6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL-0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL-2630, HCPL-2631, HCPL-4661 High CMR, High Speed TTL Compatible Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The 6N137, HCPL-26XX/06XX/4661, HCNW137/26X1 are optically coupled gates that combine a GaAsP light emitting diode and an integrated high gain photo detector. An enable input allows the detector to be strobed. The output of the detector IC is an open collector Schottkyclamped transistor. The internal shield provides a guaranteed common mode transient immunity specification up to 15,000 V/s at Vcm=1000V. 15 kV/s minimum Common Mode Rejection (CMR) at VCM = 1KV for HCNW2611, HCPL-2611, HCPL-4661, HCPL-0611, HCPL-0661 High speed: 10 MBd typical LSTTL/TTL compatible Low input current capability: 5 mA Guaranteed ac and dc performance over temperature: -40C to +85C Available in 8-Pin DIP, SOIC-8, widebody packages Strobable output (single channel products only) Safety approval UL recognized - 3750 V rms for 1 minute and 5000 Vrms* for 1 minute per UL1577 CSA approved IEC/EN/DIN EN 60747-5-2 approved with VIORM = 560 V peak for 06xx Option 060 VIORM = 630 V peak for 6N137/26xx Option 060 VIORM = 1414 V peak for HCNW137/26X1 MIL-PRF-38534 hermetic version available (HCPL-56XX/66XX) This unique design provides maximum ac and dc circuit isolation while achieving TTL compatibility. The optocoupler ac and dc operational parameters are guaranteed from 40C to +85C allowing troublefree system performance. Functional Diagram 6N137, HCPL-2601/2611 HCPL-0600/0601/0611 HCPL-2630/2631/4661 HCPL-0630/0631/0661 ANODE 1 1 8 VCC VE CATHODE 1 2 7 VO1 6 VO CATHODE 2 3 6 VO2 5 GND ANODE 2 4 5 GND NC 1 8 VCC ANODE 2 7 CATHODE 3 NC 4 SHIELD TRUTH TABLE (POSITIVE LOGIC) LED ON OFF ON OFF ON OFF ENABLE H H L L NC NC OUTPUT L H H H L H SHIELD TRUTH TABLE (POSITIVE LOGIC) LED ON OFF OUTPUT L H A 0.1 F bypass capacitor must be connected between pins 5 and 8. Applications Isolated line receiver Computer-peripheral interfaces Microprocessor system interfaces Digital isolation for A/D, D/A conversion Switching power supply Instrument input/output isolation Ground loop elimination Pulse transformer replacement Power transistor isolation in motor drives Isolation of high speed logic systems *5000 V rms/1 Minute rating is for HCNW137/26X1 and Option 020 (6N137, HCPL-2601/11/30/31, HCPL-4661) products only. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. The 6N137, HCPL-26XX, HCPL-06XX, HCPL-4661, HCNW137, and HCNW26X1 are suitable for high speed logic interfacing, input/output buffering, as line receivers in environments that conventional line receivers cannot tolerate and are recommended for use in extremely high ground or induced noise environments. Selection Guide Minimum CMR 8-Pin DIP (300 Mil) dV/dt (V/s) VCM (V) Input OnCurrent (mA) 1000 10 5 YES 5,000 1,000 5 YES Output Enable Single Channel Package 6N137 Dual Channel Package 1,000 YES HCPL-2630 HCPL-2601 NO 15,000 1,000 YES 50 YES HCPL-2602 YES HCPL-2612[1] 1,000 50 YES HCPL-261A[1] 1,000 50 12.5 HCNW2611 HCPL-0661 HCPL-061A[1] HCPL-261N[1] HCPL-063A[1] HCPL-061N[1] HCPL-263N[1] [3] Notes: 1. Technical data are on separate Avago publications. 2. 15 kV/s with VCM = 1 kV can be achieved using Avago application circuit. 3. Enable is available for single channel products only, except for HCPL-193X devices. 2 HCNW2601 HCPL-0611 HCPL-263A[1] NO NO Single and Dual Channel Packages HCPL-0631 HCPL-4661 300 YES Single Channel Package [1] 1,000 1,000 Hermetic HCNW137 HCPL-0601 HCPL-2611 3, 500 1,000[2] Dual Channel Package Widebody (400 Mil) HCPL-0630 HCPL-2631 NO 3 Single Channel Package HCPL-0600 NO 10,000 Small-Outline SO-8 HCPL-063N[1] HCPL-193X[1] HCPL-56XX[1] HCPL-66XX[1] Ordering Information HCPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNWxxxx is UL Rcognized with 5000 Vrms for 1 minute per UL1577. Option Part Number 6N137 HCPL-2601 HCPL-2611 HCPL-2630 HCPL-2631 HCPL-4661 3 RoHS Compliant Non RoHS Compliant -000E No option -300E #300 X X -500E #500 X X -020E #020 -320E #320 -520E #520 -060E #060 -560E -560 -000E No option -300E #300 X X -500E #500 X X -020E #020 -320E #320 -520E #520 -060E #060 -360E - -000E No option -300E #300 X X -500E #500 X X -020E #020 Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute Rating IEC/EN/DIN EN 60747-5-2 Quantity 50 per tube 300mil DIP-8 X X X X X X 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel X X 50 per tube X 1000 per reel 50 per tube 300mil DIP-8 X X X X X 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel X X 50 per tube X 50 per tube 50 per tube 300mil DIP-8 -320E #320 X X -520E #520 X X -060E #060 -360E #360 X X -560E #560 X X -000E No option -300E #300 -500E #500 -020E #020 -320E #320 X X -520E -520 X X -000E No option -300E #300 -500E #500 -020E #020 -320E -520E 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel X X 50 per tube X 50 per tube X 1000 per reel 50 per tube 300mil DIP-8 X X X X 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel 50 per tube X X X X #320 X X #520 X X 300mil DIP-8 50 per tube X X 1000 per reel X 50 per tube X 50 per tube X 1000 per reel Option Part Number HCPL-0600 HCPL-0601 HCPL-0611 HCPL-0630 HCPL-0631 HCPL-0661 HCNW137 HCNW2601 HCNW2611 RoHS Compliant Non RoHS Compliant -000E No option -500E #500 -060E #060 -560E #560 -000E No option No option #500 Tape & Reel UL 5000 Vrms/ 1 Minute Rating IEC/EN/DIN EN 60747-5-2 X X 1500 per reel X X X 100 per tube X 1500 per reel X 100 per tube X 400 mil DIP-8 Quantity 100 per tube X SO-8 -000E -500E Gull Wing X #500 #300 Package SO-8 -500E -300E Surface Mount X X X X X 1500 per reel X X X 42 per tube X X 42 per tube X X 750 per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Combination of Option 020 and Option 060 is not available. Example 1: HCPL-2611-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packag ing with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-2630 to order product of 300mil DIP package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Notes: The notation `#XXX' is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use `-XXXE`. Schematic IF 6N137, HCPL-2601/2611 HCPL-0600/0601/0611 HCNW137, HCNW2601/2611 HCPL-2630/2631/4661 HCPL-0630/0631/0661 ICC 1 ICC 8 2+ IO 6 VCC VO 8 IF1 IO1 + 7 VCC VO1 VF1 - 2 VF SHIELD - 3 SHIELD IE 5 7 VE USE OF A 0.1 F BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5). GND 3 IF2 IO2 - 6 VF2 + 4 SHIELD 4 VO2 5 GND Package Outline Drawings 8-pin DIP Package** (6N137, HCPL-2601/11/30/31, HCPL-4661) 7.62 0.25 (0.300 0.010) 9.65 0.25 (0.380 0.010) 8 TYPE NUMBER 7 6 5 6.35 0.25 (0.250 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW RU 1 2 3 4 UL RECOGNITION 1.78 (0.070) MAX. 1.19 (0.047) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 5 TYP. 3.56 0.13 (0.140 0.005) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). 0.65 (0.025) MAX. 1.080 0.320 (0.043 0.013) *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. 2.54 0.25 (0.100 0.010) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. **JEDEC Registered Data (for 6N137 only). 8-pin DIP Package with Gull Wing Surface Mount Option 300 (6N137, HCPL-2601/11/30/31, HCPL-4661) LAND PATTERN RECOMMENDATION 9.65 0.25 (0.380 0.010) 8 7 6 1.016 (0.040) 5 6.350 0.25 (0.250 0.010) 1 2 3 10.9 (0.430) 4 1.27 (0.050) 1.19 (0.047) MAX. 1.780 (0.070) MAX. 9.65 0.25 (0.380 0.010) 7.62 0.25 (0.300 0.010) 3.56 0.13 (0.140 0.005) 1.080 0.320 (0.043 0.013) 0.635 0.25 (0.025 0.010) 0.635 0.130 2.54 (0.025 0.005) (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 5 2.0 (0.080) + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 12 NOM. Small-Outline SO-8 Package (HCPL-0600/01/11/30/31/61) LAND PATTERN RECOMMENDATION 8 7 6 5 5.994 0.203 (0.236 0.008) XXX YWW 3.937 0.127 (0.155 0.005) 7.49 (0.295) TYPE NUMBER (LAST 3 DIGITS) DATE CODE PIN ONE 1 2 3 4 0.406 0.076 (0.016 0.003) 1.9 (0.075) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 0.127 (0.200 0.005) 3.175 0.127 (0.125 0.005) 7 45 X 0.432 (0.017) 0 ~ 7 0.228 0.025 (0.009 0.001) 1.524 (0.060) 0.203 0.102 (0.008 0.004) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 0.254 (0.205 0.010) 0.305 MIN. (0.012) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. 8-Pin Widebody DIP Package (HCNW137, HCNW2601/11) 11.00 MAX. (0.433) 11.23 0.15 (0.442 0.006) 8 7 6 9.00 0.15 (0.354 0.006) 5 TYPE NUMBER A HCNWXXXX DATE CODE YYWW 1 2 3 4 10.16 (0.400) TYP. 1.55 (0.061) MAX. 7 TYP. + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) 5.10 MAX. (0.201) 3.10 (0.122) 3.90 (0.154) 0.51 (0.021) MIN. 2.54 (0.100) TYP. 1.80 0.15 (0.071 0.006) 0.40 (0.016) 0.56 (0.022) DIMENSIONS IN MILLIMETERS (INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 6 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW137, HCNW2601/11) 11.23 0.15 (0.442 0.006) 8 7 6 LAND PATTERN RECOMMENDATION 5 9.00 0.15 (0.354 0.006) 1 2 3 13.56 (0.534) 4 2.29 (0.09) 1.3 (0.051) 12.30 0.30 (0.484 0.012) 1.55 (0.061) MAX. 11.00 MAX. (0.433) 4.00 MAX. (0.158) 1.80 0.15 (0.071 0.006) 0.75 0.25 (0.030 0.010) 2.54 (0.100) BSC 1.00 0.15 (0.039 0.006) + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) DIMENSIONS IN MILLIMETERS (INCHES). 7 NOM. LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. Solder Reflow Temperature Profile 300 PREHEATING RATE 3 C + 1 C/-0.5 C/SEC. REFLOW HEATING RATE 2.5 C 0.5 C/SEC. 200 PEAK TEMP. 245 C PEAK TEMP. 240 C TEMPERATURE (C) 2.5 C 0.5 C/SEC. 30 SEC. 160 C 150 C 140 C SOLDERING TIME 200 C 30 SEC. 3 C + 1 C/-0.5 C 100 PREHEATING TIME 150 C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 TIME (SECONDS) NOTE: NON-HALIDE FLUX SHOULD BE USED. 7 PEAK TEMP. 230 C 200 250 Recommended Pb-free IR Profile tp Tp TEMPERATURE TL Tsmax * 260 +0/-5 C TIME WITHIN 5 C of ACTUAL PEAK TEMPERATURE 15 SEC. 217 C 150 - 200 C RAMP-UP 3 C/SEC. MAX. NOTES: THE TIME FROM 25 C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 C, Tsmin = 150 C RAMP-DOWN 6 C/SEC. MAX. Tsmin ts PREHEAT 60 to 180 SEC. 25 tL NOTE: NON-HALIDE FLUX SHOULD BE USED. 60 to 150 SEC. * RECOMMENDED PEAK TEMPERATURE FOR WIDEBODY 400mils PACKAGE IS 245 C t 25 C to PEAK TIME Regulatory Information The 6N137, HCPL-26XX/06XX/46XX, and HCNW137/26XX have been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 Approved under IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01 (Option 060 and HCNW only) Insulation and Safety Related Specifications Parameter Symbol 8-pin DIP (300 Mil) Value Minimum External Air Gap (External Clearance) L(101) 7.1 4.9 9.6 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 7.4 4.8 10.0 mm Measured from input terminals to output terminals, shortest distance path along body. Minimum Internal Plastic Gap (Internal Clearance) 0.08 0.08 1.0 mm Through insulation distance, conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal Tracking (Internal Creepage) NA NA 4.0 mm Measured from input terminals to output terminals, along internal cavity. 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1 IIIa IIIa IIIa Tracking Resistance (Comparative Tracking Index) Isolation Group CTI SO-8 Value Widebody (400 Mil) Value Units Conditions Material Group (DIN VDE 0110, 1/89, Table 1) Option 300 - surface mount classification is Class A in accordance with CECC 00802. 8 IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-06xx Option 060 Only) Description Symbol Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage 150 V rms Characteristic I-IV for rated mains voltage 300 V rms I-III for rated mains voltage 600 V rms I-III Climatic Classification 55/85/21 Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Units 2 VIORM 567 V peak Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC VPR 1063 V peak Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and Sample Test, tm = 60 sec, Partial Discharge < 5 pC VPR 851 V peak VIOTM 6000 V peak TS IS,INPUT PS,OUTPUT 150 150 600 C mA mW RS 109 Highest Allowable Overvoltage (Transient Overvoltage, tini = 10 sec) Safety Limiting Values (Maximum values allowed in the event of a failure) Case Temperature Input Current** Output Power** Insulation Resistance at TS, VIO = 500 V *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. 