AR0132AT6C00XPEAH3-GEVB AR0132AT Evaluation Board User's Manual www.onsemi.com Evaluation Board Overview The evaluation boards are designed to demonstrate the features of image sensors products from ON Semiconductor. This headboard is intended to plug directly into the Demo 3 system. Test points and jumpers on the board provide access to the clock, I/Os, and other miscellaneous signals. EVAL BOARD USER'S MANUAL Features * Clock Input Default - 27 MHz Crystal Oscillator Optional Demo 3 Controlled MClk Two-wire Serial Interface Selectable Base Address Parallel Interface HiSPi (High Speed Serial Pixel) Interface ROHS Compliant * * * * Figure 1. AR0132AT Evaluation Board Block Diagram Figure 2. Block Diagram of AR0132AT6C00XPEAH3-GEVB (c) Semiconductor Components Industries, LLC, 2016 January, 2016 - Rev. 0 1 Publication Order Number: EVBUM2347/D AR0132AT6C00XPEAH3-GEVB Top View RESET Switch SW1 CLK Sel P19 Parallel O/P P6 TEST P5 I2C Bypass P24 EEPROM ADDR Sel P27 FLASH P7 ATEST P14 I/O Voltage Sel P16 STANDBY P8 I2C ADDR Sel P4 HiSPi Mode Sel P18 Figure 3. Top View of the Board - Default Jumpers Bottom View Baseboard Connector J1 Figure 4. Bottom View of the Board - Connector www.onsemi.com 2 AR0132AT6C00XPEAH3-GEVB Jumper Pin Locations The jumpers on headboards start with Pin 1 on the leftmost side of the pin. Grouped jumpers increase in pin size with each jumper added. Pin 1 Pins 1-4 Figure 5. Pin Locations for a Single Jumper. Pin 1 is Located at the Leftmost Side and Increases as it Moves to the Right Pin 1 Pins 1 and 2 Pins 3 and 4 Pins 5 and 6 Pins 7 and 8 Pins 9 and 10 Figure 6. Pin Locations and Assignments of Grouped Jumpers. Pin 1 is Located at the Top-Left Corner and Increases in a Zigzag Fashion Shown in the Picture Jumper/Header Functions & Default Positions Table 1. JUMPERS AND HEADERS Jumper/Header No. Jumper/Header Name Pins Description P3 VPP Open P4 SADDR 2-3 (Default) I2C Address Set to 0x20 1-2 I2C Address Set to 0x30 P5 TEST P6 OE_N OTPM Programming Voltage Not Supplied 2-3 (Default) Open Set to Test Mode 2-3 (Default) Open P7 FLASH Set to Normal Mode Parallel Output Enabled Parallel Output Disabled; HiSPi Output Enabled 1 +5V0 2 GND 3 FLASH 4 +3V3 P8 STANDBY 2-3 (Default) Normal Mode 1-2 Standby Mode P14 ATEST 1-2 (Default) ATEST GND P16 VDD_IO 1-2 (Default) 1.8 V Operation of Sensor 2-3 2.8 V Operation of Sensor P18 HiSPi Mode 1-2 (Default) 2-3 SLVS Mode Hi-VCM Mode www.onsemi.com 3 AR0132AT6C00XPEAH3-GEVB Table 1. JUMPERS AND HEADERS (continued) Jumper/Header No. Jumper/Header Name Pins Description P19 Master Clock 1-2 (Default) P24 I2C 1-2 & 3-4 (Default) Demo 3 SCL & SDA Connected to Sensor SCL & SDA Respectively P27 EEPROM Addr. Sel 3-4 Open & 1-2 Closed (Default) EEPROM Address Set to 0xA8 3-4 Open & 1-2 Closed EEPROM Address Set to 0xAC 3-4 Open & 1-2 Closed EEPROM Address Set to 0xA4 3-4 Open & 1-2 Closed EEPROM Address Set to 0xA0 On-Board Oscillator (27 MHz) 2-3 P28 TRIGGER SW1 RESET AR0132 Evaluation Board MCLK 1-2 Trigger Input Enabled Open (Default) N/A Connect Generator Between Pin 1 and GND When Pushed, 240 ms Reset Signal will be Sent to AR0132 Interfacing to ON Semiconductor Demo 3 Baseboard The ON Semiconductor Demo 3 baseboard has a similar 52-pin connector which mates with J1 of the headboard. The four mounting holes secure the baseboard and the headboard with spacers and screws. www.onsemi.com 4 ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. The evaluation board/kit (research and development board/kit) (hereinafter the "board") is not a finished product and is as such not available for sale to consumers. The board is only intended for research, development, demonstration and evaluation purposes and should as such only be used in laboratory/development areas by persons with an engineering/technical training and familiar with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling. Any other use, resale or redistribution for any other purpose is strictly prohibited. The board is delivered "AS IS" and without warranty of any kind including, but not limited to, that the board is production-worthy, that the functions contained in the board will meet your requirements, or that the operation of the board will be uninterrupted or error free. ON Semiconductor expressly disclaims all warranties, express, implied or otherwise, including without limitation, warranties of fitness for a particular purpose and non-infringement of intellectual property rights. ON Semiconductor reserves the right to make changes without further notice to any board. You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or design information or advice, quality characterization, reliability data or other services provided by ON Semiconductor shall not constitute any representation or warranty by ON Semiconductor, and no additional obligations or liabilities shall arise from ON Semiconductor having provided such information or services. The boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar or equivalent classification in a foreign jurisdiction, or any devices intended for implantation in the human body. Should you purchase or use the board for any such unintended or unauthorized application, you shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the board. This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and may not meet the technical requirements of these or other related directives. FCC WARNING - This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by ON Semiconductor to be a finished end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference. ON Semiconductor does not convey any license under its patent rights nor the rights of others. LIMITATIONS OF LIABILITY: ON Semiconductor shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of requalification, delay, loss of profits or goodwill, arising out of or in connection with the board, even if ON Semiconductor is advised of the possibility of such damages. In no event shall ON Semiconductor's aggregate liability from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any. For more information and documentation, please visit www.onsemi.com. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800-282-9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative