Table 12.1 ACC Program Acceleration Specifications Parameter 38 Description Min. Max. 9.5 Unit VHH ACC Pin Voltage High 8.5 tVHH ACC Voltage Rise and Fall Time 250 ns tWC ACC at VHH and VIL or VIH to First command 5 ns S25FL128P V S25FL128P_00_12 Janauary 29, 2013 Data She et 13. Power-up and Power-down During power-up and power-down, certain conditions must be observed. CS# must follow the voltage applied on VCC, and must not be driven low to select the device until VCC reaches the allowable values as follows (see Figure 13.1 and Table 13.1): At power-up, VCC (min.) plus a period of tPU At power-down, VSS A pull-up resistor on Chip Select (CS#) typically meets proper power-up and power-down requirements. No Write Status Register, program, or erase command should be sent to the device until VCC rises to the VCC minimum, plus a delay of tPU. At power-up, the device is in standby mode (not Deep Power Down mode) and the WEL bit is reset (0). Each device in the host system should have the VCC rail decoupled by a suitable capacitor close to the package pins (this capacitor is generally of the order of 0.1 F), as a precaution to stabilizing the VCC feed. When VCC drops from the operating voltage to below the minimum VCC threshold at power-down, all operations are disabled and the device does not respond to any commands. Note that data corruption may result if a power-down occurs while a Write Register, program, or erase operation is in progress. Figure 13.1 Power-Up Timing Diagram Vcc (max) Vcc (min) Vcc t PU Full Device Access Time Figure 13.2 Power-down and Voltage Drop Vcc VCC (max) No Device Access Allowed VCC (min) tPU VCC (cut-off) Device Access Allowed VCC (low) tPD Time Janauary 29, 2013 S25FL128P_00_12 S25FL128P 39 D at a S hee t Table 13.1 Power-Up / Power-Down Voltage and Timing Symbol VCC(min) VCC(cut-off) VCC(low) Parameter Min Max Unit VCC (minimum operation voltage) 2.7 V VCC (Cut off where re-initialization is needed) 2.4 V VCC (Low voltage for initialization to occur at read/standby) VCC (Low voltage for initialization to occur at embedded) 0.2 tPU VCC (min) to device operation tPD VCC (low duration time) V 2.3 300 1.0 s s 14. Initial Delivery State The device is delivered with all bits set to 1 (each byte contains FFh) upon initial factory shipment. The Status Register contains 00h (all Status Register bits are 0). 15. Absolute Maximum Ratings Do not stress the device beyond the ratings listed in this section, or serious, permanent damage to the device may result. These are stress ratings only and device operation at these or any other conditions beyond those indicated in this section and in the Operating Ranges section of this document is not implied. Device operation for extended periods at the limits listed in this section may affect device reliability. Table 15.1 Absolute Maximum Ratings Description Rating Ambient Storage Temperature -65C to +150C -0.5V to VCC+0.5V Voltage with Respect to Ground: All Inputs and I/Os Notes 1. Minimum DC voltage on input or I/O pins is -0.5 V. During voltage transitions, input at I/O pins may overshoot VSS to -2.0V for periods of up to 20 ns. See Figure 15.2. Maximum DC voltage on output and I/O pins is 3.6 V. During voltage transitions output pins may overshoot to VCC + 2.0V for periods up to 20 ns. See Figure 15.2. 2. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. 3. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. Figure 15.1 Maximum Negative Overshoot Waveform 20 ns 20 ns +0.8 V -0.5 V -2 V 20 ns 40 S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Figure 15.2 Maximum Positive Overshoot Waveform 20 ns V CC +2.0 V V CC +0.5 V 2.0 V 20 ns 20 ns 16. Operating Ranges Table 16.1 Operating Ranges Description Rating Ambient Operating Temperature (TA) Industrial Positive Power Supply Voltage Range -40C to +85C 2.7V to 3.6 V Note Operating ranges define those limits between which functionality of the device is guaranteed. 