9 IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-26xx; 46xx; 6N13x Option 060 Only) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage 300 V rms for rated mains voltage 450 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and sample test, tm = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 16, Thermal Derating curve.) Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500 V Symbol Characteristic Units VIORM I-IV I-III 55/85/21 2 630 V peak VPR 1181 V peak VPR 945 V peak VIOTM 6000 V peak TS IS,INPUT PS,OUTPUT RS 175 230 600 109 C mA mW *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW137/2601/2611 Only) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage 600 V rms for rated mains voltage 1000 V rms Climatic Classification (DIN IEC 68 part 1) Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.5 = VPR, Type and sample test, tm = 60 sec, Partial Discharge < 5 pC Highest Allowable Overvoltage* (Transient Overvoltage, tini = 10 sec) Safety Limiting Values (Maximum values allowed in the event of a failure, also see Figure 16, Thermal Derating curve.) Case Temperature Input Current Output Power Insulation Resistance at TS, VIO = 500 V Symbol Characteristic Units VIORM I-IV I-III 55/100/21 2 1414 V peak VPR 2651 V peak VPR 2121 V peak VIOTM 8000 V peak TS IS,INPUT PS,OUTPUT RS 150 400 700 109 C mA mW *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. 10 Absolute Maximum Ratings* (No Derating Required up to 85C) Parameter Symbol Package** Min. Max. Units Storage Temperature TS -55 125 C Operating Temperature TA -40 85 C Average Forward Input Current IF Single 8-Pin DIP Single SO-8 Widebody 20 mA Dual 8-Pin DIP Dual SO-8 15 8-Pin DIP, SO-8 5 Widebody 3 Widebody 40 mW 7 V VCC + 0.5 V Reverse Input Voltage VR Note 2 1, 3 V 1 Input Power Dissipation PI Supply Voltage (1 Minute Maximum) VCC Enable Input Voltage (Not to Exceed VCC by more than 500 mV) VE Enable Input Current IE 5 mA Output Collector Current IO 50 mA 1 Output Collector Voltage VO 7 V 1 Output Collector Power Dissipation PO Single 8-Pin DIP Single SO-8 Widebody 85 mW Dual 8-Pin DIP Dual SO-8 60 Lead Solder Temperature (Through Hole Parts Only) Solder Reflow Temperature Profile (Surface Mount Parts Only) TLS Single 8-Pin DIP Single SO-8 Widebody 1, 4 8-Pin DIP 260C for 10 sec., 1.6 mm below seating plane Widebody 260C for 10 sec., up to seating plane SO-8 and Option 300 See Package Outline Drawings section *JEDEC Registered Data (for 6N137 only). **Ratings apply to all devices except otherwise noted in the Package column. 0C to 70C on JEDEC Registration. Recommended Operating Conditions Parameter Input Current, Low Level [1] Input Current, High Level Power Supply Voltage Symbol Min. Max. Units IFL* 0 250 A IFH** 5 15 mA VCC 4.5 5.5 V Low Level Enable Voltage VEL 0 0.8 V High Level Enable Voltage VEH 2.0 VCC V Operating Temperature TA -40 85 C 5 TTL Loads 4k [1] Fan Out (at RL = 1 k) N Output Pull-up Resistor RL 330 *The off condition can also be guaranteed by ensuring that VFL 0.8 volts. **The initial switching threshold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be used for best performance and to permit at least a 20% LED degradation guardband. For single channel products only. 11 Electrical Specifications Over recommended temperature (TA = -40C to +85C) unless otherwise specified. All Typicals at VCC = 5 V, TA = 25C. All enable test conditions apply to single channel products only. See note 5. Parameter Sym. Package High Level Output Current IOH* Input Threshold Current ITH Low Level Output Voltage High Level Supply Current VOL* ICCH Min. Typ. Max. Units Test Conditions Fig. Note All 5.5 100 A VCC = 5.5 V, VE = 2.0 V, VO = 5.5 V, IF = 250 A 1 1, 6, 19 Single Channel Widebody Dual Channel 2.0 5.0 mA VCC = 5.5 V, VE = 2.0 V, VO = 0.6 V, IOL (Sinking) = 13 mA 2, 3 19 0.6 V VCC = 5.5 V, VE = 2.0 V, IF = 5 mA, IOL (Sinking) = 13 mA 2, 3, 4, 5 1, 19 mA VE = 0.5 V VE = VCC Both Channels VCC = 5.5 V IF = 0 mA 7 mA VE = 0.5 V VE = VCC Both Channels VCC = 5.5 V IF = 10 mA 8 2.5 8-Pin DIP SO-8 Widebody 0.35 Single Channel 7.0 6.5 10 10.0* 13.0* Dual Channel 9.0 8.5 13 Single Channel -0.7 -1.6 mA VCC = 5.5 V, VE = 2.0 V -0.9 -1.6 mA VCC = 5.5 V, VE = 0.5 V 0.4 Dual Channel Low Level Supply Current ICCL High Level Enable Current IEH Low Level Enable Current IEL* High Level Enable Voltage VEH Low Level Enable Voltage VEL Input Forward Voltage VF Input Reverse Breakdown Voltage BVR* Input Diode Temperature Coefficient DVF / TA Input Capacitance CIN Single Channel 15 21 2.0 8-Pin DIP SO-8 Widebody 1.4 1.3 1.25 1.2 8-Pin DIP SO-8 Widebody 5 V 1.5 1.64 0.8 V 1.75* 1.80 1.85 2.05 V 19 TA = 25C IF = 10 mA 6, 7 1 TA = 25C V 3 IR = 10 A 1 IR = 100 A, TA = 25C 8-Pin DIP SO-8 Widebody -1.6 8-Pin DIP SO-8 Widebody 60 mV/C IF = 10 mA 7 1 -1.9 pF f = 1 MHz, VF = 0 V 70 *JEDEC registered data for the 6N137. The JEDEC Registration specifies 0C to +70C. HP specifies -40C to +85C. 12 9 1 Switching Specifications (AC) Over Recommended Temperature (TA = -40C to +85C), VCC = 5 V, IF = 7.5 mA unless otherwise specified. All Typicals at TA = 25C, VCC = 5 V. Parameter Sym. Propagation Delay Time to High Output Level Propagation Delay Time to Low Output Level Pulse Width Distortion Package** Min. Typ. Max. Units tPLH 20 48 75* 100 ns TA = 25C tPHL 25 50 75* 100 ns TA = 25C 3.5 35 ns |tPHL - tPLH| Propagation Delay Skew 8-Pin DIP SO-8 Widebody Test Conditions RL = 350 CL = 15 pF 40 Note 8, 9, 10 1, 10, 19 1, 11, 19 8, 9, 10, 11 40 tPSK Fig. ns 13, 19 12, 13, 19 Output Rise Time (10-90%) tr 24 ns 12 1, 19 Output Fall Time (90-10%) tf 10 ns 12 1, 19 13, 14 14 Propagation Delay Time of Enable from VEH to VEL tELH Single Channel 30 ns Propagation Delay Time of Enable from VEL to VEH tEHL Single Channel 20 ns RL = 350 , CL = 15 pF, VEL = 0 V, VEH = 3 V 15 *JEDEC registered data for the 6N137. **Ratings apply to all devices except otherwise noted in the Package column. Parameter Sym. Logic High Common Mode Transient Immunity |CMH| Logic Low Common Mode Transient Immunity 13 |CML| Device 6N137 HCPL-2630 HCPL-0600/0630 HCNW137 HCPL-2601/2631 HCPL-0601/0631 HCNW2601 HCPL-2611/4661 HCPL-0611/0661 HCNW2611 6N137 HCPL-2630 HCPL-0600/0630 HCNW137 HCPL-2601/2631 HCPL-0601/0631 HCNW2601 HCPL-2611/4661 HCPL-0611/0661 HCNW2611 Min. Typ. Units 1,000 5,000 10,000 10,000 V/s Test Conditions |VCM| = 10 V |VCM| = 1 kV 10,000 15,000 |VCM| = 1 kV 15,000 25,000 |VCM| = 1 kV 1,000 5,000 10,000 10,000 V/s |VCM| = 10 V |VCM| = 1 kV 10,000 15,000 |VCM| = 1 kV 15,000 25,000 |VCM| = 1 kV Fig. Note VCC = 5 V, IF = 0 mA, VO(MIN) = 2 V, RL = 350 , TA = 25C 15 1, 16, 18, 19 VCC = 5 V, IF = 7.5 mA, VO(MAX) = 0.8 V, RL = 350 , TA = 25C 15 1, 17, 18, 19 Package Characteristics All Typicals at TA = 25C. Parameter Sym. Package Input-Output Insulation II-O* Single 8-Pin DIP Single SO-8 Input-Output Momentary Withstand Voltage** VISO 8-Pin DIP, SO-8 Widebody OPT 020 Input-Output Resistance RI-O 8-Pin DIP, SO-8 Widebody Input-Output Capacitance CI-O Min. Typ. Max. Units 1 A 3750 5000 5000 12 10 1011 V rms 0.6 0.5 RH 50%, t = 1 min, TA = 25C 20, 21 20, 22 VI-O = 500 V dc pF f = 1 MHz, TA = 25C RH 45%, t = 5 s, VI-I = 500 V 0.6 II-I Dual Channel 0.005 A Resistance (Input-Input) RI-I Dual Channel 1011 Capacitance (Input-Input) CI-I Dual 8-Pin DIP Dual SO-8 0.03 0.25 pF Note 20, 21 TA = 25C TA = 100C Input-Input Insulation Leakage Current Fig. 45% RH, t = 5 s, VI-O = 3 kV dc, TA = 25C 1012 1013 8-Pin DIP, SO-8 Widebody Test Conditions 1, 20, 23 1, 20, 23 24 24 f = 1 MHz 24 *JEDEC registered data for the 6N137. The JEDEC Registration specifies 0C to 70C. Avago specifies -40C to 85C. **The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage." For 6N137, HCPL-2601/2611/2630/2631/4661 only. Notes: 1. Each channel. 2. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 20 mA. 3. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 15 mA. 4. Derate linearly above 80C free-air temperature at a rate of 2.7 mW/C for the SOIC-8 package. 