© Semiconductor Components Industries, LLC, 2016
January, 2016 − Rev. 0
1Publication Order Number:
EVBUM2347/D
AR0132AT6C00XPEAH3-GEVB
AR0132AT Evaluation Board
User's Manual
Evaluation Board Overview
The evaluation boards are designed to demonstrate the features of
image sensors products from ON Semiconductor. This headboard is
intended to plug directly into the Demo 3 system. Test points and
jumpers on the board provide access to the clock, I/Os, and other
miscellaneous signals.
Features
•Clock Input
♦Default – 27 MHz Crystal Oscillator
♦Optional Demo 3 Controlled MClk
•Two-wire Serial Interface
♦Selectable Base Address
•Parallel Interface
•HiSPi (High Speed Serial Pixel) Interface
•ROHS Compliant
Block Diagram
Figure 2. Block Diagram of AR0132AT6C00XPEAH3−GEVB
www.onsemi.com
EVAL BOARD USER’S MANUAL
Figure 1. AR0132AT Evaluation Board
AR0132AT6C00XPEAH3−GEVB
www.onsemi.com
2
Top View
Figure 3. Top View of the Board − Default Jumpers
FLASH P7
CLK Sel P19
RESET Switch SW1
I2C Bypass P24
EEPROM ADDR Sel P27
I/O Voltage Sel P16
HiSPi Mode Sel P18
ATEST P14
TEST P5
Parallel O/P P6
STANDBY P8
I2C ADDR Sel P4
Bottom View
Figure 4. Bottom View of the Board − Connector
Baseboard Connector J1
AR0132AT6C00XPEAH3−GEVB
www.onsemi.com
3
Jumper Pin Locations
The jumpers on headboards start with Pin 1 on the
leftmost side of the pin. Grouped jumpers increase in pin
size with each jumper added.
Figure 5. Pin Locations for a Single Jumper. Pin 1 is Located at the Leftmost Side
and Increases as it Moves to the Right
Pins 1−4Pin 1
Figure 6. Pin Locations and Assignments of Grouped Jumpers.
Pin 1 is Located at the Top-Left Corner and Increases in a Zigzag Fashion Shown in the Picture
Pins 1 and 2Pin 1
Pins 3 and 4
Pins 5 and 6
Pins 7 and 8
Pins 9 and 10
Jumper/Header Functions & Default Positions
Table 1. JUMPERS AND HEADERS
Jumper/Header No. Jumper/Header Name Pins Description
P3 VPP Open OTPM Programming Voltage Not Supplied
P4 SADDR 2−3 (Default) I2C Address Set to 0x20
1−2 I2C Address Set to 0x30
P5 TEST 2−3 (Default) Set to Normal Mode
Open Set to Test Mode
P6 OE_N 2−3 (Default) Parallel Output Enabled
Open Parallel Output Disabled; HiSPi Output Enabled
P7 FLASH 1 +5V0
2 GND
3 FLASH
4 +3V3
P8 STANDBY 2−3 (Default) Normal Mode
1−2Standby Mode
P14 ATEST 1−2 (Default) ATEST → GND
P16 VDD_IO 1−2 (Default) 1.8 V Operation of Sensor
2−32.8 V Operation of Sensor
P18 HiSPi Mode 1−2 (Default) SLVS Mode
2−3Hi-VCM Mode
AR0132AT6C00XPEAH3−GEVB
www.onsemi.com
4
Table 1. JUMPERS AND HEADERS (continued)
Jumper/Header No. DescriptionPinsJumper/Header Name
P19 Master Clock 1−2 (Default) On-Board Oscillator (27 MHz)
2−3AR0132 Evaluation Board MCLK
P24 I2C 1−2 & 3−4 (Default) Demo 3 SCL & SDA Connected to Sensor SCL & SDA
Respectively
P27 EEPROM Addr. Sel 3−4 Open &
1−2 Closed (Default)
EEPROM Address Set to 0xA8
3−4 Open &
1−2 Closed
EEPROM Address Set to 0xAC
3−4 Open &
1−2 Closed
EEPROM Address Set to 0xA4
3−4 Open &
1−2 Closed
EEPROM Address Set to 0xA0
P28 TRIGGER 1−2Trigger Input Enabled
Open (Default) Connect Generator Between Pin 1 and GND
SW1 RESET N/A When Pushed, 240 ms Reset Signal will be Sent to
AR0132
Interfacing to ON Semiconductor Demo 3 Baseboard
The ON Semiconductor Demo 3 baseboard has a similar
52-pin connector which mates with J1 of the headboard.
The four mounting holes secure the baseboard and the
headboard with spacers and screws.
www.onsemi.com
1
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or
other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s
product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is
subject to all applicable copyright laws and is not for resale in any manner.
The evaluation board/kit (research and development board/kit) (hereinafter the “board”) is not a finished product and is as such not available for sale to consumers. The board is only intended
for research, development, demonstration and evaluation purposes and should as such only be used in laboratory/development areas by persons with an engineering/technical training
and familiar with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling.
Any other use, resale or redistribution for any other purpose is strictly prohibited.
The board is delivered “AS IS” and without warranty of any kind including, but not limited to, that the board is production−worthy, that the functions contained in the board will meet your
requirements, or that the operation of the board will be uninterrupted or error free. ON Semiconductor expressly disclaims all warranties, express, implied or otherwise, including without
limitation, warranties of fitness for a particular purpose and non−infringement of intellectual property rights.
ON Semiconductor reserves the right to make changes without further notice to any board.
You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems
that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or design
information or advice, quality characterization, reliability data or other services provided by ON Semiconductor shall not constitute any representation or warranty by ON Semiconductor,
and no additional obligations or liabilities shall arise from ON Semiconductor having provided such information or services.
The boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar or equivalent classification in
a foreign jurisdiction, or any devices intended for implantation in the human body. Should you purchase or use the board for any such unintended or unauthorized application, you shall
indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor
was negligent regarding the design or manufacture of the board.
This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC,
CE or UL, and may not meet the technical requirements of these or other related directives.
FCC WARNING – This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by ON Semiconductor to
be a finished end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices
pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio
communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference.
ON Semiconductor does not convey any license under its patent rights nor the rights of others.
LIMITATIONS OF LIABILITY: ON Semiconductor shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of
requalification, delay, loss of profits or goodwill, arising out of or in connection with the board, even if ON Semiconductor is advised of the possibility of such damages. In no event shall
ON Semiconductor’s aggregate liability from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any.
For more information and documentation, please visit www.onsemi.com.
PUBLICATION ORDERING INFORMATION
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
◊