17. DC Characteristics This section summarizes the DC Characteristics of the device. Designers should check that the operating conditions in their circuit match the measurement conditions specified in the Test Specifications in Table 18.1 on page 42, when relying on the quoted parameters. Table 17.1 DC Characteristics (CMOS Compatible) Parameter VCC Description Test Conditions (See Note) Typ. Unit 3.6 V 104 MHz (Serial) 22 mA 40 MHz (Serial: Fast Read Mode) 10 mA 3 MHz (Parallel Mode) 10 mA 2.7 SCK = 0.1 VCC/ 0.9VCC ICC1 Max Supply Voltage Min Active Read Current SCK = 0.1 VCC/ 0.9VCC ICC2 Active Page Program Current CS# = VCC 26 mA ICC3 Active WRSR Current CS# = VCC 26 mA ICC4 Active Sector Erase Current CS# = VCC 26 mA ICC5 Active Bulk Erase Current CS# = VCC 26 mA 200 A 20 A ISB Standby Current VIN = GND or VCC, CS# = VCC IDP Deep Power Down Current VIN = GND or VCC, CS# = VCC ILI Input Leakage Current VIN = GND or VCC, VCC = VCCmax 2 A ILO Output Leakage Current VIN = GND to VCC, VCC = VCCmax 2 A 3 VIL Input Low Voltage -0.3 0.3 VCC V VIH Input High Voltage 0.7 VCC VCC + 0.5 V VOL Output Low Voltage IOL = 1.6 mA, VCC = VCC min 0.4 V VOH Output High Voltage IOH = -0.1 mA VCC - 0.6 V Note Typical values are at TA = 25C and 3.0 V. Janauary 29, 2013 S25FL128P_00_12 S25FL128P 41 D at a S hee t 18. Test Conditions Figure 18.1 AC Measurements I/O Waveform 0.8 VCC 0.7 VCC 0.5 VCC 0.3 VCC Input Levels 0.2 VCC Input and Output Table 18.1 Test Specifications Symbol Parameter CL Load Capacitance Min Max 30 Input Rise and Fall Times 42 Unit pF 5 ns Input Pulse Voltage 0.2 VCC to 0.8 VCC V Input Timing Reference Voltage 0.3 VCC to 0.7 VCC V Output Timing Reference Voltage 0.5 VCC V S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et 19. AC Characteristics Table 19.1 AC Characteristics Symbol Parameter Min Typ (Notes) Max (Notes) Unit FSCK SCK Clock Frequency READ, RDID command D.C. 40 (Serial) 6 (Parallel) FSCK SCK Clock Frequency for: FAST_READ, READ_ID, PP, SE, BE, DP, RES, WREN, WRDI, RDSR, WRSR (Note 4) D.C. 104 (Serial) 10 (Parallel) tCRT Clock Rise Time (Slew Rate) 0.1 (Serial) 0.25 (Parallel) V/ns tCFT Clock Fall Time (Slew Rate) 0.1 (Serial) 0.25 (Parallel) V/ns tWH SCK High Time 4.5 (Serial) 50 (Parallel) ns tWL SCK Low Time 4.5 (Serial) 50 (Parallel) ns tCS CS# High Time 50 (Serial) 20 (Parallel) ns MHz MHz tCSS CS# Setup Time (Note 3) 3 ns tCSH CS# HOLD Time (Note 3) 3 ns tHD HOLD# Setup Time (relative to SCK) (Note 3) 3 ns tCD HOLD# Non-Active Hold Time (relative to SCK) (Note 3) 3 ns tHC HOLD# Non-Active Setup Time (relative to SCK) 3 ns tCH HOLD# Hold Time (relative to SCK) 3 ns Output Valid 0 tV tHO 8 (Serial) 20 (Parallel) ns Output Hold Time 2 ns tHD:DAT Data in Hold Time 2 (Serial) 10 (Parallel) ns tSU:DAT Data in Setup Time 3 (Serial) 10 (Parallel) ns tR Input Rise Time 5 ns tF Input Fall Time 5 ns ns tLZ HOLD# to Output Low Z (Note 3) 8 (Serial) 20 (Parallel) tHZ HOLD# to Output High Z (Note 3) 8 (Serial) 20 (Parallel) ns tDIS Output Disable Time (Note 3) 8 (Serial) 20 (Parallel) ns tWPS Write Protect Setup Time (Notes 3, 5) 20 ns tWPH Write Protect Hold Time (Notes 3, 5) 100 ns tW Write Status Register Time tDP CS# High to Deep Power Down Mode 3 s tRES Release DP Mode 30 s ms 100 ms tPP Page Programming Time 1.2 (Note 1) 3 (Note 2) tEP Page Programming Time (WP#/ACC = 9 V) 1.02 (Note 6) 2.4 (Note 2) ms tSE Sector Erase Time (64 KB) 0.5 (Note 1) 3 (Note 2) sec tSE Sector Erase Time (256 KB) 2 (Note 1) 12 (Note 2) sec tBE Bulk Erase Time 128 (Note 1) 768 (Note 2) sec Notes 1. Typical program and erase times assume the following conditions: 25C, VCC = 3.0 V; 10,000 cycles; checkerboard data pattern 2. Under worst-case conditions of 90C; VCC = 2.7V; 100,000 cycles 3. Not 100% tested. 4. FAST_READ is not valid in parallel mode. 5. Only applicable as a constraint for WRSR command when SRWD is set to a `1'. 6. For "00" data pattern at 25C. Janauary 29, 2013 S25FL128P_00_12 S25FL128P 43 D at a 19.1 S hee t Capacitance Symbol CIN COUT Parameter Test Conditions Input Capacitance (applies to SCK, PO7-PO0, SI, CS#) Output Capacitance (applies to PO7-PO0, SO) Min Typ Max Unit VOUT = 0V 9.0 12.0 pF VIN = 0V 12.0 16.0 pF Figure 19.1 SPI Mode 0 (0,0) Input Timing tCS CS# tCSH tCSS tCSH tCSS SCK tSU:DAT tHD:DAT tCRT SI tCFT MSB IN SO LSB IN Hi-Z Figure 19.2 SPI Mode 0 (0,0) Output Timing CS# tWH SCK tV tHO tWL tV SO 44 tDIS tHO LSB OUT S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Figure 19.3 HOLD# Timing CS# tCH tHC tHD SCK tCD tHZ tLZ SO SI HOLD# Figure 19.4 Write Protect Setup and Hold Timing during WRSR when SRWD=1 WP#/ACC tWPS tWPH CS# SCK SI SO Janauary 29, 2013 S25FL128P_00_12 Hi-Z S25FL128P 45 D at a S hee t 20. Physical Dimensions 20.1 46 SO3 016 wide -- 16-pin Plastic Small Outline Package (300-mil Body Width) S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data 20.2 She et WNF008 -- WSON 8-contact (6 x 8 mm) No-Lead Package NOTES: PACKAGE SYMBOL WNF008 MIN e 2. ALL DIMENSIONS ARE IN MILLMETERS. N IS THE TOTAL NUMBER OF TERMINALS. 