3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M and MetPak are trademarks of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HM Header
2 mm Type FL, 88 Signal Contacts, 8 Rows, Straight HM Series
Modular/scalable format IEC 61076-4-101•
Press-fit or solder tail version•
101 mated lines per linear inch•
Ships with protective cap, which also serves as an insertion tool•
End-to-end stackable with 8 row 3M• ™ MetPak™ HM and
HSHM Products
See Regulatory Information Appendix (RIA) for chemical •
compliance information
Date Modified: September 24, 2008 TS-2013-B
Sheet 1 of 3
Physical
Insulation:
Material: High Temperature Thermoplastic (LCP)
Flammability: UL94V-0
Contact:
Material: Copper Alloy
Plating: See Ordering Information
Marking: 3M Logo, Part Number, Revision, Date Code
Performance
Mechanical:
Normal Force (Nominal): 0.57 N [ 58 g ] Signal
Engagement Force (Nominal): 0.32 N [ 33 g ] Signal
Separation Force (Nominal): 0.20 N [ 20 g ] Signal
Wipe (Nominal, Shortest Contact) 2.67 mm [ 0.105 in. ] Signal
Durability: 250 cycles with TR40B plating (Lubricated)
Application: This model is not suitable for stand-alone use
Electrical:
Current Rating (Fully Loaded): 1 A at 70° C Signal
Insulation Resistance: 1 x 104 MΩ at 100 VDC
Withstanding Voltage: 750 VRMS
Environmental
Temperature Ratings: -55˚C to +125˚C
Process Rating: Maximum 260°C (per J-STD-020C)
Moisture Sensitivity Level: 1 (per J-STD-020C)
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M and MetPak are trademarks of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HM Header
2 mm Type FL, 88 Signal Contacts, 8 Rows, Straight HM Series
TS-2013-B
Sheet 2 of 3
Ordering Information
HM - H088FL1 - 8CX1 - XXXXX
HM - H110FL2 - 8BX1 - XXXXX
Standard configuration
DIM A = 5.3 mm for rows A through H
DIM B = 4.4 mm
For non-standard configurations contact sales representative
mm
[Inch]
± 0.13
± 0.3 ± 0.3
Tolerance Unless Noted
0. 0.0 0.00
mm
[ ] Dimensions for
Reference only
ROW F
ROW E
ROW D
ROW C
ROW B
ROW A
ROW Z
Pin positions
12345678910 11
DIM A = Pin mating length
DIM B = Pin tail length Shown with protective caps*
* Caps to be removed after press-fit installation process
HM-HXXXXX-8XPX-XXXXX
REV X XXYY
18.00
.709
2.00
.079
2.00
.079
2.00
.079
2.00
.079
20.00
.787
ROW G
ROW H
ROW I
13.40
.528
21.40
.843
15.00
.5915.00
.197
Signal
Contacts
DIM A
DIM B
24.92
.981
1.50
.059
15.15
.596
4.50
.177
Plating Options
(See Plating Chart)
(rows I and Z not loaded)
(rows I and Z loaded 8.3 mm mate length)
Tail Style:
P = Press-t tail
S = Solder tail
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M and MetPak are trademarks of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ HM Header
2 mm Type FL, 88 Signal Contacts, 8 Rows, Straight HM Series
TS-2013-B
Sheet 3 of 3
Recommended PCB hole mounting pattern
Plated thru holes
0.10 A B
ABCDE A
FGH
IZ
DIM D
3.00
2.00
2.00
2.00 +0.05
0
6.00
1
2
3
4
5
6
7
8
9
10
11
18.00
0.10 A B
B
20.00
Ø
Ø
+
+
M
Plating Chart
Plating Suffix Press-Fit Terminations Solder Tail Terminations Plating Composition
TG30 (RIA E2& C2 Apply) (RIA E3 & C2 Apply) “0.76 µm [30 µ””] Min. Au Contact Area
2.54 µm [100 µ””] Min. SnPb Tail Area
1.27 µm [50 µ””] Min. Ni all over “
TR40B (RIA E2& C2 Apply) (RIA E3 & C2 Apply) “0.127 µm [5 µ””] Min. Hard Au over
1.02 µm [40 µ””] Min. Pd/Ni over
0.10 µm [4 µ””] Min. Pd Strike Contact Area
2.54 µm [100µ””] Min SnPb Terminal Area
1.27 µm [50 µ””] Min. Ni all over
(Lubricated Contact Area)
FINISHED HOLE DIA. (D) Cu. THICKNESS SnPb THICKNESS DRILLED HOLE DIA.
0.550 - 0.650 [.0217 - .0256] 0.025 - 0.045 [.0010 - .0018] 0.008 - 0.018 [.0003 - .0007] 0.686 - 0.727 [.0270 - .0286]
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC, as amended by EU Commission Decision 2005/717/EC, as amended by
EU Court of Justice Decision 2008/C 116/04
This product contains decaBDE in the insulating material in excess of the maximum concentration allowed for finished
products subject to EU RoHS that are placed on the EU market after June 30, 2008.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-E
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the
product or part does not contain any of the following substances in excess of the following maximum concentration values in any
homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated
diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217B-E
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217B-E
3
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects 3M is a trademark of 3M Company.
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
