Precision Edge(R) 2.5V, 2.0GHz ANY DIFF. IN-TO-LVDS (R) SY89875U Precision Edge PROGRAMMABLE CLOCK DIVIDER AND 1:2 SY89875U FANOUT BUFFER W/ INTERNAL TERMINATION Micrel, Inc. FEATURES DESCRIPTION Integrated programmable clock divider and 1:2 fanout buffer Guaranteed AC performance over temperature and voltage: * > 2.0GHz fMAX * < 200ps tr/tf * < 15ps within device skew Low jitter design: * < 10psPP total jitter * < 1psRMS cycle-to-cycle jitter Unique input termination and VT Pin for DC-coupled and AC-coupled Inputs; CML, PECL, LVDS and HSTL LVDS compatible outputs TTL/CMOS inputs for select and reset Parallel programming capability Programmable divider ratios of 1, 2, 4, 8 and 16 Low voltage operation 2.5V Output disable function -40C to 85C temperature range Available in 16-pin (3mm x 3mm) MLF(R) package This low-skew, low-jitter device is capable of accepting a high-speed (e.g., 622MHz or higher) CML, LVPECL, LVDS or HSTL clock input signal and dividing down the frequency using a programmable divider to create a lower speed version of the input clock. Available divider ratios are 2, 4, 8 and 16, or straight pass-through. The differential input buffer has a unique internal termination design that allows access to the termination network through a VT pin. This feature allows the device to easily interface to different logic standards. A VREF-AC reference is included for AC-coupled applications. The /RESET input asynchronously resets the divider. In the pass-through function (divide by 1) the /RESET synchronously enables or disables the outputs on the next falling edge of IN (rising edge of /IN). TYPICAL PERFORMANCE APPLICATIONS OC-12 to OC-3 Translator/Divider SONET/SDH line cards Transponders High-end, multiprocessor servers CML/LVPECL/LVDS 622MHz Clock In FUNCTIONAL BLOCK DIAGRAM Divide-by-4 LVDS 155.5MHz Clock Out 622MHz In ! IN ! "#$ "#$ /IN 9 9 Q0 155.5MHz Out % /Q0 Precision Edge is a registered trademark of Micrel, Inc. MicroLeadFrame and MLF are registered trademarks of Amkor Technology, Inc. M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Rev.: D 1 Amendment: /0 Issue Date: August 2007 Precision Edge(R) SY89875U Micrel, Inc. S0 S1 VCC GND PACKAGE/ORDERING INFORMATION 16 15 14 13 Ordering Information(1) VT Q1 3 10 VREF-AC /Q1 4 9 6 7 8 VCC IN 11 /RESET 12 2 S2 1 NC Q0 /Q0 5 Package Operating Type Range Part Number /IN Package Marking Lead Finish 875U Sn-Pb SY89875UMI MLF-16 SY89875UMITR(2) Industrial MLF-16 Industrial 875U Sn-Pb SY89875UMG(3) MLF-16 Industrial 875U with Pb-Free bar line indicator NiPdAu Pb-Free SY89875UMGTR(2, 3) MLF-16 Industrial 875U with Pb-Free bar line indicator NiPdAu Pb-Free Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. 16-Pin MLF(R) (MLF-16) PIN DESCRIPTION Pin Number Pin Name Pin Function 12, 9 IN, /IN 1, 2, 3, 4 Q0, /Q0 Q1, /Q1 16, 15, 5 S0, S1, S2 6 NC 8 /RESET, /DISABLE LVTTL/CMOS Logic Levels: Internal 25ky pull-up resistor. Logic HIGH if left unconnected. Apply LOW to reset the divider (divided by 2, 4, 8 or 16 mode). Also acts as a disable/enable function. The reset and disable function occurs on the next high-to-low clock input transition. Input threshold is VCC/2. 10 VREF-AC Reference Voltage: Equal to VCC-1.4V (approx.). Used for AC-coupled applications only. Decouple the VREF-AC pin with a 0.01F capacitor. See "Input Interface Applications" section. 