4 DIMENSION "b" APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30mm FROM TERMINAL TIP. IF THE TERMINAL HAS THE OPTIONAL RADIUS ON THE OTHER END OF THE TERMINAL, THE DIMENSION "b" SHOULD NT BE MEASURED IN THAT RADIUS AREA. 5 ND REFER TO THE NUMBER OF TERMINALS ON D SIDE. 6. MAX. PACKAGE WARPAGE IS 0.05mm. 6.00 BSC 7. MAXIMUM ALLOWABLE BURRS IS 0.076mm IN ALL DIRECTIONS. 8.00 BSC 8 PIN #1 ID ON TOP WILL BE LASER MARKED. 9 BILATERAL COPLANARITY ZONE APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 10 A MAXIMUM 0.15mm PULL BACK (L1) MAY BE PRESENT. MAX NOTE N 8 3 ND 4 5 L 0.45 0.50 0.55 b 0.35 0.40 0.45 D2 4.70 4.80 4.90 E2 5.70 5.80 5.90 E A 0.70 0.75 0.80 A1 0.00 0.02 0.05 K L1 4 0.20 MIN. 0.00 DIMENSIONING AND TOLERANCING CONFORMS TO ASME Y14.5M - 1994. 3. NOM 1.27 BSC. D 1. --- 0.15 10 g1015 \ 16-038.30 \ 07.21.11 Janauary 29, 2013 S25FL128P_00_12 S25FL128P 47 D at a S hee t 21. Revision History Section Description Revision 01 (January 12, 2007) Initial release Revision 02 (March 13, 2007) Distinctive Characteristics Changed standby mode current S25FL128P Sector Address Table (Uniform 64 KB sector) Corrected addresses for sectors 0 and 32 Parallel Mode (for 16-pin SO package only) Added last sentence in section Read Status Register (RDSR: 05h) Separated status register bit descriptions into an additional subsection Page Program (PP: 02h) Modified Parallel Page Program (PP) Instruction Sequence figure to match format of other parallel mode figures Command Definitions Changed code for Bulk Erase (BE) 256 KB product in table Read Manufacturer and Device ID (READ_ID: 90h) Corrected SI and CLK in Parallel Read_ID Instruction Sequence figure Absolute Maximum Ratings Added overshoot and undershoot information DC Characteristics Changed maximum specifications for ICC1 (parallel mode), ISB, and IDP Revision 03 (April 24, 2007) Ordering Information Changed Valid Combinations table Revision 04 (July 2, 2007) Device Operations Added a sentence to Byte or Page programming Parallel Mode (for 16-pin SO package only) Added a sentence Revision 05 (November 4, 2008) Ordering Information AC Characteristics Added Tray package type option Added note 6 Modified Page Programming Time Revision 06 (December 8, 2008) Global The data sheet went from a "Preliminary" designation to full production. Revision 07 (May 26, 2009) Table: Power-Up Timing Characteristics Modified table Figure: Power-down and Voltage Drop Added figure Revision 08 (September 8, 2009) AC Characteristics Changed tCS CS# High Time minimum (serial) from 100 to 50 ns Revision 09 (December 8, 2011) Connection Diagrams Added note to WSON package Power-Up / Power-Down Voltage and Timing Table Updated the tPU (max) value AC Characteristics Table Updated the value of tEP Physical Dimensions Updated the package outline drawing for packages SO3 016 and WNF008 Revision 10 (May 16, 2012) Global Added text for recommending FL128S as migration device Revision 11 (September 21, 2012) AC Characteristics Table Changed Output Hold Time (tHO) to 2 ns (min) Revision 12 (January 29, 2013) AC Characteristics 48 Added Capacitance table. S25FL128P S25FL128P_00_12 Janauary 29, 2013 Data She et Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks and Notice The contents of this document are subject to change without notice. This document may contain information on a Spansion product under development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any damages of any kind arising out of the use of the information in this document. Copyright (c) 2007-2013 Spansion Inc. All rights reserved. Spansion(R), the Spansion logo, MirrorBit(R), MirrorBit(R) EclipseTM, ORNANDTM and combinations thereof, are trademarks and registered trademarks of Spansion LLC in the United States and other countries. Other names used are for informational purposes only and may be trademarks of their respective owners. Janauary 29, 2013 S25FL128P_00_12 S25FL128P 49