5. Bypassing of the power supply line is required, with a 0.1 F ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 17. Total lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm. 6. The JEDEC registration for the 6N137 specifies a maximum IOH of 250 A. Avago guarantees a maximum IOH of 100 A. 7. The JEDEC registration for the 6N137 specifies a maximum ICCH of 15 mA. Avago guarantees a maximum ICCH of 10 mA. 8. The JEDEC registration for the 6N137 specifies a maximum ICCL of 18 mA. Avago guarantees a maximum ICCL of 13 mA. 9. The JEDEC registration for the 6N137 specifies a maximum IEL of -2.0 mA. Avago guarantees a maximum IEL of -1.6 mA. 10. The tPLH propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge of the output pulse. 11. The tPHL propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge of the output pulse. 12. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature and specified test conditions. 13. See application section titled "Propagation Delay, Pulse-Width Distortion and Propagation Delay Skew" for more information. 14. The tELH enable propagation delay is measured from the 1.5 V point on the falling edge of the enable input pulse to the 1.5 V point on the rising edge of the output pulse. 15. The tEHL enable propagation delay is measured from the 1.5 V point on the rising edge of the enable input pulse to the 1.5 V point on the falling edge of the output pulse. 16. CMH is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (i.e., VO > 2.0 V). 17. CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (i.e., VO < 0.8 V). 18. For sinusoidal voltages, (|dVCM | / dt)max = fCMVCM(p-p). 19. No external pull up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single channel products only. 20. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together. 21. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage 4500 V rms for one second (leakage detection current limit, II-O 5 A). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 607475-2 Insulation Characteristics Table, if applicable. 22. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 6000 V rms for one second (leakage detection current limit, II-O 5 A). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 607475-2 Insulation Characteristics Table, if applicable. 23. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together. For dual channel products only. 24. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual channel products only 14 10 * FOR SINGLE CHANNEL PRODUCTS ONLY 5 0 -60 -40 -20 0 20 40 60 4 RL = 350 3 RL = 1 K 2 RL = 4 K 1 0 80 100 TA - TEMPERATURE - C VCC = 5.0 V VO = 0.6 V 4 RL = 350 RL = 1 K 2 1 RL = 4 K 0 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE - C Figure 3. Typical input threshold current vs. temperature. 15 1 2 3 4 5 6 4 RL = 350 3 RL = 1 K 2 RL = 4 K 1 0 Figure 2. Typical output voltage vs. forward input current. ITH - INPUT THRESHOLD CURRENT - mA ITH - INPUT THRESHOLD CURRENT - mA 8-PIN DIP, SO-8 3 0 WIDEBODY 6 5 VCC = 5.0 V VO = 0.6 V 4 3 RL = 1 K RL = 350 2 1 RL = 4 K 0 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE - C VCC = 5 V TA = 25 C 5 IF - FORWARD INPUT CURRENT - mA Figure 1. Typical high level output current vs. temperature. 5 VCC = 5 V TA = 25 C 5 WIDEBODY 6 VO - OUTPUT VOLTAGE - V VCC = 5.5 V VO = 5.5 V VE = 2.0 V* IF = 250 A 6 8-PIN DIP, SO-8 6 VO - OUTPUT VOLTAGE - V IOH - HIGH LEVEL OUTPUT CURRENT - A 15 0 1 2 3 4 5 6 IF - FORWARD INPUT CURRENT - mA * FOR SINGLE CHANNEL PRODUCTS ONLY 0.6 0.5 IO = 16 mA IO = 12.8 mA 0.4 0.3 0.2 IO = 9.6 mA IO = 6.4 mA 0.1 0 -60 -40 -20 0 20 40 60 80 100 WIDEBODY 0.8 VCC = 5.5 V VE = 2.0 V IF = 5.0 mA 0.7 0.6 0.5 IO = 16 mA IO = 12.8 mA 0.4 0.3 IO = 9.6 mA IO = 6.4 mA 0.2 0.1 0 -60 -40 -20 TA - TEMPERATURE - C 0 20 40 60 80 100 8-PIN DIP, SO-8 IF - FORWARD CURRENT - mA IF - FORWARD CURRENT - mA 10 IF + VF - 1.0 0.1 0.01 0.001 1.1 1.2 1.3 1.4 WIDEBODY 1.5 1.6 TA = 25 oC 100 10 IF + VF - 1.0 0.1 0.01 0.001 1.2 1.3 1.4 1.5 1.6 1.7 VF - FORWARD VOLTAGE - V VF - FORWARD VOLTAGE - V 8-PIN DIP, SO-8 dVF/dT - FORWARD VOLTAGE TEMPERATURE COEFFICIENT - mV/C dVF/dT - FORWARD VOLTAGE TEMPERATURE COEFFICIENT - mV/C Figure 6. Typical input diode forward characteristic. -2.4 -2.2 -2.0 -1.8 -1.6 -1.4 -1.2 0.1 1 10 100 IF - PULSE INPUT CURRENT - mA WIDEBODY -2.3 -2.2 -2.1 -2.0 -1.9 -1.8 0.1 1 10 100 IF - PULSE INPUT CURRENT - mA Figure 7. Typical temperature coefficient of forward voltage vs. input current. 