11 VT 7, 14 VCC 13 GND Exposed Differential Input: Internal 50y termination resistors to VT input. Flexible input accepts any differential input. See "Input Interface Applications" section. Differential Buffered LVDS Outputs: Divided by 1, 2, 4, 8 or 16. See "Truth Table." Unused output pairs must be terminated with 100y across the different pair. Select Pins: See "Truth Table." LVTTL/CMOS logic levels. Internal 25ky pull-up resistor. Logic HIGH if left unconnected (divided by 16 mode.) Input threshold is VCC/2. No Connect. Termination Center-Tap: For CML or LVDS inputs, leave this pin floating. Otherwise, See Figures 4a to 4f, "Input Interface Applications" section. Positive Power Supply: Bypass with 0.1F//0.01F low ESR capacitor. Ground. Exposed pad must be connected to the same potential as the GND pin. TRUTH TABLE /RESET(1) S2 S1 S0 Outputs 1 0 X X Reference Clock (pass through) 1 1 0 0 Reference Clock /2 1 1 0 1 Reference Clock /4 1 1 1 0 Reference Clock /8 1 1 1 1 Reference Clock /16 0(1) X X X Q = LOW, /Q = HIGH Clock Disable Note 1. Reset/Disable function is asserted on the next clock input (IN, /IN) high-to-low transition. M9999-082407 hbwhelp@micrel.com or (408) 955-1690 2 Precision Edge(R) SY89875U Micrel, Inc. Absolute Maximum Ratings(Note 1) Operating Ratings(Note 2) Supply Voltage (VCC) ................................... -0.5V to +4.0V Input Voltage (VIN) ................................... -0.5V to VCC+0.3 ECL Output Current (IOUT) Continuous .......................................................... 50mA Surge .................................................................100mA Input Current IN, /IN (IIN) ......................................... 50mA VT Current (IVT) ...................................................... 100mA VREF-AC Sink/Source Current (IVREF-AC), Note 3 ...... 2mA Lead Temperature (soldering 20 sec.) ...................... 260C Storage Temperature (TS) ........................ -65C to +150C Supply Voltage (VCC) ......................................... +2.5V 5% Ambient Temperature (TA) ......................... -40C to +85C Package Thermal Resistance MLF(R) (JA) Still-Air ............................................................. 60C/W 500lfpm ........................................................... 54C/W MLF(R) (JB), Note 4 Junction-to-Board ............................................ 32C/W Note 1. Note 2. Note 3. Note 4. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. Due to the limited drive capability use for input of the same package only. Junction-to-board resistance assumes exposed pad is soldered (or equivalent) to the device's most negative potential on the pcb. DC ELECTRICAL CHARACTERISTICS(Notes 1, 2) TA= -40C to +85C; Unless otherwise stated. Symbol Parameter VCC Power Supply ICC Power Supply Current RIN Differential Input Resistance (IN-to-/IN) VIH Input High Voltage (IN, /IN) VIL Max Units 2.625 V 70 95 mA 90 100 110 y Note 3 0.1 - VCC+0.3 V Input Low Voltage (IN, /IN) Note 3 -0.3 - VIH-0.1 V VIN Input Voltage Swing Note 4 0.1 - VCC V VDIFF_IN Differential Input Voltage Swing Note 5 0.2 - - V |IIN| Input Current (IN, /IN) Note 3 - - 45 mA VREF-AC Reference Voltage Note 6 Note 1. Note 2. Note 3. Note 4. Note 5. Note 6. Condition Min Typ 2.375 No load, max. VCC VCC-1.525 VCC-1.425 VCC-1.325 V The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. Specification for packaged product only. Due to the internal termination (see Figure 2a) the input current depends on the applied voltages at IN, /IN and VT inputs. Do not apply a combination of voltages that causes the input current to exceed the maximum limit! See "Timing Diagram" for VIN definition. VIN (Max) is specified when VT is floating. See "Typical Operating Characteristics" section for VDIFF definition. Operating using VIN is limited to AC-coupled PECL or CML applications only. Connect directly to VT pin. M9999-082407 hbwhelp@micrel.com or (408) 955-1690 3 Precision Edge(R) SY89875U Micrel, Inc. LVDS DC ELECTRICAL CHARACTERISTICS(Notes 1, 2) VCC = 2.5V 5%; TA = -40C to +85C; Unless otherwise stated. Symbol Parameter Condition Min Typ Max Units VOUT Output Voltage Swing Note 3, 4 250 350 400 mV VOH Output High Voltage Note 3 1.475 V VOL Output Low Voltage Note 3 0.925 VOCM Output Common Mode Voltage Note 4 1.125 1.375 V VOCM Change in Common Mode Voltage -50 50 mV Note 1. Note 2. Note 3. Note 4. V The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. Specification for packaged product only. Measured as per Figure 2a, 100y across Q and /Q outputs. Measured as per Figure 2b. LVTTL/CMOS DC ELECTRICAL CHARACTERISTICS(Notes 1, 2) VCC = 2.5V 5%; TA = -40C to +85C; Unless otherwise stated. Symbol Parameter VIH Input HIGH Voltage VIL Input LOW Voltage IIH Input HIGH Current IIL Input LOW Current Note 1. Note 2. Condition Min Typ Max 2.0 V 0.8 V 20 A -300 A -125 The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. Specification for packaged product only. M9999-082407 hbwhelp@micrel.com or (408) 955-1690 4 Units Precision Edge(R) SY89875U Micrel, Inc. AC ELECTRICAL CHARACTERISTICS(Notes 1, 2) VCC = 2.5V 5%; TA = -40C to +85C; Unless otherwise stated. Symbol Parameter Condition Min Typ fMAX Maximum Input Frequency Output Swing 200mV 2.0 2.5 tPD Differential Propagation Delay IN to Q Input Swing < 400mV 590 690 870 ps Input Swing 400mV 540 690 820 ps 5 15 ps 280 ps tSKEW Max Units GHz Within-Device Skew (diff.) Note 3 Part-to-Part Skew (diff.) Note 3 tRR Reset Recovery Time Note 4 tJITTER Cycle-to-Cycle Jitter Note 5 1 psRMS Total Jitter Note 6 10 psPP 200 ps tr,tf Note 1. Note 2. Note 3. Note 4. Note 5. Note 6. 600 Rise/Fall Time (20% to 80%) 70 ps 120 Measured with 400mV input signal, 50% duty cycle, all outputs loaded with 100y across each output pair, unless otherwise stated. Specification for packaged product only. Skew is measured between outputs under identical transitions. See "Timing Diagram." Cycle-to-cycle jitter definition: the variation in period between adjacent cycles over a random sample of adjacent cycle pairs. Tjitter_cc = Tn-Tn+1, where T is the time between rising edges of the output signal. Total jitter definition: with an ideal clock input of frequency - fMAX, no more than one output edge in 1012 output edges will deviate by more than the specified peak-to-peak jitter value. TIMING DIAGRAM /RESET VCC/2 tRR IN VID /IN VIN Swing tPD /Q VOUT Swing Q M9999-082407 hbwhelp@micrel.com or (408) 955-1690 5 Precision Edge(R) SY89875U Micrel, Inc. TYPICAL OPERATING CHARACTERISTICS VCC = 2.5V, TA = 25C, unless otherwise stated. Output Amplitude vs. Frequency 800 PROPAGATION DELAY (ps) 350 AMPLITUDE (mV) 300 250 200 150 100 50 0 0 750 700 650 600 550 500 0 500 1000 1500 2000 2500 3000 3500 FREQUENCY (MHz) IN to Q Propagation Delay vs. Temperature 60 750 700 650 600 550 500 -60 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) M9999-082407 hbwhelp@micrel.com or (408) 955-1690 200 400 600 800 1000 INPUT SWING (mV) OUTPUT DUTY CYCLE (mV) PROPAGATION DELAY (ps) 800 IN to Q Propagation Delay vs. Input Swing 55 50 45 40 0 6 Output Duty Cycle vs. Frequency 500 1000 1500 2000 2500 3000 FREQUENCY (MHz) Precision Edge(R) SY89875U Micrel, Inc. TYPICAL OPERATING CHARACTERISTICS (Continued) VCC = 2.5V, TA = 25C, unless otherwise stated. 622MHz Output Output Swing (50mV/div.) Output Swing (50mV/div.) 1.25GHz Output TIME (300ps/div.) TIME (140ps/div.) Output Swing (50mV/div.) 2.5GHz Output TIME (80ps/div.) DEFINITION OF SINGLE-ENDED AND DIFFERENTIAL SWINGS VDIFF_IN, VDIFF_OUT 700mV (typical) VIN, VOUT 350mV (typical) Figure 1b. Differential Swing Figure 1a. Single-Ended Swing M9999-082407 hbwhelp@micrel.com or (408) 955-1690 7 Precision Edge(R) SY89875U Micrel, Inc. INPUT INTERFACE APPLICATIONS VCC VCC 1.86k 1.86k 1.86k 25k R S0 S1 S2 /RESET 1.86k R IN 50 VT 50 GND GND /IN Figure 2b. Simplified TTL/CMOS Input Buffer Figure 2a. Simplified Differential Input Buffer LVDS OUTPUTS LVDS (Low Voltage Differential Swing) specifies a small swing of 350mV typical, on a nominal 1.25V common mode above ground. The common mode voltage has tight limits to permit large variations in ground between an LVDS driver and receiver. Also, change in common mode voltage, as a function of data input, is also kept tight, to keep EMI low. 50 vOD vOH, vOL 100 vOH, vOL 50 GND GND Figure 3b. LVDS Common Mode Measurement Figure 3a. LVDS Differential Measurement M9999-082407 hbwhelp@micrel.com or (408) 955-1690 vOCM, vOCM 8 Precision Edge(R) SY89875U Micrel, Inc. INPUT INTERFACE APPLICATIONS VCC VCC VCC VCC VCC VCC IN IN IN CML CML PECL /IN /IN /IN SY89875U GND GND NC VT NC VREF_AC VCC VCC VCC VCC 509 509 VCC GND 0.01F IN VT VREF_AC Figure 4d. AC-Coupled CML Input Interface 5;&'&%#7 GND NC VT NC VREF_AC Figure 4e. LVDS Input Interface VREF_AC VCC Figure 4c. DC-Coupled PECL Input Interface VCC VCC IN /IN /IN 5;&'&%#7 VT NC HSTL LVDS /IN VCC -2V 39 Figure 4b. AC-Coupled CML Input Interface VCC GND 0.01F VREF_AC IN PECL GND VT 0.01F Figure 4a. DC-Coupled CML Input Interface SY89875U 5;&'&%#7 GND 5;&'&%#7 VT NC VREF_AC GND Figure 4f. HSTL Input Interface RELATED PRODUCT AND SUPPORT DOCUMENTATION Part Number Function Data Sheet Link SY89872U 2.5V, 2.5GHz Any Diff. In-to-LVDS Programmable Clock Divider/Fanout Buffer w/ Internal Termination http://www.micrel.com/product-info/products/sy89872u.shtml MLF(R) Application Note http://www.amkor.com/products/notes_papers/mlf_appnote_0902.pdf New Products and Applications http://www.micrel.com/product-info/products/solutions.shtml HBW Solutions M9999-082407 hbwhelp@micrel.com or (408) 955-1690 9 Precision Edge(R) SY89875U Micrel, Inc. 16-PIN MicroLeadFrame(R) (MLF-16) Package EP- Exposed Pad Die CompSide Island Heat Dissipation Heat Dissipation VEE Heavy Copper Plane VEE Heavy Copper Plane PCB Thermal Consideration for 16-Pin MLF(R) Package (Always solder, or equivalent, the exposed pad to the PCB) Package Notes: Note 1. Note 2. Package meets Level 2 moisture sensitivity classification, and are shipped in dry-pack form. Exposed pads must be soldered to a ground for proper thermal management. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. M9999-082407 hbwhelp@micrel.com or (408) 955-1690 10