16 VCC = 5.0 V VE = 2.0 V* VOL = 0.6 V * FOR SINGLE CHANNEL PRODUCTS ONLY 60 IF = 10-15 mA 50 IF = 5.0 mA 40 20 -60 -40 -20 0 20 40 60 80 100 Figure 5. Typical low level output current vs. temperature. 1000 TA = 25 C 100 70 TA - TEMPERATURE - C TA - TEMPERATURE - C Figure 4. Typical low level output voltage vs. temperature. 1000 IOL - LOW LEVEL OUTPUT CURRENT - mA 0.7 VCC = 5.5 V VE = 2.0 V* IF = 5.0 mA VOL - LOW LEVEL OUTPUT VOLTAGE - V VOL - LOW LEVEL OUTPUT VOLTAGE - V 8-PIN DIP, SO-8 0.8 PULSE GEN. Z O = 50 t f = t r = 5 ns SINGLE CHANNEL PULSE GEN. ZO = 50 t f = t r = 5 ns IF INPUT MONITORING NODE 1 VCC 8 2 7 3 6 4 5 0.1F BYPASS GND VCC 8 2 7 3 6 RL INPUT MONITORING NODE OUTPUT VO MONITORING NODE 1 RM GND IF = 7.50 mA INPUT IF IF = 3.75 mA t PHL t PLH OUTPUT VO 1.5 V Figure 8. Test circuit for tPHL and tPLH. 80 tPLH , RL = 4 K tPHL , RL = 350 1 K 60 4 K tPLH , RL = 1 K 40 20 tPLH , RL = 350 0 -60 -40 -20 20 0 40 60 tP - PROPAGATION DELAY - ns tP - PROPAGATION DELAY - ns 105 VCC = 5.0 V IF = 7.5 mA 45 30 VCC = 5.0 V IF = 7.5 mA 20 RL = 350 0 RL = 1 k 40 60 80 100 TA - TEMPERATURE - oC Figure 11. Typical pulse width distortion vs. temperature. 17 tr, tf - RISE, FALL TIME - ns PWD - PULSE WIDTH DISTORTION - ns RL = 4 k 20 tPHL , RL = 350 1 K 4 K 5 9 7 11 13 15 Figure 10. Typical propagation delay vs. pulse input current. 40 0 tPLH , RL = 1 K IF - PULSE INPUT CURRENT - mA Figure 9. Typical propagation delay vs. temperature. -10 -60 -40 -20 tPLH , RL = 350 60 TA - TEMPERATURE - C 10 tPLH , RL = 4 K 75 30 80 100 VCC = 5.0 V TA = 25C 90 VCC = 5.0 V IF = 7.5 mA tRISE tFALL RL = 4 k 300 290 60 RL = 1 k 40 RL = 350 20 0 -60 -40 -20 0.1F BYPASS C L* 4 *CL IS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE. 100 +5 V IF RL *CL RM DUAL CHANNEL +5 V RL = 350 , 1 k, 4 k 0 20 40 60 80 100 TA - TEMPERATURE - C Figure 12. Typical rise and fall time vs. temperature. 5 OUTPUT VO MONITORING NODE PULSE GEN. Z O = 50 t f = t r = 5 ns INPUT VE MONITORING NODE +5 V 1 7.5 mA IF 3.0 V VCC 8 2 0.1 F BYPASS 7 3 6 4 5 RL 1.5 V t EHL OUTPUT VO MONITORING NODE *C L GND INPUT VE t ELH OUTPUT VO 1.5 V *C L IS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE. tE - ENABLE PROPAGATION DELAY - ns Figure 13. Test circuit for tEHL and tELH. 120 VCC = 5.0 V VEH = 3.0 V VEL = 0 V 90 IF = 7.5 mA tELH, RL = 4 k 60 tELH, RL = 1 k 30 tELH, RL = 350 tEHL, RL = 350 , 1 k, 4 k 0 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE - C Figure 14. Typical enable propagation delay vs. temperature. IF SINGLE CHANNEL DUAL CHANNEL B IF 1 VCC 8 B A VFF 2 7 3 6 4 GND +5 V 0.1 F BYPASS 1 A RL 2 7 3 6 VFF OUTPUT VO MONITORING NODE 5 4 VCM GND VCM + - PULSE GENERATOR Z O = 50 VCM (PEAK) VCM VO VO 0V 5V +5 V RL + - PULSE GENERATOR Z O = 50 SWITCH AT A: IF = 0 mA CMH VO (MIN.) SWITCH AT B: IF = 7.5 mA VO (MAX.) 0.5 V Figure 15. Test circuit for common mode transient immunity and typical waveforms. 18 VCC 8 CML 5 0.1 F BYPASS OUTPUT VO MONITORING NODE PS (mW) 700 IS (mA) 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 200 TS - CASE TEMPERATURE - C OUTPUT POWER - PS, INPUT CURRENT - IS OUTPUT POWER - PS, INPUT CURRENT - IS HCPL-2611 OPTION 060 800 HCNWXXXX PS (mW) IS (mA) 800 700 600 500 400 300 200 100 0 0 25 50 75 100 125 150 175 TS - CASE TEMPERATURE - C Figure 16. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-2. GND BUS (BACK) VCC BUS (FRONT) NC ENABLE 0.1F NC OUTPUT 10 mm MAX. (SEE NOTE 5) Figure 17. Recommended printed circuit board layout. 19 SINGLE CHANNEL DEVICE ILLUSTRATED. SINGLE CHANNEL DEVICE VCC1 5V 5V 8 VCC2 390 470 IF 2 6 + D1* VF - GND 1 0.1 F BYPASS 3 5 SHIELD GND 2 VE 7 1 2 *DIODE D1 (1N916 OR EQUIVALENT) IS NOT REQUIRED FOR UNITS WITH OPEN COLLECTOR OUTPUT. DUAL CHANNEL DEVICE CHANNEL 1 SHOWN VCC1 5 V 5V 8 VCC2 390 470 IF 1 7 + D1* 0.1 F BYPASS VF - GND 1 2 5 1 Figure 18. Recommended TTL/LSTTL to TTL/LSTTL interface circuit. 20 GND 2 SHIELD 2 Propagation Delay, Pulse-Width Distortion and Propagation Delay Skew Propagation delay is a figure of merit which describes how quickly a logic signal propagates through a system. The propagation delay from low to high (tPLH) is the amount of time required for an input signal to propagate to the output, causing the output to change from low to high. Similarly, the propagation delay from high to low (tPHL) is the amount of time required for the input signal to propagate to the output causing the output to change from high to low (see Figure 8). Pulse-width distortion (PWD) results when tPLH and tPHL differ in value. PWD is defined as the difference between tPLH and tPHL and often determines the maximum data rate capability of a transmission system. PWD can be expressed in percent by dividing the PWD (in ns) by the minimum pulse width (in ns) being transmitted. Typically, PWD on the order of 20-30% of the minimum pulse width is tolerable; the exact figure depends on the particular application (RS232, RS422, T-l, etc.). Propagation delay skew, tPSK, is an important parameter to consider in parallel data applications where synchronization of signals on parallel data lines is a concern. If the parallel data is being sent through a group of optocouplers, differences in propagation delays will cause the data to arrive at the outputs of the optocouplers at different times. If this difference in propagation delays is large enough, it will determine the maximum rate at which parallel data can be sent through the optocouplers. Propagation delay skew is defined as the difference between the minimum and maximum propagation delays, either tPLH or tPHL, for any given group of optocouplers which are operating under the same conditions (i.e., the same drive current, supply voltage, output load, and operating temperature). As illustrated in Figure 19, if the in- puts of a group of optocouplers are switched either ON or OFF at the same time, tPSK is the difference between the shortest propagation delay, either tPLH or tPHL, and the longest propagation delay, either tPLH or tPHL. As mentioned earlier, tPSK can determine the maximum parallel data transmission rate. Figure 20 is the timing diagram of a typical parallel data application with both the clock and the data lines being sent through optocouplers. The figure shows data and clock signals at the inputs and outputs of the optocouplers. To obtain the maximum data transmission rate, both edges of the clock signal are being used to clock the data; if only one edge were used, the clock signal would need to be twice as fast. Propagation delay skew represents the uncertainty of where an edge might be after being sent through an optocoupler. Figure 20 shows that there will be uncertainty in both the data and the clock lines. It is important that these two areas of uncertainty not overlap, otherwise the clock signal might arrive before all of the data outputs have settled, or some of the data outputs may start to change before the clock signal has arrived. From these considerations, the absolute minimum pulse width that can be sent through optocouplers in a parallel application is twice tPSK. A cautious design should use a slightly longer pulse width to ensure that any additional uncertainty in the rest of the circuit does not cause a problem. The tPSK specified optocouplers offer the advantages of guaranteed specifications for propagation delays, pulsewidth distortion and propagation delay skew over the recommended temperature, input current, and power supply ranges. DATA IF 50% INPUTS CLOCK 1.5 V VO IF 50% DATA OUTPUTS VO 1.5 V t PSK CLOCK t PSK t PSK Figure 19. Illustration of propagation delay skew - tPSK. 21 Figure 20. Parallel data transmission example. For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright (c) 2005-2012 Avago Technologies Limited. All rights reserved. Obsoletes AV02-0170EN AV02-0940EN - February 16, 2012